Search Documents

By A. G. Pathan

Rock and soil mechanics investigations were carried out in block VIII at Thar Coalfield, Pakistan. Most of the strata were mainly composed of sand, with an average content of 67.68 %. Laboratory studies of rock and soil samples from drill hole GT-01 revealed that the strata in block VIII are very weak with an average uniaxial compressive strength of 3.59 MPa, an average tensile strength of 0.68 MPa, an average Young?s Modulus value of 0.234 GPa, an average cohesion of 129.19 KPa, and an average friction angle of 55.47°. Slope stability analysis, based on a probabilistic approach, was carried out using Slide-V software. Monte Carlo simulations have been applied to investigate the probability of failure in the slopes of an open pit lignite mine in block-VIII. From the slope stability investigation, it was found that the probability of failure is 0 % at a slope angle of 16°.

Aug 1, 2013

By E. Eccleston, E. Gardner, F. Letarte, R. Schonewille

"In 2005, after nearly a decade of process development and feasibility work, the commercialization of the Falconbridge Nickel Smelting Technology (NST) began in earnest with the design and construction of a grassroots ferronickel plant at Koniambo Nickel in New Caledonia. The NST process was developed as an alternative to the conventional Rotary Kiln-Electric Furnace (RKEF) process for production of ferronickel from saprolitic nickel laterite ores. The NST process promised environmental and energy efficiency advantages over the conventional route. A key step of the NST process involves fluidized bed pre-reduction of calcined laterite ore using direct injection of pulverized coal as the reductant. Two parallel fluidized bed reduction roasters (FBRs) were installed at Koniambo Nickel, each designed for a maximum capacity of 4,200 MTPD of calcined nickel laterite ore. This paper describes the process development and scale-up of the fluidized bed pre-reduction process, the design challenges associated with the prototype commercial units, and the current status of the FBR operation at Konaimbo.INTRODUCTION In the mid-1990s, Falconbridge began to develop a new flowsheet for production of ferronickel from nickel laterite ores. The process that developed came to be known as the Falconbridge Nickel Smelting Technology (NST). The flowsheet, which is particularly appropriate for saprolitic ores, involves several major unit operations, including: drying in a hammer mill-flash dryer, calcination and preheating in a flash calciner, pre-reduction in a fluidized bed reactor, and smelting in a DC arc furnace to produce the ferronickel product. This paper focuses on the fluidized bed pre-reduction step of the process and provides an overview of the process chemistry, laboratory and pilot plant development work, scale-up and commercialization of the pre-reduction step, and the results obtained in the prototype commercial units."

Jan 1, 2017

By P. Garritsen, J .. A. Blanco, M. C. Bell

"By 1994, Inco Limited will lower sulphur dioxide emissions from the Copper Cliffsmelter by 60% to 265 000 tonnes/year, primarily through implementing two key process changes. First, new milling technology will permit economic rejection of additonal pyrrhotite prior to smelting. Second, a bulk coppernickel concentrate will be oxygen flash-smelted, thereby eliminating the existing multi-hearth roasters and reverberatory furnaces . All copper will be recovered in the matte separation plant as a nickeliferous chalcocite, and will be oxygen flash-smelted for blister production. This paper outlines the development of the project and describes the process, including the flash furnaces, new sulphuric acid plant and additional oxygen plant.IntroductionInco 's SO2 Abatement Program will lower sulphur dioxide emissions at Sudbury from the current levels of 685 000 tonnes per year to 265 000 tonnes per year by 1994 as required by Ontario' s countdown on acid rain regulations.It is the high tonnage of sulphur mined that creates the magnitude of the SO2 emission problem at Sudbury. At a production rate of 240 million pounds of nickel per year, Inco mines 12 million tonnes of ore. At 10% sulphur it mines 1.2 million tonnes per year of sulphur. If Inco did not fix any of this sulphur it would be emitting 2.4 million tonnes per year of sulphur dioxide-about as much as all other Canadian emissions. Today, however, Inco is already fixing 70% of the SO2 in ore, in several ways : mostly as sulphur in pyrrhotite rejected to tailings in the milling operations; as acid from the roasting of pyrrhotite and some nickel concentrate at the Iron Ore Recovery Plant (lORP) and some as liquid S02 from the copper flash smelting furnace. By fixing 70% of the sulphur the current allowable SO2 emission levels of 685 000 tonnes per year is met. Total sulphuric acid production is currently 450 000 tonnes per year and in fact, the 10RP operation is being continued only to maintain established acid markets.Historically emissions have been reduced from the 2 000 000 tonne per year level to the current level of 685 000 tonnes per year by rejecting pyrrhotite from the smelter feed, and 70% of the SO2 containment problem at Sudbury has already been addressed.While Inco's profits are large at current nickel prices, most people have forgotten that back in 1982 Inco was losing a million dollars a day. Inco did make a dramatic response to this economic stimulus. The Ontario Division increased productivity by 65% and lowered costs to become the lowest cost nickel producer."

