Search Documents

By T. E. Newkirk

In the past few years there has been considerable controversy on the most suitable material to be used in ventilation doors which will have to serve also as fire doors. For this reason it was thought useful at Mclntyre to find out to what extent our zinc chloride treated spruce doors were fire resistant and what protection we could expect in case of an underground fire. The doors to be tested were constructed of the same material as that used in our regular ventilation doors underground, namely, 2-inch tongue-and-groove well seasoned spuce. It is to be noted, however, that whereas the dimensions of the ventilation doors are 5 ft. by 6 ft., those of the test doors were only 14 in. by 17½ in. The treated doors were made up from lumber that l1ad been treated with chromated zinc chloride, as described in Mr. Keeley's paper. Two kinds of tests were carried out: a heat test and a flame test. An electric muffle furnace for assaying, equipped with a pyrometer, was used for the beat test, the furnace door being replaced by the wooden door to be tested. In the flame test, the door to be tested formed one end of a rectangular steel box in which was placed a large blow-torch. Air was admitted at the rear of the box. A pyrometer recorded the temperature at the inside surface of the door where flame impinged. The results of the tests are presented in the accompanying table, in which the word 'failed' is to be interpreted as meaning that the door had been damaged to the extent that smoke, but not necessarily flame, issued from its outside surface.

Jan 1, 1949

By Michel Aubertin

Using mine wastes as backfilling material for underground stopes has been a common practice for more than 60 years. Waste rock and tailings are used as filling materials because they are available at a reasonable cost to support the rock walls. Backfilling is also very advantageous because it reduces the amount of mine waste disposal on the surface. In underground mines, the backfill must first ensure stability of the opening, while increasing recovery of ore and minimising dilution. It is thus critical to accurately evaluate the pressures exerted on the walls and on the barricades placed near the base of the stope. In this presentation, existing solutions for evaluating the stresses on stope walls and barricades are briefly reviewed. The authors then present recently developed analytical solutions that take into account the stress transfer from the backfill to the walls in the stope and access drift. The stress state solution, which is based on arching theory, considers the influence of the stope geometry and barricade position within the drift. The method gives the pressure generated by partly or fully submerged backfill. The solutions apply shortly after backfill deposition, when the effect of pore water pressure cannot be neglected, and also for long term conditions under a fully drained state. Experimental testing and numerical modelling results are used to validate the proposed equations. Both numerical and analytical results show that the total pressure on barricades can be significantly increased by water pressure, while the effective stress is decreased (compared to dry or drained conditions). A discussion follows on the implications of the results for backfill applications.

Nov 1, 2008

By Kan Xing

This paper introduces common detrimental consequences to the environment from mining in the Beijing West Mining Area. For example, ongoing mining operations can cause the following environmental deterioration: rock burst, roof rises, roof falls and inrush (Pit dash for ward water). Post-closure, after minerals resources are exhausted, the following environmental issues may remain: landslides (collapse, and mud-rock flow), dropping or exhausted water tables, water pollution, desertification and soil erosion, water accumulation, Slay endanger, ground subsidence, and causal factors in seismic activity. This paper analyzes this wide range of environmental consequences of mining, and offers a theoretical foundation to underpin a corresponding management scheme.

Aug 1, 2013

By Simon C. Dominy, Alwyn E. Annels, Mark A. Noppé

Abstract - Mineral Resources and their subsequent conversion to Ore Reserves are of key importance to mining companies. Their reliable estimation is critical to both the confidence in a feasibility study, and also to the day-to-day operation of a mine. Together with sampling, assaying, geological and other errors introduced during interpretation and estimation, additional errors are likely to be introduced during the application of technical and economic parameters used for conversion of resources to reserves. There is thus a requirement for high-quality interpretation and estimation to be supported by high-quality data. Any company expecting to make sound investment or operational decisions must base this on both relevant and reliable information. An Ore Reserve statement generally contains a single set of grade and tonnage figures without a discussion of the potential inherent errors in these estimates. Some sensitivity studies may be run, but confidence limits are rarely quoted and, if they are, often do not take into account many of the factors that cause uncertainty in the grade and tonnage estimates. Mineral Resource and Ore Reserve estimates thus carry certain errors leading to uncertainty and risk; some of these are unquantifiable for various reasons, for which the operator should be aware. This paper presents a review of the potential sources of error that might occur during a resource estimation program, which are carried through into the reserve estimate. A number of methods are discussed that allow the estimator to be more transparent about the inherent risks in his/her estimate. Emphasis is placed on data quality, and the requirement for strong quality management to be linked to continuous improvement.

