Search Documents

By D. M. Muir

Many plants produce iron(II)/(III) waste liquors which must be treated by neutralisation and precipitation to remove the iron. Iron can be precipitated as crystalline goethite or jarosite by controlled oxidation at low pH and as magnetite by controlled oxidation at high pH, but only at elevated temperatures (>70°C). This study focuses on the characterisation and settling properties of the iron oxides produced at ambient temperatures using various neutralising agents in order to improve the performance of thickeners. It was found that two-stage addition of caustic to FeC12 solutions produced a fast settling material characterised by Mossbauer spectroscopy and XRD as maghemite and magnetite. However, lime and magnesia additions resulted in more ferrihydrite formation and much lower settling rates because of the enhanced oxidation of Fe(II) by air. Settling rates decreased significantly as the proportion of Fe(III) to Fe(II) in the liquor increased. The mechanism of iron oxide precipitation is discussed together with some reasons for the different behaviour of the neutralising agents.

Jan 1, 2006

By G. Rong, W. Du

Stability of some potential unstable blocks in the left bank slope of Baihetan hydropower station is evaluated in this paper using the three-dimensional (3D) limit equilibrium method. The Baihetan hydropower station is in the downstream of Jinshajiang River, China. The geological condition in the river valley is complex, and many large discontinuities are detected in the slope of the two banks. As a result, much attention should be paid to the stability of the slope in the feasibility study stage. Because the left bank slope is an oblique consequent one, we mainly focus on the slope stability analysis in the left bank. Comprehensive geological exploration is conducted in the studied area and the detected discontinuities are well researched. By building a 3D geological model of the left bank slope, three potential unstable blocks which are close to the dam site are detected. An irregular wedge analysis method is then used to calculate safety factors of the three blocks under three conditions, which are natural condition, rainfall condition, and seismic condition, respectively. It is found that the safety factors of the block 1# and the block 2# are quite low when compared to the suggested values. Extra care must be exercised when excavating the slope near the block 1# and the block 2#. A preliminary reinforcement is also suggested.

Jan 1, 2015

By M. Nejati, A. Paluszny, R. W. Zimmerman

A numerical method is proposed to propagate multiple discrete fractures leading to primary fragmentation in a mine that is being worked using block caving. Deformation is computed using the finite element method, fractures are represented explicitly, and the mine domain is discretized by an unstructured mesh. Bedding planes are represented by systematically varying the elastic modulus of the rock and by defining horizontal weakness planes. Fractures and matrix are represented using parametric surfaces, and tips are defined by their boundary curves. Tip advance is controlled by a failure criterion, and a criterion for propagation direction and magnitude, based on the evaluation of the modal stress intensity factors. A novel domain integral approach is applied to accurately compute stress intensity factors (K) ahead of fracture tips in three dimensions. The method does not require a structured volumetric mesh structure around the crack tip, as integration is performed over a series of virtual surface domains along the crack front. The method is efficient, as it makes direct use of automatically generated, arbitrary tetrahedral meshes, and approximates stress intensity factors (KI, KII, KIII) along each crack front using Interaction-integrals. As opposed to the JIntegral, the method does not decompose K a-posteriori, but instead uses an auxiliary field to directly compute modal K. When using this method, numerical approximations of K do not exhibit dependence on the mesh layout, and require meshes that can generally be ten times coarser than are required by displacement- and stress-based methods. Volumetric meshing requires only, on average, 17% of each computation step. Thus, cracks do not follow any pre-existing mesh structure, and the method is well suited for high-density fracture datasets. The method is demonstrated for primary fragmentation of a mine area covering 110 initial draw points, immediately beneath a 2m high undercut. Displacement is constrained at all boundaries except the surface of the undercut. The growth of the fractures is investigated at the onset of the undercut. Ninety initial disc-shaped fractures are taken into account, each having an initial radius of 10 m. Fractures grow around the undercut, intersect the bedding plane boundaries, and the domain is fragmented as a result.

