Search Documents

By Shek N. Lau, Nicola Samman

"Enclosed gear cases on board heavy mining equipment have traditionally been lubricated with regular heavy duty gear oils. However, equipment manufacturers, have recommended the use of an ISO-1000 gear oil for this application to ensure adequate lubricant film strength, especially at the higher end of the working temperature range. The majority of these ISO-1000 gear oils are based either on residual/asphaltic oil or synthetics, primarily higher viscosity polyalphaolefins. Although the performance of these lubricants has been satisfactory, they suffered other shortcomings that equipment users have lived with over the years.The major requirement at the user’s mine was to provide lubrication for the shovel Hoist gear case. Within such a gear case design, the gears and the roller bearings, that have different lubrication requirements, are lubricated with the same lubricant. Several lubricants were used, light gear oils as well as the recommended ISO-1000 heavy gear oils. On the one hand, the lighter oils performed adequately for the lubrication of the bearings that formed part of the enclosed gear system. These lighter oils did not perform as well for the lubrication of the gears due to their lower viscosities, resulting in shorter gear servicelives.On the other hand, the ISO-1000 gear oils performed well for the lubrication of the gears, but were too viscous to creep into the bearing elements to lubricate them adequately, especially during the cold northern Canadian winters. This resulted in catastrophic bearing failures and secondary damages to the gears.The challenge, then, was to formulate a lubricant which met the 1000 cSt at 40°C viscosity requirement as stipulated by the equipment manufacturer, while satisfactorily lubricating the bearings at the full working temperature range. This was achieved by the development of a semi-fluid grease lubricant, which has proven in field trials to give adequate performance in this application for the lubrication of both the bearings and gears down to -40°C.This product met the equipment manufacturer’s performance criteria and resolved, to a large extent, leakage of the lubricant through seals experienced with the use of conventional and synthetic gear oils.Although the main performance criteria of the fluid was its capability to lubricate the “Hoist” gear case, it was also used during the field trial in other gear cases on board the shovel to test its full capabilities.This unusual alternative lubricant was field tested and evaluated for more than two years. Based on this assessment, the product was reformulated to improve its fluidity, slumpability and the settling of debris/wear metals to the bottom of the gear cases. This reformulated softer grade, a semi-fluid grease, has been performing satisfactorily for more than eight months and is still undergoing longer term assessment."

Jan 1, 1996

By C. Sideco

"Concentrate drying at the Sullivan Concentrator goes back to 1937 when the original coal-fired dryer was put into operation. This was a second hand 8' dia. x 56' long Struthers-Wells rotary dryer that came from the phosphate plant in Warfield, B.C.In 1962, replacement of the old dryer was seriously considered. The shell and the auxiliary drive mechanism were badly worn and needed replacing. In April 1963, the new 8' dia. x 65' long fuel oil-fired Struthers-Wells dryer went in operation at an installed cost of $174,000.In 1965, it was apparent that a major rebuilding of the dust collecting system would have to be done. A study was carried out and a Ducon Dynamic Gas Scrubber was installed. The system went in operation in November 1966 and has fully met expectations.In the same year, the zinc dryer was converted from fuel oil to natural gas. The conversion has resulted in savings in fuel cost of 12 to 15%.Frame No. 1Zinc Dryer PerformanceDryer Make - Struthers-WellsDryer Size 3/4 8' dia. x 65' long Drum Drive - 100 HPSpeed of Rotation - 5 RPMFeed Rate - 50-65 TPHFeed Moisture - 10-12%Discharge Moisture - 4-6%Dryer Inlet Temperature - 1600-1800°F Dryer Outlet Temperature - 200-250°F Stack Gas Volume - 25,000-40,000 CFNDust Collecting Efficiency - 99.75-99.98% Duet Loss in Stack - 50-300 lbs./day"

