Search Documents

By P. Leo

The Al-Zn-Mg alloys (e.g. 7004, 7020) are employed for land transport and architectural applications whereas the Al-Zn-Mg-Cu alloys (e.g. 7075, 7050) provide the high strength aircraft alloys. The Cu gives rise to suitably sized and distributed precipitation but causes high quench sensitivity. Their hot work processing also has marked differences; the Cu-free alloys have good extrudability whereas the Cu-bearing alloys have low extrudability and are difficult in rolling as well. The behaviors of the two classes are described in terms of flow stresses and ductility over 300 - 500°C, along with constitutive contrasts. The ductility of the alloys with Cu is much reduced above 400°C by precipitation of a phase at the grain boundaries that can be avoided by suitable heating schedules. The high strength alloys are subject to de-lamination corrosion of sheared edges due to severely pancaked grains; this can be alleviated by holding between passes, in mid-rolling schedule. In torsion tests at 10-1 to 10 s-1/ 250 - 500°C, the stresses (ductilities) at 300°C/ 1s-1 and activation energy Q for 7004 were 118 MPa (2) and 262 kJ/mol. The 7075 was tested after several pretreatments: completely over-aged (softened): 107 MPa (5), Q=150 kJ/mol; whereas, solution and quick cooling to testing caused extraordinarily high peaks related to dynamic precipitation resulting in 160 MPa (1.2), Q=300 kJ/mol.

Jan 1, 2011

By R. J. Johnston

"INTRODUCTIONPoint Mines is located about 65 miles east of Hay River on the South Shore of the Great Slave Lake. It is connected to the Northern Alberta Railway System by the Great Slave Lake Division of CN Railways at Roma Junction, Alberta.The operation started in the fall of 1965 with a capacity of 5000 t.p.d. An addition was put into operation late in 1968 to bring the capacity up to 8000 t.p.d. The present milling rate is 11,000 t.p.d.The location of Pine Point Mines is such that long end cold winters are to be expected end temperatures of lower than -200F are encountered from late October to late March, with extended periods of -300F being common in January and February.It was recognized by Cominco engineers during the initial design period that since freezing would be encountered with open pit ore somewhere in the crushing circuit, the problem was to reduce it as much as possible. Other mines, working under similar conditions, found that the fine ore bins feeding the grinding circuit were the main problem area. The decision was reached, therefore, to have heated fine ore bins and to make sure thst the ore was sufficiently warm to prevent freezing.CRUSHING PLANT FLOWSHEETThe crushing plant has a standard open flow circuit (flowsheet). Ore from the stockpile is loaded into R-50 Euclid trucks by Caterpillar 992 Front End Loader with 11 cu. yd. bucket and dumped into a 42 x 65 C.A.C. Superior Crusher driven by a 300 HP motor. The crusher is set at a nominal 5 inches. The ore falls through into a 100-ton surge bin. There are high level and low level nuclear gauges to allow the primary operator to optimize for optimum orientation."

Jan 1, 1972

By P. Desclaux, A. Gosselin

"In 1999, PFC measurements were carried out at Alcan smelters as part of a large measurement campaign led by the Canadian Aluminium Association. Side worked prebake (SWPB) and horizontal stud Söderberg (HSS) plants in Arvida were the selected sites. CF4 and C2F6 emissions were measured continuously in the exhaust duct and at the roof vents for a week. In parallel, voltages from four designated cells were recorded at a high scan rate. Results were analyzed and correlations between voltage, anode effect duration and PFC emissions were tested. Some fundamental anode effect mechanisms were proposed and validated with the observations. IntroductionFollowing the international agreement reached within the scope of the Kyoto protocol, voluntary partnerships have been established in many countries especially for the aluminum industry. It is well known that the PFCs that are periodically emitted during aluminum production are the major source of fluorocarbon emissions. The latter are part of the greenhouse gases. In the fall of 1999, Alcan announced that it will adopt, promote and regularly renew a long-term greenhouse gas management commitment at all of its facilities within the framework of the so-called TARGET program that was implemented during 2001. The program is intended to produce on-going reductions, which will be reported publicly on an annual basis.Improvements in the understanding of the mechanisms leading to PFC emissions will contribute to targeting the most appropriate reduction actions. PFC measurement campaigns have been driven toward this end. The first measurement campaign was conducted in 1993 in order to get a picture of the emissions and a base line. The last measurement campaign was conducted in 1999 and its main objective was to compare current emissions with those measured in 1993 and to confirm the accuracy of the predictive equations for the calculation of PFC emissions. This campaign has been conducted by the Canadian Aluminium Association and measurements were made in plants using different technologies. Results of this campaign have already been reported by Bouchard et al. (2001)."

