Search Documents

By P. Blonde

Recent analysis has suggested that a balanced recovery profile can improve flotation bank performance. Test work was conducted to test the balanced profile concept at the Penhorwood talc mine near Timmins, Ontario, Canada. Plant trials were devised to determine how to control the recovery profile and the resultant impact on grade and recovery in a rougher bank of four cells. Accompanying gas dispersion measurements revealed a maintenance issue with one cell that was corrected. By manipulating air and frother addition it was possible to bring the bank closer to a balanced recovery profile and the down-the-bank grade/recovery improved. Plant production showed an increased talc grade at similar yield with the balanced profile. The results provide justification for a long term plant trial.

Aug 1, 2013

By A. I. A. Salama, M. W. Mikhail

"The existing methods of block diagram manipulation and vanishing variable for flowsheet simplification used in coal and mineral processing circuit evaluation and optimization cannot be easily implemented on digital computer.The signal flowgraph technique is proposed to represent and simplify determination of the relationship between intermediate or end variable and the feed in the flowsheet. Typical and existing circuits are used to demonstrate the application of the proposed technique which can easily be implemented on digital computers.IntroductionRecently there has been much interest in the analysis and optimization of coal and mineral processing circuits to assist in the pre diction of coal and mineral processing plant performance. The block diagram and the vanishing variable were introduced and utilized in the analysis of plant flowsheet. Although the block diagram approach is useful, it requires manual manipulation of the circuit block diagram which may present difficulties in the situation of complex circuits. Moreover, it may not be easy to implement on a digital computer.In this paper, the signal flowgraph technique is proposed to represent the circuit flowsheet and to simplify the determination of relationships between intermediate or end variables (fractional mass) and the feed for any coal and for any mineral processing circuit comprising size and density separators. These relationships are utilized in the analysis and/or optimization of the circuit. The proposed technique is illustrated by considering typical and existing circuits."

Jan 1, 1987

By R. B. Casault, J. D. Boyd, D. R. Bell

"Full-scale sections of three different types of Grade 483 line pipe have been evaluated extensively. The variations in chemical composition, optical microstructure, tensile properties, hardness and Charpy impact toughness with specimen orientation and location were determined. Significant variations in several properties, notably Charpy shelf energy, impact transition temperature, inclusion content and ferrite grain size, were observed for different locations in the pipes. The results indicate that current specifications call for test samples for the most conservative locations, except for impact tests. Minimum Charpy impact values generally occur at the II2-width location, which may be a more appropriate specified test location than the present I/4-width location. The anisotropy of impact toughness, and the importance of low sulphur content and inclusion shape control for adequate toughness in the transverse/rolling-direction orientation were demonstrated. The orientation of impact specimens is critical for spiral-weld pipe, and the current specification test is non-conservative in that it can give results which are two to three times higher than the minimum value for the steel.IntroductionThis report presents the results of an extensive metallurgical evaluation of three different Grade 483 line-pipe steels. The sample material came from full-scale sections of line pipe, which represented current commercial practice at the time of manufacture (1975-1977). Since then, significant improvements have been made in the manufacturers' procedures for producing skelp and pipe, and the line-pipe specifications have been revised. Hence, the information in this report is dated in terms of current design, but it is unique and significant in several respects:"

Jan 1, 1982

By B. Jena, M. Rigaud, S. C. Panigrahy

"The influence of flux addition on the structure and properties of pellets produced from low silica specularite with peat moss and bentonite as binders was investigated. Specific pellets basicities in the range of 0.4 to 3.2 were obtained by the addition of limestone or a combination of dolomite and limestone as flux. A t basicities < 1.6, the bonding in the pellets was provided by a glassy silicate phase. At basicities =1.6, calcium ferrites were the predominant bonding phase. When dolomite was added as a flux, presence of magnesia-ferrite was noted. The reduction behaviour of pellets at different basicities was found to be influenced by the type of flux and binder. The pellet compression strength and swelling characteristics were improved with increased basicity.IntroductionThe properties of iron ore pellets are influenced by the type and nature of the ore or concentrate, additives and their subsequent treatment to produce pellets. The interaction between various constituents of the concentrate and additives, i.e. iron oxides, gangue and fluxes etc. result in the formation of various mineralogical phases which affect the degree and nature of bonding achieved in the pellet and the structure and distribution of pores. The pellet properties such as pellet strength and reducibility are influenced by the extent and type of bonding achieved between the ore particles. In view of the present emphasis on the production of high quality pellets to meet progressively stringent quality control requirements, it is essential to investigate the effect of additives on the bonding mechanism and properties of the pellets.In the past, the effects of additives on the bonding mechanism of pellets have been investigated. It is important to note that the conditions and parameters to be controlled are typical of a given concentrate/ore. In this paper, the results of the investigation on characterization of fluxed pellets produced from a low silica specularite concentrate are reported.This investigation was also aimed at assessing the suitability of peat moss for use as a binder for the production of low silica fluxed pellets. Peat moss is abundantly available in the vicinity of iron ore mines in Quebec and encouraging results have been obtained du ring the production of high silica acid and fluxed pellets."

