Search Documents

A system for rapid on-line determination of weight percentage coal in slurry and weight percentage ash in coal has been developed at the Julius Kruttschnitt Mineral Research Centre, University of Queensland. The gauging system is suitable for use with coal flotation slurries or slurries having a maximum particle size of about 1 millimeter. The system is based upon measurement of gamma ray transmission; radioisotope sources emitting photons of two widely different energies are employed. The inaccuracies of measurement that would normally result from variable amounts of air entrained in the slurry are substantially reduced by pressurising the slurry to approximately 2MPa (300 psi) using a Mono pump. The equipment can be used to make measurements on more than one slurry stream by pumping streams sequent- ially. The system is being tested at the Peak Downs Mine of the Utah Development Company in Central Queensland. This paper describes the theoretical principles of the gauge design, the experience gained to date in the commissioning of the equipment, including the installation of a PDP 11/03 computer, and the progress made in developing satisfactory interpretations of the gauge count-rate output.

Jan 1, 1978

Mining software packages are used extensively in industry for resource estimation as well as for mine design and operation. Research undertaken in the W H Bryan Mining Geology Research Unit at the University of Queensland has shown that modifi

Jan 1, 1994

By Moxon N. T, Berndt J. R

BHP-Utah Coal Limited's Peak Downs Mine is located in Cen- tral Queensland, approximately 200 km south west of Mackay. The annual raw coal production of the mine is over 8 million tpa, requiring the removal of about 40 million cubic metres of prime overburden. This is achieved through the use of five large draglines. The large depths of overburden (up to 55 metres) encountered over half the strike length of the mine enables cast blasting to be carried out in conjunction with draglines employ- ing the chopping method of digging. The objective of cast blast- ing is to use explosive energy to move as much material directly into spoil as possible. The additional costs of drilling and blast- ing are offset by reducing dragline rehandle. Two factors which are of primary importance to the design of cast blasts are initiation control and material velocity. High speed motion picture photography is a powerful diagnostic tool to quantify these aspects of blasting (Winzer, Montenyohl and Ritter, 1979; Chiappetta et al., 1983; Anon., 1983). The objec- tives of such analysis are to: 1. Determine the burden velocity, 2. Determine the time to initial movement (that is, the inter- val between a face hole firing and the initial movement of the burden), 3. Check the accuracy of the initiation sequence. BHP Central Research Laboratories (CRL) and Peak Downs Mine monitored a cast blast in the mine's Winchester Pit on 18 August, 1988. The objectives of this exercise were to: 1. Quantify current cast blast performance, providing a base case for comparison with modified blast design. 2. Compare two orientations of angled holes within the blast. 3. Assess the effectiveness of cast blasting utilising an air-deck. 4. Check blast timing with respect to burden movement times.

Jan 1, 1989

By N J. Beukes, S T. Netshio, M O. de Kock

The Thabazimbi iron ore deposit comprises a series of stratabound orebodies, on average 18 - 25 m thick that are aligned along the faulted basal contact between the Penge Iron Formation and dolostones of the Malmani Subgroup, Transvaal Supergroup. Field geological relationships and petrographic observations suggest that the formation of high-grade iron ores took place after contact metamorphism related to the intrusion of the Bushveld Complex (2.06 Ga) but before the deposition of red beds of the Waterberg Group at ca 1.9 Ga. Hard, high-grade iron ores are predominantly composed of martite and microplaty hematite. Goethite is restricted to supergene-modified ores close to the Late Cretaceous û Early Cenozoic Old African land surface. At depth, the high-grade hematite ores interfinger with low-grade dolomite-hematite and calcite-hematite ores. Iron oxides (martite, microplaty hematite) present in these low-grade ores are texturally indistinguishable from those in the associated high-grade ores, ie ore formation is genetically associated with carbonate metasomatism. Microthermometric studies of fluid inclusions in sparitic carbonates and rare megaquartz reveal their hydrothermal origin. Two compositionally distinct aqueous fluids of shallow crustal origin are identified, namely a Ca-Na-rich high-salinity brine (26 wt per cent NaClequivalent, TH ~160¦C), and an aqueous Mg-K-bearing fluid of intermediate salinity (8.3 - 12.6 wt per cent NaClequivalent, TH~120 - 150¦C). The results confirm that high-grade hematite orebodies at the Thabazimbi deposit owe their origin to an event of extensive oxidative carbonate metasomatism (calcification), similar to that recognised at other important high-grade iron ore deposits in the world. Hydrothermal ore formation is both structurally and lithologically controlled. Size and quality of the orebodies was improved by Late Mesozoic-Cenozoic deep lateritic weathering as carbonate-hematite ores were enriched to friable high-grade ores, but this supergene modification is second in importance compared to the primary event of hydrothermal ore formation.

