Search Documents

By R. A. Gannicott

Trend surface analysis was used to investigate the geochemical dispersion patterns of Si, Ai, Fe, Mg, Ca, Na, K, Ti and Rb in the footwall of the Seneca massive sulphide prospect in southwestern British Columbia. Surfaces for various element ratios were also produced to see if the distributions of the elements are related to each other. Trends developed by the elements redistributed during hydrothermal alteration may be difficult to detect for various reasons, such as too few and widely separated sample points, random analytical errors or local variations in rock chemical composition that are not related to regional trends. Trend surface analysis is useful to distinguish regional trends from local fluctuations. The computer program used in this study is capable of calculating surfaces up to the 6th degree polynomial, but provides for automatic termination when the variables in the equation for successive surfaces become effectively collinear. With the relatively small number of data points used (21 samples) in this study, such termination occurred after the quadratic surface. Results show that, at the Seneca prospect, Mg and K increase, and Na and Ca decrease, toward a common centre which corresponds closely with the best drill-core intersections of ore. The centre is interpreted as a volcanic vent and as the source of mineralization . Quadratic surfaces for element ratios show that K/Ca decreases and Fe/Mg increases away from this vent. Thin-section and X-ray diffraction analyses indicate that these variations reflect sericitization of plagioclase and an increase in the Mg content of chlorite near the vent. The mineralization , rock types and element dispersion patterns at the Seneca prospect are similar to those reported for volcanogenic massive sulphide deposits at Bathurst, New Brunswick, and in the Hokuroko district of Japan.

Jan 1, 1979

Forward-Looking Statements Information set forth in this presentation may involve forward-looking statements under applicable securities laws. Forward looking statements are statements that relate to future, not past, events. In this context, forward-looking statements often address expected future business and financial performance, and often contain words such as "anticipate", "believe", "plan", "estimate", "expect", and "intend", statements that an action or event "may", "might", "could", "should", or "will" be taken or occur, or other similar expressions. Forward-looking statements or information relate to, among other things expected iron ore demand, timing for a production decision, expected share price drivers, potential railway options, timing, grade and quantity of potential resource estimates, employment and economic benefits, taxation estimates and timing of key project milestones. By their nature, forward-looking statements involve known and unknown risks, uncertainties and other factors which may cause our actual results, performance or achievements, or other future events, to be materially different from any future results, performance or achievements expressed or implied by such forward-looking statements. Such factors include, among others, the following risks: the risks associated with the need for additional financing; operational risks associated with exploration; fluctuations in commodity prices; title matters; environmental liability claims and insurance; reliance on key personnel and other risks and uncertainties discussed in the management discussion and analysis section of our interim and most recent annual financial statement or other reports and filings with the TSX Venture Exchange and applicable Canadian securities regulations. Forward-looking statements are made based on management's beliefs, estimates and opinions on the date that statements are made and the Company undertakes no obligation to update forward-looking statements if these beliefs, estimates and opinions or other circumstances should change, except as required by law. Investors are cautioned against attributing undue certainty to forward-looking statements. NI 43-101 Qualified Person Alderon?s exploration work on the Kami Project is supervised by Edward Lyons, P.Geo., the Chief Geologist for Alderon and a Qualified Person as defined byNational Instrument 43-101. Mr. Lyons has reviewed and is responsible for the technical information contained in this presentation. Mr. Lyons is a member in good standing of the Association of Professional Engineers and Geoscientists of British Columbia (APEGBC) and the Professional Engineers & Geoscientists Newfoundland & Labrador (PEGNL) as a registered Professional Geoscientist (P.Geo.).