Jan 1, 2015

By C. H. Wright

Introduction The rapidly expanding and increasingly complex Canadian industrial structure, with the mining, metallurgical, and chemical industries as a large integral part, has, in recent years, brought greatly increased importance and value to our industrial minerals. In the modern economy of our mineral industry the importance which is due the non-metallics has been somewhat overshadowed by the great value of our large metal production and, in addition, by the glamour and fascination usually associated with the mining and treatment of gold ores. The term 'Industrial Mineral' is used in this paper in its usual sense and refers to non-metallics other than fuels. Coal and petroleum products, including natural gas, are considered as industrial minerals in those applications in which they are used for strictly chemical process purposes. Certain reduction metallurgical industries are so closely allied to chemical industries that for purposes been of this discussion no attempt has made to differentiate between them. Chemical industry in Canada today is a fairly large factor in our national economy, whereas in 1898, when the Canadian Mining Institute was born, it was very small indeed. Chemical concerns are largely dependent on industrial minerals for raw materials and process supplies and, as the country has developed industrially, so have the demands for non-metallics increased, not only by chemical industry but also by other large consumers, such as the construction and metallurgical industries. At the present time there is a greater than normal incentive prevailing for new discoveries, due to the serious lack of balance that exists in our import and export trade. This fact has resulted in intensive efforts to rectify the situation by locating new deposits and re-assessing those already known in an effort to enlarge and improve our home production of raw materials and also to extend their processing in Canada for our own needs and for export. The rapid advances in science and technology that have taken place since 1900 have also resulted in many cases of beneficiation and utilization of otherwise too low grade materials in order to satisfy current demands. The purpose of this paper is to indicate the history and the trends of the utilization of industrial minerals in established industry and to indicate the important part played by non-metallics in connection with the opening up of new industries. Some consideration has been given to the continual competition between natural and 'synthetic products and to the general tendency towards more rigid specifications.

Jan 1, 1948

By A. G. Matyas

Process improvements which have reduced the lead content of slag from the Brunswick lead blast furnace are described. Microscope examination and electron microprobe analyses, supported by the results of slag settling and viscosity tests, showed that typically about 70% of the lead in the lead blast-furnace slag was present in the form of entrained prills of metallic lead. The total lead content was found to increase with the magnetic susceptibility of the slag. Measurements in the furnace settler indicated the presence of a magnetite-rich layer between bullion and slag, arising from high magnetite levels in the slag. This layer was believed to inhibit the settling of entrained lead from the slag. Tracer tests showed that the average slag residence time in the settler was less than 2 minutes. Improvements in coke quality and sizing, which led to a reduction in the slag magnetite content, and the installation of a larger settler and a continuous Roy tapper, have all contributed to a significant decrease in the slag lead content.

Jan 1, 1977

By P. Nelson

Extending the campaign life of the Mitsubishi furnaces at Xstrata Copper's Kidd Metallurgical Division Copper Smelter has been a major focus of attention for many years. One aspect of this effort is real time monitoring to detect abnormal conditions and safely shut the furnaces down before significant damage occurs. Traditional real time methods of monitoring the integrity of refractory furnaces containing molten metal include alarms on individual temperatures of the refractory or cooling water. The need to set alarm limits which are not exceeded across the range of normal operating conditions leads to a system that only provides a limited warning, if any, before a failure occurs. Integrity monitoring systems that look at many different signals and alarm only changes in the relationships between the signals have been implemented on the smelting and converting furnaces. The systems are based on principle components analysis (PCA) models and implemented with the monitorMV software package. These provide much more sensitive and selective alarms so that changes in integrity are alarmed well in advance of any event. At a critical alarm level, the converting furnace is set to automatically shut down so that operating and technical personnel can review the situation. The configuration of the systems and operating experience with them will be discussed.

Jan 1, 2007

By T. Bhambhani, Mukund Vasudevan, Partha Patra, D. R. Nagaraj, P. Somasundaram

Selective Ni separation from ultramafic ores rich in serpentines has been a huge challenge in the mineral processing industry, and therefore highly inefficient. Analysis of the root causes of the challenges and consequent development of robust processing solutions were the main goals of the Cytec-Columbia. University-Vale Joint Development Program. In this context, the subject of this paper is limited to one of the key findings of this research program which is the influence of fibrous serpentines on grade-recovery characteristics. Specifically, the poor flotation behavior is characterized by an atypical reverse C-shaped grade-recovery curve.