Jan 1, 1990

By Masashige Makifuchi, Hiroki Kumakura, Kota Nagai, Takahiro Kikuchi

"A large amount of platinum group metals (PGM) are used in automobile catalyst. It is important to recover the metals from wasted catalyst. Nomura and Kageyama (2013) suggested recovery process that PGM oxides were absorbed to perovskite-type oxide based on LaScO3. In their process, the PGM in wasted catalyst as absorbed to the perovskite-type oxide as PGM oxide. It has potential to each element in the process if the perovskite-type oxide is selected properly. In this study, the PGM oxide absorption properties of various perovskite-type oxides are investigated to develop a new recovery and separation process. The various perovskite-type oxide were synthesized with metallic platinum, palladium, rhodium at high temperature in air atmosphere. And the PGM contents in the perovskite-type oxide after the experiment are determined by chemical analysis. Some of them have the properties to absorb specific PGM oxide selectively. In addition, in order to increase the amount of absorption of PGM oxide and composition of the perovskite-type oxide experimental temperature was investigated. Then it is also found that doping another specific element to the perovskite-type oxide is effective to increase the amount of absorption of PGM oxide. Then a new recovery process of PGM from wasted automobile catalyst, in which PGM can be separate to each element, was designed.INTRODUCTIONA large amount of Platinum (Pt), Palladium (Pd), and Rhodium (Rh) are used in automobile catalysis (Figure 1) (Platinum, 2013). Natural supplies for these metals are limited and PGM mining can detrimental environmental impact. Therefore, the recycling of PGMs from wasted automobile catalysis is very important. The Rose process (Figure 2) was developed as a process to recover PGM from wasted automobile catalysis. In this process, the automobile catalysis is first crushed mechanically, and then extracting agent, copper (Cu), and flux are melted at high temperature. The mixture separates into a metal phase, (Cu alloy containing PGM) and slag. The PGM is enriched by oxidizing. Cu to Cu oxide. The PGM are then recovered and separated to each element in a wet process. However, it is hard to dissolve the PGM with acid because they are chemically stable and strong oxidation agent such as aqua regia is used. Moreover, to separate the PGM to each individual element, a solvent extraction process is required."

Jan 1, 2016

By M. J. Bunyard, I. Mullany

"The pressures on mine operators are varied and constantly increasing, declining ore grades, more remote locations and increasing environmental concerns. The challenge facing the mining industry is to find new ways to process ores which are more efficient and less costly and to control them better. This requires a fundamental rethink in the way in which projects are developed, it is no longer good enough to just copy what has been done before. The process starts with the surfacing of the primary underlying constraints for the project and the establishment of new design principles to address these. The generation of new design criteria and processing options follows the well-established path of brainstorm, focus, brainstorm, refocus and economic evaluation. The aim is process intensification, doing more with less, as early as possible and better use of plant data. The methodology requires a complete geometallurgical understanding of the orebody to facilitate the evaluation of viable processing options. Examples of early stage processing considered are blast optimization and ore sorting to reject waste and reduce processing costs. Mine to mill integration, which starts with the optimization of blasting for separation, offers another way to significantly reduce operating costs and increase efficiencies.VALUE MODEL The mining industry has, over the past decade, experienced an unprecedented cycle of increased commodity prices and investments in new mining and processing capacity followed by a market collapse and fall in prices and confidence. Whilst there are now some signs of a return to investment in new capacity, the metals and mining industry is still wrestling with eroding margins and investor demand that companies achieve the full value of their assets. Metals and mining companies must work on all available levers to deflate their costs back to more manageable levels and capture the full value for their products. Levers include optimizing external spending, re-thinking make vs buy trade-offs, debottlenecking, improving availability and operating time of key equipment, more accurate and agile planning processes, value-in-use optimization, and tighter performance management. Figure 1 is a diagrammatic representation of a company’s value model. The three goals of a successful mining enterprise are social acceptance, environmental acceptance and sound financial returns to shareholders. Some of the KPI’s used to measure the success or not of achieving these goals are shown in the translation layer."