May 1, 2011

By Z. Ren, M. Tomlinson, E. Asselin

"Organic carbon blinding is a common, yet often partial, solution to the reduction of preg-robbing. A quantitative method to assess the extent of adsorption of a given blinding agent is presented herein. The adsorption of several blinding reagents on various carbon samples is quantified using electrochemical impedance spectroscopy (EIS). EIS results showed that kerosene is more strongly adsorbed on carbon than sodium lauryl sulphate (SLS), while SLS can hinder the charge transfer process of the oxygen reduction reaction on the carbon surface more effectively. The effectiveness of SLS is pronounced when its concentration is higher than 100 ppm. Raman spectra are presented for selected carbon samples: as the area ratio of the disordered peak to the graphitic peak increases, blinding agent adsorption increases.INTRODUCTION The presence of naturally occurring constituents in gold ores may adversely affect the extraction of gold in cyanide leaching since the gold cyanide complex, Au(CN)2–, can be adsorbed by these constituents (M. Adams & Fleming, 1989; Afenya, 1991; Miller, Wan, & Díaz, 2005). Such ores are known as “preg-robbing”. Preg-robbing behavior may arise from natural carbonaceous materials in the ore (M. Adams & Burger, 1998). In the past decades, a number of pre-treating methods have been developed for refractory carbonaceous ores (Arriagada & Osseo-Asare, 1984; Beer, 1994; Dunne et al., 2007; Jiang, Liu, Xiao, & Yang, 2012; Kohr, 1997; Kulpa & Brierley, 1993; Menne, 1992; Menne & Revy, 1994; Moyes & Houllis, 2010; Petrie, Craw, & Ryan, 2005; Simmons, 1996). The method known as blinding is one of the most effective and economical pre-treatment methods (M. D. Adams & Burger, 1998; Albert, 1923; Darrow, 1924; McQuiston & Shoemaker, 1975; Van den Berg, 2000). Blinding, also referred to as blanking or passivation, uses a chemical reagent to passivate the preg-robbing carbon by selective absorption or wetting (Bas, Altinkaya, Yazici, & Deveci, 2012; Brierley & Kulpa Jr, 1993; Dunne et al., 2012; Van den Berg, 2000; Yang, Qian, Song, & Dong, 2013; Yen, Amankwah, & Choi, 2008; Zhou, Jiang, & Choi, 2014). Organic reagents, which selectively adsorb on the surfaces of activated carbon and “smother” the surface, have been used for blinding carbonaceous matter in gold ores prior to cyanidation. Two comprehensive studies by Abotsi and Osseo-Asare and Adams and Burger have been published on this topic (Abotsi & Osseo-Asare, 1986; M. D. Adams & Burger, 1998)."

Jan 1, 2017

By V. Aitken

Line-of-sight radio control has received widespread acceptance for use in many mining methods because today’s technology offers improved economics and personnel safety. Significant advances in higher autonomy for mining machines are not currently seeing widespread use even though they offer great future potential. With autonomous capabilities being a longer-term goal, a logical sequence of advances based on TeleRemote control is proposed. Under Tele - Remote control, the operator is in direct control of the machine at all times. Three levels of Tele - Remote control systems are presented including line-of-sight, extended line-of-sight, and full load-haul-dump applications. Distributed control and sensing subsystems arranged in a vehicle control area network support incremental system expansion through the three levels of TeleRemote control and prepare the machine for integration of higher levels of automation as mature technology becomes available. This approach allows full exploitation of today’s mining automation technology with a flexible future growth path.

Jan 1, 1998

By W. J. Blackstock

Introduction To The great majority of people, the term 'strip coal' has little or no meaning, or if it has any significance it is thought to refer to a poor grade of coal that had to be accepted during the war because no other fuel was available. Few people in the Province of Alberta realize the magnitude of our coal stripping industry, and fewer realize that strip coal has been available to domestic consumers for at least forty years. Among the first in the field of strip coal mining in Alberta were the Tofield Coal Company, Ltd., and Sterling Collieries Company Ltd. It was not until the advent of World War II, with its huge drain on industrial and domestic coal sup? plies produced by the underground mines, that some other source of coal was seriously sought. The tremendous shortage of manpower du ring this period of National emergency made it imperative that any increase in the coal production must be procured on a high tonnage per man-hour basis. It was therefore natural that the highly mechanized strip mine should be eagerly encouraged and subsidized by the Governmental agency - the Emergency Coal Production Board - under the very able direction of Mr. G. A. Vissac.

