Search Documents

By G Davison, C Rossimel, M Bouazza

Expanding rock bolts anchor within a rock mass more efficiently than non-expanding varieties. This is of great importance in weak ground conditions, where grouted friction bolts perform less efficiently than in good ground conditions. Filling a Split Set with demolition concrete has been shown to double the load-carrying capacity when compared to conventional use of Split Sets. This report details verification of these results by installing and pull-testing 14 Split Sets of varying grout conditions within in a fault zone. These Expanding Split Sets achieved loads double and triple that of ungrouted and normally grouted conventional Split Sets. A literature review and chemical analysis were conducted to understand the expansion process better. It was found that 20 per cent more calcium is included in expanding cement, which is responsible for its growth. Factors most affecting the expansion process were identified. Furthermore, the expansion rate of a bolt outside a borehole was measured and 6 mm of expansion across its diameter was found. The compressive properties of the cement were compared with other types, due to expanding cement becoming uncohesive after the expansion process is complete. When confined within a Split Set, compression testing demonstrated that this grout is just as strong and rigid as normal grout. Finally, the bolts were tested by shear and it was found that the Expanding Split Set (ESS) has a similar shear capacity to grouted Split Sets, which is 70 per cent higher than that of ungrouted Split Sets. These results enabled the mechanism for improved performance in weak ground conditions to be verified. Expanding grout will expand the Split Set into its borehole of varying diameter and lock it into place, creating increased friction and resistance to pull-out. This paper shows that ESSs can be a useful reinforcement technique in weak ground conditions.CITATION:Rossimel, C, Davison, G and Bouazza, M, 2014. An investigation of expanding split sets in weak ground, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 159–170 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

Myuna Colliery long term ventilation requirements were included as part of the overall planning of colliery construction and underground development. Ventilation, during the simultaneous sinking of two drifts and the downcast shaft, was accomplished by established methods of ducted exhaust and blower fans. Drivages for the 3 seam interconnections of shaft and drifts were ventilated by extension and duplication of the exhaust systems. Ventilation, for the below seam extension of the belt drift, construction of between seam and below seam bins, and the completion of a circular between seam drift, required a step by step changeover to a temporary main ventilation exhaust fan mounted adjacent to the top of the completed downcast shaft. The second, permanent upcast, shaft was commenced and colliery production started one seam at a time, using the transport drift, while the underground bins, belt and between seam drifts were completed. The uocast shaft was completed and a connection made in the upper seam, completing all contract mining and allowing the main fan to be erected. The permenent twin centrifugal fan system was installed, commissioned and test run to

Jan 1, 1983

By Quast K

A series of laboratory flotation tests were conducted to evaluate the effectiveness of various depressants as arsenic (and zinc) depressants in the lead cleaner stage of the NBHC mill at Broken Hill. The depressants used included potassium cyanide, ferrous sulphate, sodium hypochlorite, potassium ferricyanide and two Cyanamid commerical depressants, Aerodepressants 610 and 633. A standard roughing stage was completed before the addition of the reagents in the cleaning stage. All reagents tested produced significant arsenic depression, with the best results being obtained with the addition of potassium cyanide and sodium hypochlorite. Some of the depressants activated the zinc in the process of arsenic depression. The best result was obtained with the addition of 90 g/t potassium cyanide at a pH of 10 when arsenic recovery was only 1/4 that of the value obtained for the standard test.

