Search Documents

By C E. Gawith

The Waihi underground mining operation currently mines epithermal veins ranging from two metres up to ten metres in width using a ‘Modified Avoca’ stoping method. This method consists of longhole bench stope mining at 15m to 18m sublevel spacing. The bulk of production drilling and blasting is top down with the extraction length of a typical stope panel nominally being 18m to 20m along strike. A stope panel is usually taken in two blasting cycles followed by the remote bogging of the stope ore. The panel is backfilled in-cycle using unconsolidated waste rock material which is tipped into the void from the upper level using a Caterpillar R2900 or R1700 sized underground loader. The underground mine first commenced production in 2008 and up until 2016, as was typical of many open stope mining operations at the time, an underground loader was used to place a waste rock bund at the top brow of the open stope. This rock bund was the principal means of protecting people and equipment from this hazard. In 2016 there was a fatality at the mine when a loader that had been tasked with building this rock bund fell into the stope void. Immediately post incident all mining and processing operations were suspended for a week to allow colleagues to grieve, to observe cultural protocols and to begin the investigation into this event. During this period senior operators, supervisory and technical staff developed an innovative system which used steel bollards to protect this open edge. With development over the following months this bollard system has eliminated this hazard from the Waihi underground mine.

Mar 15, 2021

By G Campbell-Cowan

Much has been written about the fact that most transformation efforts disappoint. This paper addresses factors that should be taken into consideration in planning and implementing transformation programs to ensure success.In 2009, St Barbara commenced a transformation program to address issues of chronic poor quarterly operational performance; financial pressure caused by the unreliable operational performance; and an inability to develop business plans with integrity and to reliably deliver on the plans. As a result of a number of years of disappointing operational performance, St BarbaraÆs culture was not conducive to business success.This paper uses lessons learnt during St BarbaraÆs transformation program to highlight key characteristics of change programs that can generate significant sustainable benefits. While there were many benefits from the transformation program, the most significant impacts of St BarbaraÆs program have been transformation of the companyÆs culture and capability of people as business leaders; the establishment of a business systems framework to guide the design and development of systems; and developing support functions, for example centralised procurement and supply chain, business improvement and technical services.CITATION:Campbell-Cowan, G, 2012. Business transformation - Lessons learnt for successful change, in Proceedings International Mine Management 2012, pp 135-142 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 20, 2012

By R S. Sing, M D. Yadav, G Udaybhanu

This paper presents the results of the first part of a research project to study the effect of various inhibitors to reduce the spontaneous heating susceptibility of some highly susceptible Indian coal seams. In this investigation 11 inhibitors were chosen and applied at three, five and ten per cent of their concentrations in an aqueous solution for four coal samples collected from four different seams. The susceptibility of coal samples, before and after application of these inhibitors, was determined by carrying out crossing point temperature (CPT) analysis. The findings of this study have indicated that it is possible to retard the tendency of spontaneous heating of Indian coals to a considerable extent by the application of six of the inhibitors studied. Further, these inhibitors were tested in 1:1 combination to study their synergistic effect. Finally the economics of the application of these inhibitors has been analysed and four inhibitors are recommended for field use. These results have direct application to control fire and improve productivity and safety in coal mines.