Jan 1, 1949

By J. B. Edwards

"The case is presented for the use of simulators for the computer-based training (CBT) of mining plant operators and for introducing them to automatically controlled systems. As well as their use in the classroom, the role of simulators is examined for ""on-plant"" use in trouble-shooting, fault-finding and maintenance of automatic systems. Case studies are presented showing how specific simulators are becoming established or have potential in the areas of automated materials handling, machine testing, setup and guidance. The evolution of scientific simulations into simulators of widespread practical use is discussed and present-day limitations of computer speed and graphics are considered. Related areas of research for the Canadian Centre for Automation and Robotics in Mining (CCARM) are identified.IntroductionCCARM's Commitment to Simulator DevelopmentAs automation is progressively developed and exploited in mining operations, there arises an urgent need to educate and train staff responsible for its introduction and operation in our mines and for its maintenance. For this purpose , an essential ingredient of an automation program is the development of appropriate mining system simulators for use by a wide variety of personnel. The author has been fortunate to have been closely involved with the development of automatic control systems for a variety of mining machines and mining systems in the United Kingdom. A key ingredient of the research phase in each case has been the use of simulation techniques. As projects have moved toward their commissioning and exploitation phase, the simulations have evolved into simulators tailored for use by machine operators and maintenance personnel. Illustrative case studies are presented later. The researach of the newly constituted Canadian Centre for Automation and Robotics in Mining (CCARM) will likewise involve extensive simulation, and the development of simulators (from the scientific programs) for use at the mine by operators and technicians will be given high priority in the Centre's over-all work program."

Jan 1, 1990

By B. Lewis

Paper did not make deadline for printing

Jan 1, 1982

By K. G. Chipman

THE discussion on Dr. Chipman's paper, Mapping by the Topographical Survey, centred mainly on the urgent need for aerial photographic reconnaissance of unmapped portions of the country as an initial phase in the provision of suitable topographical maps for use as a guide in geological mapping, prospecting, exploration, and development work in the areas concerned. This, ir was pointed out, would necessitate an expansion of the topographical work of the Bureau of Topography to keep pace with the photographid work and to meet the demand for maps for use by geologists of the Bureau of Geology and others. A resolution requesting Institute Council to make representations to the proper authorities, urging that aerial photography and topographic map-ping be greatly expanded to meet the pressing needs of the situation, was moved by DR. W. F. JAMES and seconded by MR. L. G. SMITH, and carried unanimously. The full text of the resolution appeared on page 221 of the May BULLETIN. Others who spoke in support of the resolution were MESSRS. E. S. MOORE, L. B. ROCHESTER, F. D. SHEPHERD, and W. J. WRIGHT. Dr. Hansen then presented his paper, Mapping by the Geological Survey, discussion on which is summarized below. MR. FRANK EBBUTT(l) spoke of the very valuable service the Geological Survey bas rendered the mineral industry, and indeed the whole nation, in its century of existence, despite the very inadequate financial support it has received. Now, more than ever before, a strong and expanded Geological Survey is essential if the Industry is to continue to prosper. Our known ore reserves are being depleted very rapidly, and we are finding no new orebodies to take their place. As an aid in prospecting and exploration, and also in the development of orebodies when they have been found, we must have geological maps of the vast sections of the country which at present are unmapped or inadequately mapped. The Institute should make every endeavour to have the Geological Survey strengthened so that such maps may be made available as soon as possible.

Jan 1, 1944

By C. Mattich, Å. Holmström, L. Hedström

"The fluidized bed at Division Ministro Hales (DMH) division of Codelco in Calama, Chile is currently the largest operating roaster for partial roasting of arsenic rich copper concentrates. The roaster converts the Mina Ministro Hales (MMH) enargite rich (Cu3AsS4) copper concentrates into calcine with a low arsenic content that is suitable for mixing with other copper concentrates feeding a flash furnace. The plant sets a new standard for the processing of arsenic rich concentrates, both from the quality of the calcine as well as the environmental performances. The process technology and expertise are based on the solid practical experience of treating arsenic rich concentrates from both the Boliden smelter and Outotec.The partial roasting process is located next to the mine and concentrator and includes a sulphuric acid plant with auxiliary equipment. The produced calcine has an arsenic content significantly below target and the residual sulphur meets the requirement of the flash furnace. The plant operates with high efficiency cyclones resulting in a low amount of calcine passing to the hot electrostatic precipitator (HESP). The small flow of HESP calcine dust can be combined with the low arsenic calcine and still meet the flash furnace feed arsenic requirements.SO2 formed during roasting is converted into sulphuric acid, while volatized arsenic is recovered in the wet gas cleaning section of the acid plant along with a large proportion of antimony present in the MMH concentrate. Arsenic is stabilized as calcium arsenate and sent to disposal at a specially prepared site.The present production rate (September/October 2015) is close to or higher than the original maximum design capacity of the plant.INTRODUCTIONMineralogyThe mineralogy of an ore and concentrate is important, since there is a direct link between roasting performance and concentrate mineralogy. The MMH concentrate has a good combination of minerals that makes the roasting process efficient and flexible. The main minerals are pyrite, enargite and chalcocite (Figure 1). The inert content is about 15% and consists mainly of silicate and alumina based minerals. The lead content is very low and this is desirable, since the presence of even a small amount of lead will cause a substantial increase of sintering during roasting."

