Search Documents

By S. Lun Sin

In this study, the effect of silicon on the microstructure, mechanical properties and hot tearing susceptibility of permanent mould cast AZ91E magnesium alloy was investigated. Varying amounts of silicon (0.5, 1.0 and 1.5 wt.%) were added to AZ91E in the form of an Al-53 wt.% Si master alloy. The phase formation, grain size and solidification behavior of each alloy were characterized and related to their tensile properties and hot tearing susceptibility. The results showed that the addition of silicon resulted in the formation of Mg2Si particles. The presence of these particles led to an increase of the hardness, but was detrimental to the tensile strength and elongation of AZ91E. However, silicon significantly reduced the hot tearing susceptibility of AZ91E. This was attributed to the reduction of the grain size and the decreased freezing range of AZ91E, which contributed to improve the interdendritic feeding during the last stage of solidification.

Jan 1, 2011

By G. Gagnon

"HistoryMining of the Schefferville iron deposits began in 1954 on completion of the 357 mile railway linking the mines and the St-Lawrence river port of Sept-Iles. Apart from crushing, no treatment of these ores was required before smelting. In the late 1950's, testwork began at schefferville to develop a process for upgrading the extensive lower grade deposits containing 51% iron with 15% silica (natural analysis). Engineering for a six million ton per year beneficiation plant using cationic silica flotation and the A-C grate kiln Began in 1970 and the first pellets were produced in mid-1973.Production requirements and operating difficulties have restricted capacity to approximately 85% of design but on going improvements are being made continuously to attain design capacity.GeologyThe sedimentary ore bodies of the labrador trough occur in a belt 5 to 10 miles wide and 60 miles long and contain 51 individual deposits varying in size from 1 and 60 million tons. The ores are classified into three main color groups."

Jan 1, 1981

By George J. Simandl, Suzanne Paradis, Kirk D. Hancock, Jana Simandl

Traditional prospecting and boulder tracing are the two most important field techniques used in exploration for magnesite deposits hosted by sedimentary rocks. Consequently, success depends largely on the prospector's ability to identify magnesite. A density agent called sodium polytungstate (3Na2W04·9WOj'HPJ was successfully used to determine the presence of magnesite in sedimentary carbonate rocks of southeastern British Columbia. A rapid field method was developed and tested. This method permits discrimination between limy dolomites, dolomites, magnesite-bearing dolomites and magnesite-rich rocks.

Jan 1, 1993

By T. M. Siew

"This paper begins with a brief discussion of the geology of the Newfoundland Zinc Mine area. The results of groundwater studies and pumping tests are then presented. It was decided that groundwater in the mine could best be controlled by conventional sump pumping and grouting. The system is fully described, as well as plans for improvements on the method. LocationThe Newfoundland Zinc Mine is located in the Great Northern Peninsula of Newfoundland, six miles northeast of Daniel's Harbour. The mine is situated at an elevation of approximately 350 feet above sea level, 5 miles farther inland , west of the long range of mountains which rise abruptly with elevations of over 2,000 feet above sea level.GeologyThe ore deposits occur in lower Ordovician carbonate rocks that form part of the stable St. Lawrence platform, which is mainly composed of (1) the lower Cambrian Labrador group, (2) the upper Cambrian to lower Ordovician St. George group, (3) the disconformity overlying Middle Ordovician limestones and shales of the Table Head formation and, (4) two overlying klippen composed of Cambrian and lower Ordovician rocks.The ore deposit is a Mississippi Valley type of the Tennessee variety, having proven are reserves of 5.3 million tons averaging 9.70/0 zinc from eleven ore zones which exist in an area of 5.5 square miles.Among these ore zones, the L zone is the major underground mining area, and is by far the largest of the known deposits. It has proven are reserves of 3.4 million tons with 11.5% zinc; this underground development has been inprogress since 1974.Stratigraphically, the orebody, which occurs about 300 feet below the disconformities between the Table Head and St. George formations, is situated in the upper St. George formationof lower Ordovician age.The upper St. George formation of the L zone is divided into three main units (Fig . I) : the underlying lower limestone the middle grey dolomite pseudo breccia unit and the overlying siliceous dolomite unit. In this area of the mine, the beds of the St. George formation dip gently west to northwest to 10 to 15 degrees. The orebody, which is generally strata controlled with a southwesterly plunge and which has the form of thin, narrow, but elongate, en-echelon ore bed s, is contained in grey dolomite pseudo breccia. Its dimensions vary from 50 to 900 feet in width and 8 to 120 feet in thickness, and the over-alllength exceed s 6,000 feet.The surficial deposit of the area is a till comprising a heterogeneous mixture of sand, gravel, cobbles and boulders, with an average depth of 20 feet."