Jan 1, 1972

By Douglas A. Karvonen

"Competition in the world potash market has increased significantly since the late 1970s. The failure of consumption to grow at expected levels has led to industry over-capacity, a situation which is likely to persist at least until 1990. Individual Saskatchewan producers and their offshore marketing company, Canpotex, have responded to this challenge by increasing mining efficiency, developing more cost-effective and reliable transportation systems and establishing innovative financing and market development programs tailored to customers' special needs. Investment in warehouse facilities to serve U.S. customers and exploration of opportunities for intermodal distribution through the Great Lakes and the Mississippi River system have maintained individual producers' position in the highly competitive domestic market.Export sales through Canpotex have been bolstered by utilization of CIDA funds, Exp ort Development Corporation financing guarantees and other innovative payment plans which enable heavily indebted developing countries to maintain the import levels which are necessary for their agricultural development.IntroductionPotash is the general term applied to various potassium salts both natural occurring and commercially derived. The most common of the commercial product s are potassium chloride, potassium sulphate and potassium magnesium sulphate. The potassium content of potash is measured in units of K20 equivalent. The common grades of potassium chloride produced for agriculture average at least 60 0/0 K20 compared with approximately 50% Kp for potassium sulphate and 22% for potassium magnesium sulphate."

Jan 1, 1985

By J. Gray, J. Peck

As the turn of the century approaches, traditional open pit mining methodologies and processes are being modified through the introduction and use of new technologies. As in other industries, the personal computer is dramatically changing the traditionally conservative mining industry by allowing mines of varying size and capacity to increase their productivity and efficiency through the use of easy to use, office software. Computer-based monitoring and control systems are also being used more frequently to measure and optimize, in real-time, the performances of operating equipment. When communicated to an end-user, this information can provide accurate and timely answers to questions of how much, where, when, and by whom. This capability forms the foundation of a more comprehensive, proactive management and planning facility where, ultimately, information acquired from the producing equipment will be used to optimize and control machine and human activities. As these technologies mature and become essential tools in a mine, they will eventually serve as the basis for more robotic and autonomous mining operations.

Jan 1, 1999

By P. K. Chatterjee

"The operations of a large-scale open-cut mine are simulated to produce a user-oriented interactive digital model. SIMULA is chosen as the programming language and a sophisticated data base system is designed to consider the complex information network of large mines. The main features of the program are the mine planning and mine evaluation modules. These modules are responsible for the computation of truck-shovel performance and other equipment details in a mine. Stochastic methods are employed to generate event times. The use of a Data Base Management System and the data base provide an efficient method of information storage and retrieval. Truck allocation techniques have been examined in detail and comparisons between random dispatching and conventional methods are made. The model is intended for mine operators and engineers and the program is well structured and very readable. It is hoped that these features will make the model readily acceptable.IntroductionThe Department of Mining and Metallurgical Engineering at the University of Queensland has been conducting research into computer simulation methods in mining since 1972. The research has been mainly applied to actual operations, with both open-cut and underground mining being equally emphasized. The results of the research to date have not only strengthened the methodology of the approach to complex mining problems, but have also increased confidence in the use of modelling and computer simulation technique s in mining.The model described in this paper translates a complex LHD situation into a user-oriented interactive digital model using SIMULA. The present methods of evaluating truck dispatching and trolley assist are tedious and laborious. This model provide s the engineer with readily acceptable means of rapidly assessing the relative merits of these techniques in a large-scale open-pit operation. Poor utilization figures in many current operations (for example, 40% for trucks, 70% for shovels) are of serious concern to mine officials and computer-controlled dynamic truck dispatching systems have been considered by some of these mines to improve equipment utilization ."