Jan 1, 2016

By Tim Gartner

This paper introduces a new application of a proven technology to provide dynamic, voltage regulation in underground mine electrical distribution systems. This technology acts to ?stiffen? the electrical power feeding continuous miners and generally raise and improve the voltage regulation at the continuous mining machines which may be located over long cable distances from the mine incoming electrical substation. This is extremely valuable for large underground continuous mining operations that use high power electrical mining machines fed over very long cable lengths (measured in 10s of km, from mine shaft to mine operating face). This new technology provides fast acting dynamic voltage regulation (voltage support) while starting continuous borers and extensible conveyor belts. Additionally, if the mine suffers from a lower distribution voltage due to long cable lengths, this new technology will raise the overall voltage at the mining machine, which can increased mining machine production and lead to longer motor life. The technology is based on voltage source converters operating as static VAR compensators specially packaged for the harsh underground mine environment. While static VAR compensator technology has been successfully used in utility and large industrial applications for many years (including open pit mining and arc furnaces), it has not (until now) been applied in underground mining. The paper will present the problem of poor voltage regulation in underground mines on weak electrical utility networks. It will then discuss some of the alternatives that have been used to resolve this voltage problem. It will then introduce the new technology used to solve the problem and review the issues involved in using this technology in the harsh underground environment. Finally, the paper will present preliminary performance results from an actual installation in a large underground continuous mining operation in Canada.

May 1, 2003

By Fazel G. Jahromi, Ahmad Ghahreman

"Atmospheric leaching of arsenical sulfide concentrates, and especially enargite leaching, is one of the major challenges within the current hydrometallurgy research area. One of the recent processes developed for sulfide ore treatment is atmospheric leaching in the presence of AF 5, a novel carbon based catalyst, in chloride media. The quantification of different ion concentrations during enargite and chalcopyrite leaching in the presence of AF 5 were measured and the copper recovery rates of 97% and 96% were achieved. The objective of this study is to shed light on the leaching mechanism of the sulfide minerals. Based on the speciation of iron and copper by different titration methods, the AF 5 catalyst first reduced ferric and cupric ions and then oxidized ferrous, cuprous and arsenite ions. The oxidation behavior of the catalyst enhanced the leaching results. The AF 5 catalyst also caused in situ precipitation of scorodite in leaching experiment. The speciation of ions in the chloride media were simulated by Phreeqc software and the dominant species in the leaching solution were determined.INTRODUCTION The hydrometallurgy of copper has been used for several decades and is still under development for more complex copper sulfide minerals due to their refractory nature. Most of the world copper reserves are in the form of chalcopyrite; and enargite is known as a major contaminant. Pyrometallurgical processing of enargite is problematic due to arsenic release and tight environmental regulations (Peacey, Gupta, and Ford n.d.). On the other hand, lower recoveries in the hydrometallurgical processes make most of these processes impractical. Several leaching processes have been developed for the leaching of copper sulfide minerals. Some of the common treatment methods for copper sulfide minerals are pressure oxidation leaching (POX), CESL, Activox, Albion process, atmospheric ferric sulfate leaching, Dynatec, Galvanox, and Hydro copper process (Barr, Defreyne, and Mayhew 2005; Conner and Anderson 2013; D.G. Dixon, Mayne, and Baxter 2008; Hyvärinen and Hämäläinen 2005; Palmer and Johnson 2005; Rohner, Bartsch, and Ngoviky 2012). Generally it is not viable to dissolve copper sulfide minerals at ambient pressure in mild acidic media and dissolution of these refractory minerals requires harsh conditions in the presence of oxidant materials (Biswas and Davenport 2002). Ferric ions have been used as an oxidant in different media in copper sulfide leaching processes. U. S. Bureau of Mines’ Reno Metallurgy Research Center in 1969 (Haver and Wong 1971) investigated ferric chloride leaching of chalcopyrite. Dutrizac and Macdonald (1972) studied ferric sulfate leaching of enargite. Based on this study, 50% of the copper was recovered at 80-85 ºC after 7 days of leaching. Cupric ions can also be used as an oxidant. Parker, Paul, and Power (1981) stated that cupric/cuprous couples are more effective than ferric/ferrous couples in chloride media because they are rapid and reversible. The Hydro Copper process leaches copper sulfide minerals in chloride solution catalyzed by cupric ions. In this process, copper dissolves as cuprous ions in presence of cupric ions (about 10 g/L) (Hyvärinen and Hämäläinen 2005)."

