Search Documents

By K. Karan

Oxygen reduction reaction in PEM fuel cell cathodes involves participation of three reactants - oxygen, hydrogen ions, and electrons. Electrochemical reaction in the catalyst layer is, therefore, influenced by how these species are transported to the reaction site. The two-phase boundary locations at which percolating networks of ionically conducting electrolyte and electronically conducting Pt/C meet are feasible reaction sites. The electrolyte phase also provides pathway for the transport of dissolved oxygen. Most of the 3-D models describe the catalyst layer as an ultra-thin layer, thereby, losing useful information on the distribution of electrochemical reaction rate. In this paper, we extend our previous work on 2-D cross-the-channel modeling of PEMFC cathode based on agglomerate catalyst layer. In particular, we take a closer look at the influence of proton conductivity on the reaction rate distribution in the catalyst layer. As well, we re-examine the role of anisotropic transport coefficient of the porous transport layer (PTL), commonly known as the gas diffusion layer, on the current density distribution under the channel and the rib of the flow-field plates. Results from both a 2¬D and a 3-D models will be presented.

Jan 1, 2005

By X. Cao, B. S. Naik, D. L. Chen, P. Wanjara

AZ31B-H24 Mg alloy sheets with a thickness of 2 mm were friction stir lap welded (FSLWed) at two tool rotational rates of 1000 and 1500 rpm and two welding speeds of 10 and 20 mm/s. The tensile behavior of the FSLWed AZ31B-H24 Mg alloy was then evaluated at low (-40°C), room (25°C), and high (180°C) temperatures. It was observed that the failure load increased with decreasing tool rotational rate and increasing welding speed. The maximum failure load occurred at a tool rotational speed of 1000 rpm and a welding speed of 20 mm/s at all temperatures tested. It was also noticed that at the high test temperature, the samples failed along the sheet interface, i.e. shear fracture. At the low and room temperatures, the samples failed on the advancing side (AS) of the top sheet near the interface between thermo-mechanically affected zone (TMAZ) and stir zone (SZ). The different modes of fracture observed are associated with the hooking defect.

Jan 1, 2014

By Franco Chiesa, David Levasseur, Bernard Duchesne

A 500kg aluminium AlSi7Mg03 casting has been poured and the metallurgical quality at different locations inside the casting has been thoroughly investigated. It included measuring the local tensile properties (YS, UTS, El) in the T6 condition, the dendrite fineness (DAS) and the level of microporosity. A correlation was found between the microporosity level, the local solidification time and solidus front velocity; this correlation allows to predict the porosity level in large aluminium castings (solidification times between 20 and 200 minutes). Quite expectedly, properties varied widely within the casting and the actual mechanical properties were much less than the "textbook values" based on measurements carried out on separately cast standard specimens. A correlation between the secondary dendrite arm spacing (DAS) and the local solidification time was in keeping with previously published data. Finally the conditions to obtain an acceptable finish on machined surface were determined.

Jan 1, 2014

By Robert Voisey, Robert J. Spencer

"LynnGold's MacLellan Mine is located about 8 km south east of Lynn Lake immediately to the east of the Keewatin River (Fig. I). The property is accessible by an all-weather road, leading north from the provincial highway 391, which links with the Town of Leaf Rapids and the City of Thompson to the south.The ore body, as outlined in the original feasibility study, is expected to produce in excess of 9.3 x IQ6 gm of gold and silver over the next 5 years. However, the deposit is open to depth and exploration is continuing on and around the main zone and the many satellite deposits.The start of construction of the MacLellan Mine and mill was scheduled to phase in with the closure of the Fox copper-zinc mine located 48 km west of Lynn Lake. The majority of the employees from the Fox Operation were either employed at the MacLellan Mine or relocated to Sherrin's Ruttan Operation.GeologyThe MacLellan gold ore deposit is located on the northern section of the Lynn Lake Greenstone Belt known as the Rainbow Trend. This Trend is a 40 km gold bearing rock sequence extending both east and west from the MacLellan Mine. The southern section of these two east-west trending structures is known as the Johnson Shear, this is also gold bearing."