Jan 1, 2005

Energy is central to respond to critical stakes on human and industrial development requirements as well as on climate change. The increase of the share of carbon-free energy sources in the global supply mix will help to reduce significantly greenhouse gas emissions (GHG) as power generation accounts currently for 41 per cent of these emissions from the energy sector. In this energetic mix, nuclear and renewable energies are complementary, the first more focused in the baseload power generation whilst the second is well suited for decentralised power generation. In this context, AREVA's goal is to enable everyone to have access to a cleaner, safer and more economical energy. Regarding nuclear energy, AREVA's strategy is to capitalise on its integrated operation model, which groups together fuel cycle and nuclear power plant construction, aiming at building one third of the new nuclear capacities and securing the fuel cycle supply chain for its existing and future customers. Therefore, the front end of the uranium fuel cycle, from mining to the fabrication of fuel assemblies, has a key role in the sustainability of the nuclear industry. The replacement of the current capacity and the entrance of new countries on the nuclear power generation might lead to a significant rise of uranium demand by 2020. In order to be prepared in time, AREVA defined an ambitious industrial program to expand mineral reserves, increase the production of uranium concentrates, replace the conversion capacity, build two new uranium enrichment plants, one in France and one in the United States and upgrade its fuel manufacturing plants. To support the front-end industrial activities in the short and long term, AREVA invests on a portfolio of R&D projects to find out solutions to meet customers' needs, to improve its competitiveness and to develop new concepts and solutions to anticipate future market evolutions. In particular, some important technological challenges in mining must be surmounted to develop cost-effective methods to explore and exploit low grade deposits while creating sustainable solutions for reducing reagent, water and energy consumptions. In this lecture, an overview of the industrial investments of AREVA in the front end of the uranium fuel cycle and some highlights on its R&D major axis will be presented. This is an abstract only. No full paper was prepared for this abstract.  

Sep 13, 2010

By J Stiefenhofer

"*This is an abstract only*Construction of geological models for kimberlites has historically largely been based on visual volcanic textures and features, with chemical data only collected on an ad-hoc basis depending on the level of perceived complexity observed in the geological data. The focus of this paper is a high-level view of the impact an initial absence (or lack) of relevant chemical data had on two kimberlite resource models as well as how the magnitude of the problem increased once the resource estimation process commenced (Stiefenhofer, 2013). The impact of ignoring chemical data on a project assessment where micro-diamond estimation techniques are employed, is also discussed. Resource estimates based on micro-diamond data are critically dependent on the use of the correct geological model since stationarity of the size frequency distribution is key to the generation of correct grade estimates. A multilevel approach is advocated where the volcanological/visual model is verified using chemical data and both are in turn verified by the diamond data.CITATION:Stiefenhofer, J, 2013. The use of chemical and metallurgical parameters to enhance the economic value of kimberlite resource models, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013, pp 101-104 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 29, 2013

By M Noakes

EcoTechnology refers to a series of potential metallurgical processes for complex ores, concentrates, tailings and slags that are all based on an initial chlorination step at low to moderate temperatures probably in a fluid bed chlorinator (FBC). Examples of the research and development (R&D) results are provided in this paper for a high grade Au/Sb Leach Tailings (EcoGold<sub>®</sub> Process), a very refractory sulphide Au concentrate, a refractory gold calcine tailings, a Cu/Au tailings (EcoCopper<sub>®</sub> Process), bulk polymetallic sulphide concentrates and polymetallic sulphide/oxide complex ores (EcoZinc<sub>®</sub> Process and EcoLead<sub>®</sub> Process). R&D on over thirty different ore types has been conducted at a bench scale as discussed. Latterly a dedicated pilot plant was designed and constructed by EcoTech Mining Pty Ltd (EML) and several of the different feed stock results have been confirmed by pilot plant testing. It is planned to scale up to a commercial demonstration plant. To demonstrate the versatility of EcoTechnology, bench and pilot plant test results on five of the projects are used as case studies as follows: Fosterville ‘leach tailing’, VIC; Wiluna flotation concentrate – BIOX Feed, WA; Wiluna calcine facility tailings, WA; Mt Morgan Cu/Au tailings, QLD; Polymetallic sulphide concentrates from Pegmont Deposit, QLD and Polymetallic sulphide/oxide ores from Commonwealth Mine Project, NSW. CITATION: Noakes, M, 2018. Improved recoveries and environmental outcomes from complex ores utilising EcoTechnology, in Proceedings Complex Orebodies Conference 2018, pp 122–123 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