Jan 1, 1991

By R Yang

This paper presents a fragmentation model for large production blasts in an open pit or underground environment. The paper shows that the particle velocity is directly related to pressure, strain, and strain rate and so it can be considered as driving force and mechanism of rock fragmentation. This is supported by the fact that a vibration with a larger peak particle velocity (PPV) generates larger disturbance in rock and so finer fragmentation or more blast damage than a low PPV. The crack distribution in rock from impact is based on findings from previous researchers (Seaman, Curran and Shockey, 1976; Liu and Xu, in press). The fragmentation size is calculated at three-dimensional grid points within a blast. The fines and oversized blocks are calculated explicitly – the fines generated close to blastholes and big blocks far from boreholes are modelled naturally. The multiple blasthole fragmentation (MBF) model takes surveyed irregular geometry of the free face of a blast as the calculation boundary. The MBF can model fragmentation with over one million grid points. Examples of the model’s field comparison are also included.The PPV at a calculation grid is estimated based on the same approach used for the near field non-linear vibration model (Yang and Scovira, 2007). The method is based on the dominant charge for a calculation grid point, non-linear charge weight superposition within a charge and from multiple charges, strain wave broadening, and amplitude attenuation with distance from a charge segment. The blasthole confinement affected by earlier firing charges is also taken into account.The MBF model inputs from blast design, such as: location and orientation of each blasthole, stemming length, blasthole diameter, multiple decking, bench height, initiation sequence, etc. It models the effect of the delay and its scatter in each blasthole on fragmentation and has a statistical modelling capability for geological random variation on attenuation of particle velocity wave. The wave reinforcement due to instantaneous waves arriving or diminishing cooperative contribution due to long delay intervals between charges is also simulated.The results are displayed in 3D volumetric plots, contour of fragmentation in cross-sections, and size passing curves for a whole blast or a region of the blast.CITATION:Yang, R, 2015. A multiple blasthole fragmentation model – its concept, formulation, capability and field comparison examples, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 177–186 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

Two characteristics of the modern mining industry are that there is a skill shortage and that young professional people rise rapidly into highly responsible supervisory positions. With this responsibility comes the burden of identifying and managing health and safety risks. Without the benefit of a comprehensive health and safety training program, these young professionals may be putting both themselves and those under their supervision at risk. The Moura Mine explosions and the asbestos health disaster should not be just artifacts of history, but highly valued lessons that impress the need for comprehensive health and safety risk management strategies on young professionals. From the perspective of the former secretary of the Committee to implement the findings of the Moura (Disaster) Inquiry and as the former coordinator of the Coal Workers Health Scheme, key issues in occupational health and safety management systems are explored.

Jan 1, 2005

By B Green

With a focus on safe productive tonnes, there has been an ongoing drive to increase the productivity of the mining fleet across BHP Billiton. In response, a team from the Iron Ore business was formed to review all aspects of the end-to-end drill and blast process and to challenge conventional practices that limit production efficiency. As a result of the outcomes of this work, a number of initiatives were identified to improve operational practices that have also delivered significant cost savings.One such initiative was to increase pattern size to a minimum of 1 Mt where practicable, thereby creating ‘megablast’ as a new standard across all mines. To achieve blasts of this size, the team had to overcome the complex problem of integrating wall control into the megablasts.With traditional blasting techniques, the key strategy, which is also historically inefficient but was thought to be integral to having stable, safe walls, was to utilise the trim blasting/modified production blasts technique (ie narrow blasts along the pit wall designed to ‘peel off’ the material while minimising the effects of vibration and charge confinement on wall integrity).Small traditional trim patterns comprise three to four rows of production holes and one or two rows of batter/buffer holes of reduced diameter that require the firing face to be completely exposed before blasting. This is an extremely slow process that requires a lot of resources for very little tonnage while adding additional expense to the final cost per tonne.This paper will show how the megablast approach was developed to control damaging vibration and confinement effects, flyrock and fragmentation while having the largest possible blast that includes wall control. The new practice is based on a theory that involves the initiation point and control row being the second row of holes from the pit wall itself. Adjusted charges in vented batter and buffer holes help to achieve an optimal toe design, and at the same time create a zone of broken ground that absorbs damaging vibrations formed by the attached production blast of any size, whether it is a straight wall or a multi-angled complex pit shell design.Using the new style of blasting has allowed an increase in the size of the patterns from an average of 300 kt to over 1 Mt whilst maintaining pit wall integrity. Case studies will be presented showing drill, charge and tie-in designs with the presentation having additional blast videos, including overall shots of blasts and in-close footage of what happens behind the blast at the crest of the planned catchment berm.The paper will also demonstrate the flow-on effect of using this style of blasting to reduce operational costs associated with other downstream processes, such as the reduced requirements for pattern preparation, an increase in productive digging, reduced maintenance costs and a decrease in fuel burn for equipment.CITATION:Green, B, 2015. Megablasts – enabling technologies in BHP Billiton Iron Ore, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 599–606 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

A review of the most widely used global extraction sequences in sublevel is undertaken. The review includes techniques used to extract massive as well as single or multiple steeply dipping tabular orebodies. The paper also deals with thick flat lying orebodies suitable for open stoping. Techniques used to minimise the effect of stress redistributions on a global scale are discussed for all the extraction sequences analysed.