Jan 1, 2002

By Unknown

We are indebted to the Consolidated Mining and Smelting Company of Canada Limited for the several pictures in this issue showing the progress made in new construction at Tadanac and at Bonnington Falls, B.C. Plate No. 1 shows the down-stream side of the No. 1 hydro-electric station of the West Kootenay Power and Light Co. Limited at Bonnington Falls, on the Kootenay river, at which 17,500 k.v.a. will be developed to meet the requirements of the enlarged zinc and lead refineries at Tadanac. The generators, exciters and switch apparatus were supplied by the Canadian General Electric Company and the step-up transformers by the Canadian Westinghouse Company Limited. The plant throughout was designed, manufactured and erected by Canadians. Plate No. 2 shows the casting room of the new lead-plant and plate No. 3 the new tank-room of the electrolytic lead refinery at Tadanac. These additions will increase the capacity of the lead refinery by some 150 tons daily. The extensions also include practically doubling the zinc plant, and the gold and silver refineries. With the exception of the new stack, all designing construction and installation of the various plants is being done by the Company's own employees at Tadanac. Plate No. 4 shows the progress made in the construction of the new reinforced concrete stack at Tadanac. This stack, of 21 feet inside diameter at the top, will be brick lined and when completed will rise 400 feet above its foundations: the tallest of its kind in the world. The construction is in charge of the Rust Engineering Company of Pittsburgh, Pa. Plate No. 5 is a panorama of the Tadanac smelters and refineries. The photograph was taken from the roof of the lead smelter and gives an excellent idea of the size of the plant and its surroundings. Tadanac produces electrolytic lead, zinc and copper and fine gold and silver. During 1924 the company treated 1,333,523 tons of ore and produced: 161,400,- 769 pounds of lead; 92,197,824 pounds of zinc; l,382,750pounds of copper; 4,074,044 ounces of silver, and 26,976 ounces of gold.

Jan 1, 1925

By Shen Zhengchang, Dong Ganguo, Chen Dong, Zhang Ming

"It is advantageous to process low grade ores with large scale flotation cells. Large-scale flotation cells have been enhanced with effective volume scale-up. In this paper, the latest and largest flotation cell with effective volume of 680 m3 in China is investigated. The hydrodynamics and flotation kinetics characteristics are conducted using CFD simulation. The similar circulating flow is formed compared to the previous BGRIMM (Beijing General Research Institute of Mining and Metallurgy) flotation cell and it is a suitable fluid dynamics environment. It is demonstrated that the flotation cell produces good gas dispersion and solid suspension. It is indicated that kinetic eddy dissipation plays a key role on collision kernel and collision probability profile. The higher collision probability profile appears at the impeller and stator regions aiding good metallurgical performances. The properties of the large-scale flotation cell are assessed using hydrodynamic numbers. The variation of hydrodynamic numbers such as the power number Np, the Froude number Fr, the air flow number Na, etc with flotation cell volumes show similar properties to previous flotation cells proven to be good in engineering applications. This research would aid structure optimization of the 680 m3 flotation cell.INTRODUCTIONFroth flotation is one of the mains method used in the mineral industry, which is used to process the most of metallic minerals. The proportion of low grade ores has increased with the minerals exploited around world. The increased capacity of concentrators demands large-scale flotation cells. Therefore, flotation equipment has seen a significant increase in size, for which large-scale flotation cells have prominent advantages in improving metallurgical performances, reducing area of plant blueprint printer, lowering the power consumption of the unit ore, decreasing labor cost and overall capital cost. Since the end of 1940’s, flotation cell sizes have continuously increased. To the end of 1990’s, flotation cells with the effective volume of 200 m3 were developed. In the last two decades, flotation cells have achieved a dramatic increase in size. In 2003, an industrial experiment on 257 m3 Smart Cell flotation cells was carried out in Minera Los-Pelambres, Chile. In 2007, the first 300 m3 Tank Cell flotation cell was designed and obtained industrial application in Macraes gold ore, New Zealand. And 320 m3 BGRIMM flotation cells are also in good operation in Toromocho Copper Mine, Peru and Wunugetushan Copper Mine, China. However, flotation cells are conventionally designed using empirically derived relations and geometric similarity. The continual scale-up of flotation cells is still a significant developing process. A 500 m3 Tank Cell was designed for the industrial experiment in Finland and a 620 m3 Tank Cell have also been completed the design. A 660 m3 Super Cell also was manufactured for the industrial experiment released in IMPC 2014. So, the flotation cells with volume exceeding 600 m3 become a pioneering research field for researchers worldwide."