In May 2000, Kanowna Belle Gold Mines (KBGM) carried out a detailed Truck versus Shaft Haulage Study. The study showed that whilst the shaft option had many operating cost benefits the capital costs were too high, therefore the truck option was selected. In May 2001, the concept of achieving æshaft typeÆ benefits without the capital costs was floated. This is achieved by separating the hoisting of ore from other mining activities. The general concept is that material from underground is transported to a central location and then transported to the surface by a special truck fleet, thus removing the dependency between trucks and loaders, providing the mine with surge capacity and decreasing operating costs. At KBGM these advantages have been gained by installing an ore pass system with a plate feeder at its base that directly loads trucks. This provides the mine with a haulage system with enough surge capacity to remove the interdependency between trucks and loaders. The plate feeder is situated just off the decline which creates the opportunity to use larger more reliable, lower cost trucks. A number of truck types were considered for the truck loop including Elphinstone AD55Æs which are the truck type being used on site prior to the truck loop, CAT 775EÆs and power trailer road trains. This paper covers the philosophy behind the truck loop, the truck selection process, project installation and commissioning, people issues and the benefits expected by the operation. As of May 2002, the project is nearing completion, with decline haulage expected to commence in July 2002.

Jan 1, 2002

Last September, when I was asked to prepare this paper, I was told the subject was "mining," a broad subject indeed! Rather than choose one of the many important technical and economic details which characterize mining today, I turned to a subject which fas- cinates me: mining's image. If we are to survive and prosper into the twenty-first century, and if industry and society are to continue enjoying the material benefits which flow from mining, we must address the melancholy fact that the general public at best does not understand mining, and at worst does not believe it is needed or deserves to continue. While my point of view is largely that of an American mining executive, I would hasten to point out that Homestake has participated in Australian mining for over three decades, and our subsidiary, Homestake Gold of Australia Limited, is now a major producer in this "lucky country." Does society need a viable minerals and metals industry? The answer is obviously "yes," so the challenge is to change some minds: not just those of the amorphous "public," but on a focussed basis targeting journalists, educators, TV commentators, politicians and opinion makers of all stripes (I thought of using "rifle shot" instead of focussed but thought that might be misconstrued). Along the way we miners must also look deeply into ourselves, our attitudes towards the society in which we function, and our willing- ness to change as well as to seek change in others. How did we become such bad guys? More than a century ago mining was not just accepted, it was even romanticised. In America, we had altered the time-honored concept of "Crown" lands into public lands made easily available to settlers pushing back the frontier. Miners even preceded the farmers and stockmen in what was perceived as nation-building, although by the 1890s there was a growing interest in conservation, especially the protection and management of forests and national parks. Even though emphasis was shifting toward government stewardship and away from trans- fer of public lands to private ownership, homesteading and mining were clearly recognised as valid uses requiring not just access, but security of tenure. Indeed, conservation as it was then understood implied management of the public domain as well as its protection. Initially this was no great problem to the U.S. mining industry, but as the nation grew and competing land uses became more important, conflicts began to appear, first over water rights and later over air quality and destructive mining practices. But these were local disputes rather than national issues, and two World Wars, the Great Depression and post-war reconstruction lulled our industry into thinking that nothing had really changed. After the storm began to break in the 1960s, the mining industry found itself confronted by a growing maze of complex and costly laws and regulations. It took us longer than it should have to realise that, in facing this challenge, we seemed to have lost the understanding and support of many of our legislators and a majority of the general public. For over 20 years now, since the first Earth Day in 1970, the U.S. Mining

Jan 1, 1991

By H Ramandi, H Masoumi, I Canbulat, B Hebblewhite, J Oh, S Saydam, W Timms, S Mo

This paper reviews the floor heave mechanisms in underground coal mine roadways. Previous studies have reported three main failure mechanisms: bearing capacity failure, buckling and swelling. The buckling failure has been observed where immediate floor strata are relatively strong and thinly bedded. On the contrary, the weak floor strata have been associated with both the bearing capacity failure and swelling mechanisms. The bearing capacity floor failures are likely to induce other types of instability such as pillar punching, tensile failure of pillar, roof fall and subsidence as well as floor heave. Despite a considerable amount of research, predicting the magnitude, location and timing of floor deformation is challenging with current state of knowledge. CITATION:Mo, S, Ramandi, H, Oh, J, Masoumi, H, Timms, W, Canbulat, I, Hebblewhite, B and Saydam, S, 2018. A review of floor heave mechanisms in underground coal mine roadways, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 196–206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