Jan 1, 1992

By S. Shairp

At the Hudbay zinc pressure leach plant, filtration and washing of the second stage leach slurry takes place on a vacuum belt filter prior to disposal to tailings. Due to periods of poor filterability, laboratory studies were undertaken to investigate the effect of temperature of the filter feed slurry, and to compare filterability to the resulting cake particle size distribution.

Jan 1, 2014

By Richard K. Komarek, Antonios Zavaliangos, Roman T. Dec

Current industrial compacting and briquetting practices are largely based on trial-and¬error techniques. This paper introduces a two dimensional finite element model of compacting/briquetting process in the roller press. Compared with other modeling techniques used in the past, finite element method offers the most versatile approach because it incorporates adequate information about powder behavior, geometry and frictional conditions and offers predictions for the density distribution, velocity field, stress distribution, roll force, roll torque and other important process variables. More over, when the model includes elasticity, it offers predictions on the internal stress state in the briquet after its exit from the pressing zone. This enables to perform realistic computer experiments which are helpful for establishing the pressing system design, forming cavity geometry and process conditions necessary to produce compacted or briquetted product with the desired properties.

Jan 1, 2004

By Kyeong Woo Chung, Ho-Sung Yoon, Jyothi Rajesh Kumar, Chul-Joo Kim, Sung-Don Kim

The aim of the present study is to investigate the extraction, separation and recovery of the indivisible metals of dysprosium and neodymium from permanent magnets scrap leach liquor solutions with meaningful recovery. The present experimental development focused on dysprosium separation from neodymium and recovery by suitable mineral acids. Fundamental studies of the effect of time, pH and extractant concentration on the metal separation were conducted followed by proposal of a mechanism for extraction. Process development included generation of McCabe-Thiele diagrams and counter current extraction (CCE) studies. After loaded organic generation from the CCE process, this was followed by scrubbing studies as well final recovery of dysprosium.

Jan 1, 2014

By J. F. K. Brown

WHEN I first received the kind invitation extended to me by the Mining Society of Nova Scotia, I read over very carefully the suggested title-"The importance of long-distance planning and budgetting in modern methods of mining, and the advisability of working to some definite plan". I came to the conclusion that I might as well confess my inability to handle properly such a vast and intricate subject within the scope of any one paper. More properly, I think a round-table discussion should be indulged in-a sort&apos; of symposium carried on in similar fashion to the World Power and Coal Conferences- you know, a committee for this, a committee for that, and, finally, a committee to see what the committees are doing. Weil, your Secretary&apos;s suggestion is just like that- much too comprehensive for any half-hour&apos;s presentation. As a paper, also, it either becomes too general and therefore uninteresting, or i.t descends into detail and describes means and methods to the end desired, which have little attraction because they were designed to meet quite different conditions than those my audience would mentally be considering. Of the two evils facing me, I have chosen the one that sticks to the generalities. Your Secretary&apos;s query almost automatically divides itself into two distinct phases: First, the importance, and second, the advisability, of planning. Let us dwell for the moment on the second, because, if we can prove advisability, that leads to desirability and, finally, to doing. Proving is the difficult part of the little problem. Here was something I, personally and as a mining engineer, had been battling for all my corporate life without being able to prove it to anybody. Then I saw the way out of that. I perceived I could put that little question of advisability on another basis altogether-:put it in the class of "coming- some day- soon" whether you or l or anybody else liked it or not; call it, if you please, mandatory, certain, necessary, enforceable planning. All of which means that the problem of advisability has rather suddenly become the very practical one of "how to do it". Why?

