Search Documents

By Jean-Sébastien Kroll-Rabotin, Éric Climent, Florent Bourgeois

"Falcon concentrators are enhanced gravity separators designed for concentrating fine and ultrafine slurries. The Falcon UF model is unique in that it is dedicated to beneficiation of ultrafines, one key feature being that it does not make use of any fluidisation water. In a former study, we investigated the physical mechanisms that govern the transport of ultrafine particles (in the range 10 to 80 µm) inside Falcon UF concentrators, and concluded that separation efficiency is governed by differential settling. Initially, we derived and published a predictive model of the partition function under dilute conditions. The present paper proposes an extension of the initial model to concentrated ultrafine suspensions for application to industrial scenarios. The paper discusses how hindered settling has been added into the initial model to account for solid concentration effects. The modified model is tested against experiments carried out with a laboratory scale UF Falcon concentrator from dilute conditions up to 30 vol%. A good agreement between measurements and model predictions is obtained, which confirms that our hypotheses about the physics of separation inside a UF Falcon separator remain valid even at high concentrations.INTRODUCTIONThe Falcon concentrator is a fast spinning bowl that is fed at its centre of rotation. It uses centrifugal force to separate particles that are transported inside a thin liquid film that flows upward along the inclined wall of the bowl (McAlister and Armstrong, 1998). Due to differential settling, dense and coarse particles are concentrated inside the bowl whereas light and fine particles are rejected with the overflow stream. The fast rotation speed of the bowl yields high centrifugal force several hundred times the attraction of Earth. Despite the thinness of the liquid film (between 100 µm and 1 mm with a Falcon L40) where separation takes place, the Falcon concentrator can treat high flowrates (up to 30 L/min). At the bottom of the bowl, an impeller transmits the bowl rotation to the feed, which drains upward by centrifugal force as soon as it hits the base of the spinning bowl (Figure 1)."

Jan 1, 2011

By R. Patrick

As a unique South African organisation, CSIR: Division of Mining Technology (Miningtek) strives to support the mining industry by improving health, safety and productivity through developing, adapting and transferring technology. Considerable effort is currently directed towards the development of potential non-explosive mining methods with the potential to allow continuous mining in narrow reef conditions. Besides improving productivity, continuous mining results in concentrated mining which has a significant impact on reducing infrastructural costs. Impact Ripping and Water Pulse Rock Breaking have been tried on gold mines, whereas Activation, Mini-Disc? cutting and the Plasma Holemaker are currently being tested on platinum mines. The organisation?s many years of experience in novel rockbreaking, together with its world-wide collaborator network, has placed it in a unique position to assist the mining industry and manufacturers in developing and/or adapting existing technologies for application underground. Currently a range of technologies are being investigated, which have reached different stages of maturity. The main technologies under investigation are; - Impact ripper system - Water pulse rock breaking - Activated undercutting rollers - Mini disc cutters - Electric rock breaking

Oct 1, 2001

By R. W. Mei, R. A. Strombom, D. J. Moore

"Heat-shrinkable cable accessories are solving problems in the mining industry. This paper describes a range of products used by the industry, including low-voltage splices, high-voltage splices to 8.7 k V, cable repair sleeves, mining cable terminations used on system voltages up to 25 kV and motor connection kits up to 8 k V. Technical procedures and designs are illustrated.IntroductionThe development of high-performance heat-shrinkable materials slightly over 20 years ago proved to be one of the major technological breakthroughs in power cable accessories. Heat-shrinkable products were introduced initially for use as low-volt age cable accessories in the aircraft and electronics industry. A program of continuous development and product introduction now enables the manufacturer to offer a broad range of products for mining, industrial and utility electrical systems.With the advent of atomic energy, an important discovery was made-exposure of some plastic materials to high-energy electrons can cause the permanent crosslinking, or intermolecular joining, of adjacent molecules. Once the material has been crosslinked, it will not melt or flow at any temperature.The unique properties of heat-shrinkable products also result from the exposure of special thermoplastic formulations to high-energy electrons. Because of crosslinking, these products have perfect elastic memory. The heat-shrinkable products are supplied in expanded condition. When heated, they will shrink and tightly cover the object over which they have been placed. 'The functional and operating demands of mine cable accessories exceeded the classic electronic applications of heat shrinkable materials. These demands required a very sophisticated program to develop materials and adhesive systems that could endure the operational environment associated with the mining industry,Ease of assembly, low installed cost and operational reliability are among the main reasons for the acceptance of heat-shrinkable mine cable accessories in electrically powered mines. For over a decade, these systems have been demonstrating proven performance."

