Search Documents

By Stephen C. Tadolini

"The use of a torque wrench to establish the amount of actual load developed on an expansion anchor bofting system dates back to work completed in the early 1950s. The advent of ultrasonic measurement systems and hydraulic torque wrenches has made it possible for the U.S. Bureau of Mines to perform torque-tension measurements in the laboratory and the field much more accurately. The results indicate that the amount of initial boft preload may be overestimated by amounts in excess of 45% of the expected load using torque wrenches. This inaccuracy is primarily due to the friction that occurs between the bearing plate and the head of the boft. These parameters become extremely important when the support system is being used to prevent joint members from slipping relative to each other or when the boft acts as a heavy spring to clamp two or more sections together. Methods to overcome the frictional losses are presented in conjunction with a laboratory method to determine the actual torque-tension ratios for expansion anchor and combination bolting systems.IntroductionMechanically anchored roof bolts have been widely used in the mining industry since their introduction in 1947. Estimates made in 1989 indicate that out of 85 million fixtures, approximately 49 million bolting fixtures still use applied tension to complete the reinforcement necessary to maintain stable openings. Nearly 85 million bolts are used yearly. The most widely used bolt is the resin-anchored headed rebar, followed by standard mechanical roof bolts, specialty bolts (mechanically anchored, resin enhanced fixtures) , and combination bolts . Po st-tensioned resin rebars, combination systems, and friction stabilizers make up the remaining 10% of the units used (Fig. I).For mechanical, combination, and tension rebar bolts, the bolt tension is the primary means of reinforcing the roof, but in many cases, because of poor installation procedures, the bolts are ineffective. Mine operators recognize the importance of proper installation procedures. Long-term bolt tension measurements are required in the Code of Federal Regulations (CFR)In each bolting cycle, the actual torque or tension of the first tensioned bolt installed with each drill head shall be measured immediately after it is installed. Thereafter, for each drill head used, at least one roof bolt out of every four installed shall be measured for actual torque or tension. If the actual torque or tension of any roof bolts measured is not within the range specified in the roof control plan, corrective action shall be taken."

Jan 1, 1991

By S. J. Laskowski

In potash ore flotation, carried out in NaCI-KCI saturated brine (about 6-7 molar KC1 and NaCI solution), long-chain primary amines are used as flotation collectors. Long-chain primary amines are poorly soluble in water and their solubility further decreases at high electrolyte concentration. For ionic surfactants there is a characteristic temperature (Krafft Point, KP) below which their solubility is too low for micellization. In a previous study, the effect of pH on the KP of dodecylammonium chloride in water was determined [Q. Dai and J.S. Laskowski, Langmuir, 7, 1361-1365 (1991)]. This paper deals with the effect of electrolyte concentration on the KP of dodecylammonium chloride. The derived theoretical relationship between the KP and the critical micelle concentration (CMC) for dodecylamine can be used to calculate the KP for electrolyte concentrations of up to 0.5 mol/L (about 8% NaCI-KCI brine). A simple experimental procedure for the determination of the KP for higher electrolyte concentrations is also described. The results show that the Krafft point of dodecylamine increases from about 17-18°C (in distilled water) to about 80°C at 16% brine saturation.

Jan 1, 2006

By M. Sommerfeld, U. Schwarz-Schampera, B. Friedrich, D. Friedmann

The steadily growing demand for metals and their price increase at metal exchanges make the mining and utilization of marine mineral resources like polymetallic nodules, manganese crusts or sulfide deposits in the near future a viable option to potentially increase the supply of base and precious metals. For a country with low potential to mine land-based resources like Germany, the industrial recovery of metals from marine mineral resources could lead to a decreased dependency on imports. In this study, seafloor massive sulfides from the German license area in the Indian Ocean (Kairei field, Southern Central Indian Ridge) are treated to recover copper and precious metals. The aim of the project is to demonstrate the transferability of existing metallurgical techniques to the raw material of deep-sea massive sulfides. As a starting point to process this unconventional resource, samples from the Indian Ocean are chemically analyzed and mineralogical characterized. A comparison is carried out between the samples and land-based copper resources, to highlight the potential which lies in mining the deep-sea floor. This paper will show the general possibility of applying a two-stage pyrometallurgical process, based on a concentrate smelting operation, followed by a converting operation in lab-scale to the provided samples of massive sulfides. Generated slag from the concentrate smelting and the converting operation are investigated by X-ray diffraction to determine the mineralogical composition. The two-stage pyrometallurgical process is investigated by the thermochemical modelling tool FactSageTM 7.2 to evaluate the phase distribution of relevant elements between the metal, matte, slag and gas phase. The thermochemical boundaries of the pyrometallurgical process are therefore set and the results of the thermochemical study can be used as an indicator for the efficiency of an up-scaled process and the generated amount of side-streams, which need to be further treated or circulated back into the process. INTRODUCTION Seafloor massive sulfides (SMS) are the third kind of discovered deep-sea minerals besides ferromanganese nodules and cobalt-rich ferromanganese crusts (Sharma, 2017). They occur in water depths around 250–4,000 m (Koschinsky et al., 2018). SMS are characterized by a high base metal and sulfide content. They were created by fluid circulation and hydrothermal convection over time (Han et al., 2018). Commonly, areas rich in SMS are associated with hydrothermal vent fields on the seafloor (Keith et al., 2018).