Jan 1, 2005

By Yaroshenko YuG, Bokovikov BA, Gordon YaM

Problems of the effect of the number of tuyeres and their parameters on the uni- formity of gas distribution are invest- igated with the use of the authors' devel- oped mathematical model of the movement of gases and materials in the blast furnace. It is shown that the improvement of uni- formity of gas distribution with an increase in the number of tuyeres has a damping character. An analysis of the errors of the specified assumptions of the hypothesis concerning the potentiality of the gas movement in the bed is carried out. It is established that the potential approach model gives good results with the determination of the discharge of gas and its stress field, but is not useful for the calculation of local velocities of gas in the raceway. The results of trials of calculation investigations of the dynamics of form- ation of the raceway and the voidageòfield in beds of burden materials are presented in the concluding part of the paper.

Jan 1, 1981

An integrated mining equipment development organisation is typified by Deutsche Montsn Technologic of Essen, Germany. working on improvements in reliability, production and control in coal mines. Examples of recent mining advances are in mechanised roadheading, in different approaches to cutting technology, and in low height roof bolting.On the longwall face the mechanics of cutting are related to supplied energy as well as to dust make. In conveying both armoured face conveyors and conveyor belts are monitored. Roof support is not neglected and the continuous pumping of stowage slurries provides further options for longwall support. Surveying developments, particularly the gyro-theodolite, directional drilling. and shaft vehicle monitoring provide further examples of advances in control in coal mining activities.

Jan 1, 1991

By I M. Platten, Y Xie, B W. Cuffley, S C. Dominy

"Geometallurgical programs require the collection of representative samples for geochemical, mineralogical and metallurgical test work. Such protocols must be designed to suit the style of orebody in question. The distribution, proportion and size of gold particles have a direct impact on the effectiveness of sampling and test work protocols, and the gold recovery processes employed. Characterisation studies focusing on ore mineralogy, and gold particle deportment, size and distribution are required. High resolution X-ray computed tomography provides a non-destructive method for analysing the 3D nature of gold in rock samples. It can be used to calculate the modal abundance, particle size and distribution of gold in the sample volume. This paper presents a case study of the imaging of in situ gold particles in a high-grade gold ore. The Nick O’Time reef system comprises laminated quartz veins, which locally bear extreme grades of up to 100 oz/t gold. The mineralisation has previously been characterised from both a mineralogical and metallurgical perspective. Eight visible gold-bearing vein samples were scanned using X-ray microtomography. Microtomographic data were integrated with previous mineralogical and metallurgical test work outputs.CITATION:Dominy, S C, Platten, I M, Xie, Y, Cuffley, B W and O’Connor, L, 2016. Characterisation of Gold Ore from the Nick O’Time Shoot (Tarnagulla, Australia) Using High Resolution X-ray Computed Tomography, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 241–254 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By L I. Rozman

"There have always been development projects that fall short of expectations. In the last decade, we have seen more than the usual number of mining and oil/gas development projects taking significantly longer to develop and costing materially more than expected. The recent resource-equity market slump proves that investors are now far more cautious about investing new capital in the mineral and petroleum resources sector.What have we learned since 2005? Why have projects missed their targets? Why do investors often feel misled?Valuation of a project and the estimation of value is a more complex process than the evaluation of the merits of project development. The merit of project development can be clear from a prefeasibility evaluation, but this is no reason to skip the rigour of a feasibility study. The valuation of any project that is developed with any added risk should be discounted for this added risk.The development of a project impacts on other stakeholders, and the indirect cost of these impacts can have material implications for the cost structure, time and ultimate valuation of the project for its financial backers. The development of new projects (and thereby supply) can also have an impact on commodity prices, and therefore an impact on returns for financial backers.This paper will provide commentary on the author’s experiences and observations as a project developer and operator for 25 years, before becoming a project financier a decade ago.CITATION:Rozman, L I, 2016. Project evaluation and valuation – an investor’s golden rule, in Proceedings Project Evaluation 2016, pp 31–36 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