Jan 1, 1937

By A. A. Brant

ONE of the reasons advanced for the decline in prospecting and discovery is that, as regards surficial examination, the law of diminishing returns is becoming applicable. Fewer surficially unprospected fields remain; therefore, fewer discoveries by such means result. Much in the nature of mineral resources remains to be unearthed, but even now, and more so in the future, will discovery depend on painstaking petrographic and structural mapping, aided, where necessary, by judicious applications of all the complementary scientific knowledge and devices (e.g., thin section microscopy, geophysics, and drilling) that experience proves effective in localizing a mineral deposit even beneath drift, lake, or muskeg. It is to be expected, then, that the rate of discovery will decrease, that the cost per discovery will greatly increase, and that the work of discovery will become more and more the careful, methodical assembling of field data, conscientiously interpreted on the basis of scientific knowledge by trained, experienced operatives. In view of these trends, the status of applied geophysics to Canadian mining exploration and development work might well be reviewed. The niche which geophysics may occupy relative to geological surveying and drilling has been clarified by the last twenty years&apos; experience. The cloud of somewhat justifiable scepticism that followed the &apos;geophysical promotion&apos; period of the late 1920&apos;s has lifted. Mining, exploration, and finance companies, in open-minded fashion, are seeking sound advice as to what are the scope and limitations of the geophysical methods at present practised. The purpose of this paper and the following one is, therefore, as far as lies within the author&apos;s power, to review briefly the geophysical methods at present in practice in Canada, and, at greater length, to joint out impartially and critically their scope, merits, shortcomings, an possible future development. The treatment will be non-technical, the hope being that an accurate statement of the present status of geophysics in Canada may do much to result in a sounder, saner growth of what, in the future, shall undoubted} y prove an increasingly useful tool in exploration and development work. ?

Jan 1, 1942

By Matthew R. Ward

This paper aims to describe the reasons and methods to extend enterprise networks into underground mines. Currently mines use a number of communication networks for telephones, PLCs, two-way VHF radio and computer networking. Each system can have different wiring, protocols, converters and interfaces all which require expansion and maintenance. The convergence of voice, video and data using Ethernet and TCP/IP has the very real benefit of one ?wire? for underground networks. Now that the majority of underground equipment can communicate using TCP/IP, network convergence can offer reduced network expansion and maintenance costs. Cost savings are good, but the truly exciting aspect of network convergence using Ethernet is the low-cost, high speed wireless networking now available . These wireless networks offer an opportunity to facilitate mining automation even on a small budget. How would mine operators change they way they operate if they could gather vehicle location and data in real time? What about controlling equipment remotely? The list of applications is long and includes traffic control, dispatching, real-time ore blending, tele-operation, automated production reporting, vehicle health monitoring, elimination of paper forms and immediate network access for surveyors and geologists. An ideal converged network for underground mining would be robust, inexpensive, easy to expand, enable fast and secure connections while keeping voice communication performance equivalent or better than what is now provided by VHF radio

Apr 1, 2005

By W. G. Q. Johnston, J. S. Fox

"A semi-continuous belt of Aphebian magnesian extrusive and related sub volcanic rocks has been delineated by the authors over a distance of 150 kilometres in the central La Ronge lithostructural domain in Saskatchewan. They range in composition from peridotite to basalt and attain true thicknesses of up to 800 metres. For the most part, they are confined to a basal position in the La Ronge/Wasekwan metavolcanic sequence, and appear to have been extruded onto sialic crust. However, at Lynn Lake, Manitoba, in the eastern continuation of the domain, similar rocks seem to be found only at a relatively high stratigraphic level.Although metamorphism seems to have obliterated any quench textures that may have existed in these rocks, ultramafic pyroclastics, pillows and amygdules as well as intercalated, fine-grained clastic sediment attest to the volcanic nature of these rocks. Bulk chemical analyses indicate that these rocks are heterogeneous, with komatiites, tholeiitic picrites and even rocks with some of the characteristics of boninite all being present. The close temporal and spatial relationship of ""boninites"" and komatiites in the belt may suggest a high degree of Aphebian mantle inhomogeneity in the domain.Nickel-copper mineralization has been found in differentiated tholeiitic stocks within the La Range domain (e.g., at Lynn Lake), but none has yet been found in the ultramafic volcanics. However, the tholeiitic picrites do host one economic gold deposit - the Agassiz Mine at Lynn Lake .Because of the depleted nature of their mantle source, the ""boninites"" of the domain are not considered to be likely hosts for mantle-derived nickel sulphide mineralization. However, the opposite is true of the komatiites, and this points to the need for whole-rock geochemistry in setting priorities for nickel exploration in the belt. In contrast, all of the magnesian rocks of the domain probably have the same gold potential. Inasmuch as the geophysical response to gold mineralization in the domain is likely to be unpredictable, lake-sediment geochemistry, followed by base-of-till and/or alteration oriented lithogeochemistry, should be emphasized during gold exploration."

