Search Documents

By R A. Eggleton and, P de Caritat, K M. Scott

The Portia Au and North Portia Cu-Au-Mo prospects are located on a magnetic structure called the Benagerie Ridge Magnetic Complex, comprising varying pyrite-bearing Proterozoic albitite, phyllite and carbonaceous phyllite. The prospects are covered by up to 75 m of Cainozoic sediments, which comprise from top down, surface soils, Quaternary sediments, the Miocene Namba Formation and the (Late-Oligocene?) Portia Unit.The Portia Unit is dominantly clay-rich with local sand-rich base and it fills palaeo-topographic lows and a palaeo-valley that incised into the weathered basement rock (saprolite). This sedimentary unit hosts the majority of the Au grains found at Portia, with additional Au grains also present in the underlying saprolite. The North Portia prospect comprises saprolite hosted Cu-Au-Mo, with elevated concentrations of As-Pb-V present in the northern part of the prospect. These two groups of elements are delineated using factor analysis, and are regarded as the pathfinder elements for the North Portia mineralisation.Secondary Cu minerals including covellite and native Cu are present in the lower saprolite, and are stable under reducing conditions in the saturated zone.In the upper saprolite (unsaturated), Cu, Au, As, Mo and Pb are associated with Fe-oxides, mainly goethite and hematite. Saprolite leached of Fe generally contains low pathfinder elements concentrations.

Jan 1, 2004

By Zamora C

The performance of a system for detecting the onset of overloads on rod mills is described. The system has bee,, tested at CODELCO E1 Salvador Concentrator where, due t,, variations on size distribution of the copper ore feed, th' rod mill is frequently subject to overloads. The main inpur signal to the system is the rod mill sound, after being measured and analog conditioned. This signal and othe signals measuring the fresh ore feed and the mill watt addition are fed to a computer containing a simpl mathematical model. The model parameters are empiricall estimated and an analog output signal is generated, whic gives an early prediction of the overload condition. The experimental results described in this paper show that the overload condition may be predicted with an anticipation of about three minutes.

Jan 1, 1985

Grade control is an important factor in the on-going success of a mining operation. Grade control criteria will vary depending on the commodity being mined. Financial considerations determine the actual grade control criteria at any one mine site. Mining and metallurgical capital and operating costs are ultimately used in ascertaining cut-off grades employed in grade control. The metallurgical characteristics of the ore, and ultimately the equipment selection and design of the plant, are based on samples provided by the exploration geologist. Ore variability is an important factor in designing the process plant. Ore variations, outside of those catered for in the design, as well as large ore changes on a daily basis, will impact on the metallurgical performance, and hence the economics of a mining operation. Therefore good liaison between the grade control geologist and metallurgist will undoubtedly lead to a more consistent, and more profitable mining operation.

Jan 1, 1993

It may at first sight appear somewhat presumptuous for the writer to attempt to discuss a subject in which he cannot pretend to possess any special scientific training; but a sufficient apology can surely be found in the fact that a very large percentage of the accidents from explosives occurring in metalliferous mines is traceable to the ignorance of the characteristics of these compounds by the miners who have to handle them, and to their deliberate disobedience of the rules laid down for their guidance by the manufacturers, the government regulations, or the special rules of the mines.The only method which promises any possibility of improvement upon these conditions is to substitute reason and understanding for the rule-of-thumb principle which says "you should do this" or "you should not do that." In the one case his own knowledge and intelligence enables the miner to avoid any dangerous practice in the other his inclination prompts him to do anything which will save time, provided he is not found out or at best trusting to his memory to tell him what is dangerous, without the reasoning which makes that memory easy.Another evil of rule-of-thumb knowledge is that, from its very nature, it prevents adaptability, and so we find that old miners, who learnt blasting in the days of black powder, cannot understand why high explosives do not require heavy tamping, or because copper bars are permitted in tamping powder they should not be used with other explosives...

Jan 1, 1903

By Plyley WF

Kidston Gold Mine is a 3.5 million tonnes per year operation located 280 kilometres west of Townsville, Queensland. Kidston's ore body consists of 44.3 million tonnes graded at 1.79 grams per tonne gold and 2.22 grams per tonne silver. Full production commenced in March, 1985. During the remainder of 1985, Kidston milled 3.77 million tonnes of ore and produced 213,614 ounces of gold.The ore is comprised of granodiorite, polymictic and volcanic breccias. The degree of oxidation of the rock influences the milling capacity and therefore determines the cut-off grade; ore is categorised as oxide, transition and fresh. The milling rates are 15,400, 12,000 and 9,600 tonnes per day for oxide, transition and fresh ore respectively.The ore is treated in a conventional cyanidation/ carbon-in-pulp plant (CIP). The plant consists of a primary crusher, semi-autogenous grinding (SAG) and ball mills, leach circuit and carbon-in-pulp circuit. Carbon stripping and dore smelting are done on site. The major difference between the Kidston plant and other Australian CIP plants is that a cyclone separation and washing circuit rejects half of the dry tonnage as a sand tail prior to CIP treatment. This difference allows the CIP circuit at Ki.dston to be smaller and makes the CIP less sensitive to the grind circuit product size.

