Search Documents

By E. Sigal

Overview ?Intrinsik has completed several wide area HHRA and ERA studies of mining and smelting communities ?Several ?Lessons Learned? ?Key areas related to: ?Study Design ?Data Quality ?Bioaccessibility ?Speciation ?Weight-of-Evidence Approaches ?Advances in Ecological Risk Assessment Techniques

May 1, 2009

By Emmanuel Henry

The Kiruna Mine, operated by Luossavaara-Kiirunavaara AB (LKAB), is a large-scale sublevel caving operation located in Arctic Sweden. Iron ore is extracted at a rate of 60 000 tpd from a four-kilometre long, 80-100 m thick and 60-degree dipping orebody. Actual production depth is 800 m under the top of the footwall and about 550 m under the average regional ground level. Because no support is left between the footwall and the hanging wall and despite the relatively low mining depth, extraction results in the formation of a huge stress shield modifying the original stress field and concentrating it just beneath the mining level. Effects of stress concentration on the rock mass are monitored through field observations and a seismic system. Severe stress-induced deterioration of openings is visible to a certain radial distance from the mining level: pillar crushing and fault slips are more and more common and extended. The seismic system, installed in collaboration with CANMET, confirms the field observations and completes them in the rock mass: fault slips and major seismic events are recorded. The system proves its effectiveness to outline the extension of the dynamic response of the rock mass, which actually seems much larger than field observations let think.

May 1, 2001

By Mostafa Benzaazoua, Bruno Bussière, Jean Lelièvre

De nombreuses opérations mimères exploitent et traitent des minerais sulfurés pour concentrer des métaux precieux (Au, Ag ... ) OU des métaux de base (Cu, Pb, Zn ... ), laissant en fin de parcours des tonnages considérables de résidus plus ou moins générateurs de drainage minier acide (DMA) selon leur contenu en sulfures. De nos jours, Jes restrictions en matière de protection de l'environnement obligent Jes opérateurs miniers a trouver Jes solutions Jes plus efficaces pour préserver Jes sites environnants de la pollution due a l'oxydation des sulfures. Cette oxydation cause une acidification accrue du milieu et une mise en solution des metaux toxiques. L'utilisation des recouvrements multicouches est l'une des solutions Jes plus efficaces pour limiter la pollution liée au DMA mais entraine des coilts de construction qui sont souvent considérés par l'industrie miniere comme prohibitifs. Une façon de rendre cette technologie applicable, d'un point de vue économique, est de désulfurer Jes résidus à l'usine de traitement et d'utiliser la fraction inerte comme composante d'un recouvrernent multicouche. Cette opération de desulfuration peut etre réalisée par flottation non sélective des résidus dans le but d'obtenir d'une part un faible volume de concentré de sulfures qui devra être géré convenablement et d'autre part un rejet non générateur d'acide.

Jan 1, 1998

By H. Tokuichi, H. Ohta, K. Sato

A physical separation technique of tantalum capacitors from waste print circuit boards is in a development phase in Japan. A tantalum capacitor consists of an exterior coating of resin (epoxy resin) mixed with silica fillers and a sintered tantalum compact, the latter of which is impregnated with manganese dioxide (MnO2). In this study, we developed a process to recover tantalum oxide from tantalum capacitors by roasting, fluidized-bed separation, and hydrometallurgical treatments. Our aim was to recover tantalum oxide with high purity from waste tantalum capacitors. In this process, the exterior resin was selectively decomposed by roasting without oxidation and pulverization of the sintered tantalum compact at a proper temperature. Furthermore, the decomposed resin with silica filler on the surface of the sintered tantalum compact was mostly removed by fluidized-bed separation. The surface of the sintered tantalum compact was cleaned by ultrasonic irradiation in an acid solution to remove the MnO2 paste as well as residual Ag paste and silica filler. The impregnated MnO2 in the sintered tantalum compact was leached as Mn(II) ions using acid solutions via the reducing effect of tantalum metal to recover purified tantalum oxide.