Jan 1, 1980

By M. R. Saharan

A brief overview of rockburst control measures is presented. The paper then elaborates on one key rockburst control measure, which is known as destress blasting. A historical background of the technique is presented in order to understand different aspects of its field application. The publication enumerates key aspects of the technique as being used in practice in South Africa and North America. The paper also presents an analysis of three case studies in order to demonstrate difficulties associated with the field application of distress blasting in hard rock mines.

Jan 1, 2006

By R. L. Amelunxen

"In January 1983, Gibraltar Mines Ltd. started an exploratory program on Column Flotation with hopes of improving performance of the Molybdenum Cleaning circuit. The encouraging results led to a column test trial in the Bulk Copper Cleaner circuit where the test unit has per¬formed well. A program was undertaken to understand the mechanics of column operation. A year and a half later, Gibraltar is considering the replacement of existing Bulk Copper and Moly Cleaning flotation cells with a fully computer con¬trolled Column Flotation circuit.BRIEF SUMMARY OF TESTWORKInitial testwork was done with a home made 20 inch diameter x 31 foot high column, equipped with a doppler flow-meter at the tail line and automatic level conrol. This loop maintained constant level in the column by throttling the tail valve. This column was placed in a variety of locations around the Moly circuit as shown on Figure 1 a, b. Test re¬sults indicated that the column could achieve much higher grades than the conventional cells, but recovery wise, the performance was low. Spillages from overloaded pump boxes were a common frustration during this time.Column control strategy was reviewed; and, in light of information received from McGill University, changed to conform with the methods that had been employed by D. Wheeler, of the Column Co. of Canada4 and Gaspe Copper Mines3.The column was tested replacing a portion of the bank, figure lc. The results obtained were more or less equal to the circuit. However, as we had Nitrogen gas connected to the column and not the regular cells, the column was kept in service. With the use of Nitrogen in the column, the usual copper depressant, Sodium Cyanide could be replaced with Sodium Hydrosulphide, hence lower operating cost.As time went on, a 10 inch diameter column was added in series to re-treat the concentrate of the 20 inch diameter column with hopes that the copper content would decrease from 0.6% down to 0.3% in order to save on subsequent leach¬ing costs. So far, results indicate there has been some im-provement, hut we are not achieving 0.3% copper. (See figure 1d)."

Jan 1, 1985

By E. Wasmund

"Sandfire’s DeGrussa Copper-Gold operation in West Australia is a new high grade copper sulfide mine, which includes a 1.5 Mtpa concentrator which was completed in 2013.Early after commissioning, it was identified that the flotation capacity in the all-mechanical cleaner circuit was not sufficient. In order to improve recovery, the tail from the cleaner scavenger was sent back to feed the rougher scavengers. Test-work was done on-site to evaluate the possibility of using a flotation column as a pre-cleaner. A CavTube™ sparging system was selected, which is especially effective for fine ore particle flotation. Test-work was conducted at site using a 150 mm diameter unit, and then confirmed on a 500 mm diameter unit. A 4250 mm diameter full scale unit was installed in Q4 2014 and commissioned in Q1 2015. This unit gave some significant advantages including a reduction in re-grinding requirements, elimination of a circulating load and increase in the recovery of copper in the cleaner circuit and overall circuit.In this presentation, the benefits of columns and cavitation sparging for floating fine particles and rejecting fine entrained gangue will be explained. Also, the results from a lab unit and a pilot unit will be compared against the results of the full-scale unit. The paper will demonstrate the scalability of flotation columns, and which phenomena and scale-up criteria must be considered to be successful. Finally, some general observations will be made about the importance of columns in copper cleaning circuits.IntroductionSandfire Resources’ DeGrussa copper-gold concentrator is located approximately 900 km north-north-east of Perth in Western Australia. The project area landscape is scrubby mulga lands with few notable features. The climate is arid with high temperature and heavy summer downpours."

