Search Documents

By S Jahanshahi

In an earlier LCA study, the authors showed that the electricity consumption of the electric furnaces used in the production of the ferronickel and ferrochrome feedstocks made significant contributions towards the Gross Energy Requirement (GER) of stainless steel production, on a æcradle-to-gateÆ basis. Given the relatively low efficiencies associated with electrical power generation, substantial reductions in the GER for stainless steel production could be anticipated if more direct use of thermal energy was made in the ferronickel and ferrochromium smelting stages.In view of these findings, a follow-up study was undertaken to investigate the likely environmental benefits of using bath smelting processes for the production of ferronickel and ferrochromium compared to the traditional rotary kiln-electric furnace processes, but still utilising the electric furnace process for stainless steel production. The METSIM process simulation software package was used to set up models of the two bath smelting processes and provide process energy requirements that were incorporated into the LCA. The environmental impacts considered in the LCA were greenhouse (Global Warming Potential, GWP) and acid rain gas (Acidification Potential, AP) emissions and solid waste emissions.The results of the study showed that the bath smelting route reduced the GER for ferronickel production by about 37 per cent over the traditional route, which translated to about a 21 per cent reduction in the GER for stainless steel. The corresponding reduction for ferrochromium was about half that for ferronickel, and when combined with the ferronickel result gave a 25 per cent reduction in the GER for stainless steel production. Similar reductions were also observed for the GWP and to a lesser extent the AP for both feedstocks, as all primary energy inputs were essentially fossil fuel based. Substantial reductions in solid waste emissions were also indicated for the direct use of ores in smelting. By utilising bath smelting processes for the production of the ferronickel and ferrochromium feedstocks, stainless steelÆs suitability for meeting many of the goals necessary for sustainable development, already recognised because of its particular properties, would be even further enhanced.

Jan 1, 2004

By A D. Campbell

The Homer Tunnel is located in a remote area of the South Island of New Zealand and carries large numbers of tourists to Milford Sound through an avalanche prone area. The tunnel is 1280 m long with a steep ten per cent unidirectional grade descending to the west. Construction of the tunnel began in the 1930s and was completed to a nominal 6 m width in 1954. In 1996, two passing bays were stripped-out to accommodate bi-directional flow of tourist coaches. During all phases of construction and widening there have been episodes of strain bursting.The condition of the tunnel and standard of internal services is below current international practice, principally in terms of; in-tunnel air quality, fire life safety, ground support, and road safety. A number of near-miss events have occurred involving coach fires on the approaches and inside the tunnel. The national road authority, NZTA, is considering a substantial investment to improve amenity and safety of the tunnel.This paper describes the rationale for the proposed upgrade works and the investigations undertaken to enable that design. A holistic approach to road tunnel safety has been adopted that balances the key interrelated safety drivers, namely; tunnel lining, traffic operations, ventilation, power supply and egress while ensuring continuity of safe access to Milford Sound.

Mar 8, 2011

By Hoffmann CF

Thermal conditions at depths of several k.i'-.r.,etres in hydrothermal systems are a major (actor controlling gold transport into the epithermal environment. Understanding of the coupling of thermal, metal and ligand (HZZ S) sources in the root zones of hydrothermal systems therefore becomes important for the application of tectonic and igneous petrochem- ical studies to regional scale precious metal exploration. The evaluation of favourable conditions in this source zone and application to explor- ation rests on a detailed knowledge of the gases, H2S, CO2 hydrocarbons and other trace components preserved in fluid inclusions. Recent developments in analytical techniques now permit examination of these components and the recognition of complex hydrocarbons in rluid inclusions from epithermal and other lydrothermal systems appears promising for ieoosit-source correlation.