Jan 1, 2002

By Zhanyou Huang

The logic and capabilities of a short-term planning tool are presented. It was developed using mixed integer linear programming (MILP) techniques to solve the open-pit and underground mine planning problems that include multiple mining areas, multiple processes, multiple destinations and blending requirements. It finds the optimum schedule that achieves the objective while satisfying comprehensive product quality and quantity requirements, equipment utilizations, as well as physical and technical constraints. A case study is given to demonstrate its applications.

Oct 1, 2009

By Zhanyou Huang

The logic and capabilities of a short-term planning tool are presented. It was developed using mixed integer linear programming (MILP) techniques to solve the open-pit and underground mine planning problems that include multiple mining areas, multiple processes, multiple destinations and blending requirements. It finds the optimum schedule that achieves the objective while satisfying comprehensive product quality and quantity requirements, equipment utilizations, as well as physical and technical constraints. A case study is given to demonstrate its applications.

Oct 1, 2009

By R. Harris

The vacuum thermal route for magnesium production today accounts for roughly 80% of the global production of magnesium despite significant investment in the competing electrolytic technologies, This is up from 30% of the global production 10 years ago and is all the more significant because global magnesium production has more than doubled in the same time, A review of the sophisticated anhydrous magnesium chloride production technologies provides some explanation for this sea change in technology usage, However, an examination of the economic factors provides compelling reasons, The present review outlines some of the salient strengths and weaknesses of the competing technologies, It also offers suggestion as to where future R and D and economic effort needs to be vested to improve the sustainability of the world magnesium market in terms of its value and impact.

Jan 1, 2006

By Guocheng Pan

Geostatistics has been widely accepted as a standard tool for reserve estimation and mine planning. Kriging has been adopted as the best estimator of grade. Although many discussions have been conducted in the use of kriging in the mining industry, insufficient attention has been given to solutions for over-smoothing. This effect has been frequently encountered in many mines. The so-called over-smearing refers to two facts: (1) over-reduction of grade variabilities and (2) over-estimation of low-grade ore tonnages. This study attempts to link over-smoothing effects with several other practical aspects in kriging. These include the weight independence of data values, variogram modeling, and search strategy used in estimation. All solutions recommended here are suited for precious metal deposits (e.g. gold) in open-pit mining.

Jan 1, 1995

By J. W. Matousek

"Computer modeling of smelting processes requires internally consistent equations for calculating the compositions of mattes and slags. That is, the sum of the calculated assays must total 100%. One set of equations that satisfies this requirement for copper produced under oxidizing conditions (pSO2>one atmosphere pressure) is given by the following:%[Fe] = 62.0 – 0.775%[Cu]%[S] = 28.0 – 0.00125%[Cu]2%[O] = 10.0 – 0.225%[Cu] + 0.00125 %[Cu]2Mattes containing nickel in appreciable quantities do not have the defined “white metal” end point of approximately 80 percent copper and 20 percent sulphur that is found in the copper system during the converting process. The above equations, however, are readily extended to nickel and nickel/copper mattes for any desired end product composition."