Jan 1, 2017

By L. Paulino, R. A. Camilli, J. Yamamoto, J. C. Araujo

The first paper presented on this work [1], showed how bath ratio was increased from 78% to over 95% using a structured approach to reduce bath chemistry variability. This update will illustrate the steps taken and update the results presented earlier, showing the effects of long power interruptions and several load reductions as well as load increase during the period from 1999 to 2005. Current efficiency was affected by such processes upset; however, bath ratio in range (±0.05) is still higher than 90%, even after an increment of more than 6 kA. This review will explain each of the steps taken to reach stability in this critical smelting parameter.

Jan 1, 2006

By T. Billotte, G. Tirand, J. Zollinger, V. Robin, B. Rouat, D. Daloz

The grain structure prediction of metallic alloys during a welding process is often an issue. In addition to the welding parameters and the alloy nominal composition and properties, the base metal grain structure and chemical homogeneity also play an important role in the formation of the final microstructure. In this paper intensive characterisation of solidification structure in gas tungsten arc welding of Ni base alloy 600 are described. It is shown that in transverse section of the weld, while the grain structure shows some texture following constrained solidification growth, grain density in the weld is similar or greater than grain density in the heat affected zone. This suggests that simulation of the welding structure needs, in order to be predictive, to take into account : epitaxial growth, secondary nucleation events and 3D growth inside the weld pool.

Jan 1, 2015

By S. Hume, J. Shepherd

Meso-2,3-dimercaptosuccinic acid(DMSA) was studied as an additive for thiosulfate leaching of gold. DMSA was added to solutionscomposed of either sodium thiosulfate or calcium thiosulfate and the solutions were tested for their ability to leach pure gold samples as well as a calcined gold ore from Barrick Gold Corp. Results showed prolonged leaching of pure gold samples when DMSA was added at a concentration of 5µM; however, higher concentrations were shown to inhibit leaching. Differential capacitance measurements of the interface indicated that DMSA adsorbed as a defective monolayer on the surface of gold at low concentrations and formed a more compact monolayer with increased concentration. It is proposed that a concentration of 5µM DMSA produces a defectivemonolayer on the surface that still allowsthe transport of oxidants to the underling metal while inhibiting the formation of polysulfide passive layers that arise fromdecomposed thiosulfate.The 5µM DMSA/CaS2O3 system was also studied using calcined ore. Results showed that the initial leaching rates in the presence of DMSA are lower than those obtained in thiosulfate alone. However, after 10h, prolonged leaching is again observed when DMSA is included.

Jan 1, 2015

By Eduardo R. Rodrigues, Ankur Narang, Roberto Federico Ausas, U. T. Mello, Jose Maria Segura Serra, M. R. Lakshmikantha, Ignacio Carol, Kamal C. Das