Jan 1, 2017

By A. Haque

"This paper describes an improved formulation of an analytical shear strength model developed by Haque & Kodikara (2012) by incorporating the failure of regular concrete/rock joints subjected to CNS condition. Sokolovskii’s analytical solutions developed for failure stress of slopes have been found to be effective in this regard. The analytical models have been validated for predicting the shear behaviour of concrete/rock joints subjected to various CNS loading conditions. The model has been found to accurately predict the dilation, normal stress and shear stress behaviour for a regular triangular saw-tooth joint up to the peak shear stress. Moreover, the peak shear stresses of concrete-rock joints with asperity angles ranging from 5 to 27.5o compared reasonably well with the available laboratory test results.INTRODUCTIONA new shear strength model for elastic regular triangular concrete/rock joints loaded under Constant Normal Stiffness (CNS) boundary condition has been developed by Haque & Kodikara (2012). The salient feature of this model is its capability of accurately estimating the normal and shear stresses of joints with shear displacements under CNS condition by incorporating the elastic deformation of asperities. However, the shear strength model of Haque & Kodikara (2012) for the elastic asperities cannot be directly employed to predict the peak shear stress of a joint experiencing plasticity under applied loads. Therefore, the model inevitability requires articulation of an appropriate shear failure criterion simulating the boundary conditions of the loaded asperity to predict the peak shear stress and corresponding normal stress and dilation behaviour of concrete/rock joints. Sokolovskii (1960) developed a set of analytical solutions for failure stress of slopes comprising c-??soils, which can be exploited effectively to simulate the failure condition as encountered for loaded regular triangular concrete/rock joints (Seidel & Haberfield, 2002)."

Jan 1, 2015

By C. Edwards

ABSTRACT: Milling operations in northern Saskatchewan’s Athabasca Basin have produced uranium continuously since 1975. During that period, the Athabasca Basin has been one of the world’s premier uranium camps, yielding more than 660 million lb (299,370,964 kg) of U3O8. In this paper, the author describes former and current milling operations and discusses why and how the milling process has changed and developed over the past 35 years. The author’s considerations for the future of uranium extraction in the Athabasca Basin conclude the paper.

Jan 1, 2012

By G. Forté, R. Girard

The Alcan Bayer Process Experimental Centre (BEC) is an essential development tool for the Bauxite & Alumina researchers at the Alcan Arvida Research and Development Centre in Jonquiere, Quebec. Between the laboratory tests and the industrial prototypes or the industrial applications, the BEC is a key element for technology transfers. The Bayer process is the extraction of aluminium oxide (or alumina) from the bauxite ore. The Bayer Experimental Centre's history and flowsheet are presented. The major pieces of equipment are described. Safety and design considerations are presented. Finally, examples of applications, double digestion and pressure decantation, are briefly described.

Jan 1, 2004

By A. Tikhonov, D. Kipper, V. Korovin, A. Olifirenko, Yu. Shestak

The present paper deals with vanadium and molybdenum sorption from industrial wastes and intermediate processing products using Cybber macroporous strong- and weak-base anionites. Vanadium and molybdenum recovery by Cybber anion-exchange resins as well as desorption processes were studied in static and dynamic modes; their efficiency was demonstrated for that purpose. The results of the work may be used to design technologies for complex processing of both ores and industrial wastes containing vanadium and molybdenum.