Jan 1, 1996

By D. W. McDonald, N. A. Duke, R. L. Hauser

"The NERCO Con Mine is situated in the amphibolite facies aureole of the Western Plutonic Complex overprinting the Yellowknife Greenstone Belt. Metamorphic grade of the upright monoclinal basaltic succession decreases from hornblende-amphibolite facies along the border of the batholith to greenschist facies. Metamorphic isograds, subparalleling the faulted margin of the batholith, transect volcanic stratigraphy and coincide with major goldbearing shears.Gold mineralization is confined to north-striking, west-dipping shear zones where hangingwall amphibolite facies mineral assemblages retrogress to chlorite-carbonate-sericite-sulfide bearing schists hosting multiple generations of quartz-ankerite veins. The gold-producing portions of the Con and Campbell Shears occur where these structures transect an east trending thermal corridor. The corridor is defined by granitic plugs and a number of related breccia bodies, that can be traced outwards from the batholith across the greenstone belt.Prograde reactions of greenstone during amphibolitization effectively liberate fluids that partition metals. With retrograde reactions at shear zones, gold is precipitated with quartz due to the destabilization of sulfide and arsenic complexes. The coupling of regional prograde metamorphic and restricted retrograde metasomatic overprints suggest mineralization is temporally related to emplacement of the Western Plutonic Complex. Economic gold concentrations within the intrusive corridor indicates enhanced metamorphic overprint of hornfelsed greenstones enveloping satellite intrusives peripheral to the main batholith."

Jan 1, 1993

By M. Hashemzadeh

The efficiency of water use is a top priority for the global minerals industry, especially in regions with limited freshwater supplies. In these areas, the freshwater shortage has prompted mining companies to search for alternatives to freshwater sources. Seawater has been proven to be a potential water source for mineral beneficiation and metal extraction processes. This study compares chalcocite leaching behavior with ferric chloride to that with cupric chloride. We carried out leaching tests with a highly pure chalcocite sample in jacketed reactors under fully controlled pH and solution potential. The effect of chloride concentration, oxidant concentration, and temperature on copper extraction was quantified in both cupric and ferric chloride systems. In the ferric chloride system, increasing ferric concentration showed a positive effect on the first stage of chalcocite leaching. In the second stage, increasing temperature markedly enhanced copper extraction. In the cupric chloride system, chloride concentration presented a considerable effect on both the first and second stages of leaching, while temperature had a remarkable effect only on the second stage. The findings of this study would be beneficial to mine operations aiming to replace fresh water with seawater for heap leaching of chalcocite. INTRODUCTION Mineral processing operations/plants are normally operated adjacent to mines which are often located in remote and arid area, such as northern Chile, southern Peru and Australia with limited access to fresh water (Liu, Moran, & Vink, 2011, 2013). Water scarcity in these areas has prompted mining companies to invest in sustainable technologies to reduce the water use and/or increase the water use efficiency. One of the current sustainable approaches in mineral processing operations is to replace fresh water with seawater. Seawater is now being increasingly used for mineral beneficiation and metal extraction processes (Hernández et al., 2015). Another application of seawater could be for heap leaching of copper secondary sulfides, mainly chalcocite. However, the high concentration of chloride ion in seawater may significantly affect leaching kinetics of copper sulfide concentrates and ores (Watling et al., 2014). Therefore, it is essential to develop a fundamental understanding of the leaching of chalcocite in chloride media.

Jan 1, 2019

By Richard R. Klimpel

"This paper discusses the effect of water chemistry, reagent type, and other environmental factors on the performance of sulfide mineral size reduction and froth flotation processes. Two specific problems will be discussed: l.) the importance of appropriately utilizing the electrochemical window that is created in the grinding process to enhance sulfide mineral recovery by froth flotation; and 2) the impact of steel grinding media versus autogenous grinding on the efficiency of sulfide mineral flotation with varying thiol collectors and water sources.IntroductionThe mutual dependency between size reduction and mineral froth flotation is well recognized from the viewpoint of particle size and mineral liberation characteristics. The purpose of this paper is to discuss two less obvious industrial interactions between size reduction and froth flotation that have come up in the various plant optimization studies conducted by this author. These interactions are complex but appear to be important at the industrial level as plant throughput is directly affected, either positively or negatively by such interactions. Examples v.ill be given on how the method of grinding influences flotation and how different water sources influence the flotation behavior of electrochemically sensitive minerals. With each of these interactions, a number of fundamental research studies have shown previously that some effects can be measured under idealized and very small scale experiments. Such research studies will not be cataloged or exhaustingly reviewed in this paper. Whether these same types of effects can be measured in an industrial environment and are economically important is much less certain. This paper will present some rather unique experiences gained from larger scale test experiences which clearly indicate findings that plant operators should be aware of."