Jan 1, 2019

By Michel Ruel

Most plants do not track how their systems perform. Optimization is the easiest way to benefit from your control systems. We suggest an approach in four phases. The first phase is to assess all equipment to determine the performances for instruments, valves, variable speed drives, and other equipment. The second phase is to remediate instrumentation problems, including the ones pertaining to valves, variable speed drives, analyzers, transmitters. When equipment is in order, loops are put back in automatic mode. If a loop oscillates, use standard default values for this type of loop. The third phase consists in validating the control strategies, properly configuring the systems (control system, programs and parameters, HMI, alarms), and then tuning the loops and control strategies. The fourth phase consists in analyzing the process and expected performances in order to optimize the control loops and control strategies. If performance is not sufficient, a decision tree will be presented to determine the right approach: advanced regulatory control, model predictive control, or fuzzy logic control. Once all steps have been completed, control performance monitoring software is used to sustain the results and pinpoint equipment or loops not performing as stated. Alarm management and rationalization could also be performed after auditing the alarm system, if needed. Examples from plants will be used to demonstrate how this step-by-step method is applied and produces results. INTRODUCTION Maximizing what you already have is the best investment to remain competitive. This article aims to show the benefits of a systematic approach using modern tools to improve plant performance. We at BBA suggest dividing the work in four phases, and a subsequent phase can begin when the previous one has progressed: Assess, Remediate, Stabilize, Optimize, or add advanced control. This approach has been successfully applied to several sites. Examples and illustrations from these plants demonstrate how this step-by-step method is applied and produces results. Under the BBA method, there are four questions to answer before proceeding to the next step. For each control strategy, you should ask the following questions: Assessment: Does it work? Remediation: Do you use it? Stabilization: Is it stable? Optimization: Does it perform? Do you need advanced control?

Jan 1, 2019

By T. Güyagüler, U. Y. Önder

"This study investigated the psychrometric properties of ventilating air in GAL coal mines. Related measurements were done in underground openings and have been arranged as input data for computer programs prepared for ventilation network and psychrometric analysis.Results obtained from network analysis have been used for psychrometric analysis of ventilating air. Changes in heat and moisture content of air in two major path s between entry and discharge of ventilating air have been investigated. Psychrometric processes occurring in the mine were determined and are shown graphically in Figures 1 and 2. Special attention has been given to determine the changes in psychrometric properties and processes involved in the faces. Results are outlined in this paper.IntroductionThe psychrometric properties of mine air are important factors to mine productivity and efficiency. Therefore, psychrometric analysis should be made for all underground mines; any undesired situation observe d could be corrected by taking the necessary precautions.The analyses were done as a case study for GAL mines, the only mechanized lignite coal mine in Turkey. In this mine, workable reserve is about 300 million tons of coal and yearly planned production is 2.2 million tons. Production is continuing from a coal measure-bed having two coal seams with average thicknesses of 1.52 m and 1.72 m respectively. A 0.85 m shale band exists between these two seams.Two full y-mechanized faces, approximately 220 m long, usually work simultaneously. All measurements, including mine gases and air velocity, are done by sensors connected to a control room by a monitoring system.In the analysis, a line diagram is utilized to described the mine on which every junction and branch is numbered."