Jan 1, 1981

By N. Bakhshizadeh

In this investigation, the aging effect on creep behavior of A12024-10%SiC composite fabricated by powder metallurgy was studied. P/M bars were manufactured by hot powder extrusion method at 450°C with a ratio of 16 to 1. Creep specimens were over-aged at 187 ºC for 43 h. It was found that almost full density composite with relatively homogenous distribution of reinforcing particles throughout the aluminum alloy matrix could be attained by direct powder extrusion process. Creep tests were conducted at temperatures from 275 to 325°C under stresses from 25 to 60 MPa. The analysis of the creep mechanism determined that dislocation glide was the predominant mechanism of plastic deformation. The activation energy of the creep process was found to be higher than that of lattice self-diffusion in pure aluminum.

Jan 1, 2007

The Shortage of Mining and Metallurgical Engineers I N many parts of the Western World attention has recently been drawn to the acute shortage of mining and metallurgical engineers produced by the universities. Naturally, the reasons for this shortage have been discussed, and various remedies for it have been proposed. In this paper, I want to examine some of them. It is now fairly generally ac-cepted among mining men that the easy attractions of modern urban life have left the career of mining in the metaphorical as well as in the literal backwoods. The industry finds it increasingly difficult to recruit adventurous and intelligent young men; for such men now seek their intellectual, if not physical, adventure in more glamorous occupations from a safe social base in suburbia. The salaries, opportunities and security offered by the mining industry do not complete effectively with the rewards offered by other industries and by commerce, taking into account the social disadvantages of a mining life. The excitement and other non-material attractions of mining

Jan 1, 1965

By I. S. Thompson

A program of geochemical till prospecting, carried out by Derry, Michener & Booth in 1974, was instrumental in t~ e discovery of a copper deposit in Currie Township, Ontario, beneath thick lacustrine deposits of the Abitibi Clay Belt. The prospecting system involved the continuous collection of glacial sands and gravels beneath the clays, using a track-mounted, dual-tube rotary drill, and the separation and geochemical analysis of the heavy mineral content for Cu, Zn, Pb, Ag and Au. In one of 22 holes drilled down-ice from nine Canadian Nickel airborne EM conductors, fragments of chalcopyrite-bearing graphitic argillite, assaying 12% Cu, were recovered from a 14-foot gravel section beneath 83 feet of clay. Ultimately, mineralization was identified in 10 of 11 additional holes drilled up to 3,000 feet down-ice from the Currie deposit. The glacial fan, when compared to the 1,200- by 165-ft area of the subcropping mineralization, is at least 20 times the area of the deposit and is the result of glacio-fluvial reworking of the mineralized ground moraine. The Currie deposit is contained within a Keewatin succession of graphitic argillite, dacite tuff and graywacke, which is intruded by dacite and feldspar porphyry sills and dykes and truncated by a Keweenawan diabase dyke. Grade and thickness of the mineralization, which lies chiefly within the argillite, is related to felsic intrusives and hydrothermal alteration, and to fold hinges.

Jan 1, 1979

By M. A. T. Cocquerel, J. G. Eacott

"Simulation techniques may be used to optimize existing processes and plant operations, and in plant design at the engineering study stage of a project . This paper describes the latter application, using a computer, to optimize the concentrate stockpile requirements of a modern copper smelter.A large open-pit mining operation is envisaged and it is assumed that copper concentrate is smelted in two flash furnaces. The proposed mining plan gives rise to metaffurgical considerations in smelting which dictate that concentrate blending is carried out in the early years of operation in order to eliminate wide variations in the grade of concentrate charged to the furnaces . Stockpiling facilities are therefore necessary for blending purposes and also to provide a strategic reserve of concentrate to ensure continuity of concentrator and smelting operations.The objective of the study is to determine the optimum size of concentrate stockpile required to take account of both metaffurgical and strategic considerations. Two separate simulation models are developed to achieve this objective. The first model is used to determine the minimum size of stockpile necessary for blending purposes to smooth out variations in concentrate grade between 15 - 60% Cu, with associated 34 6% Fe, respectively, and ensure that the concentrate fed to the furnaces does not faff below 12% Fe, which is considered a minimum for good smeltability.The second simulation model covers a projected three-year operating period and indicates the maximum size of stockpile which is likely to develop during scheduled and unscheduled shutdown periods in the concentrator and smelter.Covered storage volume and conveying facilities for the optimum size of concentrate stockpile can be designed based on the results generated by the simulation models."