Jan 1, 1980

By Nigel J. Cook

"Detailed mineralogical examination of gold-bearing rocks, ores, concentrates and other samples should be considered an integral part of any study of a deposit for which exploitation is being planned. Adequate mineralogical study, although time consuming and often costly, can significantly improve understanding of the mineralization, can help to optimize the results of any metallurgical testing and can be of great value in case of potential trouble-shooting. The advantages and disadvantages of various examination techniques are discussed with reference to a number oj mineralogical studies oj Canadian gold-bearing samples.IntroductionVarious authors, notably Gasparrini (1983), Harris (1989) and Henley (1990), have stressed that mineralogical study of gold ores is critical to successful and efficient beneficiation. Only in cases where diagnostic cyanide leach testing is successful can detailed mineralogical examination be disregarded. Such examination of gold-bearing rocks and metallurgical products is all too often neglected because the methods involved are believed to be time-consuming, costly, and may carry a considerable degree of inaccuracy. Commonly, bulk metallurgical testing is, carried out without prior or concurrent mineralogical examination, causing the results of the testwork to be difficult to interpret, or in some cases, misleading. This, in turn, may lead to> significant delays to the project at the feasibility stage or mean that understanding of the sample is limited, preventing the introduction of prudent modifications at a later stage if problems arise. Mineralogical studies may guide the successful implementation of a metallurgical test program."

Jan 1, 1990

By T. G. Joseph

The strain softening relationship developed in part 1 is now applied to coal. Having determined the post-failure stress-strain curve for coal specimens, this information can then be used in a finite element program, such as Phase 2, to examine the post failure characteristics of coal pillars. Using example data, the strength of coal pillars of different width/height ratios are estimated and compared with well-known empirical pillar size-strength relationships. In addition, the post-failure stress-strain behaviour of a coal pillar is compared with an empirical relationship reported in the literature.

May 1, 2002

By E. B. Spice

"IntroductionExperience at Eldorado has been gained with a variety of mill feeds. That is, the actual mode of occurrence of the pitchblende varies to such an extent that gravity concentration has at times been decidedly unattractive and at others highly successful. Because of this, the type of ore necessary for economic recovery of pitchblende have become well known. Also, those types which do not lend themselves to gravity concentration have become familiar. In general, it may be said that when the pitchblende occurs free, to a large extent, from sulphides or arsenides of high specific gravity, and when the bulk of the pitchblende is localized rather than disseminated, excellent recoveries, high ratios of concentration, and good grades of concentrates , will result from proper gravity concentration. On the other hand, if the ore contains pitchblende intimately or otherwise mixed with large quantities of arsenides or sulphides, or if the pitchblende is finely disseminated, gravity concentration alone will yield high recoveries only at the expense of very low-grade concentrates and low ratios of concentration.According to Taggart, the ease with which gravity separation may be effected is determined by the value of the following ratio: []It is stated that when the ratio is above 1.75, gravity separation can be expected to be easy. Thus with pure U308 (S.G. over 9) and gangue consisting chiefly of siliceous material, the process can he expected to be entirely successful even when carried on at very fine sizes. Unfortunately, the term pitchblende covers a great diversity of material. Although some of the mineral occurs pure enough to have a specific gravity of about 7, the average is much lower than this and is probably well under 5. Some of the pitchblende particles have a specific gravity so low that gravity concentration fails completely. It may also be said that no degree of grinding will produce free pitchblende of sufficient density from such particles. This, then, represents the most important limitation to the application of gravity separation to pitchblende ores."