Jan 1, 2014

By Pierre Beaudoin, Michel Bourassa, Robert Lanthier, Samir Chéfaï

"Mine Doyon, in collaboration with CRM's Process Control Division, improved the control strategy at the SAG mill I Ball mill grinding circuit. The project aimed at increasing operation stability and throughput. First, a needs analysis was achieved in order to define the control philosophy and to upgrade the process control equipments and instrumentation. The stabilizing control strategy has been developed and implemented successfully using single loop PID controllers. The monitoring feature as well as the rule based supervisory control strategy were implemented on 486PCs running Process Vision and COMDALE/C softwares. Main features of the control strategy are described in this paper while results are presented and discussed.RésuméLa Mine Doyon, en collaboration avec le service de contrôle des procédés du CRM, a optimisé la stratégie de contrôle au circuit de broyage. Les objectifs du projet étaient !'amélioration de la stabilité de !'ensemble de !'opération et la maximisation du tonnage usiné. Une analyse de besoins a été réalisée pour concevoir la philosophie de contrôle et déterminer les ajouts a apporter a I 'instrumentation et au systeme de contrôle. Une stratégie de contrôle à deux niveaux, integrant stabilisation et supervision, a été developpee et mise en opération. La regulation est réalisee par une combinaison de contrôleurs Moore de type PID. Le monitoring et la stratégie de contrôle a base de règles soot implantés sur des micro-ordinateurs de type PC/486 avec les logiciels ProcessVision et Comdale/C. Les principaux aspects de Ia stratégie de contrôle sont décrits dans cet article et les résultats obtenus soot présentés et discutés."

Jan 1, 1995

By J. F. Nie

Mechanical properties of precipitation hardenable magnesium alloys depend critically on the chemistry, structure, morphology, orientation and distribution of strengthening precipitates. It is therefore important to gain an improved understanding of these information and their correlations with mechanical properties. Our recent studies indicate that additions of 1-2 wt% of Zn to a Mg-6wt%Gd alloy result in a substantial enhancement in precipitation hardening and in creep resistance. If the strength and creep resistance of the resulting ternary alloy are to be further enhanced for commercial applications, then a detailed characterisation of the strengthening precipitates in these alloys is required. In the present study, the precipitates formed in a Mg-6Gd-1Zn-0.6Zr (wt%) alloy, peaked aged at 250°C, have been characterised in detail using transmission electron microscopy and 3-dimensional atom probe field-ion microscopy. It is found the peak-aged microstructure contains a dense and uniform distribution of precipitate plates that form on the basal plane of the matrix phase and are typically less than 1 nm in thickness. Detailed analyses of the structure and composition of these basal precipitate plates will be presented and discussed in the context of previous work on other Mg-RE¬Zn alloys of similar compositions.

Jan 1, 2006

Planning and operational problems Difficulty in getting accurate geological interpretation Hard to plan work in advance Constant changes in engineering drawings and specifications Occasionally, a small stope portion requires changing the mining method from room-and pillar to shrinkage The ground has to remain stable until the entire stope is mined out A large stope portion is mined as development (30%) Frequent corrective excavation work due to dip changes Unstable and inclined working surface Frequent rehabilitation work is required

Feb 1, 2008

By I. S. Zajac, Y. O. Oyediran, M. C. Robart

This paper presents an overview of the metallurgical work on the Strange Lake Alkalic Complex (SLAC), from historical development of the "Main Zone" to present day develoment of the "B Zone". The SLAC, originally discovered by the Iron Ore Company of Canada (IOC) in the northeastern Canadian Shield of Québec and Labrador, is one of the world’s largest deposits of rare earth elements (REE) including yttrium and high field strength elements (HFSE) including zirconium, niobium, and titanium. It is part of a Precambrian, post-tectonic complex of peralkaline granites which intruded along the contact between gneisses and monzonites of the Churchill Province of the Canadian Shield. Mineralization of interest at Strange Lake principally occurs within peralkaline granite-hosted pegmatite and aplite sheets and, to a lesser degree, within the host granites, particularly in intra-pegmatitic granites. The highest grade and metallurgically most favorable mineralization is in the upper, open pit mineable parts of the SLAC. Metallurgical development has been conducted under a number of mining companies, and various value metals have been targeted throughout the history of the deposit, including yttrium, zirconium, niobium, and rare earths. Historic processing routes tested have included ore beneficiation, atmospheric leaching, solvent extraction (SX), and metal precipitation. This paper also presents the metallurgical development supporting Quest Rare Minerals Ltd.’s (Quest) 2013 Pre-Feasibility Study (PFS) and 2014 Preliminary Economic Assessment (PEA).