Jan 1, 1992

By J. Baz-Dresch

"The most cost-effective method of placement of the high strength fill used in the Cannon Mine' s overhand cut-and-f ill bench stopes was determined to be truck haulage. Constraint s imposed by the mine layout dictated the use of a truck which could dump its load in a fifteen-foot high drift. The Dux Teledumper truck was selected as the most suitable unit for this application based upon operational and maintenance parameters which included a telescoping, tilting dump box; large load capacity; and robust construction. Development of the truck continues through the cooperation between the manufacturer and user. INTRODUCTIONThe Cannon Mine is situated in the centre of Washington state, approximately midway between the cities of Spokane on the east and Seattle on the west. The mine complex is located three block s south of the Wenatchee city limits at the eastern base of the Cascade Mountain range.Asam era Minerals (U.S.) Inc., with 5I% ownership, operates the Cannon Mine. Breakwater Resources, Ltd. holds the remaining 49%.Annual paroduction is 520 000 tons per year, presently on a 21-shift per week operating schedule for both the mine and the mill.All production is presently won by overhand bench stoping with backfill. Stoping starts with 15-ft high by 24- or 30-ft wide sill cuts driven above and below a stope block . A drop rai se and slot are used to open a bench which is then slabbed toward the open slot. Truck-placed backfill is dumped into the mined - out stope from the upper sill cut. This stoping sequence is repeated until the top of the ore block is reached . The top sill cut is then tightly filled with backfill to minimize subsidence and to provide adequate roof support during extraction of the pillars.Mining equipment consists of hydraulic drills and rubber-tired, diesel scoops and trucks."

Jan 1, 1989

By Larry G. Twidwell, Corby G. Anderson, Camille M. Fleuriault

"The selective precipitation of iron as ammonium jarosite is a well-established industrial technology in base metals hydrometallurgy. It is a key technology in minimizing iron tenors which would be disruptive to downstream processing. It also provides a more readily filterable iron solid to better facilitate materials handling. This paper elucidates the fundamentals behind industrial iron precipitation. Then, the details of the successful optimization of an industrial ammonium jarosite circuit are presented.HYDROMETALLURGICAL IRON REMOVAL FUNDAMENTALS Iron is the fourth most abundant element in the Earth’s crust (5% by weight) and is often found in complex ores such as sulphide-bearing formations. Iron represents an issue though during leaching, a technology which is widely used for the treatment of this type of ore: •,Iron has the particularity of forming hydroxides when leached under certain conditions. Iron hydroxides form a viscous gel, which is difficult to filter and traps valuable elements such as silver. •,Iron is solubilized along with other metals and interferes with the subsequent extraction steps. As a result, purification of the pregnant leach solutions is required to achieve economical extraction of base metals. In the 1960s, metallurgists developed iron precipitation processes for solution purification (Habashi, 1999). Nowadays, precipitation of iron bearing species, such as goethite, hematite or jarosite, has become one of the most common methods used in the industry to purify leach liquors. To be suitable, the precipitate has to be readily filterable and thus must not be too fine of particle size. Precipitation can take place in autoclaves at medium to high temperatures, under an oxygen or air overpressure (Tourre, 1984, Fleuriault 2016, Fleuriault Anderson Shuey, 2016))."

Jan 1, 2016

By T. Gerritsen, R. MacRosty, R. Pula

For several years Hatch has been installing fibre optic temperature sensors on the copper cooling elements of smelting furnaces to improve monitoring capabilities in critical locations. The metal/matte tapblock is a key area to monitor in the furnace as it undergoes severe wear from the molten material repeatedly drained through it. The high wear rate around the tapblock means downtime is necessary to perform refractory repairs. A good understanding of the tapblock condition allows the operation to maximize safety and production; consequently the metal/matte tapblocks have been the focus of this study. Fibre optic technology allows the installation of numerous sensors in locations that are very sensitive to refractory thickness, thereby providing information previously unavailable with traditional measurements. The transient nature of the thermal response to tapping and the three-dimensional geometry of the tapblock confound the interpretation of refractory thickness from temperature measurements. This paper focuses on the analysis of both plant data and thermal modelling simulations and details the progress made in relating the temperature measurements to the refractory thickness in front of the copper tapblock.

Jan 1, 2014

By M. W. Wadsley

"Physical and chemical property models are widely used in process engineering. There exist, in the published literature, completely empirical models of ''thermodynamic properties"", that is, property models that are not consistent with the laws of thermodynamics. There also exist property models that purport to be thermodynamically consistent but are flawed in their implementation. There are also published property models that are consistent with the laws of thermodynamics but that do not reproduce property values with an acceptable accuracy. A practicing engineer might be asked to assess very different property models for which there are a variety of claims. This paper discusses features of thermodynamic and empirical property models that may assist in their practical evaluation and implementation."