Jan 1, 1950

By F. S. Hoseinian, M. Irannajad, M. Safari

In this study, the effect of chemical interactions of materials used in ion flotation on the removal of Ni(II) ions from low concentration synthetic wastewater was studied. Sodium dodecyl sulfate (SDS) and ethylhexadecyldimethylammonium bromide (EHDABr) as collectors and methyl isobutyl carbonyl (MIBC) and Dowfroth250 as frothers were used. To investigate the effective parameters and interactions of them, 16 experiments including 6 level variables were performed by supporting DX7 software and on the bases of 2-level factorial method. In the first step, the tests were conducted in a Hallimond tube. The result showed that collector of SDS and frother of Dowfroth 250 had appropriate interaction with each other at pH = 3. In the second step, optimal results from the first step were evaluated in a mechanical flotation cell. The removal of Ni(II) ions increased by increasing the time of flotation and they have a direct relation with the water removal. The kinetics study shows that the order and the rate of removal of the reaction do not follow any of the zero-order, first-order and second-order equations. The flotation rate curve on the removal of Ni(II) ions will divide the separation process to two stages, a fast flotation rate at the first stage and a slow flotation rate at the second stage. Ni(II) ions removal was obtained 88% at the best condition.This study showed that the use of ion flotation was a very effective method for Ni(II) ion removal from industrial wastewaters.

Jan 1, 2016

By Robert B. Parsons

"The pendulum in Ottawa has swung dramatically from fiscal policy to monetary policy over the last several years. International trends indicate that the pendulum has to start its swing the other way, if Canada's mining industry is to maintain its preeminent position in the global mining arena. This article, which is based on a paper presented by the author at the 37th Annual Meeting of the Newfoundland Branch of CIM, identifies these trends and how they could interact with Canadian policy.IntroductionThe title of this paper is not a very imaginative or catchy one, but it states the topic quite succinctly, if not tersely. This paper looks into a crystal ball to see what might be in store for mine financing over the balance of the current decade.In the event that the reader feels some trepidation about the prospect that such a paper could seek to be the definitive work on the subject, it should be made clear at the outset that this is not the case. The author is, after all, not an economist, a scholar, a financial analyst, or a soothsayer, but is rather a simple accountant who has been closely involved with the mining industry, and the financing thereof, for some twenty years.The paper recognizes that, while a mine may be born when production begins, the mine is conceived when exploration starts. As this act of conception is obviously an essential part of mining, the financing of exploration is also covered in this paper. To attain a focus, this paper approaches the topic of mine financing in the nineties as follows: first, the major emerging forces in the industry are identified: and, second, the implications of each of these forces on financing are considered."

Jan 1, 1991

By E. G. Parker

"Sherritt's zinc pressure leaching process converts zinc sulphide concentrates directly to zinc sulphate solutions and elemental sulphur. Thus, one pressure process step replaces both the roasting and leaching operations of the conventional roast-leach route. In addition, high single-pass extractions eliminate the need for residue treatments to recover unleached zinc. Because pressure leaching produces elemental sulphur, rather than sulphur dioxide, acid plants and smoke stacks are not required, and air pollution control and work-place hygiene are greatly improved. .In 1977, Cominco Ltd. and Sherritt Gordon Mines Limited jointly operated a three-tonne-per-day pilot plant to demonstrate pressure oxidative leaching of Sullivan zinc concentrate and the subsequent separation of elemental sulphur. The process consisted of regrinding the concentrate, continuous leaching at 150°C at elevated oxygen pressures in a four compartment autoclave and the subsequent recovery of elemental sulphur, either in the molten liquid form from a decantation autoclave or as a flotation concentrate. Of the zinc contained in the concentrate, 97% was extracted in 90 minutes, and 96% of the sulphur was converted to the elemental form.Following the successful pilot campaign, Cominco began building the world's first commercial zinc pressure leaching plant. This plant, which was in operation by late 1980, will eventually treat about 25% of Cominco's planned zinc capacity of270,000 tonnes per year.This paper describes the general process principles, the results obtained from the pilot plant and the integration of the process into Cominco's operations at Trail. The application of pressure leaching to a ""grass-roots"" plant is also discussed, and compared with conventional roast-leaching."