Jan 1, 2011

In the present work, the effect of pH, non-ionic polyacrylamide flocculant and anionic polyphosphate on rheology and settling behaviour of colloidal TiO2 suspensions (15 ? 50 wt% solid) is investigated. Maximum particle aggregation, reflecting in the highest suspension settling rate and maximum shear yield stress was achieved at pH 7.2, the isoelectric point (iep), consistent with DLVO expectation. However, the maximum aggregation condition at the iep also resulted in the poorest suspension consolidation behaviour. Significantly enhanced consolidation was achieved for a more dispersed suspension at pH values away from the iep but at reduced settling rate. Thus, when pH alone is used to control conditions which facilitate strong interparticle attraction, a high settling behaviour which is not conducive to compact consolidation results. Improved suspension consolidation may be achieved at the iep via anionic polyphosphate addition which leads to attenuation of the strongly attractive van der Waals forces and emergence of "soft" repulsion due to weak inter-particle electro-steric forces. The weak repulsion act to lubricate particles involved in the hydrodynamic interactions which controls the compressibility of the sediment bed, allowing a compact consolidation of solids to be obtained. Alternatively, non-ionic polyacrylamide homo-polymer (Magnafloc 333) was fairly effective in flocculating titanium dioxide suspensions leading to high settling rate and acceptable pulp consolidation at the iep.

Jan 1, 2006

By E. Ghali, A. D. Bas

There is a lack of electrochemical studies of oxidized gold ores since the majority of previous studies were conducted with sulphidic gold ores. In this study, the influence of agitation and iron oxide minerals, i.e. magnetite, hematite, and maghemite on gold leaching was investigated by means of galvanic and passivation phenomena. Cyclic voltammetry studies of Roasted Gold Ore (RGO) in de-aerated electrolyte have shown one oxidation and one reduction reaction while three oxidation and one reduction peaks were observed with gold electrode. Galvanic coupling results by Zero Resistance Ammeter (ZRA) mode indicated that magnetite showed a negative effect on gold dissolution while maghemite and hematite showed a positive effect, relatively, as a result of higher galvanic corrosion rates. Generally, gold dissolution was found to increase in the initial 15 minutes. Increasing agitation speed from 100 to 400 rpm resulted in higher galvanic corrosion rates for RGO, magnetite, and maghemite electrodes, while 250 rpm was found to be optimum for hematite electrode. Passive products such as silver and iron-oxide were identified by XPS and SEM-EDS analysis, respectively.

Jan 1, 2015

By P. Abachi

Cemented carbides or hard metals that generally consist of hard tungsten carbide and a tough metal binder such as cobalt are important in many segments of the world economy, ranging from automobile related components to machining, cutting, and drilling tools. For metal cutting operations such as turning and milling, replaceable cemented carbide inserts are frequently used. The exposure of inserts to very severe conditions (e.g. temperatures as high as 1000°C) in combination with very high loads, limits their lifetime. When the tools and components are scrapped, they are collected with a view to recovering the tungsten carbide and cobalt due to both their environmental aspects and their strategic importance. In this work, a selective electrolysis process was used for recovery of WC powder particles from cemented carbide scraps. The WC-10Co and WC-10Co-VC up to 3 wt.% VC was produced using powder metallurgy route. The mean particle size of WC, Co and VC were selected as 2.5, l.5 and 2.2 µm respectively. Referring to electrochemical curves of WC-10Co cemented carbides in hydrochloric acid solutions with different concentrations, the recovery rate was enhanced in IN acid. Therefore, this solution was selected for recycling of all samples. The surfaces of as-produced and corroded specimens were investigated using a scanning electron microscopy (SEM). Detection of corrosion products was provided by energy dispersive spectrometry (EDS). According to results, the selective electrolysis process could be useful in the recycling of scrap carbide materials, although more studies should be undertaken on economical aspects of the process and the quality of samples produced using recovered powders.