Jan 1, 2005

By N. Musee, N. Kornelius

This study presents a neural network approach to modelling the liberation of gold bearing ores. A complete mineralogical analysis of unmilled and milled ores, including gold deportment and gangue content are used as inputs to a self-organising neural net which generates order preserving topological maps. The arrangement and shapes of these clusters are coupled to unmilled free gold data to predict gold liberation in milled ores (absolute error: 4.2%). Moreover, the self-organising maps were diagnostic of the quality of data used, indicating that the relationship between particle size and gangue material content requires further investigation.

Jan 1, 2005

By Gary S. Anderson

Rajant Corporation is the global leader in mining communications systems implemented a vision to develop a wireless network that is rapidly deployed, self-powered and managed, for portable or fixed configurations ? Mobile, Portable, Self-Powered, Secure and High Bandwidth. The network configures itself allowing for very rapid deployment without the time delay and personnel typically required for set-up and configuration. Rajant?s proprietary technology ?InstaMesh®? is incorporated in a device called a BreadCrumb®. Rajant has filed several patent applications on its proprietary technology and has received trademark protection on its brand names. The BreadCrumb® uses technology which allows mining, military and first responders to easily establish internet connections at remote sites or situations where existing internet communications has been disrupted. The BreadCrumb® products are standards-based Wi-Fi 802.11 a/b/g compliant, ruggedized, lightweight, portable; self-meshing and the system can be established by just turning on several of the BreadCrumb® units. The Rajant Network has evolved in the ?One Network? philosophy and has been deployed by both the military and homeland defense organizations. With multiple radios, transmitting on multiple frequencies as the same time, bandwidth is doubled, the speed of the network is enhanced, management is simplified, and manageability is made easier. Rajant has partnered with world class integrators and partners, including ten CAT dealers, a world-wide mining technology company, a mining and construction software company and leading technology innovators in mining automation and operations. Recently, Rajant provided a significant network to Rio Tinto?s Iron Ore of Canada Mine in Labrador City, Newfoundland, Canada, Kennecott Utah Copper Mine, and is currently the wireless standard at Peabody Energy and several mines in Australia. These networks range from 20-250 BreadCrumbs®. The result is a meshed mobile broadband network capable of operating in a vast open pit active mining space. Simultaneous applications currently running on these BreadCrumb® networks in the mining sector consist of Caterpillar?s VIMS?s, CAESultra grade control and Aquila Drill Management Systems, Carlson Grade Control systems, Jigsaw Technologies and Modular Mining fleet management system, Ground Probe Radar, an Automatic Train Operation and various video and VoIP applications. All vendor applications have been turned off and all applications are running on Rajant?s ?One Network?.

May 1, 2010

By A. E. Boudreau

It has long been recognized that platinum-group-element (PGE) deposits in layered intrusions preferentially occur in intrusions that crystallized from high-Mg parent magmas. Recent studies suggest that evaluation of any given intrusion for economic PGE potential should also include assessment of the PGE, sulfur and chlorine concentrations in the cumulates and potential parent liquids. PGE: Magmas that contain relatively abundant Pt and Pd are the best candidates for forming economic deposits. Although analyses of coeval sills and dikes are the best indicators of primary magmatic PGE concentrations, analysis of the cumulates themselves is also valuable. For example, within the Stillwater complex, background PGE values in cumulates from the ultramafic sections of the complex contain, on average, several 10s of ppb Pt and Pd. Background concentrations of this order are suggestive that the magma was not depleted in the PGE. Sulfur: Conventional petrogenetic models for the formation of PGE deposits in layered intrusions require the PGE to have been concentrated during a magmatic sulfide-saturation event. In contrast, some hydro thermal models suggest that sulfur and the PGE were mobilized from footwall cumulates by upward-migrating, high-temperature hydrothermal fluids. Both models suggest that significant PGE deposits are likely to occur at and below the level where stratigraphic increases in whole rock sulfur concentrations occur. Chlorine: In both the Stillwater and Bushveld complexes the cumulate sequences below the major PGE-bearing zones contain anomalous Cl-rich apatite. The chlorapatite component of apatite in these rocks may exceed 40% and, in the Stillwater complex, typically exceeds 90%. It is stressed that pristine igneous mineral analysis and not whole rock data be used, as whole rock Cl concentrations may be affected by very localized (grain boundary), low-temperature alteration. Intrusions that crystallized from high-Mg, high-Cl magmas appear to have the best potential to host significant PGE deposits.