Jan 1, 2016

By Carlos Avalos Casillas, Saul Ortiz Landeros

The current work shows metallurgical results obtained at the Centro de Investigación y Desarrollo Tecnológico (Peñoles CIDT), as a continuation of the work first published in February 2012. With the aim of optimizing the economic values of the products, ores from San Julian (Fresnillo) were selectively floated to produce a lead concentrate and a zinc concentrate containing high silver values. In the laboratory, this included regrinding of the rougher and scavenger lead concentrate to increase the liberation of mineralogical species and thus lower zinc recovery. Cyanide leaching bottle tests were conducted to improve the value of the silver. It is proposed to leach the silver contained in the zinc concentrate and then recover the silver using the Merrill Crowe process. The results show a reduction of zinc recovery in the lead concentrate from 11.3% to 2.0% after regrinding to a P80 of 10 microns, improving the metallurgical quality and economic value of the lead and zinc concentrates. Also laboratory and pilot scale cyanidation tests showed that about 65 to 80% of silver will be leached from the zinc concentrate, after regrinding to a P80 of 10 microns. The proposed processing increases the economic recovery of silver from 72.7% to 78.8%.

Jan 1, 2014

By Y. Guglielmi, C. Gout, P. Henry, P. Dick

The key questions about fault reactivation in shales concern the potential enhanced fluid displacement through a previously low-permeability aseismic shale formation. Here we selected a critically-stressed fault cross-cutting the underground research facility of Tournemire (France) which is located in Toarcian shales. Several inclined boreholes were drilled across the 8.5 m thick fault zone characterized by a fractured damage zone (FDZ) and a central 2.4 m thick complex core (FC) made of multiple shear bands with gouge intercalated with highly fractured lenses. The fault was pressurized using a straddle packer system defining a 2.4m long injection chamber normal to the fault surface. Three fault zone intervals were tested, two in the fault damage zone and one in the fault core. A three-dimensional displacement sensor set in the chamber allowed continuous synchronous coupled monitoring of fault movements, injection pressure and flow rate. An anticlockwise 0.22-to-0.05 mm fault slip was captured associated with a 10-to-100 hydraulic aperture increase of the fault. Preliminary analyses of the experiments show that leakage in the fault zone is controlled by strength and stress magnitude contrasts between the fault core and the fault damage zone. Fault damage zone discontinuities display a much higher peak static friction angle than the fault core shear zones, respectively of 34 and 22° that could be related to complex interactions between healing and sealing processes. Fault core leakage is much more dependent on strain than on effective stress variations. Discontinuous, pulse-like leakage, develops following complex failure processes that may simultaneously take place in the gouge zones and along the large pre-existing discontinuities. Such results may be of importance in evaluating fault seal integrity in oil and gas exploration, production or CO2 storage or underground excavations monitoring.

Jan 1, 2015

By Olaf Andersen

Crucible melt extraction yields short metal fibers with eqivalent diameters as low as 50 µm from almost arbitrary metals and alloys. Highly porous components can be made from such fibers by suitable deposition and sintering methods. This technology is being developed at the Dresden based Department of Powder Metallurgy and Composite Materials of the Fraunhofer Institute for Manufacturing and Advanced Materials (IFAM) and has been applied to gold alloys and iron-base alloys containing small additions of precious metals. From the manufactured gold fibers, sintered structures were made for decorative applications. Additionally, it was found that due to rapid solidification during the fiber formation, precious metals can be finely dispersed in ironchromium- aluminum (FeCrAl) and FeAl20 alloys. Good catalytic activity at elevated temperatures was found in compositions containing 3 wt.-% Ce and 0.5 wt.-% Pt.

