Search Documents

By Giuli M, Barnaba P, Sacerdote R, Tammaro F

Following a theoretical consideration of the effect of flooding, fluidisation and softening on blast furnace blowing limits, results are presented which show the effect of these parameters on operation. Industrial trials on Oscar Sinigaglia No. 4 BF are reported and results compared with those obtained theoretically and in the laboratory. It is shown that in these trials the furnace operated at levels of fluidisation very much (80-90%) below those theoretically calculated whereas in some cases (high proportion of sinter) actual hot metal output was near the calculated flooding limit. However, it was observed that as the sinter percentage decreases also actual productivity becomes lower than the one caused by flooding. This gap, which increases as other ferrous components (essentially acidic) replace the basic sinter was explained by the softening of the burden under bosh conditions. Softening indices measured on the individual materials yield support to this explanation. Coke rates data show that for approximately every one percent increase in the basic sinter in place of blended sized ore, a coke rate decrease of 1.1 kg/thm results. For acidic pellets this value is 0.6 kg/thm. Results of breakdown and reduction characteristics are also given and their indices compared with actual pt oduction. Measures to improve operations are proposed.

Jan 1, 1975

By Prosser AP

The large body of knowledge about the relation between chemical process efficiency and mineralogical features is of only limited use. The profession ought to try to improve the methods of using information as well as adding to the knowledge. One attempt isòdescribed. Correlations between process efficiency factors and the mineralogical features of low- grade concentrates have been developed from both a theoretical analysis and experimental measurements. The ultimate recovery of a reactive phase in an inert matrix can be calcu- lated from simple measurements of the particle size, porosity and pore size of the concentrate, and the grain size of the reactive mineral., The rate of recovery, up to 98% recovery, can be calculated from simple measurements of particle size, porosity, proportion of reactive mineral and tortuosity. Some details are given. The correlations are of potential use in process selection and preliminary design. Satisfactory predictions have been made for near-ideal systems. Improvements in the measurement of pore size and tests on more realistic materials are required. The ultimate benefit of the correlations will be determined by the magnitude and frequency of the effects of mineralogical features other than those specified above.

Jan 1, 1975

The operation of quarries for the production of crushed stone and aggregates, depends heavily on rock blasting efficiency, which usually represents a major share of total production costs. After investigating the causes of this situation, a series of technical aspects have been detected, and they are described for the purpose of contributing to the minimization of costs, which also reduces the effects of blasting on the environment. Utilization of empirical design methods, of inadequate explosive types, and of erroneous drilling pauems with respect to rock properties, are the main factors to be corrected, as a consequence of poor engineering criteria, with scarce use of computational methods and field instrumentation. Several concepts of blasting optimization are pointed out, and their application to industrial operations in a Portuguese limestone quarry indicated clear trends for the reduction of production costs, as well as some of the deleterious consequences of blasting on the environment.

Jan 1, 1990

By Grant J

In surface mining, significant improvements in efficiency can be obtained through greater control over the formation of the muckpile. By tailoring the muckpile shape and its looseness to the requirements of the excavating equipment savings can be rea- lised through increased production, machine life and reduced maintenance. For instance, one open cut coal mine has recently estimated that a 2001o improvement in its front row throw would realise $320,000/year savings in rehandle costs alone. Previously greater throw has been achieved by increasing the powder factor through increased quantity of explosive or by drill- ing a larger number of holes-both at a significant cost penalty. However a recent series of experimental blasts demonstrated that it was possible to achieve a twofold increase in the distance of throw of a single row blast by simply changing delay timing alone. The Nobel Electronic Delay Detonator was used to provide the timing flexibility and control required for a thorough study of the effect of blast timing on heave. Whilst it is well accepted that the front row of a blast dominates the extent of throw, it was also found that the profile of the blast could be significantly altered. To date, the general consensus has been that the muckpile for- mation from a blast is a function of the blast geometry, the rock type, the explosive and the initiation sequence. Typically the geometry, rock type and initiation system have a far greater impact than the explosive type. This has been demonstrated by many high speed film studies. However the extent of influence via initiation has rarely been fully evaluated, owing largely to the limited control offered by conventional detonators.

Jan 1, 1988

The mineralogy of regolith material for which whole rock geochemistry has already been done can be used to better understand/rank the significance of geochemical anomalies. Case studies show that the secondary minerals of the regolith environment have quite different capacities to incorporate pathfinder and target elements, eg hematite appears to be a better host to Pb than goethite and Pb rich alunite-jarosite minerals are a better Ag host than mimetite. Thus correlations between elements in regolith material may be strongly affected by mineralogy. Understanding of the significance of a geochemical anomaly is frequently enhanced by knowledge of the weathering susceptibility of different minerals. For example, when a mineralogical sequence which does not correspond to the expected order is found (eg feldspar overlying weathered material without feldspars) it is possible that transported material is present in the profile. Such mineralogical information is particularly relevant as exploration continues into areas of thick regolith.

