Search Documents

By C. E. Lancelle, J. T. Volk, H. F. Wang, D. Fratta

"The Main Injector Neutrino Oscillation Search (MINOS) Near Detector Hall at Fermilab and the Lafarge – Conco Mine are located approximately 100 meters underground in the Galena-Platteville dolomite just below its contact with the overlying Maquoketa shale in Northeastern Illinois, USA. A new cavern was excavated adjacent to the MINOS Near Detector Hall at Fermilab to house the near detector for the Off-axis Neutrino Appearance Experiment (NOvA) program. During this excavation approximately 1150 cubic meters of shale rock were removed. Tiltmeter arrays consisting of a series of hydrostatic leveling sensors (HLS), which are spaced regularly over a total distance of 50-to-100 meters, were used to monitor subsurface deformations. The tiltmeter response in the MINOS Near Detector Hall due to the NOvA cavern excavation is approximately thirteen times the estimated response based on using laboratorydetermined properties. The discrepancy between modeled and measured tilt is likely due to differences in Young’s Modulus in the rock mass versus in a small laboratory sample. Amplitudes of measured solid earth tides differ from the amplitudes of theoretical solid earth tides by up to 40 percent for both arrays. This is likely due to a local heterogeneity or discontinuity.INTRODUCTIONLong baseline tiltmeters have been used to record small earth movements since the early 1900s. One of the first studies using long baseline tiltmeters to measure earth tides was published by Michelson (1914). He used a leveled 152-meter long, 0.15-meter diameter tube half-filled with water connecting two concrete-lined pits. The pipe was trenched 1.75 meters underground in Williams Bay, Wisconsin in a sandy-clay soil. Initially only an east-west line was used, though a north-south line was added after it was seen that viable results were obtained. Measurements were made by hand either hourly or once every two hours depending on the time of day. When compared to 0.7 times the calculated earth tides, the tiltmeter signal matched almost exactly. This excellent result began the use of long baseline tiltmeters to measure small earth movements."

Jan 1, 2015

By W. A. Gow, V. F. Harrison, H. H. Mccreedy

A semi-continuous bench-scale, countercurrent-decantation system, in which the ore was moved countercurrently to the flow of leaching solution, was used to conduct acid-leaching tests on uranium ore with the aid of bacteria. This method, which involved a low degree of agitation, was successfully applied to extract uranium in practical amounts and at practical rates. The acidity of the leaching solution was the main variable investigated in the bench-scale tests done at the Mines Branch, Ottawa. Over 90 11er cent of the uranium was extracted in a six-stage system. The results suggest that this technique could be ap-plied in the utilization of bacterial oxidation and leaching as a method for treating Elliot Lake uranium ore.

Jan 1, 1969

By D. R. E. Whitmore, J. M. Harrison

There are five logical stages in the search for orebodies in virgin territory, namely: (1) reconnaissance inventory of geology, and related investigations; (2) development of broad concepts as a basis for selecting regions of potential mineral deposits; (3) assessment of criteria leading to specific localities within these regions; (4) geo-physical and geochemical studies that will delineate small anomalous areas; and (5) stripping, drilling or other means of locating ore. In addition, the development of new means of extracting mineral resources and the finding of new uses play a vital role in our mineral industry. The continued growth of this industry will be largely governed by our ability to develop or to adapt new concepts and techniques, and to produce a greater number of scientists and engineers. It should always be remembered that more than one-third of Canada's exports are dependent upon our ability to find, develop and economic-ally exploit new orebodies.