Jan 1, 1996

By Ken G. Stowe, Stephen L. Chryssoulis, Joe Y. Kim

"Lead ions originating from galena during processing of complex sulphide ores migrate to ""cover"" the surface of sphalerite and iron sulphide mineral rarticles, and cause poor selectivity in differential flotation. Generally in sulphide ore processing, the lead activated minerals float in the Cu/Pb circuit. Subsequently, surface lead complicates the zinc flotation circuit by lowering the concentrate grade due to the co-flotation of lead- activated iron sulphide minerals. The effect of lead in the differential flotation of sphalerite from Cu-Pb-Zn and Pb-Zn ores is discussed. Plant and laboratory test data are interpreted by determining the surface composition of individual grains of sphalerite and iron sulphide rarticles using two surface analytical techniques, Laser Ionization Mass Spectrometer (LIMS) and Time of Flight-Secondary Ion Mass Spectrometer (TOF-SIMS). Cationic and anionic species on the surface were analyzed to elucidate the phenomena.IntroductionSurface properties play a critical role in many aspects of mineral processing such as flotation, flocculation, etc. An understanding of interaction mechanisms of different reagents (inorganic cations and anions, collectors, regulators, etc.) with mineral surface in an aqueous solution is a very important pre-requisite in achieving the desired selective flotation. In the flotation of complex sulphide ores, the flotation collectors respond to the activation of minerals such as sphalerite, pyrite etc. by heavy metal ions of Cu, Pb or Ag, which is a strictly surface phenomenon."

Jan 1, 1995

By P. W. Ware

The majority of all refined copper is consumed to produce electrical conductors. Most copper conductors are drawn into wire from 8 mm ETP copper rod produced from high purity copper cathodes. Southwire Company has more than 40 years experience using, designing, fabricating and marketing a process for continuously producing ETP copper wire rod. This process is called the SCR® (Southwire Continuous Rod) process. Today, approximately half the copper wire rod produced in the world, or more than one third of all refined copper consumed, is produced using the SCR process. Southwire has sold 75 SCR copper rod mills to metal producers and wire manufacturers around the world. Southwire is North America's largest electrical wire and cable producer. Southwire operates a 48 metric ton per hour SCR® copper rod system in Carrollton, Georgia. This allows Southwire to provide technical support for existing SCR® system customers based on first-hand knowledge. Rod fabricators and their wire customers are always striving for copper rod that improves productivity. They are looking for improved surface quality, finer wire sizes and fewer wire breaks per ton of rod drawn. This paper will present a brief history of the SCR® process, a description and recent process developments.

Jan 1, 2007

By U. Martin

Advanced copper materials for conducting applications require an optimal combination of high mechanical strength at ambient and moderately elevated temperatures together with superior electrical and thermal conductivity. Mechanical alloying under repeated cooling of the milling vials in liquid nitrogen has been applied to produce ultra-fine grained (UFG) oxide dispersion strengthened (ODS) copper with a high yield strength at ambient temperature. In the present study ODS copper was manufactured by mechanical alloying of copper powder and 3% by volume of incoherent oxide dispersoids. During the high-energy milling a homogeneous distribution of fine dispersoid particles (diameter nearly 100 nm) can be achieved in the powder. Samples with a density of more then 97% of theoretical value were produced by uniaxial hot pressing under 650 MPa at 600°C for 20 minutes. The high yield strength at ambient temperature can be described by a linear superposition of the Orowan stress for particle hardening and of ultra-fine grain strengthening according to the Hall-Petch mechanism. Simultaneously, a best value of 75% IACS could be obtained for the electrical conductivity. The creep behaviour of ODS copper in the temperature range from 500°C to 700°C is described within the frame of diffusional creep deformation.