Jan 1, 2011

By John Vergunst

"This paper traces the development of Ontario 's cap lamp standard. Over the years, numerous Coroner's Juries investigating fatal mine accidents have made recommendations with respect to underground lighting. As well, recommendations to improve mine lighting have been made by two Commissions, investigating mine safety in Ontario.During the past few years, the performance of any cap lamp worn by miners involved in serious accidents, have been measured by the Mining Heal/h and Safety Branch. Large variations in light output were found between and among cap lamp types. These variations have been attributed to the lack of quality control on the bulbs, design of the cap lamp head piece and in some cases, poor maintenance.In 1986, a series of underground tests were conducted to establish the minimum light output from cap lamps required to visually identify loose ground. The results of these tests indicated that a cap lamp should produce a minimum peak illuminance of 1500 lux measured at 1.2 metres from the light source. On May 30, 1987, Ontario became the first province in Canada to legislate the minimum amount of light required to visually assess ground conditions. INTRODUCTIONPoor lighting has been identified as a factor which can contribute to mining accidents. Over the past decade, several Coroner's Juries as a result of inquests into mining fatalities, have recommended improved lighting in mines.The Joint Federal-Provincial Inquiry Commission into Safety of Mines and Mining Plants in Ontario, was appointed to report upon the adequacy of existing arrangements and practice s that may affect safety. This Commission completed their report in April 1981, and recommended that inadequate lighting be investigated as a possible cause of all reportable underground accidents, and that a comprehensive research programinto mine lighting be undertaken.In response to the first recommendation, the Mining Health and Safety Branch of the Ministry of Labour, hereafter referred to as the Branch, initiated a program to measure lighting levels in all fatal accident investigations where inadequate lighting was a possible factor."

Jan 1, 1989

By A. G. Roach

HISTORY AND LOCATION SEAL HARBOR GOLD MINES, LIMITED, was incorporated in January, 1934, to take over 116 acres of mining lands in the Stormont gold district, Guysboro county, Nova Scotia. The nearby ten-stamp Mulgrave mill was also purchased, and since that time 974 acres of adjoining properties have been secured from the Government by direct lease. The property is served by a motor road and is about two miles from the village of Goldboro, situated on the shore of Isaac's harbour. The bulk of ?the supplies are brought in by coastal steamer from Halifax, a distance of about 100 miles, since the nearest railway connections are at Antigonish, some 40 miles distant. EARLYY WORK The Seal Harbor properties include the old Partington and Beaver Hat mines. A small tonnage of ore was mined from each and treated on the properties in stamp mills, which were later torn. down . A survey of old records shows that this ore averaged about $8.00 gold per ton. Development work by the present Company was confined to the 100-foot level until February, 1935, but after that rime the incline shaft was deepened to 425 feet and the 300-foot level was explored east and west of the shaft. Six belts of ore were intersected to the west of the shaft. The ore from these belts was hand sorted and the ore portion was put through the 10-stamp Mulgrave mill to defray operating expenses and to serve as a sample of the deposits. The average recovery per ton from this sorted ore was $6.10. Samples of the ore were sent to the testing laboratories of the Mines Branch, at Ottawa, and of Canadian Industries, Limited, at Toronto. Recommendations from both of these authorities were for removal of the coarse gold by concentration and barrel amalgamation, followed by cyanidation of the residue.

Jan 1, 1937

By A. O. Dufresne

A Step which, it is believed, will prove extremely beneficial to the Quebec asbestos-mining industry was taken during 1931, when the asbestos mine operators of the Province assembled to work out a uniform method of naming the products of their mines. The outcome of several meetings was the drawing-up of a classification which defined, limited, and designated anew the numerous grades of asbestos marketed. It entailed no drastic departure from the existing processes of grading, nor any revolutionary changes in methods of testing, but aimed rather to perfect existing methods. The classification proposed has been accepted by all operators in the Province, who, from January first of this year, began introducing the new nomenclature. Unless one is conversant with the properties and mode of occurrence of chrysotile asbestos, with the unique milling methods devised for its recovery, and with the history of the development of their technique, he may not readily understand the basis of the new classification. For information on these and other data concerning the industry, the reader is referred to a recent publication, Chrysotile Asbestos in (Canada, by James Gordon Ross, issued by the Mines. Branch of the Department of Mines, Ottawa. The object of this paper is to present briefly some of the phases in the evolution of the classification of Canadian chrysotile asbestos, in the hope that the recent effort to standardize the marketable products of one of Canada's most important non-metallic mineral industries will open a field for discussion, fruitful in new ideas and constructive suggestions. The necessity for the grading of asbestos results fundamentally from the fact that the price per ton depends on the length of fibre. At all times in the history of the industry, the very limited available supply of the longer grades, as well as the requirements of the trade, have caused relatively very high prices to be paid for fibre over half an inch in length, while for the shorter grades the price decreases rapidly, and at a rate which bears no proportionate relation to the length of fibre.