Jan 1, 1967

By James D. Bliss, David M. Sutphin

"On the basis of differences derived from genetic, descriptive, and grade-tonnage data, graphite deposits are classified here into three deposit types: disseminated flake, amorphous (microcrystalline), or graphite veins. Descriptive models have been constructed for each of these deposit types, and grade-tonnage models are constructed for disseminated flake and amorphous deposit types. Grade and tonnage data are used also to construct grade-tonnage models that assist in predicting the size and grade of undiscovered graphite deposits. The median tonnage and carbon grade of disseminated flake deposits are 240 000 tonnes and 9% carbon and for amorphous deposits, 130 000 tonnes and 40% carbon. The differences in grade between disseminated flake and amorphous deposit types are statistically significant, whereas the differences in amount of contained carbon are not .IntroductionIndustrial minerals, including mineral construction materials such as sand, gravel, and crushed stone, have historically exceeded metals in global production value. Today, industrial minerals are being used in new and sophisticated ways in response to the late 1980s emerging information- and service-based economies' requirements for less metal and more industrial minerals . Natural graphite is an example of one such mine ral that has been known since ancient times, and is now finding new applications. Graphite was first used as an industrial mineral in Bavaria in 1400 A.D. where it was an important component of crucibles. Traditionally, natural graphite has been used in heavy industries. New applications, such as development of carbon-magnesite bricks a decade ago and the current advancement of alumina/graphite refractories, are increasing its graphite use. Other new uses for natural graphite, such as the use of graphite powder as a thermal blanket for the continuous casting o f steel (Northern Miner, 1987) and the addition of expanded graphite to polyurethane foam where it acts as a flame retardant (Industrial Minerals, 1987), are increasing the demand for this mineral. To meet future demand for graphite and other industrial minerals, knowledge of the characteristics of the deposit types in which they are found is important. A further look at the deposit types for graphite and at construction of descriptive and grade-tonnage models is warranted .The graphite industry recognizes three basic types of graphite , distinguished primarily on the basis of grain size: crystalline flake, lump and chip, and amorphous. These naturally occurring forms of graphite are products of metamorphism and are found in schists of various types, gneisses, and marbles. Temperatures of at [east 400°C are thought to be required for graphite formation (Landis, 1971). Synthetic graphite, also known as artificial or manufactured graphite, is a man-made carbon product and offers higher purity and lower crystallinity than natural graphite. Several authors have written about graphite's unique physical and chemical properties and the uses for individual types of graphite (Krauss et 01., 1988; Graffin, 1983; and Harben and Bate s, 1984)."

Jan 1, 1990

By M. A. Perras, H. A. Kasani, G. Walton

The development of an underground repository for the storage of spent nuclear fuel relies on a multi-barrier system to isolate the used fuel from the environment – ultimately, the biosphere. These barriers include engineered copper and steal canisters, dense bentonite, and the natural rock as well. In order to reduce the potential flow pathway along the excavation induced damage zone, various slots perpendicular to the excavation axis have been proposed. These slots are called cut-off seals and generally are filled with bentonite as it has high swelling potential and very low permeability. Many different geometries have been proposed, but clear guidelines on the selection of the optimum geometry have yet to be developed. In order to assess the optimum geometry, three shapes have been selected for this numerical study, including a trapezoid, a triangle, and a thin rectangular slot. The cut-offs were modelled for a conceptual shaft constructed in the Queenston Formation from Ontario over a stress to strength ratio that has been found at many underground research laboratories. It was found that the excavation of a triangular and thin slot cut-off had the smallest increase in the damage as quantified based on the extensile volumetric strain within the plastic yield zone. Both shapes showed an increase in the damaged zone by 13 cm at a stress to strength ratio of 2.75. The trapezoidal cut-off damage zone increased by 20 cm at the same stress to strength ratio. Further study is required to better define the optimum cut-off shape for wider variety of conditions and other geological formations.

Jan 1, 2020

By T. R. Eger

Miners can be exposed to whole-body vibration (WBV), when sitting or standing to operate mobile equipment. In order to prevent vibration-induced injury it is important to understand how miners can be exposed to vibration, the health risks associated with vibration exposure, methods to evaluate vibration exposure, and strategies to reduce vibration exposure. WBV exposure typically occurs when operating mobile equipment, such as a load-haul-dump vehicle, haulage truck, or dozer. The probability of health effects such as low back pain, neck pain, headaches, and gastrointestinal track problems occurring from daily vibration exposure can be determined based on criterion values published in ISO 2631-1 and EU Directive 2002/44/EC. A special case of WBV termed foot-transmitted vibration (FTV) occurs when a miner is exposed to vibration that travels through the feet. FTV typically occurs when standing on vibrating surfaces associated with the operation of locomotives, jumbo drills, bolters, or raise platforms; however, there is no set standard to evaluate health effects associated with FTV. Recent medical evidence confirms workers exposed to FTV can develop cold induced blanching of the toes, in addition to numbness and tingling in the feet and toes. In order to reduce the risk of adverse health effects from exposure to vibration, the hierarchy of controls (elimination; substitution; engineering; administration; and personal protective equipment) should be followed. Best practices should be used to minimize vibration exposure through equipment purchases (i.e. vehicles with lower vibration emissions and seats that attenuate vibration), reduced driving speeds, and improved road maintenance for example. The elimination of other risk factors, which increase injury risk when combined with WBV exposure, such as awkward working postures, should also be eliminated. Very little is known about FTV exposure therefore further research is required in order to develop exposure standards and identify prevention strategies.