Jan 1, 1986

By Fengyan D

Removing the interference of latter events, the data of geophysical (such as gravity and aeromagnetic) anomalies may indicate whether the mobile belt exist and whether the adjacent terrains of the mobile belt originally belong to one single unit. The petrotectonic assemblage can provide informations about the tectonic setting where it was generated from. The structural style can exhibit the kinetic and kinematic processes. The form of ancient isogeotherm may reflect the ancient geothermal regime which is related to the tectonic mechanism. In general, the early Precambrian terrains suffered polymetamorphism and multiple structural deformation. The researches must be carried out for the distribution of paleogeotharm and m.tamo'phic facies and zones on the basis of recovering the early structural style with structural analysis method; then a relatively correct conclusion may be geined on the ancient geothermal regime. This method can be known as "Ancient Thermotectonic Analysis". Through the sythetical research, a real knowlege about the tectonic setting of early Precambrian mobile belt can be obtained.

Jan 1, 1990

By Juniper LA

ERM Consultants Pty Ltd was established in 1980 for the purpose of introducing a disciplined coal technology and power station planning service, to support Australia's efforts in establishing a major export steaming coal industry. At that time, major coal exploration programs were mounted on more than 50 potential export coal deposits with proven open-cut reserves to export 200 Mt/a of coal. The fact that Australia achieved an export trade of only 30 Mt/a, equivalent to the energy requirements for a population of around 5 million people, illustrates the very small achievement to date. The main reasons for this small export steaming coal growth have been: 1. Failure to convince potential overseas coal buyers of the benefits of coal-fired power generation, and the ability of proper power station design to overcome environmental problems, and achieve reliable operation and long life when burning Australian coals. 2. Failure to promote Australian power engineers to advise on the use of Australian coals, resulting in Northern Hemisphere power station experience dominating in market countries. 3. Failure of governments to draw on privately practising Australian power engineers and coal technologists in technical workshops, presentations and assistance to overseas countries, to ensure that personnel whose business it was to serve the follow-on needs of countries were readily available. The result of these failures has been that: 1. Only a fraction of prospective overseas coal-fired power projects have proceeded. 2. Australia has had no influence in the design of overseas power stations to ensure that potential customers would be confident that Australian coals could be reliably burnt in their boilers.

Jan 1, 1987

By Orid A

A fast, non-contact technique for measuring sizes of rock fragments on a conveyor belt is presented. An image processing technique called active stereopsis is used which makes use of a light stripe projected on to the surface of the fragments on the conveyor belt. A CCD TV camera is used to capture the shape of the distorted light stripe. the video image of this shape is then processed by a computer program so that the 3D profile of the surface can be obtained by triangulation. The sizes of the rock fragments are then calculated from this profile. The speed of the technique is improved by calibrating the light stripe system before measurement begins so that the profile of the fragment surface can then be measured using simple geometry. The technique is fast and highly parallel so that it is able to operate in real time.

Jan 1, 1990

Gravity concentration of tin at Renison Limited uses tables and spirals to treat the various coarser fractions produced from sulphide flotation tailing. An acceptable final tailing cannot be made from one pass over the tables and spirals and therefore the tailing from these separators is reground and combined with the sulphide flotation tailing as the feed to the classification section. The gravity section became increasingly overloaded in the years preceding 1976 due to efforts to maximize tin recovery to the gravity concentrate. In April, 1976, two 2DSV Reichert cone concentrators in series were installed to treat the table and spiral tail- ing stream, prior to regrind, to scavenge a small tonnage of hard, coarse low tin grade material for rejection to final tailing. Gravity section loadings were decreased markedly, allowing operator attention to be directed more to table performance than to spillage collection. An increase in mill throughput of approximately 15% was possible following the commissioning of the Reichert cones. The cones are currently operated to make the minimum tonnage of tailing consistent with reasonable- gravity section loadings.