Jan 1, 1981

By Erica J. Wanless, Ghislain Bournival, Seher Ata, Jose Hamilton Tavares

In froth flotation valuable particles are captured by bubbles and transferred to a froth layer where bubbles are in close proximity. Bubble coalescence frequently occurs in flotation, especially in the froth layer. The coalescence of two bubbles causes a release of energy, which may expel particles from the bubble surface. A series of experiments were carried out to determine the effect of bubble interfacial properties on the detachment of particles upon the coalescence of capillary-held bubbles of 2 mm in size. The interfacial properties of the bubbles were changed by the addition of low molecular weight alcohols, namely 1-pentanol or methyl isobutyl carbinol (MIBC). Using esterified glass particles (? = 43 °) with a 10 % and 90 % cumulative passing diameter of 47.2 and 92.5 µm, respectively, as model particles, it was found a certain concentration of frother, different for each additive, is needed in order to observe a reduction in the detachment of particles. In the presence of frother, the detachment was evaluated at approximately 65 % which was a considerable reduction in the detachment compared with the value of approximately 85 % found in the absence of frother. Frother molecules changed the properties of the airwater interface. Upon the coalescence of two bubbles, the release of energy caused the merged bubble to oscillate; effectively resulting in the detachment of particles. The addition of frothing agents augmented the elasticity of the bubbles, which appeared to be related to the detachment of particles. Whereas frothing agents are generally used to prevent bubble coalescence and stabilise the froth phase, only transient stability is imparted. The results suggested that an additional role of frothers in flotation is to decrease the detachment of particles from bubble surfaces. The type and concentration of frother can be strategically selected to improve metallurgical recovery as an economic incentive.

Jan 1, 2016

By Changmiao Liu, Dong Dong

"Magnesite is a major mineral resource in China, whose output and export are massive and quite important to the world. Flotation performances of eight anionic collectors on magnesite were studied to find the proper ones. Micro-flotation results indicated that collectors of HOl, SDBS and AEP had outstanding flotation performances on magnesite, with the recovery ratio all reaching above 90% in a wide range of alkaline pulp. Solution chemistry calculation, Zeta potential and FTIR measurements were employed to reveal the interaction mechanism between anionic collectors and magnesite surfaces. Solution chemistry analysis indicated that the main active components of HOl, SDBS and AEP were anions and association complex anions in alkaline pulp. Magnesite surface was negatively charged in the alkaline pulp. The active sites on magnesite surface were mainly the components of MgOH-, Mg (OH)2, and MgCO3 when the pulp pH was over 8. Anionic components of HOl, SDBS and AEP reacted with Mg in magnesite surface to make the insoluble anionic salts. And the chemical adsorption was confirmed by the FTIR measurement evidences.INTRODUCTIONAs an important industrial mineral, magnesite has been widely applied in metallurgy, building materials, chemical industry, agro-pasturage and other fields (Hu et al., 2006). It is a major mineral resource in China with abundant reserves. Its output and export are massive and quite important to the world. Liaoning province is rich in magnesite, whose reserves and production both come first in China. So far the proven reserves have reached 2.91 billion tons, accounting for more than 90% of total reserves in China, and more than 25% in the world (Li et al., 2012).Magnesite ores in Liaoning province mainly contain crystalline magnesite, and the gangue minerals of quartz, dolomite, talc, tremolite, chlorite and carbonaceous materials. Some ores also contain a little pyrite, chalcopyrite, hematite and apatite. Most of the ores must be preprocessed to separate the useful parts from the large amount of gangue minerals, so that their value and industrial application can be enlarged and promoted.Flotation is commonly used to process the magnesite ores, and the conventional flotation methods include anionic and cationic flotation. In the former, gangue minerals of silicates were separated by using amine type cationic collectors. After the impurity minerals were removed, high qualified magnesite concentration could be gained. For the cationic flotation method, it had some drawbacks of lower recovery ratio and poor performance in the lower temperature pulp (Li et al., 1995)."