Jan 1, 2014

By Behzad Vaziri Hassas, Firat Karakas, Esra Tanisali, Mehmet S. Çelik, Ahmad Hassanzadeh

Coagulation is basically an aggregation process where particles settle under the influence of interfacial forces with electrostatic forces playing a governing role. Although particle morphology consisting of shape and roughness dictates the physical encounter of two particles, their eventual coagulation is not only influenced by columbic forces but also other interfacial forces such as hydrophobic interaction, which affects the extent of aggregation of particles through increasing the distance of interaction. Roughness is well known to increase the effective contact angle on hydrophobic surfaces and also enhance interfacial forces. In this study, the effect of morphology of particles and particularly roughness on the settling velocity and in turn coagulation tendency was investigated. Batch settling tests (BSTs) of different particle morphologies were investigated as a function of pH. Two different morphologies of silica particles were utilized with the same particle size distribution (PSD) including smooth-spherical and rough-spherical (Etched). Rough particles were prepared by acid etching technique using hydrofluoric (HF) at different time intervals (15-300 sec). Etched samples were identified and quantified by optic profilometry. Settling test results showed that the settling velocity of particles in a suspension of 2% solids in the massive settling region is significantly affected by particle morphology of the suspension. Coagulation results further revealed that aggregation of rough particles is faster than smooth-spherical particles. Coagulation results are elucidated on the basis of particle morphology and its effect on distance of separation through hydrophobic forces.

Jan 1, 2016

By Weldon Li

Outline ?Introduction and Motivation ?Previous Research ?Details ?Findings ?Current Multi-Piece Mining Wheel Research ?Methodology ?Preliminary findings ?Current and Future Activities ?Summary and Closing Remarks

Oct 1, 2010

By F. Sheykh-Jaberi, S. L. Cockcroft, A. B. Phillion

A coupled fluid/structure model has been developed to simulate semi-solid deformation in an industrial aluminum casting alloy, A356. Although this alloy has a significant eutectic fraction, nearly 50%, it still shows susceptibility to hot tearing. The model geometry consists of solid grains, created from a Voronoi tessellation of the domain, surrounded by liquid. The simulation is performed using the commercial codes, Abaqus Standard and Abaqus CFD. The solid model calculates the velocity, stresses and distortions in response to an applied uniaxial strain, and transmits them to the fluid-flow model, which computes the velocity and pressure fields in the liquid. It was shown that grain size and configuration, fraction solid and fluid properties all affect the semi-solid deformation behaviour.

Jan 1, 2014

By Pierre Bénard

To achieve penetration on the energy market, hydrogen must overcome obstacles in the areas of storage, safety and infrastructure. One of the most important is the onboard storage of hydrogen for transportation applications, where large performance gaps exist between the current state of the technology and user expectations. In order to develop and demonstrate viable hydrogen storage technologies for cars, a set of gravimetric and volumetric system targets have been proposed by the US Department of Energy, based on achieving a driving range of 500 km for a hydrogen powered vehicle. A factor of 2 to 3 improvement in both hydrogen storage capacity and energy density is needed along with several other performance goals. Another key issue is safety. Although some of the safety issues can be arguably assigned to misperceptions, hydrogen has specific properties that have to be addressed, particularly in confined geometries where the risk of hydrogen detonations becomes an issue.

May 1, 2007

By Tom Shumka

INTRODUCTION ?This bull gear inspection technique was developed to provide more accurate data and faster inspection times than current techniques used today. ?Eddy Current Array (ECA) is a non-destructive testing technique that provides the ability to electronically drive multiple eddy current coils, which are placed side by side in the same probe assembly. Each individual eddy current coil in the probe produces a signal relative to the phase and amplitude of the structure below it. ?This data is referenced to an encoded position and time and represented graphically as a C-scan image. Most conventional eddy current flaw detection techniques can be reproduced with ECA inspections; however, the remarkable advantages of ECA technology allow improved inspection capabilities and significant time-savings.