Jan 1, 2003

By D J. Black

The process of excavating and mining coal causes fractures in the overlying and underlying strata. The fractures provide pathways for gas released from coal seams and other gas-bearing strata to flow into the mine workings. Coal seam gas typically contains high concentrations of methane with lesser concentrations of carbon dioxide. Low concentrations of other gases such as nitrogen, hydrogen sulfide and ethane may also be present in some coal seams. In certain geological settings, particularly in close proximity to geological structures, such as faults and dykes, the concentration of gases contained in a coal seam can vary significantly between methane-rich to carbon dioxide-rich.In mine design and planning it is vital that mining engineers gather sufficient information to accurately determine the content and composition of the gas present in the coal seam and develop an understanding of changes in these parameters within the planned mining area.The longwall method of mining coal causes fracturing of the overlying and underlying strata behind the retreating longwall face. Where coal seams and other gas-bearing strata are present within the caving zone, gas will be released from the strata leading to contamination of the mine workings. If the rate of gas emission exceeds the diluting capacity of the mine ventilation, the concentration of gas in the mine may exceed the statutory limit, resulting in production delays and potentially unsafe conditions.CITATION:Black, D J, 2016. Planning effective management of gas emissions in an underground coalmine, in Proceedings Life-of-Mine 2016 Conference, pp 44–47 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

In presenting the paper, Mr. Davey quoted subsequent work which yielded k, at miscibility gap composition, of about 50.We can confirm the authors' findings for k j 300 for nearly pure tin to k 2 about 50 (average 47) from our own experience and from repeat experiments on materials described by the authors, at 1150°C.During laboratory-scale trials we also found confirmation of the authors' view that it is more difficult to reach equilibrium from the high-iron (in slag) side than from the low-iron (high-tin) side. Working from the high-iron side tends to yield results that point to a high k, leading to optimistic values of iron/tin ratio in final slags. In practice the smelting of a tin concentrate, unless it is exceptionally low in tin and high in iron, must yield initially a tin-rich slag and therefore equilibrium can only be reached from the "tinny" side.

Jan 1, 1967

By Kurzeme M, Willoughby D. R

Current research at the CSIRO, Division of Applied Geomechanics, into the mode of response of fill as a structural component has been based on model tests for prediction of behaviour and field observation of critical parameters. The procedure is summarised in four stages: (a) define the specific fill function (b) postulate the mode of failure (c) use models to quantify the conditions (d) monitor critical parameters to check or update the analysis in (c). The above procedure is used to postulate the failure modes of each of the possible func- tions performed by fill materials. Analytical techniques, or lines of investigation, are described for each of these modes and specific reference is made, where, possible, to an exis- ting mine environment.