Jan 1, 1990

By A Smirnov

The problem of thin and very thin coal seam extraction is examined in a long perspective of Ukraine?s fuel and energy industry development. The technical and economic benefits of the coal seam selective mining technique are described, including beneficial environmental impact.

Aug 1, 2013

By C. O. Aksoy

"Pillars left to ensure the stability of major underground coal mine infrastructure (shafts, drifts) often contain substantial quantities of coal. Recovery of this coal is an efficient use of the resource, but often presents safety hazards; pillar extraction destabilizes the protected structure, and can make its use dangerous. In this study, the stability of an active shaft at an underground coal mine situated in the Soma- Manisa region of Turkey was investigated during the recovery of the coal in the shaft safety pillar.A proprietary three-dimensional finite element analysis model (ANSYS) was used. An elastic-plastic material model utilizing the Drucker-Prager failure criterion was employed. The three-dimensional Drucker-Prager formulation was preferred over the two-dimensional Mohr-Coulomb model because it was thought to more accurately represent the strain hardening behaviour shown by most geologic materials.Stresses and deformations formed around the shaft support were estimated using the model and the results were verified by in situ observations. The results show that stress distributions around the shaft and the subsidence of the shaft support are influenced by the location location of the extraction front and the break angle of the overlying material."

Jan 1, 2005

By M. R. Henzinger, W. Schubert

"The quality of the backfill applied at a shield driven tunnel is of significant importance failure of the lining. The used material also affects the interplay between support and excavation behaviour.In this research the state of the actual bedding situation is investigated by an analytical approach, laboratory tests and numerical simulations. The numerical simulation using continuum methods have shown shortcomings. These shortcomings regarding the instability of large strain simulations restrict the possibility to reproduce the relocation of the backfilling material. The performed scaled model tests have shown that the regripping process of a double shielded tunnel boring machine affects the soil failure within the gap. With the analytical results the influence of the wall friction can be predicted. Therefore the angle of the failure surface can be determined. The results have shown that the wall friction significantly increases the failure angle. INTRODUCTIONFor tunnel boring machines (TBM) with single (SM) or double (DSM) shield, precast liningsegments are used as rock support. These segmental linings are installed within the protection of the TBM shield. In order to reduce the friction while advancing, the shield diameter is smaller than the diameter of the cutter head and therefore also smaller than the excavation boundary. The difference depends on the expected radial convergences. Since the lining segments are mounted within the shield the steering gap between the shield and the excavation boundary increases and is hereinafter called annular gap.In the process of tunneling in hard rock, the annular gap is usually filled with fine grained and closely graded gravel, termed as pea gravel. The backfilling process starts as soon as possible after the shield tail passes the lining. Due to the operational procedure within the working area of a TBM, a fully backfilled annular gap might not be established after every ring closure. This leads to an unfavorable distribution of the pea gravel leaving the segmental lining partially without bedding. Segmental linings can develop sufficient resistance only when properly bedded."

Jan 1, 2015

By M. A. Bérubé

Le but principal de cette étude était de vérifier certaines hypothèses de nature minéralogique susceptibles d'expliquer en tout ou en partie les variations importantes observées au concentrateur no 1 de Mines Gaspé quant aux performances du circuit B de broyage et de flottation. A cette fin, nous avons examiné six séries d'échantillons prélevés lors d'une campagne de mesures effectuée au cours de l'été 1980. Ainsi, la capacité du circuit de broyage semble dépendre principalement devariation s dans les caractéristiques minéralogiqu es et texturales du minerai, par exemple du rapport grenat/quartz, le grenat ayant une influence néfaste sur le rendement de cette étape, contrairement au quartz . Quant au processus de concentration, la fraction du cuivre sous f orme de minéraux difficilement récupérés par flottation, en particulier des carbonates de cuivre, varie de façon significative dans le minerai, et cela peut certes expliquer en partie des récupérations parfois plus basses. Malgré ces variations important es de la composition minéralogique globale du minerai et de sa broyabilité, le degréde libération des sulfures de cuivre dans le produit de broyage dépend presque seulement de la granulométrie de ce produit. Afin de garantir des performances égales à l'étape de concentration, il est fortement suggéré de contrôler cette granulométrie à un niveau constant.