Jan 1, 1997

By Bourke J. H, Ashcroft T. B

Many changes have occurred in the world market for manganese over the last five years. Among these, the emergence of divided steel processes for the hot metal refining of pig iron is affecting the use of both ferruginous manganese ore and ferro manganese, at this stage particularly in the Japanese steel industry. Subsequent demand for higher quality manganese materials is promoting the use of thermally beneficiated products such as sinter. In addition, many processes are being developed for the direct smelting of fine manganese ores, of which plasma technology is the most advanced. Cost pressures and product quality requirements are encouraging pre- viously self sufficient countries such as The People's Republic of China and the USSR to import high grade manganese ores to supplement indigenous lower quality supplies. At the same time, Brazil has been provided with the impetus to convert its substantial reserves of ore to value added products.

Jan 1, 1988

The mining industry is quite often faced with declining selling prices for its products in the face of rising prices for the input cost resources that it uses. Blasting is a key activity within the mining system and has a vital role to play within the Mine to MillTM concept. It is therefore important that blasting makes a positive contribution to mine profit and productivity. There are several variables involved in considering the profitability and productivity of blasting. The rock types and structures, the bench height, the blast hole drill rig specifications, hole diameter, spacing and burden, explosive loading and initiation and blast size fragmentation. Productivity accounting is a methodology which is used elsewhere to give additional insights into the productivity and pricing factors that drive the financial performance of a business. Miners know intuitively that productivity and pricing influence costs and profit, but only with productivity accounting can the dollars involved be calculated. Drilling and blasting are part of a chain of unit operations in a mine. For an owner-miner, drilling and blasting would be considered as cost centres and a productivity accounting cost model approach would be relevant. On the other hand a contractor is likely to consider drilling and blasting as a profit centre, in which case a productivity accounting profit model approach would be appropriate. Both of these will be explained. The paper provides a basic outline of deterministic productivity accounting and demonstrates its application to blasting. Drilling and blasting data from a mine was obtained for a two-month period. The change in productivity and prices was calculated to obtain the dollar contributions from them towards the change in cost. It was determined that although there had been productivity dollar gains these were offset by larger pricing dollar losses, the net effect being that total drilling and blasting costs increased. The productivity accounting analysis gives the facts and the mine is in a position to establish priorities based on knowing the dollar contributions of each input used.

Jan 1, 2001

By D Feng, G C. Lukey, J S. J, R R. Dagastine

An ongoing challenge in the coal industry is pyrite removal using the flotation method for fine particles. The use of a æseparation in frothÆ (SIF) technique to recover coarse particles of up to a few millimetres in size has presented a potential solution. However the commercial success of SIF is still limited due to the poor understanding of the separation mechanism. The particle floatability in SIF is determined by the constructive or destructive stresses resulting from the forces exerted by the particle on the bubble films. Hence, the surfactant properties and the mineral characteristics (eg hydrophobicity, shape, etc) are the key factors that control the interaction between the particle and froth. In the present work, the interaction forces between different particles (ie crushed glass, pyrite and coal) and a single air bubble are measured in a non-ionic surfactant solution (pentaethylene glycol mono n-dodecyl ether, C12E5) using an atomic force microscope (AFM). Experimental results show that the interaction is primarily dependent on the contact angle (ie the degree of hydrophobicity of the minerals). For crushed glass, the transition from repulsion to attraction was observed as the contact angle increased. As the concentration of C12E5 increased, the adhesion force was suppressed due to wrapping effect. For coal and pyrite with much higher hydrophobicity, long-range attraction was observed. The effect of shape factor was only visible at high surfactant coverage where sign of destabilisation became noticeable on the retracting force curve. These results provide a fundamental understanding of the direct interaction forces of a complex real system between an irregular particle of either crushed glass, pyrite or coal and a single air bubble. Theories developed for interpretation and modelling are thus far based upon the study of ideal systems of glass or polystyrene spheres and an air bubble and were incapable of explaining the interactions in complex real systems. The presented measurements were a first approach to the problem of real mineral-bubble interaction in flotation systems. Thus, the results can only best be interpreted semi-quantitatively.

Jan 1, 2005

With mining development on hold and other underground works in a slowdown, the develop- ment of nuclear waste repositories takes center stage on the American rock engineering scene. Three repositories for commercial spent fuel -- in salt, tuff, and basalt -- are in the phase of site characterization and conceptual design, and one pilot project for defense high-level waste in salt is under construction. A repository design for crystal line rock has recently been postponed. Because of strict quality assurance requirements throughout design and construc- tion, and because of the need to predict and ascertain in advance the satisfactory perfor- mance of the underground openings, much intellectual energy has been expended to analyze underground openings in the unusual circumstances of the repository environment. In the long term, these efforts will lead to an improved understanding of rock behavior and improved methods of underground analysis and design. For the shorter term, a formalized ground control plan was developed, the princi- ples of which may be applied to other types of projects. This paper summarizes the status of underground design and construction for nuclear waste repositories and presents some details of the ground control plan and its individual elements.