Oct 1, 2010

By P. Condori, G. Rech, J. Winnett

"Palabora Mining Copper has a unique ore body composition which unlike other copper ore bodies has three main components in significant proportions; these are copper bearing ore, magnetite and dolerite. The high content of dolerite, a hard barren material, creates a high proportion of pebbles which normally are recycled back to the mill. This action increases the mill bearing pressure and power progressively until corrective actions are taken.A logical action to solve the pebbles generation would be to incorporate a pebble crusher. This in fact was done however two fundamental issues were encountered; the high content of magnetite and existence of a cyclone classification section. Due to the high content of magnetite, metal detectors have not been able to work efficiently to separate tramp metal which causes damage to the pebble crushers. The existence of cyclones in the circuit had a detrimental effect on the final product when the pebbles crusher was online producing coarse sandy material.Due to the difficulties in treating pebbles via conventional procedures and the unique Palabora ore composition and characteristics, sorting technology was investigated at laboratory and pilot scale. It was found that a combination of optical and electromagnetic sorting could efficiently separate dolerite from the copper bearing and magnetite ores.This paper reports the findings of the laboratory and pilot scale work performed and discusses the additional benefits to the circuit."

Jan 1, 2012

By M. Labrie, H. L. Gibson, G. Doiron, J. J. Watkins, D. H. Watkinson

The Corbet deposit is one of 17 proximal Cu-Zn massive sulfide deposits located. within the Noranda Cauldron which occurs within the core of the Noranda Volcanic Complex. The deposit is located at the top of the Havrian Formation, the lowermost formation of the 3000 m thick Mine Sequence; the deposit has Yielded 2.75 M tonnes of ore grading 3% Cu, 0.96% Zn, 2.06 g/t Ag and 1.0 g/t Au. The multi-lens Corbet deposit formed within a 250 m wide crater that occurs within a localized breccia pile. The Corbet breccia pile was constructed by explosive magmatic and hydrovolcanic eruptions localized along the south flank of a larger andesitic shield volcano that formed during the waning stages of Havrian volcanism. The breccia footwall of the deposit allowed unfocused and widespread hydrothermal discharge that resulted in the development of a large area of chlorite and fringing sericite alteration that exceeds, by six times, the size of the sulfide lenses and represents a significant exploration target.

Jan 1, 1993

By T. R. Bieler

"Hot forming and superplasticity in powder metallurgy aluminum alloys and composites is reviewed. The effects of alloy composition, particulate composition, size, and size distribution is summarized. The role of climb distance for recovery is described in connection with the size of strengthening phases. In materials with fine strengthening phases on the order of one micron or less, high strain rate superplastic deformation processes are likely. However, the quality of superplastic deformation depends on the prior processing history, and these effects are reviewed. Very few data describing the effects of hot forming history on post-forming properties exist, but some results emerging in the literature are compared.IntroductionHot deformation in aluminum based materials is done for several technological purposes, such as thermomechanical processing to alter mechanical properties of simple forms, and/or final shaping operations to produce a complex shaped part by means of extrusion, forging, or superplastic forming. In the interest of improving the mechanical properties of aluminum based materials, two microstructural design strategies are commonly used, dispersion strengthening, and composite strengthening. The introduction of fine, stable dispersions is commonly done for high temperature strength, and the dispersions are typically ceramic particles in the range of 10 nm to 1000 nm in volume fractions around 5 vol.% (Higashi et al., 1990; 1991a; 1991b; 1992; Bieler and Mukherjee, 1990; Otsuka et al., 1987; Bieler et al., 1991; Oliver and Nix, 1982). Alternatively, composite strengthening strategies using 10-40 v% of 3 µm to 40 µm ceramic particles provide high modulus and high strength aluminum based materials (Midling and Grong, 1995; Lloyd, 1994; Subramanian et al., 1995)."

Jan 1, 1997

By Denis Bois

La Bolivie est un pays en développement qui compte une tradition minière qui précède même l?établissement espagnol en Amérique. Pendant toutes ces années, l?exploitation minière s?est faite sans grands égards pour l?environnement. Au cours des dernières années cependant, le gouvernement bolivien a modifié ses lois afin de rendre nécessaire la prise en compte de l?environnement dans le processus d?exploitation d?une mine. Dans le cadre d?un projet MRN-ACDI1 visant à renforcer le secteur minier en Bolivie et ses retombées pour la population, l?URSTM2 a été mandaté pour développer et mettre en place un programme académique de gestion environnementale minière, basée sur l?expertise canadienne. Ce programme vise à renforcer les institutions académiques boliviennes responsables de la formation en environnement minier en Bolivie ainsi que les ministères et agences gouvernementales concernées.