Jan 1, 1973

By G Booth

Whilst communications systems in the mining industry have evolved over the years, the premise remains consistent that reliable communication is vital for safety and operational efficiency. TodayÆs open pit mines are benefiting from advanced developmental efforts based on mesh networking hardware and software technology. This paper highlights Rajant CorporationÆs adaptation of technology, originally developed for the defence and first responder industries, to provide wireless network connectivity in open pit mining applications. Featured is the large-scale deployment of over 300 mobile, meshing access points in the Bingham Canyon Copper mine near Salt Lake City, Utah, the worldÆs largest open pit copper mine. Many companies have positioned themselves, their technology and their product line in the arena of rugged outdoor wireless broadband mesh networking infrastructure. However, Rajant Corporation has combined specialised command and control software and portable networks which offer network extensibility and redundancy that are not available in any other networking solution. Rajant CorporationÆs BreadCrumb« offers unique traits in portability and non-line-of-site networking nodes which intelligently route and broadcast in standard 802.11 protocol. The advantage of RajantÆs solution is especially valuable for users needing equipment moved easily and rapidly into and out of the theatre of operations with uninterrupted network availability. The main differentiators that set the BreadCrumb« network apart from the competitors are mobility (continuous availability), simplicity, ability to properly load balance and power options. In 2007, RajantÆs BreadCrumb« wireless mesh system was selected by the Kennecott Utah Copper Corporation (KUCC), a wholly owned subsidiary of Rio Tinto, as its primary communications platform for operations within the Bingham Canyon Copper mine, the worldÆs largest open pit copper mine. The Rajant BreadCrumb« technology enables KUCC to gain additional operational efficiencies by tracking, monitoring and managing its copper mining operations. The primary goal of using the BreadCrumb« wireless mesh system Kennecott was to streamline its complex mining operations. KUCC required a high number of moving wireless nodes for improving mine monitoring and control. The Rajant InstaMesh« software running on the wireless BreadCrumb« units connects hundreds of devices to each other while rapidly transporting critical operational data. Kennecott has successfully implemented a large number of BreadCrumb« radios in an interconnected network that allows loader trucks, shovels, pumps, laptops and other production equipment to communicate with each other in real-time. These systems are a mix of secure access nodes that enable data and voice communications across a meshed, self-healing network for fleet dispatch, health monitoring and other critical mining applications. Many of the devices that require wireless communications are moving at all times throughout the wireless mining infrastructure. The BreadCrumb« nodes rapidly adapt to any changes in the network topology, assuring that IP traffic uptime and bandwidth are maximised. The installation layout and data network specifics, as well as maps and data network efficiencies will be detailed in the paper.

Jan 1, 2008

By B Belle

In a deep, gassy predrained coalmine, ventilation and goaf drainage systems act as critical controls to manage longwall (LW) panel return gas levels. The goaf capture efficiency of most LW panels ranges from 45 to 85 per cent based on the gas domain at respective workings. Recent operational experiences have indicated that 50 m goaf hole spacing is optimal for management of high production retreat gassy LW panels, where the probability of goaf hole failures are frequent. Due to the horizontal stress direction geotechnical issues, goaf hole failure just behind the LW face is a recurring challenge resulting in significant and immediate increases in LW panel return gas levels. This paper presents a successful implementation of an innovative LW tailgate (TG) road cut through seal goaf fan/venturi system. The system incorporated a 17' (400 mm cased) hole drilled to 320 m deep in a perimeter roadway on a retreating LW TG road drawing the working seam horizon goaf gas behind the perimeter of seals. The surface goaf fan/venturi system was aimed to safely exhaust the LW deep goaf gas and thus withhold the goaf stream spillage to TG drive area and reduce the panel gas load by controlled operation of the system using continuous monitoring of CH4, CO and O2 levels. This control philosophy was made operational without impacting the use of the perimeter inbye ventilation shaft used for mine cooling and providing additional ventilation dilution capacity. The instantaneous reduction in TG gas levels of up to 0.3 per cent was observed even when the LW was 300 m away from the c/t seal goaf hole. Success of this concept TG seal goaf gas control system used even when the LW was 1300 m outbye has become an inventory of additional control for future deep and long LW blocks. This paper attempts to share the design process in addressing other risks and desired outcomes in managing the LW gas levels.CITATION:Belle, B, 2015. Innovative tailgate mobile goaf gas management in two gate road longwall panels – concept to implementation, in Proceedings The Australian Mine Ventilation Conference, pp 31–40 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By D Lees, D Gilchrist