Oct 1, 2003

By P. Wells, P. Quinn

"A moveable flotation miniplant was designed and constructed at the research laboratory of Inco Technical Services Ltd. to address the need for flowsheet development with a limited amount of ore (such as drill cores). It consists of one rod mill, two regrind ball mills, one vibratory screen, 24 flotation cells of various sizes and two Venturi aerated flotation columns. The setup has continuous monitoring capability for pH, dissolved oxygen, oxidation-reduction potential, conductivity and temperature in conditioning tanks and flotation cells. Various options regarding flotation reagents, circuit configurations, and fineness of primary grind and regrind can be readily evaluated. The throughput of the miniplant is 20 – 30 kg/hour ore.Unit operations such as flash flotation, magnetic separation and gravity concentration can also be evaluated as an integral part of an entire flowsheet development.This communication describes the basic design features of the miniplant and some examples of applications are given.INTRODUCTIONInco operates numerous mines in Sudbury and Thompson and will shortly bring the Voisey’s Bay mine into production. It has long been recognized that the ores from different mines or from different depths of the same mine can give different responses in flotation. There is a growing need to properly evaluate the ores before feeding the mill to maximize the return of the mine/mill operation. Inco Technical Services Limited at Sheridan Park, Mississauga, Ontario has developed a batch laboratory procedure to address this issue. The results are considered in the overall economical assessment of new mine operations.For ores that cannot be processed by the existing mill operations or that will be processed by a new mill, it is necessary to develop a flowsheet that can maximize the economical return of the mine/mill operation. While recognizing the importance and contribution of the laboratory batch flotation procedure, it does not generate reliable data for flowsheet simulation and design. A full-scale pilot plant campaign is normally required to obtain the design data but often this is not possible due to a limited amount of ore obtainable from the drill core. A small-scale pilot plant (mini pilot plant or miniplant) capable of processing 20-30 kg/h ore can provide this data prior to a full-scale pilot plant campaign. A miniplant can also be used to optimize the circuit configurations, reagent additions and recycle options of process water before pilot plant work and can be used to test a different flowsheet configuration for an existing mill before re-piping a plant circuit."

Jan 1, 2003

By Nick Poushinsky

OVERVIEW OF PRESENTATION ?Stantec?s Northern Presence ?Challenges for Northern Development ?Environmental Approval Challenges ?History/Expectations ?Baseline Data ?Consultation ?Regulatory Processes ?Extra ?Regulatory ?Keys to Success

May 1, 2009

By J. Dong

"Xanthate is a sulfide collector that has been widely used in flotation for almost a century. It is inexpensive, easy to synthesize and apply, and produces good metallurgy in the right applications. However, a major drawback of xanthate is that it decomposes easily and generates CS2 gas in transportation, storage and operation, which can be harmful to human health. Also, excessive xanthate in tailings pond leads to toxicity of the process water and potential damages to aqua-life systems. New regulations in Ontario require that the TWA (time-weighted-average) value of CS2 in the work place is below 1 ppm, which is 1/10 of the previous limit. The stringent regulation may eventually sweep other regions of Canada with the increased awareness of healthy working conditions and environment protection. Therefore, it becomes very important to find xanthate replacements which will be “green”, i.e., environmentally friendly.In this research work, a systematic procedure is used for collector evaluation using the Sudbury nickel sulfide ores from Vale’s Ontario operations, starting with the collector properties (MSDS) evaluation, followed by batch flotation tests, miniplant tests, plant trials and economic evaluation. It is found that the most promising xanthate replacement is dithiocarbamate.INTRODUCTIONSulfide mineral flotation has been practiced since the early 20th century. Its industrial importance is well recognized as mineral concentrates from flotation can be economically smelted and refined to provide primary metals. Collectors play a vital role in froth flotation. There are reagents possessing both a polar group that binds them to the mineral surface and a nonpolar group that is oriented away from the surface to attach air bubbles. The introduction of xanthate as a sulfide collector in 1925 was a remarkable development in froth flotation (Keller, 1925). It is low cost, easy to synthesize, water soluble, simple to control in application. Most importantly, it has strong capability and usually good selectivity for sulfide mineral flotation, which have been keeping its application prominent for almost a century."