May 1, 2001

By Anthony Finch

Many mines combine open pit with underground mining, and on many occasions the underground mine is an extension of the open-pit. In these circumstances the decision about where the open-pit stops and the underground starts is crucial and driven by many factors. This paper looks at some of the ways that this cut-over can be calculated and specifically examines the calculation of it using modern mine optimization software. The paper provides a case study which will review various outcomes using these techniques, and demonstrates the influence of various factors on the optimal transition cut-over point. Biographies Mr Finch is a Divisional Manager and a Principal consultant at Snowden Mining Industry Consultants in Vancouver, Canada. At Snowden Mr Finch leads a team of engineers that perform mining engineering studies for projects around the world. Prior to joining Snowden Mr Finch was the Mining Manager at Barrick?s Henty mine in Tasmania Australia. Prior to that Mr Finch has held a variety of roles in both consulting and operations working for various organisations at various levels in the Asia Pacific region. Mr Finch gained a bachelor?s degree in Mining Engineering from the University of Queensland in 1986, and a bachelor?s degree in Economics from the University of Queensland in 1993. His expertise is in mine planning, mine optimisation and mine management. Dr Elkington is a Consultant at Snowden Mining Industry Consultants in Perth, Australia. He is responsible for the design and implementation of Snowden?s proprietary optimization software products. Prior to joining Snowden Dr Elkington completed his PhD in Mine Optimisation at The University of Western Australia, and bachelor?s degrees in Engineering (Hons) and Commerce from The University of Western Australia. He specialises in optimization and trade-off studies, and has consulted on projects across all major commodities and regions.

May 1, 2011

By Chunlin Chen

Published data on thermodynamics of tin in liquid copper, matte and slag have been reviewed, assessed and used in development of thermodynamic solution models of melts. The developed model/database was applied in modelling the Sn deportment in primary copper smelting and e-waste melting processes. The results show that Sn can be removed from the matte through evaporation of various volatile Sn species (with SnS the most volatile) and slagging during copper smelting. The Sn removal increased with increasing matte grade due to the increased gas and slag volume. In the e-waste smelting process, fluxing strategy was developed for smelting e waste to produce a slag with reasonable liquidus and viscosity. Modelling results show that very low amounts of Sn reported to the gas phase due to low S, hence low SnS partial pressure in the system. The black copper produced could contain a few percent of Sn depending on the oxygen potential. The Sn in the black copper could be removed to the slag phase during anode refining. INTRODUCTION Tin is an impurity element commonly found in copper ores, which will be dispersed into various solid, liquid, and gaseous streams during the pyrometallurgical processing of copper. Tin alloy is widely used in electronic soldering due to its low melting point. The growth in treatment of recycled e-waste through primary and secondary copper smelting has led to an increased tin input to the smelting system. Therefore, the deportment of tin between phases is of great interest to the operators of modern smelters. Multi-Phase Equilibrium (MPE) is a thermodynamic package developed by CSIRO for simulating reactions between phases in multi-component and multi-phase systems (Zhang et al., 2002). Over the years the capability of the MPE model has been extended to cover the behavior of a large number of elements in high temperature system (Chen, Zhang, Wright, & Jahanshahi, 2006). In the present paper, the thermodynamic data on tin in liquid copper, matte and slag have been reviewed, assessed and used in the development of a database for Sn slag, alloy and matte phases. The model/database was applied in modelling the tin deportment in primary copper smelting and e-waste smelting processes. The aim of this study is to provide a better understanding of the chemical behaviours of tin in high-temperature copper processing and e-waste smelting.

Jan 1, 2019

By R. D. Brown

Higher metal prices have resulted not only in increased exploration and production, but also increased activity in the purchase of mining properties and mines. This article discusses some of the basic income tax considerations to be taken into account on the disposal of an interest in a mining claim or an active mining operation. It notes the importance ofan appropriate allocation of the purchase price amongst the various categories of assets, and discusses the tax implications to both vendor and purchaser of the transfer of the comm on types ofassets involved in mining operations. In the space available, the article can only outline the basic tax considerations, and point to areas where both vendor and purchaser need to be o

Jan 1, 1980