By Drew GJ

Smelting is a process in which heat is applied to ores to produce metals. Impurities are removed by segregation in the slag, or converted to gases or sublimates and discharged up the flues. Mate- rials delivered into the smelter have generally been previously concentrated or processed at the mine, and the size of their particles, and also their chem- ical composition, greatly affect the smelting proc- ess. Some impurities are more difficult to remove than others, and are more objectionable in the finished product. The first metal mine in Australia was opened near Glen Osmond in South Australia in 1841, for silver-lead ore. It was followed by the Kapunda Mine for copper in 1844 and by the very signifi- cant Burra Mine, also for copper, in 1845 (Figure 1). A major part of their ores could not be exported profitably for smelting in England and Wales where the large smelters were then located. In addition to treating ores from Cornwall these also smelted ores from recently opened mines in Cuba, Chile, and Mexico. The Welsh smelting process (Figure 2) was developed over a period of years to utilise Welsh coal to treat copper ores particularly from Corn- wall. The first step consisted of a calcination to remove sufficient sulphur from sulphide ores so that subsequent melting operations would produce copper matte, a copper-iron-sulphide which melted at about 1050¦C. Subsequently refined to white metal with the addition of carbonate and oxide ores when these were available, and often through an intermediate step of blue metal, this matte was finally oxidised to pure copper, or as pure as it could be made in those days. The movement of metal towards greater purity was matched by a reverse flow of slag, carrying reducing quantities of copper, so that the slag rejected from the first melting process carried the minimum quantity of copper. Chemical analysis was virtually unknown. Materials were assayed in the laboratory by a small scale smelting process, and the purity of the final refined copper was judged b} the ease with Mhich it could be hammered into thin sheets.

Jan 1, 1987

This paper first describes the essentials of the slurry shield method and its achievements, then problems encountered during driving tunnels and their countermeasures, and finally shows problems to be solved in the future. The author works at Tekken Construction Co., Ltd. as a director. All the data cited are based on material gained from the slurry shield tunneling works undertaken by the said company. The mark, viz*, indicates that Tekken Construction Co., Ltd. has obtained or is applying for a patent in the U.S., Europe and Japan. 1. CONSTRUCTION RECORDS BY SLURRY SHIELD METHOD AND ITS PROBLEMS (1) Shield machines in the future should have the following characteristics; a. to be able to drive less cohesive soil b. to make no change to the ground water table level c. to make it possible to let people work in normal air pressure d. to cause less settlement at the surface To meet the above conditions various kinds of mechanical shields have been are tried, viz. limited air pressure type, rotary cutter with slit regulator, screw-discharge type, blind shield, etc. As far as the author knows, however, they are not 100% successful. Tunnels need their own accuracy in accordance to the usage. Both ease of driving

Jan 1, 1976

By Hagan T. O

The problem of rockbursts presents a serious threat to many deep, hard-rock mines. For several decades, the owners and managers of affected mines have been concious of the urgent need to control rockbursts but, to a large extent, their efforts have been hampered by a lack of fundamental knowledge. This paper will attempt to outline the extent and depth of present understanding of the phenomenon and to show how better control may be achieved in the future. It is suggested that it is helpful to distinguish two aspects of the problem: that pertaining to the mechanism of the seismic event and that associated with the mechanism of damage. Understanding damage mechanism will enable development of better support techniques while proper understanding of the source mechanism could lead to better mine planning and improved stoping layouts. In this regard, the practice of partial extraction with systematic strike stabilising pillars is discussed in some detail.

Jan 1, 1986

Geological information plays a significant, cost effective role, in the Mt Whaleback iron ore mining operations. The geology and structure are complex. Good communication between the Mine Planning Production Scheduling and Quality Control Sections is the key to utilisation of geological information to its full potential.Drilling and pit face mapping are the two basic sources of detailed data sets which are processed to prepare up to date geological cross sections and benchwise geological plans. This information is used directly for the blast pattern design and production scheduling. Physical ore type estimation is also undertaken. Orebody models are generated from the geological information.

Jan 1, 1990

By Zeni J. T

Gold was mined from quartz bodies at Ballarat East from the 1850s until closure of the last mine in 1917. The average depth of mines was about 350 m.Ballarat Goldfields Limited (BGL) carried out diamond drilling from surface between 1985 and 1987 which proved the continuation of gold-quartz mineralisation beneath the old mines.During 1989 an underground development program was commenced to access the mineralisation for detailed exploration. The program included two simultaneous shaft developments. These were known as B2 shaft and Llanberris No.1 shaft.