Jan 1, 1980

By A. Zrimsek, G. Vingas, R. Wolke

IN 1952, prompted by the great demand of the Canadian drilling and foundry industries for sodium bentonite, the Geological Department of Magnet Cove Barium Corporation, Limited began an extensive search for bentonite deposits throughout western Canada. Their efforts were rewarded in 1958, when substantial deposits of high quality material were found approximately 100 miles southeast of Edmonton, Alberta. The bentonite material, a part of the Edmonton formation in the Upper Cretaceous, is located approximately nine miles south of the town of Rosalind. The land where the bentonite lies has in places .been eroded by stream and glacial action to form a wide gully, convenient for strip mining methods (see Figure 1). The bentonite bed is almost flat-lying, dipping to the southwest at approximately 12 feet per mile. The main bed is 8 to. 10 feet thick and is covered with 15 to 25 feet of overburden. Before stripping, the area is drilled and sampled to evaluate the quantity and quality of the bentonite.

Jan 1, 1962

By J. M. Beeckmans, S. G. Butcher, M. Goransson

"The counter-current fluidized cascade is a novel and potentially efficient pneumatic gravity separation device. Data are presented on over 150 runs of cleaning Alberta thermal coals, covering several size ranges. The coarser sizes of coal were processed in admixture with a fluidizing medium consisting of 0.5-by 0.1-mm hematite (or magnetite) and limestone particles. The partition curves for coal particles larger than about 3 mm, mixed with fluidizing medium, showed that the sharpness of separation achievable with the cascade approaches that of wet heavy medium processes, whereas with particles in the size range of 3 by 0.6 mm the sharpness of separation was comparable to that of a Baum jig. Useful cleaning was also achieved with particles smaller than 0.6 mm , Throughput rates of up to 11 tonnes per metre width of cascade per hour were achieved, with no indication of a deterioration in performance.IntroductionPneumatic coal beneficiation has steadily lost ground vis-a-vis hydraulic beneficiation during the past quarter century, primarily because of the sharper separations achievable with the latter methods. Nevertheless, there are certain inherent advantages of pneumatic separation methods which would give them an advantage in the market place were it possible to increase their efficiency to be technically competitive with those of hydraulic processes. These advantages are a dry product, resulting in a higher calorific value per ton, and avoidance of the problems associated with treatment and storage of process waste waters. Also, although it may be necessary to dry the raw coal prior to pneumatic processing, the dry rejects produced constitute an ideal fuel for a fluidized-bed combustor, which could provide heat both for drying the coal and for other purposes."

Jan 1, 1982

By John H. Schloen

"The object of this paper is to review electrolytic copper refining as it was in 1954(1), as it is now in 1984, and to comment on the many improvements which have been made in the last thirty years.In 1954, and even in 1984, the ASTM specification B 115 for cathode copper was 99.90% minimum copper plus silver content and 100% minimum electrical conductivity, IACS standard. However, to meet competition and to satisfy the requirements of the fabricators and the electrical industry, the electrolytic refinery must supply a product of 99.95% to 99.96% minimum copper content, and 101fJlo minimum electrical conductivity.The range of cathode impurities reported by 20 major copper refineries in 1954 are given in Table I.The much more rigid British Specification, DD 78, for high-purity cathode copper, specifies individual elements, as well as groups of elements, as shown in Table 2.The Svenska test has been replaced by a similar procedure which uses 2.r mm diameter wire. The ISO test is the one listed in the DD 78 specification. In Table 3, corresponding values for the Svenska and ISO test s are given for various wire bar coppers."