Jan 1, 2016

The current mining operations at Newmont Boddington Gold Mine (NBG) commenced in 2008, and commissioning of the processing plant started in the latter half of 2009. Metso Process Technology and Innovation were engaged to assist NBG with commissioning and project ramp-up through the implementation of a comprehensive ?Mine-to-Mill? Process Integration and Optimisation project. This methodology entailed extensive data collection which included drill and blast audits, ore characterisation, comprehensive comminution circuit surveys and review of operational data to assess the limitations within the current mining and processing operations. The results of these investigations have been used to define the operating base line of both the mining and processing areas and identify improvement opportunities. The use of modelling and simulations, utilising actual production data, has allowed for multiple scenarios to be evaluated, minimising the requirement for actual trials and thereby minimising impact on the operation. Improvements implemented to date include: the introduction of routine rock strength measurement for inclusion in block models, modifications to blast design improving ROM fragmentation and downstream comminution process performance, and changes to improve performance of secondary crushing and grinding circuits. Close cooperation between the mine and plant personnel is playing a significant role in overcoming the challenges presented to this operation and further improvements are targeted for the second full year of process plant operation.

Jan 1, 2012

By Biplop Das, E. Herrera, A. Burrows, P. J. Mackey, G. R. F. Alvear Flores

Since the first commercial plant was built at Mount Isa, another twenty ISASMELT™ furnaces have come into commercial operation, and construction of new plants continues. The primary copper ISASMELT™ top submerged lance (TSL) technology continues to attract interest from potential users who seek to smelt productively. In addition to the known benefits of productivity and flexibility, ISASMELT™ operators have also achieved improvements to energy efficiency when switching from their previous technologies. The recent production statistics for operation at Tuticorin, India show that ISASMELT™ has taken the first steps into territory beyond 400,000 t/y (copper cathode basis) and this will likely be the scale chosen by future new copper smelters operating purely on a toll smelting basis. Highly energy-efficient technologies will be expected at these smelters

Jan 1, 2015

By J M. Fletcher

The responsibility and scope of the Industrial Engineering Department, as organized at the Jeffrey mine, has been broadened to include any study, project or report that could result in more effective use of men, materials and equipment. Although still emphasizing wage incentives and co t reduction, much more varied work is now done, consistent with the in-.creased complexity of industry. Additional activities now include production, maintenance and inventory control improved job evaluation, packaging, labour utilization studies, technical sales liaison, mining, milling and service department n1ethods, plant layout, and specialized project analysis. Additional techniques include the extensive use of work .sampling and standard data. A recent trend has been toward increased emphasis on industrial relations, both in introducing change to the men and in providing requested explanations to Union stewards and officers. These new responsibilities have resulted in the development of specialists in some rather narrow industrial engineering fields, as well as the necessity for industrial engineering assistance in supervisory and job training.

Jan 1, 1963

By X. (Mike) Yao

Rock mechanics engineers must provide ground support designs that ensure a safe underground working environment. Unexpected falls of ground are unacceptable while ground support systems must be adequate. Ground support must be economic for the area supported and the time frame the opening is in use. While numerical modeling can be used for ground support design, empirical models are still the common useful design tools. Empirical models are best developed and improved from local experiences although some models, such as Stability Graph (Potvin et al, 1992), are in extensive use by the Canadian mining industry. To determine the adequacy of ground support practices at HBMS, a database of 50 fall of ground case histories between 1985 and 2001 was compiled. For each failure, the recorded data included: location, rock type, rock mass conditions, opening and failure geometry, installed ground support and failure mechanism. An analysis of the database was done to obtain an understanding of failure frequency association with rock types, stope geometry and installed ground support, and to assess what support design changes were necessary. The paper describes changes made to ground support and mining practices during the last five years, and the formation of new ground support standards and practices which have been successful in reducing ground falls while providing improved, efficient and economical ground support.