"Modeling of big faults or weak planes of strong and weak discontinuities is of major importance to assess the Geomechanical behaviour of mining/civil tunnel, reservoirs etc. For modelling fractures in Geomechanics, prior art has been limited to Interface Elements which suffer from numerical instability and where faults are required to be aligned with element edges. In this paper, we consider comparative study on finite elements for capturing strong discontinuities by means of elemental (EFEM) and nodal enrichments (XFEM) for Geomechanical applications. For general fracture scenarios, Oliver et al. (2008) have demonstrated advantages of EFEM over XFEM for including: (a) ease of modeling in any standard finite element code due to the possibility of static condensation, (b) higher accuracy in some cases for coarse meshes, and, (c) a reduced computational cost. However, there has been no work that considers cohesive fractures in Geomechanics. We present a numerical analysis based on a linear constitutive model and linear triangular elements for the bulk and a linear constitutive behaviour for the fault for a representative set of fault planes in a circular tunnel made in rock mass. In the numerical examples we consider both well-traced and bad-traced meshes. We focus on traction profile analysis for both EFEM and XFEM, since that is crucial to understand the cohesive fracture behaviour specially rock joint. Therefore in each case, shear, normal and stress ratio are compared across the two methods along the fault plane. This is the first such work that compares XFEM and EFEM behaviour for Geomechanics problems.For the considered class of problems and the sharp penalization approach without regularizations adopted, it can be observed that accuracy and robustness of EFEM may strongly depend on the fault orientation with respect to the element edges, while, XFEM is independent of fault alignment with element edges. It has been also observed that, with mesh refinement model, stress oscillation completely removed with XFEM however EFEM fails to provide oscillation free results with finer mesh in case bad-traced model. We also performed error analysis and found that in case of bad-traced mesh the average error in the XFEM is 84% smaller than of EFEM and for XFEM the error goes to zero with increasing mesh resolution, while for EFEM the error increases with mesh resolution. Thus, we experimentally demonstrate that, XFEM performs better than EFEM in terms of accuracy and rate of convergence with marginal increase in computational cost. This work hence provides novel insights on the application of XFEM and EFEM in Geomechanics."

Jan 1, 2015

By A. L. McAllister

"MASSIVE sulphide deposits are found in two areas of New Brunswick, the St. Stephen area and the Bathurst-Newcastle area. In both, the geology in the immediate vicinity of the sulphide bodies is largely inferred from drilling results as outcrop is not plentiful and is, in fact, almost lacking in most places. With few exceptions these deposits have not been explored by underground methods. Consequently much of the. detail on the geology will only become known over a period of years as economic conditions make mining feasible.Much of the information contained in this paper has been supplied directly by company geologists. As a result of the number of contributors, some confusion of nomenclature bas to be anticipated. Cross-sections and plans of the individual deposits are, in most cases, as supplied by the companies concerned. Most of the interpretations are the responsibility of the author."

Jan 1, 1960

By R. Plassart, F. Laigle

"As a powerhouse, a transformer or a valve chamber, large underground caverns are a major element of hydropower plant. On the contrary to galleries and shafts which are linear and long underground structures, large caverns are designed with often complex geometries and large spans. Moreover, as these caverns are generally located on the foot of the hydraulic scheme, the high overburden is often responsible of a high stress state. Thanks to current experiences in France and around the world, the Hydro Engineering Centre (CIH) of EDF has defined great principles in the design of caverns leading to a more general methodology. The project of Tehri in India is an example of difficult ground, with in the same time a high overburden, a ductile material and an important schistosity. These physical realities are attempted to be approached in numerical modelling thanks to a constitutive law with softening behaviour and an oriented criterion integrated in the continuum model. As a result, a flexible support is advised, based on a high density bolt system and a thin lay of shotcrete. This methodology has been developed in the case of Gilboa in Israel, except the schistosity which has not been observed in situ. At last, the example of Gavet (France) illustrates a discontinuous case of numerical modelling for a good quality but fractured rock mass.PRINCIPES ET METHODES DE CONCEPTION DE GRANDES CAVERNESHYDROELECTRIQUES SOUTERRAINESRESUME Les grandes cavernes souterraines abritant les turbines, les transformateurs et certaines vannes sont des ouvrages majeurs dans les aménagements hydroélectriques. A la différence des galeries et des puits qui présentent de longs linéaires, les grandes cavernes sont des structures à la géométrie souvent complexe et avec des portées conséquentes. De plus, ces cavernes étant généralement situées en pied du circuit hydraulique, la grande couverture rocheuse peut se traduire par un état de contraintes important. Forte de ses expériences récentes en France et dans le monde, le Centre d’Ingénierie Hydraulique d’EDF a identifié de grands principes de conception des cavernes permettant l’élaboration d’une méthodologie plus générale. Le projet de Tehri en Inde est un exemple de terrain difficile, présentant à la fois une forte couverture, un matériau ductile et une schistosité marquée. Ces réalités physiques sont approchées au mieux grâce à la prise en compte dans les modélisations numériques d’une loi de comportement radoucissante avec un critère orienté intégré dans un modèle continu. Les résultats ont conduit à privilégier un soutènement souple basé sur un boulonnage systématique relativement dense associé à une fine couche de béton projeté. Cette méthodologie a ensuite été reprise pour le projet de Gilboa en Israël, exception faite de la schistosité puisque non observée sur site. L’exemple de Gavet (France) enfin permet d’illustrer un cas de modélisation numérique discontinue d’un massif rocheux de bonne qualité mais fracturé."