Jan 1, 2011

By Randy Clarkson

"Free gold particles occur in many base metal and precious metal mines throughout the world. Occasionally mine operators are unaware of the presence of free gold particles in their ores because they have not seen free gold hand specimens or at the working face of the mine.Due to the high density and malleability of gold, large circulating loads of free gold particles can build up over time in grinding circuits. This gold is often deposited in unintended traps throughout the mineral processing system.These unidentified free gold deposits represent a serious security risk as well as inaccessible inventory of gold. Deposits of free gold particles often remain undetected by mine management until they are accidentally discovered while repairing mill equipment. The trapping and subsequent release of gold particles can frustrate attempts to calculate accurate metallurgical balances.Nuclear tracers have been used to determine the free gold recovery efficiency of gravity recovery equipment, drills, and sampling equipment (Clarkson, 1994, 1997, 1998, 1999 and Walsh, 1986, 1992). In 1995, the author used radiotracers to locate and eliminate gold traps at La Mine Doyon (Clarkson, 1997). In 1998 and 2001, the author also salted mineral processing circuits at Royal Oak's Pamour Mine in Timmins (Clarkson, 1999) and at Gold Corp’s Red Lake Mine in Ontario with radioactive gold particles.The gamma and X-ray radiation from gold's nuclear isotope (Au198) were detected through steel, in pipes, and in moving equipment with scintillometers. The radiotracers proved to be a safe, rapid and accurate method of identifying gold traps, improving security, determining the recovery efficiency of Knelson gold concentrators and estimating retention times of gold particles in various processes."

Jan 1, 2003

By Bradford C. Wesstrom, Ricardo Parra

The Freeport McMoRan El Paso Refinery uses co-generation to produce some of its electricity and all of its steam. This paper will cover the operation of the co-generation plant natural gas turbine at a fixed RPM for blade longevity and energy output. The by-product heat from the turbine passes through boilers with additional heat from a duct burner to produce steam for the Tank House and auxiliary operations. The steam demand varies dramatically throughout the day based on unloading activities in the Tank House. The use of an automated steam control system within the El Paso Refinery will help stabilize line pressure by incrementally controlling steam consumption based on electrolyte temperature. This will minimize steam line pressure fluctuations. INTRODUCTION In the mid 1920’s the Nichols Copper Company of Laurel Hill, New York recognized the need for a modern copper refining facility in the southwest. Due to the many railroad heads, affordable power and abundant labor supply, and the close proximity to regional copper smelters in Mexico, Arizona, and New Mexico, El Paso became the logical location. In December 1928, ground was broken for the joint venture refinery between the Nichols Copper Company, Phelps Dodge, and the Calumet and Arizona Mining Company. In September 1930, Nichols Copper Company became a part of Phelps Dodge Corporation after a stock exchange. In July 1938, Nichols Division officially became Phelps Dodge Refining Corporation. In March 2007, Freeport McMoRan Copper & Gold acquired Phelps Dodge. Energy costs (electrical and thermal) are critically important in the viability of modern copper electrorefineries. The El Paso Refinery produces electricity and steam through its cogeneration system. The El Paso cogeneration facility is a natural gas, 15-megawatt facility containing five turbine generators and associated waste heat recovery boilers. The facility is divided into two phases. Phase I consists of two Allison 2.2-megawatt turbine generators. Phase II consists of three Solar Taurus 3.5-megawatt turbine generators. Presently three units in Phase II are operated. The Phase I units were purchased and installed in 1986 and the Phase II units in 1992 (Solar 1991). The facility operated at full capacity until 2003 when steam demand was significantly reduced due to decrease in cathode production and closure of the copper sulfate and precious metal operations. Phase I units were taken out of service and put on care and maintenance status.