Jan 1, 1995

By Dani J. Alldrick, Alastair J. Sinclair, Colin I. Godwin

"Abstract - The Stewart mining camp has a long history of precious and base metal mining. The camp is abundantly mineralized, with more than 200 widespread, varied, vein prospects, deposits and orebodies. These show wide variations in the mineralogy of ore, gangue and alteration assemblages, and wide variations in textures and structural settings. This report establishes the timing of the different metallogenic epochs and suggests a specific exploration application for systematic lead isotope analyses.Galena lead isotope ratios from a range of mineral occurrences indicate that all these varieddeposits formed during two main mineralizing events. Lead isotope data from the Stewart mining camp do not provide absolute ages for the formation of mineral deposits, but the relative distributions of data are consistent with dates determined in other studies. One ore-forming episode occurred in the Barly Jurassic and the other in the Middle Eocene. Both metallogenic epochs were brief, regional-scale phenomena. Sorne deposits from the younger mineralizing episode were em­ placed adjacent to or superimposed on the older deposits.Field and laboratory studies show that the two metallogenic epochs are characterized by different base and precious metal suites: Barly Jurassic gold-silver-zinc-lead-copper; and Middle Eocene silver-lead-zinc. Therefore, showings of different ages have different base and precious metal potentials and deserve different exploration emphasis. Lead isotope studies provide a reliable, cost-effective method for evaluating the age and commodity potential of small or recently discovered mineral showings and for setting exploration priorities on properties with several varied mineral occurrences . The determination of the age and metal potential of a prospect at an early stage of exploration may govern the urgency, intensity or even the necessity for further exploration work."

Jan 1, 1993

By D. B. Hyma

"The Raglan Ni/Cu property is located on the Ungava Peninsula in Northern Quebec, Canada, at a latitude of61°42' and a longitude of73°40', approximately 40 km southwest of Douglas Harbor. Geological reserves are estimated at 18 million tonnes, grading 3. 1 % nickel, 0.9% copper and smaller amounts of cobalt and platinum group metals.Extensive project development has defined the concentration process, concentrator sizing, tailings and environmental management required for this project.The grinding circuit selected is a fully autogenous primary grind, with pebble crushing and a pebble mill for secondary grinding to produce a product of 80% -70 microns for flotation.The flotation circuit is a simple circuit utilizing roughing, a regrind of rougher concentrate to 80% -20 microns, two stages of column cleaning with a cleaner scavenger bank on the column tails.Concentrate handling options were thoroughly reviewed because of the pyrophoric nature of the concentrate, remote site location and long distance to downstream processing. The preferred option, currently.is to dry the concentrate at Raglan to less than l % moisture and then pneumatically handle the powder.A detailed analysis of tailings placement options, suggests filtered tailings placement to be the preferable route for the Raglan site.INTRODUCTIONThe Raglan Project, as proposed by Falconbridge Limited, will develop extensive nickel-copper deposits in the Ungava Peninsula, Quebec, Canada. The project schedule and construction conditions in the project area are demanding. The Raglan mineral deposits have been the subject of numerous studies and evaluations over the last thirty years and the Phase I 1991 pre-feasibility document includes exploration information obtained in the 1989 and 1990 drilling seasons. This review concluded that an 800,000 tonnes of ore per year mining and concentrating complex located at Katinniq could produce 20,000 tonnes per year of nickel at competitive costs."

Jan 1, 1993

By Fridrik J. Kristjansson, Stephen R. Hicock

"Three varieties of till are recognized in the Beardmore-Geraldton area: local lodgement till, nonlocal carbonate till, and local supraglacial till. The local lodgement till unit is examined in detail for the first time in this paper. It is the best potential overburden exploration medium for gold and other metals because its particles were locally-derived and deposited subglacially, probably within a few kilometres downglacier (southwestward) from their sources, and have not been diluted by distantly-derived glacialdebris. Both local tills are richer in gold and other metals, relative to nonlocal carbonate till. Local lodgement till rests on bedrock and was encountered frequently at or near the surface in thin drift/bedrock terrain (a widespread terrain type within the west half of the study area), and commonly at the base of boreholes in thick till terrain.INTRODUCTIONDrift prospecting in areas of glaciated terrain has been well documented (in a variety of journal publications and symposium volumes; e.g . Strobel and Faure 1987; MacDonald and Mills 1988) and has proven valuable especially where overburden thicknesses hinder traditional exploration techniques. Drift prospecting techniques may well prove valuable in the Beardmore Geraldton area. This applies especially to the Wildgoose Lake Turkey Lake area where a thick and laterally extensive sheet of nonlocal carbonate till has impeded conventional mineral exploration programs (Fig. I; note the lack of gold occurrences around Wildgoose Lake).Till in .particular has been cited as the best prospecting medium among the various types of glacial sediment (e.g. Shilts 1984). Three end member till varieties are recognized in the study area: (I) local lodgement till which rests directly on bedrock; (2) non local carbonate till; and (3) local supraglacial till which occurs predominatly within, or just downglacier of, upland areas where it commonly mantles the other till varieties. Previous authors have documented how the non local carbonate till hinders gold exploration (Geddes and Kristjansson 1986; Karrow and Geddes 1987; Kristjansson 1986; Hicock 1986, 1987a, b, 1988; Kristjansson and Thorieifson 1987; Thorleifson and Kristjansson 1987, 1988a, b) and why the local supraglacial till may be a good unit for prospecting (Hicock 1986). One detailed surficial geology map sheet of the area has been published (Kristjansson et al., 1988) and others are in preparation. Closs and Sado (1981) reported on the geochemistry of soils and glacial sediments in the west half of the study area. This paper documents the local lodgement till unit and demonstrates why it is the best overburden unit to use for drift prospecting."