Jan 1, 1978

By Wilson PH

A research programme sponsored through the Australian Mineral Industries Research Association investigated two aspects of mine aerodynamics on model scale. These were aero- dynamic losses in (a) shaft/airway intersections and (b) losses created by mine cages moving in a combined haulage/ventilation shaft. The shaft/airway intersections studied included base and intermediate levels for both upcast and downcast. shafts, with one to four rectangular airways intersecting a circular shaft. Changes in intersection geometry were limited to the installation of 45¦ conical brow cutoffs of varying size and the addition of simple flow control devices. The relative air- flows between the airways and the downstream shaft were varied over a range employed in Australian mining practice. In general, experiments revealed that a small brow cutoff was significantly better than none at all, and a simple device such as a cone can reduce losses and improve flow stability at an intersection. The mine cage studies determined the effect on aerodynamic loss of cage area blockage, height/length ratio, openings in cage walls and surface roughness due to external structural members. The results show that in a combined haul- age/ventilation shaft, when the relative air

Jan 1, 1978

During the last 20 years, manufacturers of Australian iron have given increasing attention to development of external markets for processed blast furnace slag. Slag has been in widespread use overseas and data on the performance of Australian slag in concrete lave shown it is suitable for that use. Chemical and physical properties of typical Australian slag products including air cooled, granulated and pelletised slag are discussed and compared with local natural aggregates. Special attention is given to pumping achieve- ments with slag concretes and the observed durability of concrete after many years service. More'recent applications for granulated slag as a sand replacement are discussed. It is concluded that'whilst more wide- spread use of slag is possible, the cost of marketing and transporting slag are likely to restrict opportunities unless for local usage.

Jan 1, 1979

By A Logan, B Cuthbert

Brown and Chitombo (2007) indicated that during the last two decades, the international mining industry has been using mainly mass mining methods to extract safely and economically some of the important commodities such as copper, diamonds, gold, iron and nickel. Mass mining may be implemented either on the surface through large open pits or underground using mining methods such as sublevel, block and panel caving. Developments in the last ten years have demonstrated that caving methods can be applied successfully in strong orebodies at greater depths and in increasingly challenging geotechnical environments for which more traditional mining methods would be unsuitable, unsafe and/or uneconomic. These underground mass mining challenges require æfront endÆ investigation and analysis, robust engineering design and disciplined implementation and operation. Newcrest Mining Limited has focused its efforts on the development of gold/copper projects of substantial scale and margin. To help achieve this, the company is applying and further developing mass mining methods. These include large-scale open pits (OP) and underground mining methods such as sublevel (SLC), block (BC) and panel caving (PC). Block and panel caving now offer economies of scale opportunities for Newcrest to achieve high production rates at lower production costs; thus enabling the exploitation of mineral endowments at higher margins. This paper discusses the practical aspects of caving technologies that Newcrest continues to develop through its expertise at Telfer and Ridgeway SLC operations, Ridgeway Deeps BC and Cadia East PC projects.

Jan 1, 2008

By Wingham DW

Based upon the previous work of Norman and Loeb, a method, was used, to assess-the comparative wearing properties of ten different alloys being used, or being considered for use, as mill liners and grinding media at Mount Isa. The materials to be tested were obtained in the form of large diameter balls and were run, along with the regular ball charge, in a large ball mill operating-under normal grinding conditions. At selected. intervals, the test balls were removed from the mill, weighed and identified, and their relative wear rates determined.

Jan 1, 1963

By Waters CA, Happ JV

The debismuthising plant, commissioned in 1980, is based on the Kroll-Betterton process for preliminary bismuth removal with subsequent antimony treatment for fine debismuthising. Bullion flowrate is continuous and the plant was designed to achieve low bismuth lead product at rates of up to 20 tonne/h.Development of the first stage of the operation has enabled reliable operations at 25 tonne/h to be achieved. Thesedevelopments also introduced the opportunity to treat higher bismuth bullion at up to 35 tonne/h when operating the first stage only to produce product lead of 0.029 per cent Bi, meeting the ASTM B29-55 Corroding Lead Standard.

Jan 1, 1985

By Adshead ND, Blake KL, Rotherham JF, Rotherham M, De Jong G

Magnetite deposits with distinctive ¦ actinolite ¦ apatite -bearing gangue and spatially-extensive sodic-calcic wall rock alteration occur in both Proterozoic metamorphic terrains and Mesozoic-Tertiary magmatic arcs. Examples from both settings constitute significant sources of iron ore (e.g. Kiruna, Sweden; El Romeral, Chile) and some host major Cu-Au deposits that have a local association with K-silicate alteration (e.g. Cloncurry district, NW Queensland; Copiapo district, Chile). A growing body of evidence points to a hydrothermal origin for these systems involving high temperature, low S oxidized fluids. The Cloncurry magnetite-Cu-Au deposits are products of the local structurally channelized influx of a specialized high salinity ore fluid into larger-scale alteration systems developed during pluton emplacement at greater depths than those associated with subvolcanic (porphyry) Cu-Au deposits. The geological characteristics of deposits in magmatic arcs are consistent with a similar mode of origin albeit in rather different tectonic settings.