Jan 1, 2019

By Paul Hughes

This paper summarizes current underhand paste backfill mining as applied to Goldcorp Inc?s Red Lake Mine, Newcrest Mining Ltd?s Kencana Mine and the Lanfranchi Nickel Mine as well as ongoing research at the University of British Columbia?s Norman B. Keevil Institute of Mining Engineering. The Red Lake Mine utilises a 6 m wide undercut with a 2 MPa unconfined strength paste in order to selectively mine its high grade, high-stress orebody. Kencana?s orebody is located in a poor rock mass environment. An 8 m wide, 2 MPa unconfined strength paste sill allows a safe working condition for its high grade orebody. The Lanfranchi Nickel Mine utilises a cable-supported, 2 MPa paste, with 12 m span sills, to optimize the mining of the squeezing rock mass. This paper details the rock mechanic hazards, ground support techniques, paste practices and unique conditions for each mine. Further, an update of ongoing research at the University of British Columbia, focussing on the optimization of safe mining in underhand cut-and-fill mining in high-stress/weak rock masses, is presented.

May 1, 2011

By D. J. Hallbom

This paper presents a novel methodology for the hydraulic design of mine backfill distribution systems. The ?operating range? method uses the concepts of the hydraulic grade line and equivalent pipe length to determine flows and pressures as the pipeline route and static head change over the life of the mine. The operating range method is easy to learn because it is semi-graphical and uses well-known design concepts (e.g., the hydraulic grade line) and slurry design models (e.g., the Durand deposition velocity model). However, by changing the paradigm in which these concepts are used, the operating method allows all potential pipeline cases to be analysed simultaneously without the need to know the exact pipe routing. It also allows the hydraulics engineer to quickly identify ?pinch points? and ?slack flow? zones, to estimate the effect of changing the size or length of any given section of pipe, to assess the impact of changing the material properties of the backfill slurry, to size the slurry pumps, and to size and locate rupture discs when required.

May 1, 2007

By G. R. Morin, A. R. Leggett

"In 2010, closure of the Kidd metallurgical plants along with structural changes to the historical ratios of payable metals led to a review of the operating targets at the Kidd concentrator. Previous operating data indicated that there was potential for significant revenue improvements by lowering the copper concentrate grade. An extended plant trial was carried out in 2011 to quantify the revenue impact of lowering the copper concentrate grade from 27% to 25% Cu, as well as identifying the lower practical grade limit. Analysis of plant trial results indicated that the process change increased net concentrate revenue by $2 M to $3 M per year at current metal prices. Increased revenue was primarily associated with higher silver recovery to the copper concentrate while the marginally improved copper recovery was essentially offset by increased zinc losses and concentrate treatment and freight charges.Details of the plant test work results are discussed in this paper along with the financial analysis of the revenue improvements. Key areas covered are major revenue components of the concentrate contracts, validation of revenue improvements through plant testing and sensitivity of the improvements to market and plant variables.INTRODUCTIONThe Xstrata Copper Kidd concentrator commenced operations in 1966 treating ore from the nearby Kidd volcanogenic massive sulphide deposit in Timmins, Ontario (Thompson, Amsden, & Chapman, 1978). Over the years, up to four separate grinding-flotation divisions were in operation with throughput rates peaking at 4.5 million tonnes per year of ore in the mid 1980’s (Kelebek & Francis, 1998). As the mine production decreased and grinding throughput increased operations were gradually cut back and since 1998 two grinding-flotation divisions have been in operation treating Kidd mine ore. One of the idled divisions has been intermittently used for custom milling operations, most recently the Ni/Cu Montcalm deposit, which was milled from 2004 to 2009. Current budget throughput rates, limited by mine production, are 2.4 million tonnes per year of ore grading 1.7% Cu, 4.3% Zn and 55 g/mt Ag. Concentrate production rates are 150,000 tonnes per year of copper concentrate and 155,000 tonnes per year of zinc concentrate. The Kidd mine is the deepest base metal mine in the world with mining operations down to 9600 ft.In 2010 the copper and zinc plants at the Kidd metallurgical site, which previously treated the concentrate production from the Kidd concentrator, ceased operation due to a variety of economic and market factors. Following the metallurgical plant closures the Kidd concentrator products were shipped off site for treatment. The majority of the copper concentrate is now processed at the Xstrata Copper Horne smelter in Rouyn-Noranda, Quebec with the majority of the zinc concentrate processed at Canadian Electrolytic Zinc Ltd. in Valleyfield, Quebec."