Jan 1, 1981

By A. Pearson, F. A. Auld, S. O. Colbeck

"""The theory of buckling of shafts and Steel tunnel-linings"" was published by E. Amstutz in 1970 and commented on by S. Jacobsen in 1974. The authors have revised and enhanced Amstutz’s work to address Jacobsen's comments on its limitations and to extend its validity over a wider range of pipe/shaft geometries, including those commonly found in deep mine access shafts. The author has looked at Amstutz’s assessment of strengthening with flexible shear anchorages and adapted the theory of non-linear shear deformation response of bolts to develop a method of assessing increased buckling capacity utilising the full plastic shear capacity of studs. INTRODUCTION “Amstutz Buckling” refers to the buckling of pipe embedded in concrete under external uniform pressure. In terms of a mining environment, this relates directly to the design of a watertight shaft. This load case will commonly occur where a main shaft is cast against a geostatically stable primary liner and the only load applied to the final shaft is that of a uniform ground water load. Ernst Amstutz wrote his first paper on buckling of pressure-shaft steel linings in 1950 and subsequently improved his theory (Amstutz, 1970), which was then widely adopted for use within the industry. Years later, an alternative approach (Jacobsen, 1974) was proposed. Within his paper Jacobsen critiques Amstutz work, identifying some mathematical inconsistencies and highlighting limitations of the theory imposed by approximations adopted by Amstutz. Despite these limitations Amstutz work has still been used as the favoured design theory for use in the mining industry. In reviewing this body of work the author realised that with the advent of readily available computing software it was possible to adopt an iterative approach using Amstutz approximate formulae to find a solution to the original precise formulae, thus eliminating the limitations highlighted by Jacobsen The shear deformation to load characteristics of bolts has long been established (Crawford & Kulak 1968) and used for the plastic design of bolted connections in shear. This relationship is directly transferable to the design of shear studs, typical properties are well known, and actual values easily established in simple lab tests. The author has taken this relationship and modified Amstutz theory (Amstutz, 1970) for shear anchored strengthened liner buckling, to give a more efficient solution, using readily available material properties."

Jan 1, 2019

By A. Fahr, T. Byczkowski, M. Genest, C. Mandache

"Layered aluminum structures assembled with rivets are often found in aircraft fuselage. These structures are exposed to various mechanical loads and a range of environmental conditions that contribute to their ""aging"". The rivet holes are the source of stress concentrations and the location of crack nucleation and growth. Detection and sizing of second and third layer cracks under fasteners represent a major challenge for non-destructive evaluation (NDE) technicians. Electromagnetic methods are currently the most feasible NDE techniques that are capable of successfully inspecting such structures. However, different probe lift-offs, due to protruding rivets and paint coatings, or interlayer separations, due to sealant or air gaps, pose difficulties in detecting and sizing cracks. In addition, the use of conventional eddy current technique is limited due to the inverse relationship between the probe spatial resolution and its field penetrability. In this paper, we present an alternative approach that overcomes the previously mentioned shortcomings by using pulsed eddy current excitation and magnetoresistive sensor pick-up. Various signal manipulations are employed for defect detection and quantification."