Jan 1, 1986

By D. Racicot, T. Hanel, E. H. Chown

Over thirty plutons in the Chibougamau-Desmaraisville belt were examined briefly in the field and sampled, in addition to the few masses that have been studied in detail. The survey indicates that the intrusions may be conveniently grouped in four main categories, based on their time of intrusion. These are; remobilized basement domes, pre-kinematic intrusions, syn-kinematic intrusions and postkinematic intrusions. Basement domes, as exemplified by the Lappa rent Massif, are composed of migmatized tonalite-diorite gneiss that has undergone at least two periods of mafic dyke intrusion and at least three major deformational periods. The rise of the basement domes was accompanied by extensive mylonitization and the intrusion of syn-tectonic plutons. Pre-kinematic plutons, such the Chibougamau pluton, are diori te-tonalite in composition, and were intruded into the supracrustal pile and partly eroded before the main deformation of the belt. Syn-kinematic plutons occur principally as marginal intrusions bordering the belt (Barlow), or as discrete intrusions along structural highs (La Dauversiere), and are either hornblende monzodiorite or tonalite in composition. Post-kinematic plutons, such as Muscocho, are principally granodiorite and often porphyritic intrusions locally deforming the enclosing rocks. The close relationship between mineralization and high-level intrusions such as the pre-kinematic and some of the post-kinematic plutons is discussed.

Jan 1, 1984

By J. E. Rowland

NIOCALITE is a new mineral species which has been identified in rock from the Oka district, Quebec. It occurs as prismatic crystals up to l 0 mm. in length and I mm. in width, in coarse, white, crystalline calcite with associated apatite, diopside, biotite, pyrochlore, and niobian perovskite. The crystals of niocalite are light yellow in col-our and have a vitreous lustre. The optical properties of niocalite (I) are as follows: Biaxial negative -2V = 56° a = 1.700, [ ] = 1.730 Birefringence y -a = 0.030 Optic orientation: X = b, Z/\c 12°, Y , /\a = 32° The specific gravity is 3.32 and the hardness is approximately 6 (Mohs scale). A detailed analysis performed on 2.4 gm. of hand-picked material reveals that niocalite is essentially a calcium niobium silicate. Table I gives the result of the analysis. Crystals of niocalite, apparently suitable for X-ray diffraction work, were selected, and single crystal photographs were obtained using both Weissenberg and Precession cameras. Initial difficulties were encountered in interpreting these films, and in correlating the crystal data with the optical data. The in-consistencies were explained by the fact that every grain examined was twinned to some extent.

Jan 1, 1957

By G. J. Govett

THE RESERVES of industrial minerals of the Western Plains are probably several times more valunable than all the known deposits of metallic minerals of the Canadian Shield, though sharing little of the latter's popular appeal. Because of comparatively low value per unit weight or volume, an adequate and accessible supply of industrial minerals is essential for the full development of any territory; assessment of the value of deposits should consider fully the proximity to cheap transportation, and existing and potential markets. Production statistics of industrial minerals are probably a more reliable guide to economic development than, for example, those of petroleum, and the relative importance of industrial minerals increases with growth of the population. The development of a high-volume natural deposit such as petroleum naturally favours an increase in population, and thus industrial minerals form an integral part of an expanding industrial economy. This situation is clearly demonstrated by the relationsl1ips of industrial minerals production, petroleum production, and population growth, in Alberta (Figure 1).

Jan 1, 1959

By B. K. Mishra, P. Patnaik, B. C. Tripathy, I. N. Bhattacharya

Cobalt is an essential metal considering its numerous industrial applications. The demand for the metal is increasing due to its wide range of use in, for example, rechargeable batteries and as an alloying element in super alloys. Cost effective production of Co is critical. Electrowinning from aqueous sulphate solutions is the preferred technology available for the production of Co. Attempts are being made to produce uniform, smooth and bright deposits of cobalt metal. Use of organic additives in the electrolytic bath improves current efficiency and deposit morphology of the metal. We investigated the effect of quaternary amines TEABr, TPABr and TBABr during cobalt electrowinning from aqueous sulphate solutions. Among the additives studied, TEABr yielded the best results. Smooth and bright deposits of cobalt were obtained at low concentration of TEABr (10 mg/L) maintaining a very high current efficiency of 99.6%. X-ray crystallography indicated that (100) is the most preferred plane of crystal growth.