May 1, 2002

By Hugh P. Godard, K. Winslow

"AbstractA number of panels of various aluminum alloys in different combinations and secured by steel and three types of aluminum rivets were exposed underground at two locations in a Northern Ontario gold mine for two years and then examined to determine the extent of corrosion. The results indicate Alcan 65S-T to possess considerable advantages over Alcan 178-T, which has been employed in the construction of light skips and cages with considerable success for almost twenty years. Information on the behaviour of these alloys when used with steel rivets and in mixed combinations with themselves was obtained.IntroductionBy the complete substitution of aluminum alloys for steel in the fabrication of mining skips and cages, their weight can be reduced as much as 50 per cent. Lesser savings are possible though its savings are possible through its plates, doors, reinforcing members, etc. Reduced weight leads to economy through increased hoisting efficiency.For a new installation, the basis of design is the rate of production, which thus fixes the live load to be hoisted per trip. A lighter skip permits the use of a lighter rope and a smaller hoist. In deep shafts with high-speed hoists operated in balance, the power required for accelerating is considerable. The hoist size is determined by the weight of skip, load, and rope plus the force required to accelerate or decelerate these three elements A light skip may result in a considerably lighter rope. This is important because, even though the skip can be completely balanced this is not true of the rope. Partial balancing is possible, but conical hoist drums or other devices for this purpose are costly; thus a smaller rope results in a smaller hoist, with consequent general reduction in cost of the whole installation. A reduction in power consumption is also obtained as a result of keeping to a minimum the amount of unbalanced load and the weight of all moving parts which must be accelerated."

Jan 1, 1950

By A. K. Croteau

"At Craigmont Mines Limited, Merritt, B.C., the mining practice of trackless sub-level caving was started in the latter part of 1966. This type of mining was new to the mine personnel and the mining industry of Canada as a whole. Sub-level caving has presented many old and a number of new problems in maintaining the equipment used in this method. This paper will deal with some of these problems as they affect this particular mining operation. It will be impossible to review all phases of the equipment, but an attempt will be made to cover the most pertinent aspects in maintaining the drilling, mucking and hauling, and auxiliary equipment."

Jan 1, 1970

By Jean-Paul Drolet

"The ultimate aim of the Law of the Sea Conference, held under the auspices of the United Nations, is to ensure that all aspects of the use of the sea are covered by international law. The question facing the nations of the world can be stated as: "" Who will control and benefit from the use and the wealth of the sea?""The United Nations Conference on Law of the Sea - known as UNCLOS - which reconvened in New York during the latter part of August 1978 was the third such Conference in the UN's history. The concepts of sovereignty over the territorial sea and freedom on the high seas have remained fundamental to the international law o f the sea until our time. The legal regime based on these two concepts developed initially from state practice meant that the unilateral actions taken by one or more countries were eventually accepted and followed by others.It was not until 1958, during the first Geneva Conference on the Law of the Sea (pursued in a second Conference in 1960) that the Law of the Sea was codified and modified to a certain extent by the then independent nations of the world in the four multilateral conventions on territorial sea and contiguous zone, continental shelf, high seas, and fishing and conservation of living resources.A third Conference got under way many years later when the members of the UN met in New York at the end of 1973 for preliminary discussions . This meeting stemmed largely from the need to fill gaps in existing international legislation which did not cover the new uses of the sea. The Conference was subsequently reconvened a number of times - in Caracas (1974), in Geneva (1975) and twice in New York (1976) for what was called "" substantive negotiating sessions."" A sixth session was held in New York in 1977; a seventh, held in Geneva at the beginning of 1978, recessed and reconvened in New York at the end of August 1978. This is what is referred to, in international jargon, as the seventh session of the Third United Nations Conference on the Law o f the Sea. The following dates are the principal markers of a saga which began some twenty years ago with the purpose of regulating the use of the oceans."

Jan 1, 1981

By H. J. McQueen

About 1973 the abrupt decrease in crude oil shipments due to political action by Middle Eastern suppliers, caused a shortage and a steep price rise. In response, Canada had to develop strategies of diminishing consumption and increasing production in both traditional and environmentally friendly resources. To clarify the situation in Canada, there are brief histories of energy (discovery, pipelines), manufacturing and science development, 1800-1970. Energy strategies, both nationally and in Quebec, succeeded in curbing consumption and in expanding production while fostering research in renewable sources. The industry-sector committees provided free exchange of conservation techniques through the federal energy ministry, with progress reports issued annually. Pipeline history in North America is reviewed along with manufacture and construction plans in Canada. Considerable success in all the aspects provided long lasting benefits, but after the embargo was lifted, many research initiatives were gradually abandoned for political reasons. Sustainability is the goal; society must conduct conserver analysis, legislation and action to enhance it.