Sheaves are a critical safety component in a winding system and are expected to survive such extreme loading events as rope break. Sheave designs have often been developed and evolved empirically, consequently many existing sheaves are not necessarily subjected to the detailed analyses that are possible using todayÆs design tools. The design philosophy for sheaves is that the rope should be the weakest link in the system so that associated equipment can function safely for any load up to rope break. A number of failure mechanisms must be considered, but buckling is often prominent. During the course of investigating the feasibility of upgrading the hoisting capacity of a winding system, the capacity of all critical components was reviewed. The sheaves in the system were found to have insufficient spoke buckling capacity for the specified rope. A proposal to increase the spoke buckling capacity by connecting spokes together using a simple tie arrangement was evaluated and found ineffective. An alternative tie arrangement concept was developed and evaluated and shown to be adequate. This paper describes the finite element model, analysis approach and results for the original sheave and the two modifications. The contribution of the sheave rim to the total buckling capacity is evaluated. Some practical issues for spoke tie modifications are discussed.

Jan 1, 2005

THE South Mine. owned by the Broken Hill South Limited, occupies mineral leases 7 and 8 on the Broken Hill lode. The ore reserves are 4,250,000 tons, and the ore hauled for the year ended June, 1930, was 387,000 tons, the total to date being 7,840,000.The mine, down to the 1070-ft. level, is naturally divided into two sections, the northern and southern ends. Ore extraction is practically completed in the northern end to this horizon, while the southern end is developed ready for a concentrated attack.Fig. 1 shows the state of the 8215-ft. level, after connection to the new shaft.The levels above and below to the 1070-ft. level are in a similar condition, while below the 1070-ft. level the stoping has been confined to the north end, but not completed. The south end on these levels is also partially developed.The ore at present is hauled up No. 1 shaft, which is centrally situated to the present workings. This shaft was put into use in 1909, and in 20 years has had approximately 5,000,000 tons of ore pulled through it.The company, having proved the existence of large ore-bodies in the southern end of the mine, decided to sink No. 7 shaft. This is a six-compartment frame-set shaft (see Fig. 2) equipped with two cages and two 5-ton skips, the remaining compartments being utilised for electric cables, pipes, and ladders. The surface arrangements will include a steel head frame, electric winders, and breaker station.

Jan 1, 1930

By L Neems

In conjunction with Orica Explosives, Worsley Alumina have managed a program of continuous improvement to their cap rock blasting over the last two years. Blasting conditions are challenging because of the hard and shallow nature of the material. Blasting costs must be controlled and the environmental consideration of noise and dust is critical. Worsley have sought to determine the optimum balance between drilling and blasting costs and fragmentation. As the cap rock has few inherent weaknesses, loader productivity is strongly controlled by the degree of fragmentation from blasting. The optimum blasting solution is also constrained by maintaining airblast levels at the surrounding residences below 115 dBL . The major blast design parameters optimised during the program were stemming type, stemming length, powder factor and blasthole diameter. A series of carefully managed trial blasts were fired during 1997 and 1998 to quantify the effect of these parameters. Fragmentation was digitally measured using OricaÆs Powerseive G technique. Shovel productivity, airblast levels and blasting costs were also quantified. As a result of the project, Worsley now have an increased knowledge of the key parameters driving blast performance, and their consequent impact on downstream processes, the environment and total mining cost.