Jan 1, 2013

By Kjell Winther

"Hydralift Scanmec introduced early in the eighties a new and different mill design for very large grinding mills. The design described has actually no size limitation upwards and is so far suggested with motor power up to 40 MW. The mill is furnished with gearless ring motor drive transmission. It is totally fabricated, without heavy castings. The first installation, an 8, 1 MW ball mill dia. 6,5 m x 9,65 m length, has been in continous operation in 13 years without problems. Total grinding costs has been reduced with 3 0% compared to traditional smaller mills. Reductions has been achieved in maintenance cost, power consumption, liner wear and grinding media consumption.So far 3 ball mills of the described design are delivered and in operation, one grinding Iron ore and two grinding Nickel ore.IntroductionThe design of mills for mineral ore dressing has basically been unchanged since grinding in mills started some I 00 years ago, in spite of the fact that mills have grown larger and larger. This has resulted in structural and mechanical problems, causing expensive failures and loss of production.Hydralift Scanmec engineers were designing mills for more than 20 years according to the old «rules». As they experienced interest for an increase in the mill size at the time when reports about failing mills were published, they started analyzing the different mill parts to find new solutions. One goal was to only use elements from proven technology in the new design. Two key items were ring motor (wrap around motor)(Isch et al. 1977, Meintrup and Klein 1982, Ranze 1983) and large diameter pad bearings (wrap around bearings)(Fuller 1984), both acknowledged from other industries."

Jan 1, 1995

By Karl Nienhaus

The BGMR has developed a method for an online-analysis during drilling processes in cooperation with Fraunhofer Institute for Laser Technology in Aachen and various industrial partners. This allows for efficient utilization of deposits, maximum recovery of desired minerals and frequent and costefficient updates of deposit models. The used method, namely laser-induced breakdown spectroscopy (LIBS), was implemented into a compact demonstrator in order to analyze drill dust and loosened material within mining environments and directly on drill rigs. The consequently developed OFURanalyzer (OFUR ? online-analysis of mineral deposits) provides possibilities for exploration and visualization of deposit models in real-time and thus creates an opportunity for innovative applications, such as contactless, continuous quality control of minerals throughout the extraction process. A major challenge in the execution of this project was the necessity to develop a laser system that could withstand rough mining environments dominated by dust, shocks, vibration and therefore would be suited to operate under such conditions.

Oct 1, 2009

By Y. L. Su, S. Vongpaisal, H. A. Smith

"It is extremely difficult for a mine's central control room operator to control peakpower demands and to maintain normal materials handling operations at the same time. An investigation of the Falconbridge Strathcona Mine 's central control room has revealed that there are more than eight thousand possible combinations of ""situations"" that can arise. For such a circumstance, an expert system can become a very valuable tool to assist the operator in taking the most appropriate and timely action.A forward chaining expert system module has been developed for this application. The module is based on Level 5 ObjectTM software. It is graphics oriented and user-friendly. Training requirement is minimal.ForewordThis paper has arisen out of work carried out by YLS Associates and Falconbridge Limited as part of a contract between Falconbridge and the Department of Energy, Mines and Resources, Government of Canada, on the application of expert systems in mining operations.IntroductionThe electrical bill charged to large consumers by Ontario Hydro is based upon two elements: demand and energy consumption. The demand is the peak kilowatt level that the consumer has required during a monthly period. It is not uncommon for the demand portion to be as much as one third of the monthly bill. Energy consumption is the total kilowatt-hour s (kWh) consumed during the period.Ways to reduce the energy consumption part of the electrical bill involve utilizing energy-efficient equipment and operating machines in off-peak hours when a lower energy rate is charged. Maintaining the peak power below a critical level may require that simultaneous usage of major pieces of equipment be avoided. A 3000 kW skip run at an inopportune time could cost a company an extra $30,000 in that month's power cost.Potential disadvantages associated with peak power control are lost production due to work stoppage and increased operating costs due to the need to employ extra personnel. Most companies find these matters relatively easy to deal with and with incentives provided by Ontario Hydro, actively pursue this facet of energy savings (Harju , 1991)."

Jan 1, 1993