Jan 1, 2005

By H. Sato, Y. Sato, T. Ooishi, K. Sakamoto

"Sumitomo Metal Mining Co., Ltd.(SMM)'s Niihama Nickel Refinery(NNR) produces high quality Nickel cathode, Cobaltcathode and other by-products using hydrometallurgical refining process called “MCLE”(Matte Chlorine Leach and Electro-Winning). In 2005,NNR started to use nickel and cobalt mixed sulfide (MS) produced by one of the SMM’s subsidiaries Coral Bay Nickel Corporation(CBNC)’s HPAL plant in Philippines, although its main and the only raw material until then was nickel matte. With start-up of the second HPAL plant at Taganito in 2013, NNR expanded its production capacity of nickel cathode from 41,000 to 65,000 tpa and finally achieved its target in 2015 by producing 65,980 tpa. SMM developed the technologies to improve poor reactivity of MS and installed new facilities to cope with increased Cobalt and Sulfur production at that time. This paper describes the technical approach to increase MS treatment with high efficiency.INTRODUCTIONThe Sumitomo Metal Mining Co., Ltd.(SMM)Niihama Nickel Refinery(NNR) produces Nickel cathode, Cobalt cathode and other by-products using Matte Chlorine Leach and Electro-Winning (MCLE) process technology. SMM uses nickel matte and nickel & cobalt mixed sulfide (MS) as raw materials for the MCLE process. Table 1 shows typical composition of these raw materials. Nickel matte had been only raw material until 2005, and with start-up of Coral Bay Nickel Corporation (CBNC) operation in the Republic of the Philippines, MS became major part of it. In 2009, when CBNC doubled its production capacity, NNR also expanded its plant capacity of electrolytic nickel from 36ktpa to 41ktpa, keeping an eye on the possibility of 65ktpa with oncoming SMM’s second HPAL in Philippines. Poor reactivity of MS was the prime concern at that time because our intention was to increase production with MS. Nickel extraction rate deteriorated with increasing usage ratio of MS in raw materials. To keep high nickel extraction rate under high ratio of MS, NNR developed a new leaching technology. Another concern arising from treatment of MS was Cobalt and Sulfur contents that are much more than those of nickel matte as shown in Table 1.NNR introduced new technology of solvent extraction process as to Co/Ni separation process in order to keep cost competitiveness instead of the conventional cobalt oxidation–neutralizing method. As to sulfur products, new sulfur productive facility was installed to improve the exposure to sulfur dust and the hot working conditions for workers. As a result of process development and installation of new facilities against the problem with MSusage,65 ktpa production was achieved in 2015."

Jan 1, 2017

By G. W. Davies

"IntroductionThe development of British Columbia's northeast coal deposits, represents the single biggest industrial undertaking in British Columbia's history.As a result of this development, several thousand jobs were created, hundreds of millions of dollars in new tax revenue and billions of dollars in new foreign exchange began flowing into Canada.The Northeast Coal Development began in 1981 with the signing of sales contracts to ship a total of 6.5 million tonnes of metallurgical and additional quantities of thermal coal annually to Japan over a 15-year period. The current long-term agreements contain provisions for extension to 20 years.The sales contracts with a group of Japanese steel mills were signed by two Vancouver-based mining companies, Quintette Coal Limited and Teck Corporation. The agreements followed years of exploration and negotiation beginning in 1968.The first shipment of coal from Quintette and Teck's Bullrnoose Mine was transported by BC Rail and Canadian National Railways to the Ridley Island coal port in the fall of 1983."

Jan 1, 1992

By Stephen Hardcastle

Presentation Outline ? Introduction ? Mine Ventilation Facts ? Ventilation-on-demand (VOD) ? Sensors/Controls ? Continuing Work ? Conclusions ? Mine ventilation engineering practices were published in 1556 in Agricola?s De Re Metallica (wind sails, bellows, etc.) That was then? This is today? Large fan installations handling >1M cfm

Nov 1, 2011

By T. H. Patching, M. W. Mikhail

"Data from a standardized procedure for measuring methane desorption rates from samples of Western Canadian coals gave a good correlation (0.994) with the percentage of fines (-0.6 mm) found in the corresponding run-of-mine coal. The correlation was independent of the mining method and the top size of the samples. It is suggested that both methane desorption rate and the production of fine coal sizes are functions of the fissuration of the coal being mined.This relationship, in conjunction with established data of degradation by unit process equipment, may be useful in predicting the amount of fines that will be produced from new seams of coal and by planned new washeries. It also could be a valuable guide in modifying existing washery processes to minimize production of fines."