Aug 1, 2013

By S. D. F. Rocha1, L. Katsarou, G. P. Demopoulos

"Crystalline scorodite (FeAsO4·2H2O) has been pointed out as the most stable compound to immobilize arsenic for disposal due to its good stability performance according to EPA’s TCLP test. However, in anaerobic conditions, arsenic releasing is increased to undesired levels due to scorodite reductive break down, in eh <100 mV at 5.5< pH <7 which causes contamination of groundwater. In this work, the concept of encapsulation by controlled deposition of mineral coatings immune to pH or redox potential variations is presented. Aluminum and calcium phosphates were evaluated as coatings and the release of arsenic from scorodite previously coated with phosphates was substantially decreased when compared to the VALUES (obtained from crude scorodite, both in oxic and anoxic conditions. INTRODUCTIONThe widely acknowledged hazardous properties of arsenic as a soil and natural water contaminant and its adverse health effects when present in drinking water have led to very strict environmental regulations (Mandal & Suzuki, 2002) aiming at the drastic reduction of the presence of arsenic in the effluents of the mining and metallurgical industries.In Canada, the Metal Mining Effluent Regulations (Government of Canada, 2002) dictate that the maximum monthly mean concentration in tailings for arsenic must be lower than 0.5 mg/L. At the same time the new Environmental Protection Agency’s (EPA) standard for drinking water foresees concentrations of arsenic less than 0.01 mg/L, which means that the leachability limit for the industrial waste is set at 1 mg/L arsenic (EPA, 1994; Le Berre et. al, 2007). One of the preoccupations of the mining and metallurgical industries is directed to the elimination of arsenic presence in all its effluents, especially since arsenic is commonly found in many ores mainly in the form of oxides and sulphides. After processing of arsenic-containing ores and concentrates, arsenic can be present either in solid residues and tailings, liquid effluents or in flue dusts. Several of these forms of arsenic waste materials are soluble and therefore may cause the contamination of ground water, if disposed of without further treatment."

Jan 1, 2012

By X. Wu

Tunnel Boring Machines (TBMs) are widely used for tunneling in urban areas because of their high advance rate, precise as-built profile and minimal impact to buildings and traffic on the ground. For a tunnel built by a TBM, there are strict requirements on alignment control and safety. To meet these requirements, it is important to monitor the position of the TBM. In the current practice, the TBM position data, including advance distance and line and level deviations, are reported manually to the managers on a daily basis. To interpret and analyze the position data, the managers also need to refer to various construction drawings. This practice is untimely, inefficient, and error prone for decision making. To improve the current practice, an automatic approach for real-time as-built tunnel product modeling and visualization is proposed, based on TBM position and orientation data autonomously sourced from the Virtual Laser Target Board (VLTB) TBM Guidance System developed at University of Alberta. Related information of the tunnel project, such as the as-designed alignment, soil layers, the ground, existing utility lines, is also visualized together with the model of the as-built tunnel. The modeling algorithm is presented step by step. Its application in a real-life drainage tunnel project is discussed and limitations are also identified.

Aug 1, 2013

By P. D. Barrette

This paper deals with the flow of granular materials in bins. A hybrid Lagrangian-Eulerian numerical model is introduced. The model is based on Particle-In-Cell (PIC) advection, and continuum equations describing a Mohr-Coulomb criterion. Experiments were conducted to test and verify the performance of the numerical model. Tests were done using three types of particles. Measurements of material properties and flow rates were carried out. Video records were also obtained and used to examine flow patterns. The results indicate that the numerical simulations produce deformation patterns and flow rates which are in good agreement with the experimental observations.