Jan 1, 2015

By M. Beech-Jones

The increased emphasis on the efficient utilization of capital and mineral resources has led to several new advances in the science of mineral separation. One example of a recent development is the application of high-capacity high-intensity wet magnetic separators to fine hematit e recovery by a leading Canadian iron ore producer. The iron ore recovery feasibilit , flow-sheet development, circuit operation and metallurgical performance are reviewed.

Jan 1, 1979

By Liguang Wang

The froth phase in flotation has received much less attention than the pulp phase despite the fact that froth stability plays an important role in determining flotation performance. Froth stability is largely determined by the stability of thin foam films, which in turn has a strong correlation with the critical rupture thickness (Hcr) of the films. In the present work, a new approach to predicting the Hcr values of thin foam films in flotation froth phase was proposed and examined. The Hcr values were calculated using an advanced capillary wave model with input parameters being surface tension, film radius, capillary suction pressure, and intersurface force. The intersurface force was estimated by using the Stefan-Reynolds lubrication approximation to fit the measured thinning rates of single foam films formed in a Scheludko ring cell, where the film radii were less than 50 microns and were kept constant during the film-thinning process. A comparison between the predicted and experimental Hcr values was made for the films with the use of sodium chloride as background electrolyte and in the presence of various frothing reagents such as methyl isobutyl carbinol (MIBC), polypropylene glycol with an average molecular weight of 400 (PPG400), and sodium dodecyl sulphate (SDS), at different concentrations and film radii. It was found that the model correctly predicted the trends of Hcr-versus-concentration and Hcr-versus-film radius curves. Moreover, the predicted Hcr values matched well with the experimental ones of the foam films containing either SDS or PPG400. For the foam films containing MIBC, however, the model overpredicted the Hcr values. The reason for this discrepancy was discussed.

Jan 1, 2016

By S. Zador

"IntroductionIn the past decade, metallurgical and mining companies have shown an increased interest in the licensing of technology. When licensing technology, it is usually to the benefit of the parties, to have at least some of the technology to be licensed protected by a patent.This paper is intended to bridge the gap between the engineer in the field of mining, metallurgy and mineral processing who is interested in exploiting an invention commercially, and the patent agent or intellectual property lawyer whom he/she might retain to prepare a patent application and then prosecute the application to obtain a granted patent. It is also intended to encourage the inventor or a small business concern to consider the value of patents in the sale and licensing of technology. The lawyer may subsequently advise and assist the inventor in licensing his/her invention.A brief outline of some of the basic features of the patent system follows. The nature of the information, which the patent professional requires from the inventor to enable him/her to draft a patent application, will also be considered in general terms. Furthermore, various types of licenses which may be drawn up between a licensor of specific technical information and a licensee, will be listed and briefly discussed. No attempt, however, will be made to give a comprehensive and detailed account of the above aspects; the interested reader should consult legal publication and reference books, and patent professionals for further specific information.A granted patent is a document which describes an invention and how to practise it. The claims of the granted patent, figuratively speaking, fence off the intellectual property the inventor regards as his invention. The Commissioner of Patents, representing the Government, grants to the inventor or his assignee the exclusive right of making, constructing and using the invention, and selling it to others to be used, for a limited period of time, in exchange for disclosing the invention to the public. Thus, a patent prevents others from practising the claimed invention but it does not, necessarily, bestow the right to the patentee to practise his own invention. The term of a patent now in Canada and in most of the developed countries of the world, is 20 years from the date of filing the patent application. In the United States the patent term is still 17 years from the date of issuance of the patent. In Canada, the term was changed to 20 years in the new Canadian Patent Act which came into force on October 2, 1989. Any patent application filed prior to that date or granted before it, retains a 17 year life, commencing at the time of grant."

Jan 1, 1991