Jan 1, 1984

Fiabilité Totale d?Usine (FTU) Plan de la présentation ?Théorie de l?entretien ?Analyse comparative juin 2005 ?Session de travail 2005-2006 ?Suiviet Résultats(IndicateursdePerformance)

Feb 1, 2008

By D. Crone, T. Watts

"The Lindsley project was a program of deep drilling to test the contact down-dip from two nickel-copper deposits, one uneconomical and the other mined out. The role of Borehole Pulse EM(PEM) was to detect the higher grade, more massive sulphide zones if they were missed by a drillhole, and to help determine geometry if the zones were intersected. Two problems appeared as the PEM survey progressed: (1) conductivity-thickness as measured by the PEM did not always relate to economic sulphides as determined by the market; (2) a pattern of unusual PEM anomalies was obtained that indicated something odd and big, but the cause was unknown. A large fold structure subsequently was indicated by a program of deepening previous holes, the third of which intersected high-grade mineralization below 1280 m. Falconbridge is in the process of shaft sinking and underground exploration.IntroductionThe Falconbridge Lindsley property is on the south rim of the Sudbury basin, 8 Ian north of downtown Sudbury. The original property was acquired by a prospector named James Stobie, who, in early August 1885, staked a showing that later became the Mount Nickel mine (Fig. I). On August 10 Stobie staked another property that would become the Little Stobie mine, and at the end of the same month he staked the main Stobie orebody.In 1888, the ground immediately west of the MOlU1t Nickel find was staked. This ground contained the Blezard deposit (Fig. 1) which was put into production in 1889 and was eventually acquired by Inco. Down-dip from the Blezard workings, on Falconbridge ground, is located the upper Lindsley No. 1 deposit which was drilled off by Falconbridge in the 1940s to 1950s. A decision to go underground on the Lindsley No.1 mineralization was made in 1969, but the project was cancelled in 1971 because of declining nickel prices. The shaft was stopped at 95 m, and the headframe and hoist were sold. Further surface exploration drilling in the 1970s discovered the deeper Lindsley No. 2 zone, but as it had grades similar to those of the No. 1 zone, it too was considered uneconomic."

Jan 1, 1992

By X. Grant Chen, A. R. Farkoosh, M. Pekguleryuz

Nano-scale Al-(Fe,Mo)-Si dispersoids form during solution treatment in grain interiors (intradendritic regions) of cast Al7Si0.5Cu0.3Mg alloyed with 0.3Mo (wt.%). Unlike the Q-Al5Cu2Mg8Si6 and ?-Al2Cu age-hardening precipitates which coarsen resulting in loss of strength in Al-Si-Cu-Mg alloys, these Mo-containing dispersoids are thermally stable and retain their strengthening effect at elevated temperatures. Consequently, the age-hardened Al7Si0.5Cu0.3Mg0.3Mo (wt.%) exhibits high strength and creep resistance at 300 °C.

Jan 1, 2014

Train on Different Equipment - * Immersive?s interchangeable cabin controls technology - ?clip on & off? * Change Simulator from one machine to another in minutes * No technical expertise required to swap * Real, functioning, controls and displays are used to aid rapid learning Immersive has produced a range of Conversion Kits to suit most equipment. Modular design - Easy to convert from one machine model to another with a Conversion Kit. Caterpillar Models Trucks - 769D, 773D, 777D Trucks - 785B, 789B, 793B Trucks - 785C, 789C, 793C, 797 Excavator/Shovel - 5130, 5230 Front end loader ? 992, 994 Dozer ? D10, D11 Komatsu Models Trucks - HD325, 785-5, 985-5 Trucks - 730E, 830E, 930E Dozers - D375A-3, D475A-3 Shovel - PC8000 P&H Shovels - 4100A, 4100XPB, 4100BOSS Hitachi Shovels - EX2500, EX5500 O&K Shovel - RH200 Bell Articulated Truck - B40C