May 1, 2007

By A. Singh

Deformation structures after tensile and compression tests on Mg926Zn64Y alloy extruded at 250°C and 400°C are studied, in as-extruded and heat treated conditions. The icosahedral phase particles stimulate recrystallization during extrusion, resulting in fine grain size. Tensile and compression tests at room temperature show comparable yield strength, with a yield asymmetry ratio up to 0.98. c-type dislocations are observed in the grains near the submicron size icosahedral phase particles. The source of these dislocations is believed to be dissociation of <c+a> type non-basal dislocations. No dislocation pile-ups on icosahedral phase particles are found. {10 1 2} type twinning occurs in compression.

Jan 1, 2006

By F J. Pearce

The Steel Company of Canada, utilizing the S-L process, has produced partially and highly reduced pellets for use in the blast furnace. Experimental blast furnace tests, using reduced pellet burdens, have been carried out. The changes in production rate, fuel rate and general performance of both the S-L and the blast furnace processes are indicated. Introduction T HE ore burdens for a blast furnace may be improved in two ways: chemically, by concentrating the ore to a high degree of purity; and physically, by agglomerating or closely sizing the ore particles. Today, many b1ast furnaces are charged with closely sized agglomerates, some of which contain upwards of 66 per cent iron. The further improvement of these burdens by chemical concentration may, in many instances, be uneconomic due to the large losses of iron that occur during processing. Assuming that it would be possible to reject all of the gangue minerals, the maximum level of concentration of iron in the hematitic ores would be only about 70 per cent.

Jan 1, 1964

By J. Q. Chen

The elastic-plastic behavior and the fracture mechanisms of two 2198 Al-Cu-Li thin sheets are investigated. The first material (2 mm thick) is in a recrystallized state after cold rolling. The second material (6 mm thick) is hot rolled and has a fibrous grain structure. The two materials are studied in both T351 and T851 conditions. Tensile tests are carried out along different sheet directions using flat and notched specimens. Fracture resistance was characterized using Kahn tear specimens and M(T) panels. Macroscopic fracture surface of smooth tensile specimens depends not only on testing material but also on the loading direction. For Kahn tear specimens, fracture is initiated in a small flat triangle whereas slant fracture is observed during crack propagation. Fracture mechanisms were investigated using scanning electron microscopy (SEM) and X-ray 3D tomography.

Jan 1, 2011

By Erik C. Westman

Knowledge of the orientation and relative magnitude of in-situ stresses at the mine scale is important for safe and efficient production from an underground mine. With this knowledge, stope location and scheduling can be optimized. Passive seismic tomography was used for imaging horizontal stress distribution at the mine scale. Microseismic measurements from the Creighton mine were used as input for the tomography calculations. The double-difference tomography algorithm was used, which provides the most precise results. The results clearly show a low velocity zone in the previously mined areas bounded by two high-velocity lobes located adjacent to the mined openings at locations consistent with those expected due to the horizontal stresses at the mine. The overarching goal of the research is to provide a tool that can augment both numerical modeling results and underground geotechnical measurements to allow the mine operator to produce in the safest and most efficient manner possible.