Jan 1, 1989

By M. R. Khalesi, S. Bellec, C. Bazin, D. Hodouin

Batch grinding tests conducted on a gold ore indicated that gold is not randomly distributed within the size fractions of the ground ore. Since gold leaching performances were found to be dependent of the size of the gold carrying particles an integrated gold ore grinding-leaching simulator should incorporate a method to predict the gold size distribution of a ground ore. The paper describes the results obtained from batch grinding tests showing the non random distribution of gold within the size intervals of a ground ore and the initial developments of a grinding model to predict the gold size distribution in a batch grinding product.

Jan 1, 2011

By J. Bednar, R. R. Rogers, W. Dingley

"Zinc is by far the most important metal used for protecting steel from the ravages of corrosion, and cadmium is also used extensively for this purpose. These metals are applied by electrodeposition in cyanide baths when a particularly good appearance and high throwing power are required. One great disadvantage in using these baths has been the decrease in cyanide concentration and the increase in carbonate concentration that takes place during the plating. Another disadvantage has been the development of serious embrittlement in high-strength steels. The present authors have developed new cyanide baths for electroplating both zinc and cadmium on steel. These baths are stable in composition during plating, they have not produced appreciable embrittlement in the high-strength steels that have been investigated up to the present time, and they permit the use of considerably higher plating current densities. In addition, they produce extremely fine grained coatings that are attractive and have excellent adherence and covering properties. Brighteners can be used in the plating baths if bright finishes are required."

Jan 1, 1967

By G. M. Ritcey, B. H. Lucas

In the conventional alkaline leaching of concentrate containing nickel, copper and cobalt, copper is usually removed from the system, prior to nickel reduction, by sulphide precipitation. A new process is described for the selective extraction of copper and separation from cobalt and nickel, using liquid-liquid extraction. General Mills LIX-63 dissolved in a kerosene diluent is the extractant. Trace amounts of co-extracted cobalt and nickel are easily removed by a scrub treatment, and copper is recovered from the extract by sulphuric acid stripping, thus providing a solution amenable to the oroduction of electrolytic copper. Estimated processing costs are included together with a proposed flowsheet.

Jan 1, 1972

An Attractive Investment ?Near term low cost and secure PGM producer ?restricted supply legislated demand ?strong pipeline of resource development ?Building Canada?s largest undeveloped PGM-Cu resource ?All work (resource, reserves, DFS, EA) is NI43-101 compliant ?Strong balance sheet: over $8 m in cash with no debt

May 1, 2010

By W. S. Hargratt

THE present era of exploitation of the Little Long Lac and Sturgeon River areas commenced in 1925, when Beardmore Gold Mines started development of what is now the property of Northern Empire Mines. A shaft was sunk in 1927-28 and a very limited amount of underground work was carried out, following which the property was shut down. It remained idle until 1932, when Empire Star Mines, a Delaware Company, optioned the property. This Company formed the Northern Empire Mines Company, Limited, to operate the mine, and immediately instigated an aggressive programme of surface and underground development. By the summer of 1933, sufficient ore was indicated to justify the installation of a small mill. The decision was also reached to bring in electric power. A power-line was built from Hydro, the Ontario Power Commission's development on the Nipigon river, to the mine, a distance of approximately 50 miles. This work was entirely financed by Northern Empire Mines. Mill construction was commenced in October, 1933, and completed by March, 1934, thus making this mine the first producer in this district.

Jan 1, 1940