May 1, 2003

By H. K. Olsen, B. Thomassen, H. K. Schønwandt, L. Grahl-Madsen, H. Stendal

Abstract-The central part of the early Proterozoic Ketilidian orogen in South Greenland consists of an I-type granitoid batholith transected by four regional NE-SW-trending shear zones. The batholith was probably emplaced during subduction, from the south toward the Archaean craton in the north, in a sinistral transpressional system. A regional sediment sampling program covering 5000 km2 shows a close connection between a gold-mineralized trend and one of the major shear zones within the epizonal facies of the batholith. The gold mineralization is not directly related to the major shear zones, but occurs in quartz-veined and silicified second-order structures. High-grade (up to 114 ppm Au over 6 m) low-tonnage mineralization is found within these second-order structures cutting both amphibolites and granitoids. The mineralization is characterized by negligible or small alteration halos. Gold is associated with various element combinations of enhanced As-Bi-W- Cu, which indicate that the mineralization is mesothermal in origin.

Jan 1, 1995

By H. K. Olsen, B. Thomassen, H. K. Schønwandt, L. Grahl-Madsen, H. Stendal

The central part of the early Proterozoic Ketilidian orogen in South Greenland consists of an I-type granitoid batholith transected by four regional NE-SW-trending shear zones. Thebatholith was probably emplaced during subduction, from the south toward the Archaean craton in the north, in a sinistral transpressional system. A regional sediment sampling program covering5000km2shows a close connection between a gold-mineralized trend and one of the major shearzones within the epizonal facies of the batholith. The gold mineralization is not directly related to the major shear zones, but occurs in quartz-veined and silicified second-order structures. High-grade(up to 114 ppm Au over 6 m) low-tonnage mineralization is found within these second-order structures cutting both amphibolites and granitoids. The mineralization is characterized by negligible or small alteration halos. Gold is associated with various element combinations of enhanced As-Bi-W-Cu, which indicate that the mineralization is mesothermal in origin.

Jan 1, 1995

?NWCC has the highest number of Aboriginal students of any post secondary institution in BC and the region served includes 25 bands ? Chair of the Board of Governors is Irene Seguin (Hagwiloo K?am Saxwhl Giis) from Gitwinksihlkw ? FN council ? 39 First Nations Members * focus is to develop policy recommendations to increase student success rates

May 1, 2009

By R. Phillips, A. G. Doll, D. J. Barratt

"The Bond low energy impact (crushing) work index test is specified to be performed on rock specimens between 50 mm and 75 mm in effective diameter. NQ-diameter drill core, frequently used in mineral exploration programs does not meet that specification, it being 45 mm diameter or less.This paper reports the effect of performing the impact test on contiguous sections of HQ diameter and NQ diameter core, exploring the hypothesis that the contiguous intervals give equivalent results in spite of the core diameter difference."

Jan 1, 2012

By Al Hoffman

During the period May 15 ? 17, 2006 four fatalities occurred at #1 Waste Dump, at Teck Cominco?s Sullivan mine located at the city boundary of Kimberley, British Columbia, Canada. The fatalities occurred in the sump of a water monitoring station. The Chief Inspector of Mines and his staff immediately responded to the incident. The team worked collaboratively with the Teck Ltd. Trail Hazmat team, a consultant group from Rescan Ltd. and other Teck operation and technical staff. Sampling in and around the water monitoring station in the days following the fatalities showed that exposure to a depleted oxygen environment was the immediate cause of the fatalities. The sump located at the base of the shed was hydraulically connected to a French (coarse rock) drain, located at the toe of the covered waste dump. This presentation will briefly review the immediate cause of the accident, the investigation, a brief introduction to the work of the Sullivan Technical panel and the British Columbia government?s response to the incident and the recommendations of the Coroner?s inquest.