Jun 1, 2012

By R. Roufail

Mineral exploration is in a race to employ drilling technology that can perform the exploration and drilling investigation in a fast and inexpensive manner. After an extensive study of the available drilling technologies in the market, coiled tubing was chosen as a tool to be employed for mineral exploration due to its flexible mobility and ease of operation with a minimum number of personnel. Since coiled tubing technology is primarily used in the oil and gas industry, it was important to re-design the coiled tube rig to drill hard rocks in a fast and feasible manner. The main requirements were to drill the smallest feasible hole diameter and go as deep in the ground as possible, in the shortest reasonable time. The drilled rock particles, cuttings, are to be collected and analysed at the surface for their metal mineral contents. The process also needs to be repeated multiple times at different locations for mapping, without the need to change the tube on the rig due to failure or potential failure. The focus of the new designed coiled tube, for drilling and mineral exploration, is three fold. First is to increase the rate of penetration in drilling by designing a small high speed turbo motor. Second is to determine the controlling parameters of cuttings transport to effectively lift the cuttings to the surface for analysis and third is to minimize the overall weight of the rig for manoeuvring and prolong the life span of the coiled tube string. In this paper, a small downhole turbo motor, 5cm outer diameter, is designed to achieve a rotation speed of up to 10,000 rpm to fit on a small bit, coiled tube drilling assembly. The motor design utilised multiple finite volume and finite element analysis softwares for fluid flow study and fluid structural interaction analysis. The paper is also introducing the concept of a flow slurry loop that is designed to lift the cutting particles to the surface for mineralisation analysis. The controlling parameters of the cuttings transportation are the particle?s physical properties such as size, density, concentration and shape, as well as the rheological properties of the carrying fluid, drilled hole angle, as well as the fluid flow rate and flow dynamics within the annulus gap between the coiled tube and drilled hole. Such parameters are addressed via experimental work as well as numerical analysis. The paper is also presenting the selection and testing procedure of the material type for the coiled tube string. The tube needs to be light in weight for overall rig weight and its transportability. The tube is also required to drill several dozens of investigation holes before failing due to fatigue. A fatigue bending machine is designed to test the endurance limit of candidate materials for coiled tube strings and a performance index methodology is followed for material selection of the optimum material. The coiled tube rig is designed to be light in weight for transportation and relocation. It is also required to speed the drilling operation with the minimum footprint and reclaim the drilled rock particles for mineral composition analysis at the surface.

Aug 1, 2013

By S. G. Shabestari

In the metal casting industry an improvement of component quality mainly depends on better control over the production parameters. Thus, thermal analysis cooling curve of the alloy is used for process control in aluminum casting industry. Cooling rates of the alloy during solidification process affect microstructure, grain size, eutectic silicon morphology, and dendrite arm spacing (DAS). In this research, effect of cooling rate on the microstructure and solidification parameters of 319 aluminum alloy that is a widely used alloy in automotive industry, has been investigated by means of thermal analysis. Seven different cooling rates have been obtained by using CO2-bonded silica sand molds with two different wall thicknesses, hot-work tool steel molds (H13) with and without coating, thin-wall steel molds with different coatings. In each case, cooling curve and first derivative cooling curve have been plotted by use of very accurate thermal analysis equipment. Effect of different cooling rates on solidification parameters e.g. Nucleation temperature (TN,a), nucleation undercooling (ATN,a), recalescence temperature (TR,a), solidification range (AT,s), and total solidification time (t 0 have been studied in the liquidus region. Microstructural evaluation has been carried out and DAS were measured in all solidification conditions. A numerical equation was proposed to predict cooling rates via measuring DAS in 319 aluminum alloy. Nucleation process and the effect of cooling rate have been interpreted by using thermal analysis cooling curves and microstructural study.

Jan 1, 2004

By A. L. Valdivieso

"The correlation obtained by plotting pH of maximum adsorption of dextrin versus the isoelectric point of involved metal hydroxides can be used to predict the depressing effect of dextrin on flotation in ""pure"" sulfide mineral systems. Sulfides are strongly depressed by dextrin whenever their surfaces are coated by the corresponding metal hydroxide. The efficiency of dextrin as a depressant is affected by the adsorption of the sulfhydryl collector. Hydrolyzable cations modify this relationship in flotation of sulfide ores. This type of deviation of the real-life systems from the predictions based on the behavior of the pure systems shows the possible ways that could be followed to further improve the obtained correlations. Advances in Mineral Processing Science and Technology Proceedings of the 48th Annual Conference of Metallurgists ofCIM Sudbury, Ontario, Canada Edited by"