Sydney has hundreds of kilometres of sewer tunnels. Many of these are over 50 years old and some have been in service for more than 100 years. The tunnels are predominantly constructed in Hawkesbury Sandstone and many are unlined.Principles have been developed over many years for the safety factor required in designing and constructing new tunnels but these do not necessarily relate to the operation and maintenance of existing tunnels, and in particular those that do not necessarily require personnel access for anything other than regular inspections.Assessment of the stability of these established tunnels needs to take account of their size, their age, their function, and their method of construction, as well as the geology in which they are situated and any support measures which have been installed. More importantly a stability review needs to take account of the consequences of a collapse, with regard to the inspection process, carrying out of any required repairs and the long-term performance of the tunnel.This paper is based upon the authors’ experiences inspecting and reviewing more than 200 km of tunnel in the last ten years. It will show some of the procedures and methods adopted by Sydney Water, how these can be presented as an acceptable procedure in line with other safety standards, and how they might be adopted for other similar historic rock tunnels.CITATION:Gilchrist, D and Lees, D, 2014. The development of a procedure for the inspection of unlined rock service tunnels, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 543–552 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By R Hughes

"Spring Creek Mine uses high pressure water to extract the thick Main seam in the Upper Rewanuicoal measures. The extraction method results in the creation of large voids which collapsespontaneously. This can result in the displacement of large volumes of methane, which may create a signifi cant hazard if not correctly managed. A system of automatic dilution doors is employed to mitigate this risk. This paper describes the evolution of the system and gives some examples of its eff ectiveness."

Jun 1, 2012

By B Jones, M Chappell

Permanent rock bolts used to support rock tunnels are required to perform for the design life of the structure as a minimum. Quality of installation is critical to the performance over the life of the rock bolt.This paper will present the findings from an in investigation into the integrity of rock bolts installed in an underground hydroelectric power station cavern and access tunnel. The 25?mm diameter rock bolts were installed 50 years ago, tensioned and post cement grouted. Due to a major machine upgrade the whole facility was subject to an asset survey. The owners are responsible for managing the risks associated with the failure of these rock bolts and ensuring the structural integrity of the tunnels and caverns is maintained to continue operations, protect machinery, assure production and more importantly maintain a safe working environment for all employees and visitors.To help manage risk a proactive approach is desired. To this end a test schedule using a non-destructive testing (NDT) system was carried out by Independent Integrity Testing Pty Ltd (i2t). The system used in this application was RokTel™. The system operates by applying a small axial impact to the rock bolt end and measuring the resultant acceleration response. The rock bolt characteristics affect the acceleration response.The data output from the system is analysed principally using Fourier Analysis (FFT) and sinusoidal waves. The energy generated in the bar, the rate of damping and changes in frequency are all assessed. Testing was carried out on 70 rock bolts within the tunnel and cavern. A selection were then over cored, photographed and documented. The data gathered from the testing is then correlated with physical evidence to establish a calibration for the remainder of the rock bolts and assess if this is a viable method for identifying defective elements, and what degree of accuracy can be achieved. The findings will assist with the future assessment of similar hard rock underground?facilities.CITATION:Jones, B and Chappell, M, 2014. The use of non-destructive testing to identify defective rock bolts – a case study, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 275–280 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By Yinxiang W, Chunlai Y

In older to improve efficiency of surface pre--grouting in sealing off water in heavily water-bearing strata, such as sandstone,siltstone and limestone, several methods have been used in China, they are ; intermittent pre-grouting, adjusting pre-grouting parameters and stepwise repeated pre-grouting methods. The paper describes effect of deviation on water sealing in pre-grouting. Deviation correction measures, like mechanical, technological and changing hole position methods have been introduced with satisfactory results in practical engineering projects without increasing the volume of engineering project and without causing delay.

Jan 1, 1988

By M Wortley, J McKay, D La Rosa, O Guyo

It has been a generally held concept that crushing operations were, by their nature, too simple to benefit from the implementation of advanced process control. The commissioning of an OCS¬ expert control system and image-based oversize detection system, VisioRock, at the Pilbara Iron Tom Price facility are dispelling these notions. A constraint-based OCS¬ expert control system has been designed and commissioned on the high-grade crushing and screening plant along with a vision-based oversize detection system functioning on six product conveyor belts. To date, the expert control has demonstrated the ability to increase production by maximising dynamic constraint utilisation. Dynamic constraint utilisation is a concept developed by Rio Tinto Technical Services for effectively evaluating constraint-based control logic performance. The VisioRock system has been installed and configured and has been operating for a period of several months. Currently, Tom Price and Metso personnel are working to define correct oversize detection thresholds. Details of the plant implementation are discussed.