May 1, 2010

By M. K. Abel

"The Strathcona Mine is located in Levack Township on the North Range ofthe Sudbury Basin. The main orebody consists of pyrrhotite-pentlandite-chalcopyrite mineralization associated with an embayment of the footwall of the Sudbury Irruptive. A zone of massive chalcopyrite-cubanite-pentlandite mineralization occurs in a complex vein system in a series of mixed gneisses and breccias in the footwall. Vein widths vary from a few millimetres to 6 metres. In December 1979, this zone was estimated to contain 976,000 metric tonnes, with a grade of 9.31% Cu and 0.46% Ni. The vein system has a general strike of N 68°W at an angle of 60 degrees to the average strike of the footwall contact of the Irruptive. The dip of the vein system is 45 degrees sw. The strike and dip of individual veins in the system coincide with the directions that would result if a compressive stress had acted in a direction normal to the footwall of the Sudbury Irruptive, producing a conjugate set of fractures. The strike of the Irruptive at the Strathcona Mine is parallel to the long axis of the basin.IntroductionThe Strathcona Mine, owned and operated by Falconbridge Nickel Mines Limited, is located in Levack Township on the northwest rim of the Sudbury basin (Fig. I) . It is one of a group of nickel-copper sulphide ore deposits present along an 8.2-km section of the North Range of the Sudbury Irruptive. In the mines of the North Range, subunits of the Irruptive, going from hanging wall to footwall , include felsic norite, dark norite and dark norite breccia. The footwall complex at Strathcona includes the late granite breccia, which hosts a large proportion of the nickel-copper ores, and a compositionally variable group of brecciated and migmatized rocks, herein referred to as the feldspathic gneiss complex. It is within this latter group of rocks that the vein system of the Copper Zone occurs."

Jan 1, 1981

By A. S. H. Kabir, I-H. Jung, J. Su, S. Yue, M. Sanjari

The final mechanical properties of wrought magnesium alloys are mostly controlled by microstructure and crystallographic orientation or texture. In common magnesium alloys, grain coarsening occurs during annealing process and formation of undesirable basal texture cannot be changed markedly. The aim of this work is to investigate the effect of static precipitation on microstructure and texture evolution during annealing at 250 °C after warm rolling of Mg-Al-Sn alloy. Mg-3Al-3Sn (wt. %) alloy has been designed using thermodynamic modeling software, FactSageTM, based on forming target stable and incoherent Mg2Sn precipitate within the industrial deformation temperature range. Microstructures and precipitation were investigated by optical and scanning electron microscopes and macro-texture was measured by X-ray diffraction (XRD) techniques. It was found that static precipitates form in a large scale at the recrystallized grain boundaries and retards the grain growth during annealing. Slight weakening in basal texture was also observed during annealing.

Jan 1, 2014

By J. Bourgeault

Modem civilization is indebted to that most ancient of the skilled crafts - the art of stone working, as the one consistent means whereby the dim un-recorded past has conveyed to our modem schools of science volumns of facts, written in characters of imperishable stone. Although left, centuries ago, to ruin and decay, architectural examples of the ancient building crafts still remain to the glory of the old master-builders, whose accomplishments in that remote age continue to influence and inspire their modem successors. Present-day architects and builders will leave to posterity just as faithful a record of our modes of living and of the methods now adopted for protection, as if it had been made by written word; and our craftsmen have profited greatly, in meeting modem requirements, by taking advantage of the indurance and utility of stone. Stone in all ages and stages of the world's civilization and development has been the material chosen by the masterbuilder, the one material possessing qualities that render it most desirable in affecting the artistic ideals of each period. It perfects the science of architecture through its durability and thus renders possible the study of man's workmanship in stone throughout periods of civilization of which we have no specific written account. Other materials have been used for the construction of man's habitations, but none have withstood the test of time, nor have established the credit of designer and builder so well as stone. _All other materials fall into ruin and decay, leaving neither mark nor monument for the enlightenment of mankind.

Jan 1, 1925