Jan 1, 2016

By Robert White

?Introduction of BMS?Paste fill generalities?Development through paste?Development through rock fill?Conclusion ?Brunswick mine is operated by Xstrata. The mine has been in operation since 1964 and produces around 10 000 tons per day of ore containing (in order) zinc, lead and silver? The ore body consists of close to ten sub-parallel massive sulfide lenses. The length of the ore body is 1200 m with a width of up to 200 m. From the surface, the ore body extends to a depth to 1200m ?There is 100 km of active drifts for a total 400 km ?The mine is divided by 7 levels and 23 actives sub levels

Feb 1, 2008

By Jean-Luc Beaudoin

"In addition to the actual energy consumed, billing is dependent on the peak load and the power factor. The lower the power factor goes, the higher will be the penalty the consumer pays. The principles of a power factor regulator, the two ways of improving the power factor and methods for calculating the capacitor values required will be described.The rate structure of the utility company is founded on three cornerstones: the energy consumed during a given period of time and two penalties imposed when the power factor is low or the power demand is high. Even though the normal consumption of a customer might be 10 kW, with a peak demand of 20 kW only once a month, the wiring and associated equipment at the input to the customer's plant will have to accommodate this peak demand. The power company has no means of forecasting these demands and cannot therefore provide the additional equipment necessary. So it exacts a penalty, and the customer must take all possible steps to avoid these peak power demands. This can be accomplished by using an automatic peak load regulator which will selectively disconnect the loads which are not essential in the operation of a plant .The principles of such a controller will be described.Principles of power factor regulatorsThe operating principles of a power factor regulator will now be described. It might be asked why the power factor of an electrical installation in a mine, or a factory, should be corrected at all, but there is a simple answer. In addition to the actual energy consumed, the billing is dependent on the peak load and the power factor. The lower the power factor goes, the higher will be the penalty the consumer pays."

Jan 1, 1982

By BARRY BANNATYNE

Non-swelling bentonite has been quarried in Manitoba by Pembina Mountain Clays Limited since 1941. It occurs in several thin layers near the base of the Pembina Member of the Upper Cretaceous Vermilion River Formation, and is quarried from the narrow outcrop belt along the slope of the Manitoba Escarpment. It is marketed both as natural and activated bentonite for a variety of specialized uses. Percolation of acidic water through bentonite has produced a naturally activated bentonite with good absorbent properties; these properties are enhanced by treatment with sulphuric acid to produce an activated bentonitefor decolourizing petroleum and vegetable oil.

Jan 1, 1984

By Marek Mika

This Paper has been prepared to be presented at the 23rd World Mining Congress & Expo ? Montreal 2013. It presents the idea how to carry out the shaft sinking operation, going through highly water-bearing and very weak rock strata, giving as an example one specific shaft sinking project which is being executed for one of the Polish collieries by our Shaft Sinking Company Content 1. Introduction. 2. Hydrogeological conditions within the area of the shaft. 2.1. Hydrogeological conditions assumed at the stage of designing. 2.2. Hydrogeological conditions encountered in the course of sinking. 3. Designed shaft lining. 4. Procedures for the shaft sinking. 4.1. Designed procedures of the shaft sinking. 4.2. Procedures for preservation and strengthening of the shaft lining and the surrounding rock strata. 5. Technological guidelines for proceeding with the shaft sinking ? selection of special methods. 6. Options for mechanization of work for the selected method. 7. Conclusions.