Jan 1, 1987

By Koh P. T L, Varnas S. R

Fluid flow, heat transfer and combustion in a nickel flash smelter have been investigated by numerical modelling and flow visualisation. The three-dimensional numerical model incorporates turbulent two-phase fluid dynamics, radiative heat transfer and combustion. The main features include the use of the k-E turbulence model, the Lagrangian tracking of particles, radiative heat transfer based on the spherical harmonics method, and chemical reactions. The predicted flow fields are in good agreement with data obtained from a series of flow visualisation experiments on a cold water model. The interaction mechanism between the fluid flow and the solid particles is examined for a range of particle sizes both with and without injected oil in a series of simulations. The heat transfer in the shaft is dominated by combustion and radiation, whereas the ignition of particles is influenced by the particle size and the added oil. Flow and temperature fields for both gas and solid particles are presented as well as the fraction of sulphur removed from the particles.

Jan 1, 1992

By Clifford C. E

The Black Star and Racecourse orebodies below 15 level contain a major portion of the primary silver-lead-zinc ore reserves of 56 million tonnes at 150 g/t Ag, 6.4% Pb and 6.5% Zn at Isa Mine. Extraction from this area is scheduled to begin in the early 1980's. Mining in this block will be quite com- plicated as the ore is contained in a dozen separate orebodies varying in width from 3 m to 20 m with only narrow barren pillars between them in some cases. Mining objectives which consider metal recovery, costs, environmental and safety factors, operating requirements and rock mechanics are used to compare proposals. The planning work involved in formulating mining proposals considers disposition of reserves, scheduling factors, sequence of extraction, extraction methods, haulage set-up and ventilation requirements.

Jan 1, 1979

By Chaves AP

This paper describes an investigation on the surface properties and mechanisms involved in the agglomeration of iron ore. For this purpose, an organic binder (carboxyl-methyl-cellulose (CMC)) was used in substitution of bentonite, the classic binder in iron ore concentrate agglomeration. Recently, a renewed interest of the iron ore producers in Brazil to replace bentonite for an organic binder, because of the economy that can be achieved in the, blast furnace operation. These savings are mainly due to the lower aluminum silicate addition which decreases slag volume and the improved pellet metallurgical properties which have the potential for lowering hot-metal production costs. Also organic binders are effective at lower addition levels, which results in lower storage and transportation costs. It is very important in Brazil because of the vast geographical area since transportation is made mainly by truck. Another advantage of organic binders is that they have low ash contents, and therefore most of the binders bum. off during the pellet firing operation. Previous studies have demonstrated the possibilities of the use of CIVIC, but in addition to its high cost, the pellets presented improper behavior at high temperatures or when prepared with high moisture levels. In the investigation here described, these problems have been solved through the addition of other reagents to CMC.

Jan 1, 1993

By McDonough RJ

Mechanical agitation is the preferred system for Carbon-in-Pulp processes. Agitator design requires an understanding of the relationships between energy, shear and flow and the nature of shear rates and shear stress distribution in an agitated tank. Laser techniques are useful when studying these phenomena. The alternatives are open impeller agitation or draft tube circulation. Each has advantages and disadvantages but both require careful choice of impeller and system geometry. Overall the draft tube circulator is the more attractive in many cases. Open impeller agitators are designed in accordance with established procedures for mineral slurries taking due account of shear effects in tanks containing carbon. Preferred tank proportions are 1:1. Circulator design methods were developed in the alumina industry before being applied to CIP processes. Optimum draft tube diameter is critical to power requirements. The overall system must be designed as an axial flow pump operating in a closed circuit. Such a system exhibits quite characteristic behaviour which requires an impeller of varying pitch angle and aerofoil section for best stability and efficiency.' Tank height may be 2 or more times diameter. Resuspension of settled solids can be assisted by a series of slots in the draft tube. These slots have the secondary effect of stabilizing hydraulic behaviour and reducing installed power requirements.