Jan 1, 2007

By M. Sabau

The Electrowinning Plant at INCO's Copper Cliff Nickel Refinery is a precious metals upgrading plant. The feed to the plant contains copper, nickel, cobalt, iron, significant amounts of precious metals and some impurities. Copper is the most abundant element in the feed. This paper describes the major equipment and process changes over the last twenty years, geared to improve the tankhouse operation, workroom environment and recovery of copper from the acidic solution. Copper is plated on to titanium blanks using explosion-bonded crossrods, animal glue as a levelling agent, and an organic surfactant for mist control. The installation of the stripping machine in 2001 required a number of changes: cathode and anode contacts were redesigned, flat bus bars were replaced with dog-bone type, spacer boards for cathodes and anodes were installed, longer anodes started to be used, and the plating cycle was extended from seven to fourteen days. A number of initiatives for improvement are being carried out. Explosion-bonded crossrods are being replaced with titanium-clad crossrods. The plan for the near future is to increase copper production by increasing current efficiency and current density. The possibility of lowering the iron concentration in electrolyte and changing the acid mist control method is being investigated.

Jan 1, 2007

By G. Viramontes-Gamboa

Approximately 70% of world copper reserves consist of the mineral chalcopyrite, and much international effort has focused on its study. Ultimate objectives include the development of environmentally friendly alternatives to smelting, and technologies to treat low-grade ores, for which concentration and smelting are economically unviable. Unfortunately, chalcopyrite leaching is inefficient in H2S04-Fe2(S04)3-FeS04 solutions, which is considered to be the most desirable oxidizing medium for leaching of copper sulfides, since the chemistry is well known, corrosion of industrial equipment is negligible, subsequent copper recovery by SXlEW is well established, and environmental impact is minimal. The main reason for this inefficiency is the self-passivation of chalcopyrite. We have devoted considerable effort in the understanding of this phenomenon, and have developed a predictive electrochemical methodology capable of establishing a priori the precise range of potentials within which chalcopyrite leaches and where it is passivated. Since potential control is a critical parameter in chalcopyrite leaching, this experimental methodology can be very useful for establishing the best conditions to leach chalcopyrite. In this paper, the scientific foundations of this predictive experimental technique are presented, and its practical application is demonstrated by comparing its predictions with leaching experiments from the literature.

Jan 1, 2007

By W. H. Hastings

Introductory In the amount of her coal reserves, Saskatchewan ranks third among the provinces of the Dominion, with a total, as estimated by D. B. Dowling, of 59,812,000,000 tons. All the coal so far discovered in the Province is lignite, and it would appear unlikely that bituminous or higher grade coals exist. General Occurrence of the Coal The location of the coal-bearing formations in Saskatchewan is shown on the accompanying map. It will be seen that the areas lie principally in the southern part of the Province. The more darkly shaded areas indicate locations where development is taking place, or where coal-seams are known to occur, either through outcrops in valley-sides or through having been encountered during boring operations. The coal-seams are not necessarily continuous throughout the shaded areas, but in all pans of these there are coal possibilities. It is quite possible that small outliers of the coal-bearing formations may occur further north in the Province, but, generally speaking, coal is not likely to be found outside the shaded areas.

Jan 1, 1929

By Jianping Zhang

QUESTIONS: ?? Is it more expensive to find an ounce of gold in Canada today than 50 yrs ago? ?? Did the Canadian gold industry find more gold than they mined? ?? What is the future sustainability of the Canadian gold industry? ANSWERS: ?? The gold discovery costs in real terms only increased slightly from 1946 to 2000. ?? Though the Canadian gold industry mined more gold than they discovered in the period, when undeveloped deposits are taken into account, the deficit was merely 12 million ounces. ?? The Canadian gold mining industry would be sustainable in the foreseeable future, particularly, given the overwhelming predicted promising gold market in the mid/long run.

May 1, 2006

By Oscar F. Tangel

This paper outlines Canada's current status in world iron ore markets, and evaluates the prospects for the future. Estimates for the production, export and consumption of iron ore are given. Canada's major market will continue to be the United States, with the European Common Market countries, Japan and the United Kingdom also forming important outlets. The advantages held by Canada's major competitors in these latter three market areas are briefly discussed.

Jan 1, 1966