Jan 1, 1999

By A J. Clough

There has been an unprecedented rise in the fatality rate in the Australian mining industry over the last few years. The factors behind this rise are not clear; however, it is noted that the increase in fatalities has occurred during a fall in commodity prices.This paper examines prevention methods and systems to deal with hazards that have the potential to result in either single or multiple fatalities. Managing the risks associated with mine ventilation is used to illustrate the principals behind the approach.The paper also touches on the broad science of human error and proposes a multifaceted approach to controlling and preventing fatal risks.A summary of the steps involved in developing an effective principal hazard management plan is provided.CITATION:Clough, A J, 2015. Ensuring an effective principal hazard management plan, in Proceedings The Australian Mine Ventilation Conference, pp 3–8 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By A Stradling

For a geometallurgical program to be successful, linkage must be made between the geologists and geostaticians who understand and model the orebody, the metallurgists who determine the value that can be extracted from the different geometallurgical units, and the mine planners who develop and optimise the plan to extract maximum economic value from the resource. One of the primary purposes of geometallurgical models is in the determination of the economic cut-off between ore and waste. Recognition of the level of confidence required in the estimation of grade, throughput and recovery is critical to the planning of a successful geometallurgical program. It also helps clarify the scope of work needed to mitigate risk at each stage in the development of a new mine projectThis presentation provides some of the author’s experience with development and application of geometallurgical models for existing base metal operations. It discusses how geological units defined by lithology, structure, alteration etc, can be translated into geometallurgical ore types defined by mineralogy, ore hardness, and flotation behaviour. Examples of how these characteristics have been used to estimate key economic parameters such as mill throughput and flotation recovery at two brown-field operations are provided. The first example relates to the modelling of metallurgical performance at Teck’s Red Dog zinc-lead mine in Alaska. Prior to 2000, zinc, lead and silver recoveries from a block of ore at Red Dog were either assumed constant, or were varied according to simplistic models. Throughput was not thought to vary substantially between blocks, so an average value was used for each blended stockpile. It is quite possible that some ore-value blocks were classified as waste, and some waste-value blocks treated as ore, as a result of poor understanding of the true economic cut off across the wide range of ore types observed at Red Dog. After an extensive flotation test program, the first assay-based zinc recovery model was developed for the Main pit reserve in 2003.**This is an abstract only. No paper was prepared for this abstract**

Sep 5, 2011

By G B. French

Post a serious heating event underground, and at the direction of the State Mining Safety Authority, a mining company needed to demonstrate the use of cutting-edge technology to mitigate future events. Yokogawa were contracted to provide a turnkey solution to help the mine achieve this objective. The solution was to use a fibre optic-based Heat Detector that will allow entry into and around the mine considering the potential volatility of the environment, also the need to redeploy as mining activities moved underground and more boreholes are added. Industrial strength fibre optic cable and a robust connector system was chosen to achieve this goal and give the customer the ability to send cable down boreholes of up to +1 km and continuously monitor the temperature ofunderground roadways. Being able to re-deploy the cables into different boreholes and link borehole temperature measurements gave insight into all areas on the mine. The machines deployed on-site were the Yokogawa DTSX1 heat detector incorporating the Ramen Backscatter principle. Being of a robust construction and a low power consumption device, it was easily included into the portable monitoring trailers designed by the customer and built locally.

Oct 12, 2022

By Moy A. D

The Esperanza deposit is located 120 kin N of Mount Isa, Queensland at approximately lat 19¦20'S, long 139¦22'E on the Camooweal (SE 54-13) 1:250 000 scale map sheet. It is one of several structurally controlled copper ¦ cobalt deposits developed along the Mount Gordon Fault zone and related faults, within the Western Fold Belt of the Mount Isa Inlier (Figure 1). Together with the nearby Mammoth orebodies it forms the basis of the Gunpowder operation of Aberfoyle Limited. Until recently ore was mined from the Mammoth orebodies by open stoping with decline haulage to surface leach pads. Leaching of in situ broken ore (in place) and surface heaps, followed by solvent extraction and electro-winning (SX-EW), produced copper metal on-site. In March 1997, mining was suspended at Mammoth and the focus of the Gunpowder operation switched to development of the Esperanza orebody, which is expected to begin open cut production in mid 1998. SX-EW methods will produce 44 000 tpa of copper from an expanded plant. The pre-mining mineral resource at Esperanza (measured, indicated and inferred) is estimated at 4.6 Mt averaging 7.7 per cent copper.