Jan 1, 2015

By B. van Beek, T. Goff, P. Gebski, P. Szyplinski, W. L. Ying

"Monitoring the refractory lining integrity is essential to assure the safety of the operators and to determine the remaining campaign life of a furnace. Early detection of refractory lining degradation is essential to avoid sudden furnace failures and prevent unscheduled shutdowns. In the mid-1990s a stress wave propagation technique was developed and since then it has been utilized by Hatch Non-Destructive Testing (NDT) Group to evaluate furnace linings. For the last 17 years the AU-E technique evolved in terms of hardware, software and signal acquisition and interpretation. Most importantly, based on more than a decade of commercial applications, an extensive database of various failure modes, refractory deterioration trends and material properties has been created. This knowledge base is an integral part of AU-E which progressed from a NDT technique towards a comprehensive approach for furnace condition monitoring. All of the improvements introduced over the last several years have greatly improved the accuracy of the measurements. The data analysis process has also become more time efficient making the critical results available to the furnace operators in a more timely manner. Today the AU-E technology is used on a variety of process vessels in non-ferrous, glass, chemical and iron and steel industries.In this paper we are reviewing the available techniques for furnace refractory lining measurement and discussing the pros and cons of each method. The need for continuous improvement and development of new techniques for refractory monitoring is also emphasized. Finally, we are presenting a number of case studies and comparisons between the physical verifications and the AU-E measurements."

Jan 1, 2015

By Adrian Dance

Newmont Ghana Gold Limited?s Ahafo operation have been working with Metso Process Technology & Innovation (PTI) since early 2009 to increase mill throughput from a combination of controlled blasting practices and optimised primary crusher and grinding circuit conditions. For such Mineto- Mill projects, PTI?s methodology is termed Process Integration & Optimisation (PIO). Ahafo operate a SAG mill, ball mill and pebble crusher (SABC) circuit that processes a range of primary ore of varying hardness from different pits which is blended with soft oxide material. The PTI study focussed on ball mill limited material from the Apensu open pit. Following a benchmarking study of all blasting, crushing and grinding practices in January 2009, PTI recommended changes in both blasting and crushing conditions in order to generate a finer feed size to the SAG mill. Additional operating changes in the grinding circuit were recommended. A series of trials were conducted in November 2009 where three blasts were fired using a different blast design (hole diameter and explosive type) in the same area of the Apensu pit as the benchmarked material in January 2009. Top and bottom benches (or flitches) from each blast were sent exclusively to the grinding circuit and the material was tracked using PTI?s SmartTag? system. The results from the six trials showed a significant increase in primary ore throughput at a reduced blend of oxide material. Ahafo have since standardised on these modified blasting conditions for all Apensu ore zones and have been able to sustain higher throughput compared to historical performance on similar material. This paper summarises the phases of the PIO project, the changes made in operating practices and the outcomes of the blasting trials that validated the predicted increase in mill throughput.

Jan 1, 2012

By D. D. Tannant

An experimental and numerical study was conducted on the geomechanical behaviour of oil sands during penetration tests in which a steel wedge with an apex angle of either 20 degrees or 30 degrees was forced into compacted oil sands. The boundary conditions simulated in the laboratory tests are similar to shovel penetration into oil sands. The objective of the laboratory tests was to measure the force required to push a steel wedge into compacted oil sands. A wedge penetration test differs from conventional triaxial tests in that much more shear is generated. The laboratory data was needed to improve calibration of micro-mechanical input parameters for a two-dimensional discrete element model of oil sands constructed with Particle Flow Code (PFC). Initial model calibration was performed with triaxial test data and then a PFC model of the wedge penetration test was constructed. The measured force-displacement behaviour of the steel wedge was compared with PFC modelling results. It was found that different combinations of PFC particle and bond parameters could equally well replicate the laboratory triaxial compression data for bitumen-rich oil sands. When the wedge model was run, it was found that the resulting force required to penetrate the wedge into the oil sands was about four to six times higher than that measured. This clearly indicates that further research is required to improve the predictive capability of PFC models of oil sands.

Jan 1, 2002

By F. F. Roberto, E. Kirby, A. R. Marchbank

The application of biologically assisted methods for metal extraction in the mining industry has a long history, but development of modern techniques has been relatively slow. There is, however, a resurgence of interest in the industry with the recent development of methods to successfully treat base metals concentrates. Two major pilot plant programs for treatment of chalcopyrite concentrates have been initiated in the past year and results from one are beginning to be released. This paper provides an overview of methods that have been applied in the past, from the earliest deliberate applications of the technology, through the copper and uranium heap and dump leach applications, the more highly engineered agitated tank leach gold applications and the developments currently taking place in the industry.