Jan 1, 2009

By Dale Verran, Jared Orynik, Chad Sorba, David Bronkhorst

Denison Mines Corp. (“Denison”) has a 90% interest in the Wheeler River Uranium Project (“Wheeler River”) located along the eastern edge of the Athabasca Basin in northern Saskatchewan between the Key Lake mill and the McArthur River uranium mine. The project is host to the high-grade Phoenix and Gryphon uranium deposits, discovered by Denison in 2008 and 2014 respectively, which include combined Indicated Mineral Resources of 132.1 million pounds U3O8 (1,809,000 tonnes at an average grade of 3.3% U3O8). The Pre-Feasibility Study (“PFS”), completed in accordance with NI 43-101 in September 2018, is highlighted by the selection of the In-Situ Recovery (“ISR”) mining method for the development of the Phoenix deposit, with an estimated average operating cost of $4.33 (US$3.33) per pound U3O8. Phoenix is the highest-grade undeveloped uranium deposit known globally, including Indicated Mineral Resources of 166,000 tonnes at 19.1% U3O8 for 70.2 million pounds U3O8. The paper aims to provide a summary of Wheeler River and an overview of the proposed development of the Phoenix and Gryphon deposits according to the PFS completed for the Project. Further details regarding the PFS, including additional scientific and technical information are described in greater detail in the NI 43-101 Technical Report titled "Pre-Feasibility Study for the Wheeler River Uranium Project, Saskatchewan, Canada" dated October 30, 2018 with an effective date of September 24, 2018. A copy of this report is available on Denison's website and under its profile on SEDAR at www.sedar.com and on EDGAR at www.sec.gov/edgar.shtml.

Jan 1, 2020

By Thomas G. Madgwick

Introduction Development of oil and gas is still centred in the Province of Alberta, much as it was when C. C. Ross read a paper on this subject three years ago at the Annual General Meeting in Montreal; but so far as gas is concerned, its early production in Saskatchewan seems now assured. The three years that have elapsed since Mr. Ross&apos; paper have witnessed a growth in the world&apos;s production of oil that has created a potential supply out of all proportion to the demand for petroleum products, and one that has resisted the most energetic efforts of the industry entirely to control. The natural result has been very much to retard the active prospecting of new structures in the Prairie Provinces with any immediate view to oil production, although the same factor has not hindered the search for gas to the same extent. One consequence has been to divert the attention of organized oil operators from wildcat drilling to more detailed geological investigation than had hitherto been customary, sometimes accompanied by test drilling with a view to the elucidation of geological structure rather than to the immediate development of production which at the present is not needed. Nevertheless, in spite of the growth of this phase of oil prospecting - which the writer would be the last not to welcome as a very real blessing and of far greater value than indiscriminate wildcat drilling in either the complex structures of the foothills or the simpler but largely concealed formations of the plains- it is most satisfactory to have to record that in these three years the growth of production both of naphtha and the heavier crude-oil has kept pace with the by no means inconsiderable growth in the production and utilization of natural gas.

Jan 1, 1929

By Richard Dawson

Presentation Outline? Northeast BC Coal Fields Overview and History ?New mines and projects in development ?Design Issues for steeply dipping footwall slopes ?Design issues for angle-of-repose waste rock dumps

May 1, 2006

The dynamic breakage process of rocks by the impact of a hydraulic hammer is more complex than one normally assumes. It is even more difficult when one has to conduct the breakage under water. In such cases one does not know exactly what the surface topography and composition are at the bottom of the sea or river and, hence, it is more difficult to select the best position of the hammer before starting the hammering. Typically, an industrial hammer has a diameter of about 250 mm, a length of about 1.25 to 1.75 m and a mass of several tons. The hammer frequency can be up to 50 impacts per minute. The general principles of rock hammering can be easily summarized, but this knowledge is not sufficient to adapt adequately the method for less common rock conditions (e.g. less brittle rock, presence of vertical and subvertical fractures, etc.). That is the reason why we initiated a research project, whereby a scale model has been developed to conduct experiments in the laboratory and whereby discrete element simulations are being conducted. Both aim at a better understanding of the basic mechanisms of rock hammering. The scaled experimental model allows varying the impact energy and the static weight independently. Within the experiment, the hammer is in contact with the rock specimen under a certain confining pressure and with a certain contact pressure due to the static weight. A weight falls on the hammer, creating the dynamic action or impact; the height over which the weight falls can be varied. The penetration is recorded after each impact. After a certain penetration the test is stopped and the internal crack patterns are described. Some simulations have been conducted, allowing the modeling of individual fracture initiation and growth during the penetration of the hammer by either a constant displacement rate (using the UDEC-code) or by introducing the dynamic process (using the PFC-code). Some of the observed features in the laboratory experiments can be visualized in the simulations. However, further research is needed to allow the simulations being an adequate tool to well understand the dynamic process in laboratory experiments, as well as the in-situ behavior.

Aug 1, 2013