Jan 1, 2014

By Jorge Lema Patino

"The purpose of this paper is to determine the best techno-economic alternative for the treatment of tin ores, when comparing the various mining and metallurgical methods of preconcentration, concentration, volatilization (fuming) and up to the final stage of selling to the smelter. The study of the influence of the different parameters of cost, recovery and quoted prices has motivated the paper, which aims at determining the best process of ore treatment in terms of its techno-economic feasibility.Method of WorkOn the basis of head grades of 0.5, 0.75 and 1.0% tin, the following alternative methods of treatment are possible:1. Mining-Concentration-Smelting.2. Mining-Preconcentration-Fuming-Smelting.3. Mining-Concentration-Separation, with direct smelting and fuming/smelting of the two fractions produced.The calculations were carried out on the basis of existing information and publications concerning the various experimental recoveries in the operating mills of COMIBOL. In the case of concentrates containing less than 10% or more than 40% tin, extrapolation was required.The final grade of the tin concentrates and the gross weight of the concentrate were calculated on the basis of the estimated recovery curves. The costs of the preconcentration and the concentration stage s were determined per gross metric ton of material treated.The calculation of the cost of the smelting stage is similar for all the alternatives, the royalties and smelting charge varying with the grade of the final concentrate. In the fuming stage, a uniform recovery of 90% was taken in all cases so as to obtain a final concentrate grade of 65% tin, regardless of the head grade of the feed material.For the separation stage, the following considerations apply:a) Separation can be carried out by gravity separation or flotation methods.b) The cost of separation varies depending on the system used.c) The distribution of tin in the two fractions is 100% at this stage. In other words, there is no loss of tin during separation."

Jan 1, 1982

By Leonard A. Wolff

"The 1980sfor the mining industry can be characterized as the survival of the fittest. High interest rates, low commodity prices, foreign subsidized competition and decreasing ore grades have contributed to a streamlining of the domestic mining industry in the United States, leading to the shutdown of operations or large cutback of work forces. The purpose of this paper is to look at the impact of a layoff on the employees of what was once a major uranium producer in south central Wyoming, twenty months after the final layoff and mine shutdown. INTRODUCTIONDecember 19, 1985, was the date of the final of three successive layoffs over a two-month period, leading to the complete shutdown of Petrotomics Company, a subsidiary of Getty Minerals Company. The final shutdown was due to a combination of depressed U3O8 prices and the takeover of Getty Oil Company by Texaco in January 1984.The layoffs affected 104 employees and included mine personnel, mill personnel and staff. Both hourly and salary workers were involved. The operation was considered non-union, however, a few mill hourly employees were unionized. At the completion of the layoffs. only a handful of employees remained for administrative and miscellaneous functions.For Getty employees, the terms of the merger agreement provided a generous level of separation benefits. The terms that were insisted upon by Mr. Petersen, Chairman of the Board for Getty Oil, stipulated that employees receive one month of severance pay, for each full calendar year of employment up to a maximum of two year's pay. This was the forerunner of what is now commonly known as the ""tin parachute”. All but the union employees of Petrotomics received these separation benefits. Union employees were covered by their separate, less generous, contract.Much of the literature that has been published in recent months has centred around the effects of layoffs on remaining employees, or the psychological effects on the severed employee. This study will emphasize the economic impact and ramifications due to a layoff, using the Petrotomics employees as a case example."