Jan 1, 2003

By G. M. Card, K. D. Card, B. V. Sanford

Abstract-The Canadian Shield and its extensions are traversed by an orthogonal system of northwest and northeast trending arch-style uplifts. These basement arches were formed by repeated vertical movements along pre-existing structures during compressional and extensional tectonism connected with events in surrounding Proterozoic and Phanerozoic orogens and ocean basins. The arches influenced patterns of sedimentation and tectonism in the intervening epicratonic basins and marginal platforms throughout the Proterozoic and Phanerozoic. Movements on the arch structures also triggered minor magmatism and controlled the location and timing of alkalic rock-carbonatite, kimberlite, and related intrusions in the Canadian Shield, the Western Canada Sedimentary Basin, and West Greenland.

Jan 1, 1997

By G. M. Card, K. D. Card, B. V. Sanford

The Canadian Shield and its extensions are traversed by an orthogonal system of north-west and northeast trending arch-style uplifts. These basement arches were formed by repeated vertical movements along pre-existing structures during compressional and extensional tectonism connected with events in surrounding Proterozoic and Phanerozoic orogens and ocean basins. The arches in?uenced patterns of sedimentation and tectonism in the intervening epicratonic basins andmarginal platforms throughout the Proterozoic and Phanerozoic. Movements on the arch structuresalso triggered minor magmatism and controlled the location and timing of alkalic rock-carbonatite, kimberlite, and related intrusions in the Canadian Shield, the Western Canada Sedimentary Basin, and West Greenland.

Jan 1, 1997

By Frederick W. Breaks, Andrew G. Tindle, Julie B. Selway

"Abstract - Rare-element pegmatites may host several economic commodities, such as tantalum (Taoxide minerals), tin (cassiterite), lithium (ceramic-grade spodumene and petalite), and cesium (pollucite). Key geological features that are common to pegmatites in the Superior province of Ontario and Manitoba, Canada, and in other large tantalum deposits worldwide, can be used in exploration.An exploration project for rare-element pegmatites should begin with an examination of a regional geology map. Rare-element pegmatites occur along large regional-scale faults in greenschist and amphibolite facies metamorphic terranes. They are typically hosted by mafic metavolcanic or metasedimentary rocks, and are located near peraluminous granite plutons (A/CNK > 1.0). Once a peraluminous granite pluton has been identified, then the next step is to determine if the pluton is barren or fertile. Fertile granites have elevated rare element contents, Mg/Li ratio < 10, and Nb/Ta ratio < 8. They commonly contain blocky K-feldspar and green muscovite. Key fractionation indicators can be plotted on a map of the fertile granite pluton to determine the fractionation direction: presence of tourmaline, beryl, and ferrocolumbite; Mn content in garnet; Rb content in bulk K-feldspar; and Mg/Li and Nb/Ta ratios in bulk granite samples. Pegmatite dikes with the most economic potential for Li-Cs-Ta deposits occur the greatest distance (up to 10 km) from the parent granite.Metasomatized host rocks are an indication of a nearby rare-element pegmatite. Metasomatic aureoles can be identified by their geochemistry: elevated Li, Rb, Cs, B, and F contents; and by their mineralogy: presence of tourmaline, (Rb, Cs)-enriched biotite, holmquistite, muscovite, and rarely garnet.Once a pegmatite dike has been located, the next step is to assess its potential to contain Ta mineralization. Pegmatites with the highest degree of fractionation (and thus the most economic potential for Li-Cs-Ta) contain blocky K-feldspar with >3,000 ppm Rb, K/Rb < 30, and >100 ppm Cs; and coarsegrained green muscovite with >2,000 ppm Li, >10,000 ppm Rb, >500 ppm Cs, and >65 ppm Ta. Pegmatites with Ta mineralization usually contain Li-rich minerals (e.g., spodumene, petalite, lepidolite, elbaite, amblygonite, and lithiophilite) and may contain Cs-rich minerals (e.g., pollucite, Cs-rich beryl). The ore minerals of Ta are commonly manganotantalite, manganocolumbite, wodginite, and microlite; Ta-rich cassiterite is also commonly present. Tantalum mineralization tends to occur in albitic aplite, mica-rich (lepidolite, cleavelandite ± lepidolite), and spodumene/petalite pegmatite zones."

Jan 1, 2005