Jan 1, 1932

By E. Van Den Neste

A concise historical review is given of the Overpelt plant and the general principles of zinc hydrometallurgy are briefly outlined, together with a description of the new electrolytic zinc plant ore roasting process and, more particularly, the original Overpelt roasting process. A detailed description of the flowsheet of the zinc electrowinning plant, .with an annual capacity of 100,000 t, successfully put into operation in May 1974, is given. The treatment of the residues is performed following the goethite process ; the purification is continuous in two steps; the tank house is equipped with cells containing jumbo cathodes; the handling and stripping of the cathodes is fully mechanized. Concluding the description, some metallurgical and other features of the project are explained in detail.

Jan 1, 1977

By Claudia Gasparrini

"The ore microscope and electron microprobe, two common instruments for academic research, have not been used to full advantage in the Canadian mining industry, perhaps because they are not readily available to most mining companies.The present paper gives a description of the two instruments and of the manner in which, when used together, they contribute to the identification and description of mineralogical and metallurgical samples, and reviews the applications, to . date, in the mineral industry.The metallurgical applications can assist in determining the best separation technique for a particular metal or other economically important element, can provide explanations for poor recovery and/or liberation, can be used to determine theoptimum concentrate grade and can indicate environmental problems that may arise from the extraction process.In certain cases, the use of the two instruments may assist in the evaluation of new mineral deposits and in the determination of the origin of mineralization.IntroductionThe ore microscope and electron microprobe, two widely used instruments in universities and other research institutions, have not been exploited to their full potential by the Canadian mining industry.High-magnification, high-resolution ore microscopes, owned by most Canadian universities and government mining branches, are not widely used by mining organizations. The situation is very much the same with the microprobe. The geology departments of several major Canadian universities have easy access to this instrument. Fifteen of them, to the author's knowledge, own one and a few have already acquired or are planning on acquiring a second and later model. The mining branches of the Canadian Government have similar easy access to microprobes, as at least four of these instruments are available to them in Ottawa alone. The mining companies, on the other hand, except for the few larger ones which have their own research laboratories, have not been able to take advantage of electron microprobes in the past.This failure to exploit good ore microscopes and electron microprobes has been mainly due to a lack of expertise in the use of the two instruments for the study of metallurgical problems related to ore mineralogy. Government institutions providing research and test work to the industry are few in number, and are not always equipped with these instruments or are not geologically-oriented. Information provided on a consulting basis by universities and by government mining branches is normally limited, and frequently is not oriented to the needs of the mining company."

Jan 1, 1980

By M. H. Fathi

The aim of this work was to prepare the metallic coatings on 316L stainless steel dental implant and evaluate the corrosion characteristics and thus the biocompatibility of the uncoated and metallic coated dental implants and comparison of the effect of the type of coatings on biocompatibility. Three types of metallic coatings including Tantalum, Niobium, and Titanium coatings were made using physical vapor deposition process on 316L stainless steel dental implant. Structural characterization techniques including; X-ray Diffraction, Scanning Electron Microscopy and Energy Dispersive X-ray Analysis were utilized to investigate the microstructure and morphology of the coatings. Electrochemical potentiodynamic tests were performed in two types of physiological solutions at 37±1 °C in order to determine and compare the corrosion characteristics. All three types of metallic coatings had a positive effect on improvement of the corrosion behavior so that the coatings could increase the corrosion resistance of 316L stainless steel and this trend was independent to the type of physiological environment. Biocompatible metallic coatings could decrease the corrosion current density that is a distinct advantage for prevention of ion release. This can improve the biocompatibility of the implant and, consequently prevention of tissue damages, inflammation and irritation and obtained desirable histopathological response.

Jan 1, 2007

By Frank W. Cole, Sharanjit S. Dhillonn

A new method has been developed for calculating flowing bottom hole pressure in a gas well, using as a basis the general energy equation. Fundamentally, the method shows that a plot of flowing pressure versus depth for a gas well can be represented as a series of incremental .straight lines, with the accuracy in-creasing as the number of increments increase. It is shown mathematically that for most cases the slope of the flowing pressure versus depth curve is essentially constant, in which case a single calculation based on surface conditions will yield acceptable results. In all cases studied no more than two iterations were required for very good accuracy, and in most cases only one iteration was necessary. Several example calculations are shown and the results are compared to other commonly used methods of calculating bottom hole pressures These examples show that the method provides answers which are at least as accurate as other methods usually used, and results in a considerable reduction in computation time.