Jan 1, 1989

By D. M. Xue, T. B. Li

"With the increase of human engineering activities, global climate change and active plate tectonics movement, the giant landslide frequently occurred in southwest China, which caused huge property and human losses. Besides, the potential landslides pose severely threaten to the construction and operation of airports, railways, highways and power stations etc. In order to provide accurate guidance for the landslide investigation, stability analysis and mitigation, the giant landslide is redefined according to landslide volume, depth of slip surface, complexity of landslide mechanisms, and degree of landslide mitigation difficulty, and classified with the typological classification approach based on the twofold attributes of landslide behavior including formation mechanisms and reactivation features. Finally, the threefold particularity of the giant landslide is also summarized, which enables a more effective landslide mitigation design.INTRODUCTIONWith the increase of anthropogenic activities, global climate change and active plate tectonics movement such as continual uplifting of Qinghai-Tibet plateau and strong earthquakes, the occurrence of giant landslides was in ascending trend in southwest China (Huang, 2009), which caused serious destruction, and greatly endangers such engineering construction from safety, time and economic aspects as airports, railways, highways, power stations, etc. Giant landslides have huge scale, complex formation/reactivation mechanisms and mechanical behavior. They may not be identified during the hazard investigation, but may be firstly initiated or reactivated due to the following engineering activities, heavy rainfall or strong earthquakes. Consequently, the landslide mitigation is inevitable and costly. However, it is difficult to control the deformation of giant landslide with lack of a correct understanding of genetic mechanisms (Marui, 2012; Zhang, 2000) and the excessive large sliding forces of the slide blocks calculated by the conventional limit equilibrium method. For instance, the failure of anchored pile wall for the No.102 giant ancient landslide (Zhu et al., 2012) and stabilization measures for the Sidi Rached viaduct landslide(Guemache et al., 2011); four rows of piles had not prevented the occurrence of the No.12 landslide in a high fill slope in the Panzhihua airport (Li et al., 2012)."

Jan 1, 2015

By S. Luidold, A. Poscher, H. Antrekowitsch

"The rare earth elements (REE) are nowadays mainly used for permanent magnets, catalysts, hydrogen storage alloys in rechargeable batteries, for glasses, ceramics, and polishing agents. Other important areas of application are phosphors in different types of lamps (fluorescent tubes, energy-saving lamps, etc.). These lamps are often collected and treated at their end of life by disintegration and sorting. However, the obtained fine fractions comprise not only REE-containing phosphors but also small amounts of mercury and are therefore disposed till today in special landfills. Due to the enormous price increase of the rare earths during the last two years, a lot of activities started for extracting these elements from secondary resources such as for example phosphors. All recycling concepts for this task mainly work with hydrometallurgical methods. The large number of different compounds in phosphors with sometimes very different behaviors with respect to their solubility in aqueous phases forms a major challenge to achieve good yields as well as acceptable purities of the produced rare earth concentrates by a process with a reasonable number of operation steps. Therefore, this paper gives at first a brief overview about the compounds, used as phosphors and about existing concepts or investigations. It further describes our own process design and the results, obtained on laboratory scale. INTRODUCTIONThe rare earth elements (REE) have a central position in the industrialised world despite their marginal production volume in comparison to common metals such as aluminium, copper, zinc etc., because they are essential for many applications. They often cannot be substituted without a considerable loss on functionality and quality. This group of metals comprise the lanthanoids (f–block elements, lanthanum–lutetium) as well as scandium and yttrium.The estimated world mine production of REE amounted to 133,000 t rare earth oxide equivalent in 2010, whereat China accounted for 130,000 t or 98 % (Cordier, 2012). The European Union (EU-27) imported 23,013 t in 2008 to cover its demand. The figure 1 shows the fraction of the European member states in terms of the total imports of rare earth compounds from outside the EU-27 (Schüler, Buchert, Liu, Dittrich, & Merz, 2011)."

Jan 1, 2012