Jan 1, 1982

By Denby B, Hollands R. Schofield D

Surface mines are in operation worldwide, the vast majority employ large haul trucks for the transfer of material both to the outside world and around the site. The sheer size of these trucks and the operating conditions means there is a high

Jan 1, 1998

Since the announcement of early experimental work on rotating magnetic field (RMF) separation at the Sixth Mill OperatorsÆ Conference in 1997, the concept of RMF separation has been developed and tested further, and a range of separator designs is now being developed for the mineral processing industry. Shortened, but full diameter, prototypes of these designs are now available for test separations. The main advantage of RMF low and medium intensity attraction separation is the significant reduction in particle entrapment. This reduction is so significant that RMF separators are capable of operating very close to their theoretical limit for separator precision. This makes small laboratory RMF attraction separators ideal for low to medium intensity magnetic sample analysis, and larger separators ideal for applications requiring sharp magnetic susceptibility splits. Feedrates and separation rates are comparable to those of conventional attraction separators. Although RMF attraction separators are now well advanced in development, RMF rotation separation is still in the early experimental stage. The exception to this is the dry particle rotation eddy current separator that offers eddy current separation of small non-ferrous metallic particles from about 2 mm down to about 100 microns. Wet small particle eddy current separation is also possible, but has not yet been developed to a practical stage.

Jan 1, 2000

By D P. Obeng, L Reemeyer, R Holmes

The Zinifex Century Mine employs a large number of Detritor mills for fine and ultra-fine grinding to liberate silica and sphalerite at 80 per cent passing 7.5 microns before final zinc flotation. A joint project between CSIRO Minerals and the Zinifex Century Mine was carried out to evaluate the Detritor mill performance. Plant surveys were conducted around the Detritors in conjunction with laboratory tests. The survey data showed that the Detritors in the ultra-fine milling circuit performed well. They reduced a feed F80 sizing of 46 microns to a product P80 sizing of 7.5 microns at a gross energy consumption of 37.2 kWh/t. Scale-up of ultra-fine milling Detritors was studied using a 0.55 kW laboratory batch unit and a 355 kW full-scale Detritor by processing Century zinc concentrate with 1 mm sand media. The results indicated that the 0.55 kW laboratory mill underestimated the energy consumption of the full-scale Detritor by about 20 per cent for a product P80 of seven microns. The performances of a horizontal IsaMill and a vertical Detritor were compared as ultra-fine milling devices for processing Century zinc concentrate. The experimental data demonstrated that, when using the same grinding media, the energy efficiency of the two mills is similar despite the difference in mill designs. The Detritors used for regrind duty at the Century Mine performed poorly when processing feed at 80 per cent passing 88 micron. The energy consumption was high and the product size distribution was broad with particles above 100 microns in the feed unbroken and particles below ten microns overground. A coarser ceramic media of 3 mm was therefore tested in a laboratory Detritor to process the regrind Detritor feed as an alternative to the 1 mm Colorado sand used at the Century Mine. The ceramic media reduced the energy consumption significantly and produced a narrower product size distribution, which is more desirable for the downstream flotation process.

Jan 1, 2007

By D Wei

Large tonnages of low-grade haematite ores need to be treated every day in China. One of the mineralogical characteristics of these haematite ores is that the grain size of haematite is smaller than that of quartz and is not uniform in the ores. Therefore, a flow sheet consisting of gravity concentration, low-intensity magnetic separation, high-intensity magnetic separation and reverse flotation is mainly used to separate haematite ores in China, to obtain acceptable beneficiation performance and reduce the operating costs. Nowadays, whether based on mineral processing practice or theoretical analysis, the results show that the application of the above-mentioned flow sheet is able to take full advantage of these mineral processing methods and achieves satisfactory benefi ciation of haematite ores. For example, when the iron grade of the haematite ore is about 29 per cent Fe, a concentrate assaying 68 per cent Fe can be obtained and the recovery of iron is over 80 per cent. In the future, research work on the beneficiation of haematite ores should focus on investigating the most feasible particle size for gravity concentration circuit feed so that the operating costs can be reduced and ultimately the separation performance can be improved.

Jul 11, 2011

By Koppe J. C

This study presents the procedure of mine modelling and reserve evaluation by means of statistics, computer interpolation methods and aerophotography interpretation. All data are from Carbonifera Treviso, Laura Muller City, Santa Catarina State, southernmost Brazil. From 22 bore holes and nine trenches opened in the coal seam outcrops, a data base including level references and thickness of all rock formations was created.Using this information, basic statistic analysis was carried out, showing that there are three different populations (three modal distribution). These populations defined three geological blocks with different characteristics of overburden removal and mining methodology. This mathematical approach for analysing geological data is very important for correct mine planning and complementary prospection.

Jan 1, 1993

By Baafi E. Y

A heuristic approach for the optimisation of the stope geometry is presented. The heuristic method uses economic model of a given deposit to search for the best combination of mining blocks that results in the maximum profit while imposing geo

Jan 1, 1998

Comminution Kinetics equations are developed to take into account difference of grindability of mineral components. The equations describing both batch and closed circuit grinding or crushing processes are given. These equations are applied to industrial data to derive comminution kinetic and classification characteristics of the component minerals in a multi-mineral ore. Control strategy based on these concepts is presented.

Jan 1, 1985