Jan 1, 1960

By W C. Shakespeare

The Ontario Committee on Taxation is making a comprehensive study of taxation in the Province of Ontario, and in this connection has received representations concerning mining taxation from a number of interested parties. Some of the more important recommendations on mining taxation are reviewed in this article. Introduction FOLLOWING the appointment of the Federal Royal Commission on Taxation, the Ontario Government, effective in November, 1962, appointed the Ontario Committee on Taxation to review taxes and revenues available to the Province of Ontario and its local governments, to co-operate with the Royal Commission on Taxation and with any other bodies of enquiry appointed by other provincial governments, and to make such recommendations as it sees fit to the Prime Minister of Ontario and the Executive Council. The members of the Committee are: MR. L. J. SMITH, F.C.A., Toronto, (Chairman) MR. ERIC HARDY, Toronto DR. R. CRAIG MCIVOR, F.R.S.C., Hamilton MR. CARL A. POLLOCK, Kitchener MR. R. BREDIN STAPELLS, Q.C., and Toronto. Like its Federal counterpart, the Royal Commission on Taxation, the Ontario Committee has held public hearings, has received written

Jan 1, 1965

By C. M. Díaz, P. J. Mackey, P. Coursol

In a recent paper [1], the present authors discussed calculated energy consumption numbers in copper sulphide concentrate smelting for four different smelting technologies. For the present study, from among these technologies, they selected the Noranda/Teniente continuous bath smelting followed by Peirce Smith (PS) converting route to investigate the impact on total energy requirement of some key process variations, such as tuyere injection of dry concentrate vs. slingering of wet concentrate over the molten bath, continuous converting vs. conventional batch PS converting and commercially proven slag cleaning alternatives. In their calculations, the authors used the same thermochemical model and methodology used in their earlier paper. This approach to explore plant design options provides an interesting basis for evaluating flowsheet modifications that could lead to significant copper smelting energy savings. The METSIM software was used in the present paper to carry out heat and mass balance computations for 8 different flowsheet configurations. The results are presented and discussed in the paper with respect to copper recoveries, energy requirements and CO2 emissions.

Jan 1, 2011

By S. Setayeshgar

The identification of potential accidents on construction sites has been a major concern in the construction industry and it needs a proactive safety plan to reduce the risk of accidents. There are no efficient methods for checking if safety measures are taken properly on construction sites. Consequently, workers on site are not given enough awareness about dangerous areas. In addition, construction sites are dynamic and on-site situations are changing in terms of permanent and temporary structures and facilities. This information can be represented using Building Information Modeling (BIM). This paper proposes the integration of BIM and safety risk analysis by considering the risk levels associated with the work spaces of different construction tasks. Work spaces are generated in a BIM model according to the Work Breakdown Structure (WBS) of the project, reference objects in the BIM, and the schedule and resources of the task. Each work space is assigned to one or more tasks or functions, e.g., work spaces for specific tasks, shared spaces (paths), storage spaces, or spaces prohibited to workers. The assignment of work spaces is based on the workers, equipment and materials involved in the task. All the work spaces are associated with a specific duration according to the schedule of the project. Then risk evaluation of the construction site is applied in order to evaluate safety risks based on their severity and the degree of exposure of workers. For example, work spaces for storing hazard materials and for heavy construction equipment have higher risks than other work spaces. The results of the risk evaluation can be visualized in a 4D BIM model.