Jan 1, 2006

By James D. Bittner

Separation Technologies, LLC (ST) has developed a processing system based on triboelectric charging and electrostatic separation that provides the mineral processing industry a means to beneficiate fine materials with an entirely dry technology. The environmentally friendly process can eliminate wet processing and required drying of the final material. The process requires little if any pre-treatment of the material other than grinding and operates at high capacity ? up to 40 tonnes per hour by a compact machine. Energy consumption is low, approximately 1 kWh/tonne of material processed. Since the only potential emission of the process is dust, permitting is typically relatively easy. In contrast to the other available electrostatic separation processes that are typically limited to particles greater than 75 µm in size, the ST belt separator is ideally suited for separation of very fine (<1 µm) to moderately coarse (300 µm) materials with very high throughputs. The triboelectric particle charging is effective for a wide range of materials and only requires particle ? particle contact. The small gap, high electric field, counter current flow, vigorous particle-particle agitation and self-cleaning action of the belt on the electrodes are the critical features of the ST separator. The high efficiency multi-stage separation through charging / recharging and internal recycle results in far superior separations and is effective on fine materials that cannot be separated at all by the conventional electrostatic techniques. Since 1995, this triboelectric process has been extensively used for the beneficiation of coal fly ash with eighteen separators in place and over 130 machine-years of operation at locations in North America and Europe. ST has also installed separators for the beneficiation of industrial minerals in North America and Europe. The technology has been successfully applied to the beneficiation of a variety of minerals including calcium carbonates, talc, barite, and potash.

Aug 1, 2013

By C. M. Campbell

THE dire effects of rapidly vanishing natural resources, widespread unemployment, and increased debt and taxation in recent years have challenged Canadians to produce a practical solution to these national economic problems. In more recent months, wars and rumours of war have indicated, among other things, the need for better control of our mineral wealth. The erection of a smelter on the lower mainland coast of British Columbia, treating all Western ores, and such ores as it will be found advisable to import, will make an important contribution toward a solution of these problems. It is believed that the ores tributary justify a smelter of major proportions. A stock-taking to confirm this can be made with reason-able accuracy in a short time, and this should be undertaken without delay. Enough general information is, however, available .in this paper to justify the technicians of the Department of Mines at Ottawa and of interested smelting companies making a preliminary study of the matter. THE DEFENCE ARGUMENT As a factor in rearmament, metals play a vital part. That rearmament is to continue on an increasing scale is indicated in Premier Chamberlain&apos;s address of October 3rd last, when he said: ?&apos;For a long period now we have been engaged in this country in a great programme of rearmament which is daily increasing in pace and volume. let no one think because we have signed &apos;this agreement between the four powers at Munich we can afford to relax our efforts or call a halt in our armaments at this moment&apos;. As matters stand, the facilities in British Columbia are entirely out of line with the strategic importance of this Province as the Western Front of Canada and the Empire. All our copper ores, and an appreciable part of our lead and zinc ores, are sent for treatment to Japan, United States, and Europe, while we import our iron and alloys. A treatment plant on this Coast would not only give us control of war metals and chemicals but it would provide an increased industrial and research population, badly needed in this area and of the greatest value in the case of war. This is where the mining industry can do its bit.

Jan 1, 1939

By A. S. H. Kabir

Due to the high specific strength and excellent corrosion resistance, Ti-6A1-4V has been widely applied in aerospace industries. In this study, the welding performance of 3.2-mm and 5.1-mm thick Ti¬6A1-4V sheets was studied using a 4 kW continuous wave Nd: YAG laser. It is found that the use of filler wire, matching the parent metal composition, can bridge the joint gap and produce full penetrated welds up to a width of 0.6 mm without cracking. The laser welds were characterized in terms of the bead geometry, defects, microstructures, and hardness. With increasing joint gap, the percent porosity area increased, reaching just over 1% of the fusion zone area at a gap width of 0.6 mm for the 3.2 mm and 5.1 mm thick sheets. The maximum underfill depth in the Ti-6A1-4V laser welds was about 5% or 7% of the sheet thickness for the 3.2-mm and 5.2-mm thick materials, respectively, meeting the AWS D17-1 specification. The microindentation hardness was maximum in the fusion zone and sharply decreased through the heat affected zone until reaching the base metal value.

Jan 1, 2011

The extractive industry has the potential to impact the health and well-being of workers, families and surrounding communities. In the current environment of social performance, project planning considers that activities should be conducted in the best environmentally, socially and economically acceptable way across the development cycle (i.e. from exploration ? post-closure). In this context, health impacts of mining can be mapped and extend over the Life of the Community and can encompass worker injury and disease, exposure to communicable and non-communicable diseases, and health outcomes specific to family and community health and well-being outside the fence. To contribute to an emerging field focused on Health and the Extractive Industry, this paper reviews and compares health activities extracted from social and environmental reports published by selected major mining, oil and gas companies with operations in Australia and Canada. The objective of this review is to map corporate approaches to public health management across our previously developed Life-of-Mine within Life-of-Community (LOMLOC) framework in order to identify and compare trends and behaviour in corporate health investments across the project cycle, as well as identify the level of prevention targeted by this investment activity (i.e. primary, secondary and tertiary prevention of detrimental health impact). With the extractive industry facing ongoing rapid growth worldwide, this paper provides preliminary comparative information about corporate health spending by some companies in Australia and Canada. This information serves as a resource for minerals industry managers, civil society and regulators regarding current health management approaches in this sector.