Jan 1, 1992

By Schofield D, Denby B, Stout F, Moli A

This paper documents the development of a user-friendly computational program, which has been constructed to assist the mine ventilation engineer in the optimal design and operation of methane drainage ranges. In the past, many computer tools for ventilation engineers led to the development of `research systems'. These computer systems, although developed with the needs of the industry in mind were due to a combination of inexperienced programming methods and the availability of suitable user interface software not easily accessible to the practising engineer. Recent developments in computer hardware and software (particularly windows based graphical user interfaces) mean that engineers no longer need to dedicate large amounts of valuable time to become familiar with often complex items of software. The authors of this paper intend to demonstrate a practical system which successfully integrates complex mathematical models, an easy to use interface and knowledge based techniques. The graphical interface guides the user to draw on the screen a mimic diagram representation of the methane drainage network. The user is prompted, during the construction of the drawing, to input the information and data required by the calculation and knowledge based procedures. The computer program then calculates all of the flows, purities and pressures throughout the network. Given reliable measured data from an existing range a comparative analysis can be performed between the predicted and measured network flow data. A knowledge-based system may utilise this analysis to either update the operational status of the network or suggest either a reasoned maintenance or remedial strategy to improve the performance of the drainage system. The development of the OMEN project has been carried out at the request of the Midlands Group, British Coal Corporation, Edwinstowe. The system is about to be field tested at a number of mines. It is hoped that when this paper is presented that the system will be used at both Group and mine level.

Jan 1, 1995

Three separate and unconfined aquifers occur in the Hilton area, named relative to position in relation to ore horizons: Footwall Aquifer in the east; Ore-Zone Aquifer within the ore-bearing Urquhart Shales; and the Hangingwall Aquifer in the west.It is the on-going strategy it Hilton to drain the Ore-Zone Aquifer which occupies structurally- and sulphide-controlled leached zones in the steeply west dipping strata. The aquifer affects considerable ore reserves to 480 m below the surface. Dewatering began in 1976, and is essentially completed to 4 level (240 m below surface). Dewatering efforts are now based on 8 level (480 m below surface).

Jan 1, 1993

By Prakash AJ, Singh PK, Dhar BB

Safety and stability of underground mine openings, coal pillars and water dams in the near vicinity of operating surface mines are endangered from excessive blast induced vibrations. This paper deals with the investigations carried out in four coal mines. Simultaneous measurements at equal distances from the source indicated higher level of vibration on the surface than those produced in the underground workings. The values of peak particle velocity (PPV) measured on coal pillars, body of water dam were lower than those measured on roof and junctions of the roadways. The parting of coal (3-4.5 m) between two sections vibrated with higher PPV compared to the roof of top section and floor of bottom section. In one case the influence of total charge fired in a round was significant in generation of vibration compared to the maximum charge/delay where monitoring was done vertically below the source.

Jan 1, 1995

By Ramani R. V

There are many important physical phenomena in mine ventilation which involve transient mass and heat transfer processes. These processes have been modeled using differential equations often solved with close form solution. Within the last two decades, many numerical schemes have been devised to solve these mass-transfer problems. Much of this effort has focused on variants of the finite element and finite difference methods. In this paper, the solution of mass transfer models in mine ventilation by finite difference technique is discussed. Specifically, the computational effort and the accuracy of the solution are presented.

Jan 1, 1988

By Bassett N

The Eneabba deposit, located 280 km north of Perth, Western Australia, and 30 km inland (Fig. 1) is one of the most recently developed deposits of mineral sands in the world. The area has been in production since 1974, while the Associated Minerals Consolidated Limited (AMA) operation commenced production in 1976. Total ore reserves of close to 400 million tonnes contain about 40 million tonnes of heavy minerals (proved and probable).

Jan 1, 1979

The scarcity of truck tyres combined with decreases in the availability of labour, increases in fuel costs and a buoyant international economy driving project budget blowouts, have all combined to change the paradigm behind mining equipment selections. The escalation of commodity prices has occurred in parallel with an increasing maturity in continuous mining machinery, mobile in-pit crushing systems and very large-scale conveyor belt systems. This paper will consider the merits of operating continuous materials handling systems, mobile in-pit crushing systems, relocatable crushing systems, relocatable conveyor systems and automated waste handling systems in place of the more conventional approach of truck haulage.

Jan 1, 2007

By Kuwasaki N, Mitsune Y

Many activity measurements of components in liquid oxides have been reported in the field of slag chemistry. However, very little is known about the thermodynamic behavior of compo- nents in oxide solid solutions. In the present paper, e.m.fs. of the follow- ing galvanic cells employing solid electrolyte Zr02(CaO) were measured on the entire range of composition of the solid solutions. Pt/Ni-(Mgl-x ix)O/ZrO2(CaO)/Ni-NiO/Pt Pt/Ni-(Mgl-xNix)2SiO./ZrO2(CaO)/Ni-NiO/Pt Pt/Ni-(Mg l-xNix)Si03/ZrO2(CaO)/Ni-NiO/Pt. Activities of NiO in these solid solutions of (Mgl_ Nix)O and (Mgl_ Nix) 2Si0a(where 0

Jan 1, 1980