Aug 1, 2013

By L. Yuan, J. H. Rowland, R. A. Thomas, D. Bahrami, G. P. Cole

"The past several decades have seen a steady increase in the use of atmospheric monitoring systems (AMS) in underground mines as sensor technology has advanced and costs for this technology have decreased. The AMS is a reliable tool for early mine fire warning by detecting gaseous products of combustion in underground mines. During a mine fire emergency, mine decision makers rely heavily on the prompt and accurate knowledge of the ventilation and fire situation in the mine, such as fire location, fire size, and the spread of smoke to make effective and efficient decisions on firefighting strategies and miner evacuation. Meanwhile, a prediction of the potential for fire development at a later time, such as whether the currently designated mine escapeways will be contaminated by smoke and toxic gases with the progress of the fire, is critical for effective decision-making to save lives that are in danger. The AMS monitoring data, including carbon monoxide (CO) concentration, airflow rate, smoke, etc., can provide information as to whether the smoke has reached the locations where AMS sensors are installed and if a mine-wide smoke spread has occurred. The National Institute for Occupational Safety and Health (NIOSH) has undertaken a task to integrate real-time AMS monitoring data with the mine fire simulation program, MFIRE, to simulate and predict the spread of smoke and toxic gas in a ventilation network based on the real-time AMS data. This paper reports the developed real-time method for characterizing the size and location of an underground mine fire and for predicting the spread of contaminants throughout the mine ventilation network using sensor data from the AMS.INTRODUCTIONNIOSH conducts research to develop workplace solutions to improve detection of and reduce the risk of hazardous conditions in underground mines. The advancement of senor technology and the increasing demand for real-time mine parameters monitoring have led to extended applications of atmospheric monitoring systems (AMS) in underground mines worldwide. In the United States, AMS is primarily used for early mine fire warning by detecting carbon monoxide (CO) in fire hazard areas, such as belt entries. Mine fires can grow rapidly, and time is the critical element. Prompt detection, timely and accurate warnings to those miners potentially affected, and a proficient response by underground miners can have a tremendous impact on the social and economic consequence of a small underground mine fire (Conti et al., 2005). The early detection of a mine fire could gain time for the first responders to put out the fire before it develops into a disaster. An AMS system with CO sensors has especially played an important role in the early detection of mine fires. The continuous monitoring of an underground mine atmosphere with an AMS could generate a large amount of data in a mine fire event. However, the current application of AMS is mainly limited to sending out an alarm when monitored CO concentration exceeds a certain level. An opportunity arises as to whether these data can be further used in fire emergency response. In order to make effective decisions on firefighting strategies, mine workers’ seeking refuges, evacuation and escape, and the timing on when to send rescuers, decision makers need accurate and timely knowledge of the ventilation and fire situation in the mine. Information about the fire intensity, where in the mine the smoke and toxic gases have spread, and whether designated mine escapeways have been compromised by smoke and toxic gases from the fire would greatly increase the effectiveness of these decisions. However, the monitored AMS data only provides atmospheric conditions in the vicinity of sensor locations. What is concluded from the monitored AMS data highly depends on the decision makers’ capability and experience. Predictive insight into fire growth and smoke transport would greatly help decision makers during a fire emergency."

Jan 1, 2019

By L. S. Beck

"The Athabasca region forms part of the Churchill province of the Canadian Shield and is underlain by an Archean or Aphebian assemblage of rocks that underwent severe metamorphism and granitization during the Hudsonian orogeny (1750-1950 m.y. ago). In places, the eroded orogen is overlain by unmetamorphosed cover rocks (in-cluding the Martin and Athabasca formations) of probable Paleohelikian age. Basic dykes cut all the rocks of the region.There are innumerable vein-type pitchblende deposits and many syngenetic occurrences of uraninite in crystalline basement rocks. Evidence is presented to show that pitch-blende was emplaced during the final stages of the Hud-sonian granitization and followed the crystallization of syngenetic uraninite transitionally. In terms of P-T condi-tions, the pitchblende deposits belong essentially to Lindgren's mesothermal group.Based on the postulated uranium metallogenesis, the possibilities of finding further deposits of pitchblende and other types of uranium deposits are discussed."

Jan 1, 1970

By J. D. McFarlane, V. Robinson

"The paper begins with a brief account of the naturarly occurring resources of gypsum and anhydrite and a discussion of their relative value and utility as sources of sulphur. The fundamental chemistry of recovering sul-phur values from calcium sulphate is discussed. (a) Thermal decomposition -discussed as impracticable; (b) Reduction to calcium sulphide; (i) Total Reduction-The chemistry is outlined and the Dorr-Oliver and Bureau of Mines processes mentioned. The Elcor process is mentioned and certain deductions made from available information.(ii) Partial Reduction-This is stated as the basis of the only proven process, namely ""The Cement -Sulphuric Acid Process."" The possibility of recovering lime is mentioned as an aside, but dismissed for lack of commercial application. The history of the cement -sulphuric acid process is covered briefly and a list of plants in commercial operation included. A brief elementary account of the basic chemistry of cement production is followed by a discussion on raw materials and fuels. A short account of the flow scheme of a typical plant, with notes on the operating peculiarities, precedes an account of product quality. The latest developments which enable by-product gypsum to be used as a raw material are discussed, with an indication of how the flow scheme is modified. A statement of feasible plant capacities is followed by requirements of raw materials, services, labour, etc., and finally some indication is given of capital costs."

Jan 1, 1969