Jan 1, 1997

By Espig D, Standish N

In the paper a stochastic model of the batch sieving procedure is presen- ted resulting in a system of ordinary differential equations to describe the time dependence of the mass fractions on the sieve surfaces being randomly influenced by sampling errors. The coefficients of the system can be interpreted as sieving velocities. Their dependence on the sieving con- ditions is discussed and a special type of functional relationship and methods are suggested to determine this function experimentally. Moreover the applicability of the approach is demonstrated by an example to evaluate the particle size distribution, if only the result of incomplete test sieving is known. For this problem a rough error estimation is performed.

Jan 1, 1984

Sishen uses a state-of-the-art tracking system to track material from its position in blast blocks through various stockpiles and crushers. Qualities are blended directly to the crusher as opposed to blending from stockpiles. This poses an interesting challenge to the planning department to simulate these conditions. The software used in these simulations are Whittle 4X and Maximiser for long-term planning, Xpac for medium-term planning and Mine Works Planner for short-term planning. Geological models and mine design layouts utilise Surpac. Sishen introduced Xpac a number of years ago; the system has developed and changed over the years. With the Sishen Expansion Project (SEP), which aims to utilise low-grade material, major changes to the planning process have to occur. SEP requires that the mine have two different plants, which utilise two different ROM feeds and have different beneficiation curves. Xpac is used to produce a rolling 18-month plan, which is as close to actual operations as possible. In order to do this, the simulations have to take into account the plants beneficiation curves, stockpile movements, hauling distance and equipment needs. On top of this, the schedule has to continually consider specifications for Fe and the contaminants. Plant yields also have to be kept within a certain bandwidth. Xpac is used to simulate the above parameters, as well as generate the raw data required to produce a mine budget. The paper will also show how the 18-month planning process and subsequent planning processes are measured and aligned. Xpac has proved to be an excellent tool to achieve these goals.

Jan 1, 2005

Flat jack stress determinations in selected colliery roadways have revealed a range of measured stress from 330-p.s.i. tension to 3,750 p.s.i. compression. Photoelastic examination of loaded plastic and actual rock mo.odel mine openings has shown that the primary horizontal stress required to attain these measured stresses would be from one to three times the superincumbent vertical load.Examination of roof movement with a. borehole oxtensumeter and a series of anchors at various horizons to 30 feet in a. vertical roof borehole showed that when a standing face waa.s advanced the roofmovement was practically confined to the lower two feet. The ma.j ority of this movement occurred during the 36 hours after mining at this face commenced.The use of a. radioactive isotope and a. scintillation counter in a. pair of parallel bcreholes promises to be sensitive and accurate method of roof bedding plane crack detection.

Jan 1, 1963

Dr. Willett. I will start by answering one or two general points which have been posed. The first point is a question of liability of a seam to spontaneous combustion. Some seams are very liable to spontaneous combustion. Some seams are not liable at all except in most abnormal circumstances, and some seams have a liability somewhere between these two extremes. Dr. J. S. Haldane made the comment some 50 years or so ago that if you try hard enough you can make any coal seam in the world fire spontaneously. Many heatings have in fact occurred because the coal has been allowed to be ground up into a fine state and there has been air leakage through it for many years. This has resulted in spontaneous combustion which would not have occurred in some seams unless conditions had been very abnormal indeed. One comment I heard while listening to the discussions of one team was the importance of encouraging morale and the team seemed to go to the extent of suggesting that this was more important than the actual technical action taken. Though I agree that everything possible should be done to encourage morale, it must be in conjunction with the correct technical method of dealing with the Emergency.

Jan 1, 1973