Jan 1, 1995

By Thompson D, Burgess G. C

Subsequent to large scale trials in 1987, the installation of a submerged lance Sirosmelt furnace system was approved in late-1988 for the cupellation of retort bullion to dore silver. Commissioning work commenced in June 1990. During the process air is lanced into a molten slag bath contained in a cylindrical vessel to rapidly oxidise the granulated feed bullion from 15 - 25 per cent silver to rough dore grade. The process is now an integral part of the Precious Metals operation replacing the first stage reverberatory cupellation furnaces to achieve productivity improvements, lower silver inventory and increased silver Recovery.

Jan 1, 1992

By Doyle J

The direct method of gas content determin ation developed by McCulloch and Diamond of the U.S.B.M. has been adapted to estimate the gas content of coal seams from slim exploration borecores in the Southern Coalfield. Emphasis has been placed on the measurement of this parameter without the physical destruction of the core which is required for subsequent chemical analysis. In field and laboratory equipment is simple and inexpensive. It enables the determination of lost and desorbed gas from a fresh geological core. Residual gas is not measured but is considered to be relatively low and of no consequence in ventilation considerations. Results to date show good correlation with those obtained from underground face samples. Gas contents from the mined seams varying from 2 m3/tonne to 14 m3/tonne have been measur- ed with this apparatus. Gas desorption characteristics of South Coast coals have been found to closely follow exponential mathematical Models.

Jan 1, 1983

By Burnett C. C H

GEMNet, (Grade Estimation using Mapping Networks), is a grade/reserve estimation software system that uses the artificial intelligence technique known as neural networks to perform reserve estimates from both two- and three-dimensional data samples from a mineral deposit. The system is the result of research carried out over the past three years into the feasibility of using neural networks for reserve estimation at the AIMS Research Unit in the Department of Mineral Resources Engineering at the University of Nottingham. This paper describes the architecture of the GEMNet system including details of the neural network components of the system. The performance of the GEMNet system is then compared to several other widely used reserve estimation techniques on two reserve estimation examples. The results produced by the GEMNet system compare favourably with more conventional estimation techniques, but require fewer assumptions to be made about the form of the data used, and do not require the use of complex mathematical modelling.

Jan 1, 1995

The main objectives of this paper are to identify the main sources of coal dust and to investigate measures for minimisation of dust generated at these sources at the Bukit Asam open cut mine, on the island of Sumatera, Indonesia which uses a

Jan 1, 1994

By M Miller

Operators of nickel laterite pressure acid leach and gold pressure oxidation technology frequently employ a series of steam condensing heaters to preheat the leach feed slurry. The heaters are an economic pinch point û although the thermal performance of the heaters is critical to overall process viability and operating cost minimisation, they are also a significant capital item and must be sized accordingly. Despite this, discussions of the factors underlying heater design are conspicuously absent from technical literature, and existing operations feature a conflicting range of heater sizes and configurations. This variety would suggest that at least some of the chosen heater designs are oversized. As part of its detailed design stage, the Ravensthorpe Nickel Project (RNP) constructed and tested a pilot plant heater to develop an understanding of the heating process and to ensure that the RNP heaters were appropriately sized. This testwork used RNP slurry at design density and viscosity on a 450 mm diameter, 6500 mm high column. The pilot plant testwork demonstrated the intrinsic efficiency of the direct steam condensation heating process, which was essentially independent of slurry density and viscosity. Presence of non-condensable gases in the steam phase decreased the heat transferred in certain circumstances, but heater performance remained consistent with thermodynamic limitations. Stagewise heat transfer within the column was rapid, and suggested either a very high slurry surface area or excellent heat transfer within the slurry phase. While the testwork did not set out to distinguish between these effects, physical evidence pointed to droplet formation in the inter-tray shower zone, giving a high heat transfer area. For scale-up purposes, the key facts were that the heat transfer rate was not limited by using high viscosity slurries and heaters could be designed using the principles applied to the smaller of those in existing operations. This paper discusses existing slurry heater designs, the current understanding from open literature, the pilot plant testwork, results and analysis, and scale-up to commercial sized equipment.

Jan 1, 2005