Aug 1, 2013

By R. Salimi

Tricalcium aluminate hexahydrate (TCA) is used as filter-aid for security filtration in the Bayer alumina process. TCA is typically produced on-site by mixing Bayer liquor with slaked lime. Specific properties are required from the TCA to ensure adequate filter throughput, lifetime and importantly effective reduction of solid/colloidal impurities from the solution. The effect of reaction time on morphology and particle size distribution of tricalcium aluminate was studied for a batch experiment at simulated process conditions. It was found that reaction time plays a critical role on the morphology, crystal structure (diameter and crystallinity) and particle size distribution. In the early stages of the reaction, nucleation dominates the crystallization process followed by growth dominated by agglomeration up to a mean particle size of 10 µm. The particle morphology shifted from an irregular shape to more spherical throughout the course of the reaction.

Jan 1, 2014

By O. Babak, J. G. Manchuk

ABSTRACT A significant factor in evaluating bitumen recovery from an oil sands mine is the particle size distribution (PSD). Increased understanding of mined ore quality and improvement in predictions of recovery can be achieved through PSD modeling. This paper addresses PSD modeling using geostatistics. PSDs may be described using many discrete particle sizes, making this a challenge. The approach parameterizes PSDs with a few statistics. A lookup table is used to reconstruct the PSDs based on models of the statistics. The workflow is applied to Total E&P Canada’s Joslyn Lease and yields good results that reproduce input statistics without introducing artifacts.

Jan 1, 2013

By R. L. Bruening, L. Navarro, Izatt. S. R., R. Adiga, R. M. Izatt, N. E. Izatt, A. Sharma, N. R. Patel, B. V. Rao

Bismuth is a notorious contaminant in the electrolytic refining of Cu that can cause cathodes to fail to meet ASTM International standards and not be suitable for use in Cu rod and other downstream products. Bismuth can significantly decrease electrical conductivity, decrease the mechanical strength of the annealed wire, retard recrystallization, and sometimes induce hot shortness during the hot rolling process in the production of rod. As a result, the control of Bi in the refinery tankhouse must be carefully managed. This paper describes how SuperLig® Molecular Recognition Technology (MRT) is being used for Bi removal at the Birla Copper Dahej Copper refinery. The operation of the SuperLig® MRT Bi removal plant is described and data on Bi removal efficiency are presented. INTRODUCTION Hindalco’s Cu division, Birla Copper, operates one of the largest Cu refineries in the world at Dahej, Gujarat; India. The main feed for this refinery is produced at the company’s smelter. Due to its massive production capacity, this operation mainly relies on imported Cu concentrates resulting in a variety of metals being carried out as impurities in the Cu anodes because pyrometallurgical technologies alone are not enough to remove them to the extent required. Metal impurities found in Cu ores include Fe, Zn, As, Pb, Bi, and Sb. During electrorefining, less noble metals dissolve in the electrolyte gradually increasing their concentrations creating the need for electrolyte control mechanisms that remove these impurities with varying degrees of success (Wang, 2004; Navarro et al., 2013.) Bismuth is one of the most significant impurities in a Cu refinery because it has the lowest ASTM product specification. This situation is critical because the Bi potential is very close to that of Cu making it possible to plate in the Cu cathode directly. Also, Bi can precipitate at high concentrations causing floating slimes and reduction of current efficiency (Ballinas, San Miguel, Munoz, & Gyves, 2003). Production of high purity cathodes from feed stock containing a diverse range of metal impurities becomes a major challenge in the refining of Cu (Izatt et al., 2015). In this work, the purification strategy followed by Birla Copper for the removal of Bi using a separation process based on MRT is presented, outlining the loading and stripping performance of SuperLig®83 and the benefits of using MRT over other lower selectivity methods where hazardous materials are produced instead of high purity products.

Jan 1, 2019