Aug 1, 2013

By Sina Mostaghel, M. Guo, E. Klaffenbach

The current paper is focused on evaluating the behavior of copper in a copper production slag and the assessment of metal recovery possibilities. For this reason, thermodynamic calculations were carried out to determine the influence of parameters such as slag composition, temperature and oxygen partial pressure on recovery of non-ferrous elements. It was found that the formation of a solid face centered cubic (fcc) phase, mainly consisting of iron, limits the extent of reduction that can be achieved for an industrial process. However, it could be discovered that solubility of iron in the Cu-rich liquid alloy strongly depends on presence of other elements, particularly arsenic. As part of the results of this study, the solubility of Cu in the slag at onset of fcc phase formation is presented as function of temperature, oxygen partial pressure and concentration of MgO and CaO. It was concluded that lower temperature (1200°C) and higher CaO addition (16 mass-% in this study), would result in the highest achievable copper recovery from slag. INTRODUCTION Copper slag is produced as a by-product of the copper production process. The slag is still containing a high amount of copper and other valuable metals. This demands further treatment of the slag as a secondary source of metals. In addition, the physical/mechanical properties of slag allow its use in several applications such as hydraulic engineering, civil engineering, as an abrasive and many more. These applications help reducing the use of natural resources like rock and sand. By decreasing the content of heavy metals such as Cu, Pb, Zn and As in the slag, its application in abovementioned fields becomes more attractive as the probability of releasing these elements to the environment is further reduced. To develop a pyrometallurgical slag reduction process, it is necessary to understand what describes the end point of the reduction. This point is expected at maximum copper recovery without facing operational challenges. Existing literature provide some information on the effect of different parameters such as temperature or concentration of different slag formers, on solubility of copper and heavy metals in different phases. However, due to complexity of industrial slags, equilibrium experiments and accurate thermodynamic modelling are essential to be able to reliably predict the behavior of different elements in the system and determine the end-point of reduction.

Jan 1, 2019

By R. A. Walker, G. Scheltgen, T. Javorsky, G. Blackwell

"Recent engineering advances in open pit rock mechanics have resulted in improved pit wall slope design and improved operating procedures in the event of a major wall instability. At the other end of the spectrum, on the scale of single bench failures, considerable discretion is left to the mine operators as to how potential problems are handled. The usual alternatives are either to operate with caution beneath potential hazards, or try to bring the unstable rock down. In specific cases it may be advantageous to attempt to stabilize rock structures for reasons of access and operating safety.A t the Brenda Mines open pit a prominent structure on the north wall had caused recurring bench-scale wedge failures when exposed on each mining level. In spite of operating precautions a shovel was hit by a rockfall causing significant damage. The first section of this paper describes the investigative, design, and stabilization methods which permitted subsequent mining beneath the structure to proceed without incident. Emphasis is placed on the personnel and equipment resources available at the mine site which were used to minimize costs and which would be available at most operating mines.The second section describes an ongoing research project that utilizes radio telemetry to transmit slope monitoring data. As part of this project the wedge structure was instrumented so that it could be continuously monitored with the aid of a computer. The application demonstrated the potential of 'micro- chip' technology to remote data collection and processing as related to rock structure monitoring, slope stability and safety."

Jan 1, 1989

By J. P. Weiler

The increasing use of high-pressure die-cast magnesium alloys in the automobile industry requires a better understanding of the mechanical properties, the microstructure, and particularly, the relationship between these two. The goal of this study is to first understand the microstructural features which control the mechanical properties observed from an AM6OB magnesium alloy, and second, to be able to predict the local mechanical properties based on microstructural features encountered in different areas of the die-cast component. The two main tools used in this study are spherical indentation testing, used on local areas of the die-cast magnesium alloy AM6OB to detect changes in microstructure and mechanical properties, and X-ray tomography, used to non-destructively investigate the internal porosity in a sample. The results from these tests are then used to predict the local mechanical properties such as the yield stress, the strain-hardening characteristics, and the fracture properties of the AM6OB component.

Jan 1, 2006

By Garth D. Kirkham

The Problem The Don deposit is a series of two sub-vertical zones that pose a number of challenges with respect to modeling and interpolation. The first challenge is that, based on data and observations, the mineralization and, more importantly, the grade is layered or banded and is stratigraphically controlled. The second challenge is that, due to the undulations of the deposit and extreme changes in dip, using a standard oriented ellipse to guide the estimation process is not appropriate and does not result in an estimate that is representative on a local scale. In order to solve this problem an adapted methodology of relative elevation modelling, has been devised to effectively model and estimate deposits faced with these challenges. Relative Elevation Designed for bedded seam and gridded surface With variable dip and vertical grade variability

May 1, 2013