Jan 1, 1980

By E. C. Payne

"IntroductionTHE SMALLER industrial and commercial steam generating plants in the United States are suffering from an ‘engineering deficiency' which, if allowed to continue, will probably result in the extinction of the species• that now burn •approximately 75 million tons of coal. We will classify as 'small' those plants which should require not more than one operating man per shift, including those in which as little .as thirty minutes per day should be adequate for .all service attention. These are the small steam plants that need the most, and get the least, expert attention for fuel :planning, equipment selection, design layout, .and proper operating technique. Dissatisfaction with bituminous coal is usually caused by one or more preventable weaknesses such as excessive or burdensome labour •for firing, .coal or ash handling and manual operation, smoke and fly ash emission above nuisance levels:, high maintenance and premium coal application for acceptable operation, and .finally, overall steam costs which are not .competitive. These 'deficiencies', so .common in the small coal-fired steam plants, can be readily eliminated by competent engineering and modern equipment with automatic controls."

Jan 1, 1953

By J. N. Van der Merwe, M. Mathey

"We present an analysis of the mechanical properties of coal specimens from various coalfields and seams in South Africa. Our database comprises of 1800 test results from uniaxial and triaxial compression tests, as well as indirect tensile strength tests, which we collected from the various mining houses and research agencies in the country. We inspected the database for possible errors and present a brief description of the verification procedure in the paper.In the analysis, we reveal that the collected samples of strength and elastic properties of South African coals can be represented by single lognormal or normal distributions with only few outliers. This finding indicates that the samples realistically approximate the population of mechanical coal properties in the country and may suggest that the properties are randomly distributed. Significant coalfield- or seamspecific trends for the mechanical properties of coal are not clearly discernible from our data.Typical coefficients of variation for the individual mechanical properties range between 25-50 % on a country-wide and seam-specific level of analysis. Average uniaxial compressive strength values, however, are closely clustered for all seams. A comparison with data available from international coal strength studies show the distinct difference between South African coals and seams in countries of the Northern Hemisphere, where differences in the average coal seam strength are more pronounced.We observe that the number of specimens whose failure mode is influenced by the presence of natural discontinuities reduces drastically with the application of very small confining pressures to the specimens. Further, the strength-reducing influence of discontinuities diminishes with increasing confining pressures."

Jan 1, 2015

By D. Marcotte

The Rock Quality Designation (RQD) is a standard scalar measure of rock quality used in common rock mass classification systems (e.g. RMR, Q system). RQD is measured along diamond drill holes. RQD interpolation between holes is nontrivial. Despite the inherent limitations of drill hole data and the local complexities of structural geology, it is often the only information available for mining and major civil engineering projects. Therefore, maximizing the usefulness of this data is warranted. We derive a correction for directional effects that help reduce the bias and improve the accuracy of the estimations. The correction is derived with the aid of numerous simulations. It relies on simple information, the angle between the joint normals and the borehole axis (JO). A reference direction is identified as the borehole direction with smallest JO. A multiple linear regression model based on JO statistics in the various boreholes defines the correction model. The corrected RQD values are then interpolated. It is shown the method enables reducing the bias on RQD estimation by 50% and improves the accuracy of the estimates by 30%. The corrected RQD values show stronger spatial continuity than the raw values. The benefits of estimating the RQD indirectly by using joint frequency measures are also assessed.

May 1, 2003

By Zhong Zhang, Xijia Wu, Prakash C. Patnaik

"The integrated vehicle health management (IVHM) aims to provide life cycle management decisions for military platforms and their propulsion systems with reduced life cycle cost and increased operational readiness and safety. Among all the issues of IVHM, understanding the physics of failure and predicting lifetimes of the critical components are at the core: the decision makers have to know when and how components may fail in order to plan ahead. The difficulties to tackle failure problems lie in determining the material response to cyclic and dwell loading in a hot and/or corrosive environment, which all combined to induce multiple deformation and damage mechanisms, resulting in mix-mode failures. Decisions on component replacement (material substitution) and mission planning must be based on quantitative knowledge of the failure physics to mitigating the risk. This paper addresses the critical failure issues including creep, low cycle fatigue (LCF), thermomechanical fatigue (TMF); and presents a mechanism-based approach to life prediction. The mechanism-based approach, by its physics, is widely applicable over the entire operational spectrum of both structures and engines, and therefore is suitable for IVHM purposes."

Jan 1, 2015