Jan 1, 2005

By B Young

Variable bench heights, interaction with underground workings and a steeply dipping orebody are challenges faced daily by geologists at Xstrata Zinc’s Black Star Open Cut (BSOC) Zinc/Lead/Silver mine in Mount Isa, Queensland.BSOC has been in operation since late 2004 and was developed to extract the surface extents of the Zn/Pb/Ag mineralisation mined in the underground lead mine. To date many large scale stopes and extensive development drives have been intersected and successfully mined. The stratigraphically hosted orebodies strike in a north-north westerly direction, dipping ~75° west. Ore production from the pit is currently at 4.5 Mt/a.Historically, sampling was conducted using a multiple spear technique from blasthole cuttings. This method proved to be relatively reliable when blasting benches at a consistent height, but a requirement to vary bench heights to safely collapse and then mine through underground workings reduced sample representivity to unacceptable levels.The purchase and commissioning of a production rig which had been converted for reverse circulation (RC) has allowed for the flexibility of a small rig, with the capacity to easily drill 48 m holes while ensuring sample quality. Sample quality is not the only benefit of introducing RC grade control. By collecting grade control data well in advance, informed decisions can be made by planning, drill and blast and mining departments weeks beforehand, rather than hours before firing. Additionally, seeking operational value to offset higher drilling costs has proved positive with benefits including increased confidence in orebody wireframes, accurate tonnage and grade for proceeding five benches along with the ability to representatively test metallurgical response on a tight grid spacing.

Aug 22, 2011

By L Sandery, S Light

Within 22 months of commencing decline development, the Prominent Hill Ankata Underground Project achieved its full production rate of 1.2 Mt/a.In 2010 construction of the Ankata Underground Project was approved. Decline development commenced in November 2010 and the turnout for the first sublevel was reached by August 2011. The first stoping ore was produced in the first quarter of 2012 and production was successfully ramped up to full production during the third quarter of 2012.Diamond drilling commenced in October 2011 and was conducted concurrently with the underground development. This presented challenges as mining and production targets had to be balanced with underground exploration activities. To achieve production on schedule, without adversely affecting the diamond drilling program and future development, meticulous and adaptive planning techniques were required. This included involvement from engineers, geologists, underground operators and underground diamond drillers.The granularity of these planning techniques allowed the management and prioritisation of development and diamond drilling down to an almost hourly basis. A constant flow of information from drill assay results was fed back into the planning systems. This resulted in a constantly evolving mine plan as the orebody was further refined. High priority areas were identified and targeted to allow continued development and a successful rapid ramp up to full production.CITATION:Sandery, L and Light, S, 2014. Managing the diamond drilling interactions in commissioning the Ankata underground mine, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 75–80 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By T Connor

Alkali emissions are one of the environmental challenges facing alumina refineries. Queensland Alumina Limited (QAL) is undertaking a number of initiatives to continuously improve its environmental performance. One of these is a program aimed at the reduction of alkali emissions. Alkali emissions originate from a number of sources (eg elevated open tanks), and its level depends on a number of process parameters/ mechanisms (ie splash filling, thermal currents in tanks, streams discharged from a pipe, tank temperatures, atomisation) and climatic conditions (eg wind speed and direction, rain, etc). Under normal operating conditions, there is a continuous low level of alkali emissions from the plant. Certain vessels within the plant have been identified as major contributors to this level of emission, while certain activities within the plant contribute to a temporary elevation (æspikeÆ) of alkali emissions. QAL developed a method using phenolphthalein-treated pads to measure emissions within and outside QAL boundaries. These provide no information about mass emission rates but are important for detecting if alkali material is present. Since mass emission rates are important for determining if improvements in emissions are made, QAL identified the need to design an improved sampling method. Following the development and implementation of a sampling and analysis method to monitor alkali emission concentrations, QAL is conducting a number of feasibility studies evaluating a range of alkali emission reduction options. The alkali measurement method will be used to track and demonstrate progress in this environmental initiative. This paper will discuss the measurement method and emission reduction options being evaluated.

Jan 1, 2005