Jan 1, 1987

To help meet the challenge of mine finding at the start of the 21st century, the exploration geophysicist will have at his command a powerful range of tools, some new, some improved, and some which already exist today but are as yet little used. Remote sensing, using satellite and aircraft-based multi-spectral scanners, will provide the means for routinely mapping the surface distribution of certain carbonate rocks, clay and ferrous alteration minerals, based on the analysis of solar reflectance spectra. Time and emission-spectral resolved laser-induced fluorescence will likewise map the distribution of certain ore and pathfinder minerals, as well as certain skarn zones, all potentially related to ore deposits. The GPS (Global Positioning System), based on 18 orbitting satellites, will provide a universal, three dimensional, all weather navigation system which will completely supplant all existing aerial navigation systems, and greatly facilitate aerial surveying and automated processing and presentation of the data. Aeromagnetic gradiometer measurements will provide higher geometric resolution which will yield better definition of individual geological units. Multi-method ground geophysical surveys will be greatly expedited through the use of portable microcomputer-based, multi-sensor instruments. These instruments will interface with other intelligent devices for automated processing, presentation and interpretation of the ground field data. Borehole geophysics will come into more general use, both for at-hole measurements, especially using active nuclear techniques for grade determination, and for remote detection using a variety of electrical, magnetic, seismic and other methods.

Jan 1, 1986

By R Razanatsimba, A Galli

A mining company has entered into contractual commitments to supply certain quantities of its product to clients in each time period. Failure to fulfil its obligations would damage its reputation as a reliable supplier. The planned production would normally be sufficient unless major problems such as highwall failures, roof falls, natural disaster, or strikes that interrupt production or delays in obtaining environmental permits, occur. To overcome these difficulties, the company may be able to obtain more of the commodity: from its strategic stockpile (if there is sufficient there); by buying it on the spot market; or for some commodities such as gold and uranium, by leasing it. Two sources of uncertainty, the spot price of the commodity and the occurrence of serious incidents that interrupt production, are considered. For simplicity it is assumed that the commodity price follows a geometric Brownian motion, that productions incidents have a binomial distribution, that they are independent from one time period to another and that they do not affect prices. A branching tree structure is used to model the joint evolution of prices and production incidents. The aim of this research project was to evaluate the companyÆs options for fulfilling its contractual commitments. When evaluating these options, multi-stage stochastic programming with recourse was used to solve this problem because in addition to providing the dollar value of the project, it gives decision-makers the æroadmapÆ to reach the optimal value. That is, how much material should be bought/sold on the spot market, how much to add to/subtract from the stockpile, how much to lease and in the worst case what the shortfall would be, for each time period as a function of the current spot price and breakdown status. A case-study over a five-year period is used to illustrate the proposed procedure. In this study the production would be sufficient to cover the companyÆs contractual commitments unless production incidents occur. Focus is on evaluating the impact of the quantity initially in the stockpile on the value of the project when the commodity market is tight, that is, when only small quantities can be bought on the spot market or by leasing.

Sep 26, 2011

By Short KC

The Hunter Region, with a major part of the coal resources of New South Wales and a long history of coal mining, has experienced a rapid expansion of coal resource development in recent years. While there are inevitable conflicts between mining, urban development and related infrastructure, and between mining and other resources, the application of sound planning practices, and improved co-operation and co-ordination among the various parties, helps to reduce such conflicts. The planning process involves consideration of factors such as transport- ation (including port facilities), mine subsidence, provision for surface facilities, a,iC the need for buffer 'ones. In addition, provision must be made for urban expansion, often co-existing or in close proximity to present or future coal mining development. Approval of coal mining developments takes place within the legislative framework of the Environmental Planning and Assessment Act, 1979 (EPA Act), the Coal Mining Act, 1973 (CM Act) and the Mining Act, 1973. Considerable effort has gone into stream- lining and co-ordinating the procedures under these Acts. The EPA Act provides for regional and local environmental plans, as well as a linked process of development control and environmental impact assessment. The CM Act provides for the grant of exploration and coal mining titles and mechanisms for the responsible management of Mining.

Jan 1, 1987

By C R. Fountain, W R. Cannings

The zinc-lead-silver mineral resource at Lady Loretta ranks amongst the worldÆs richest when measured in terms of in situ metal grades. However, the project remains undeveloped 28 years after its discovery in 1969. The primary obstacle to development has been the fine and complex grain structure of its ores, which make flotation concentration inefficient even with fine grinding. The size and remote location of the deposit have also hindered exploitation. BUKA planned to directly fume the volatile target metals from the ore when it acquired the project. Intensive, post-acquisition modeling showed the innovative processing route to be uneconomic, notwithstanding high metals recovery and low waste content in fume product. Progressive modifications and supplements to the underlying fuming process enhanced economics and resulted in a new mine-to-metal processing route for zinc-lead-silver ores. The proprietary, three-stage BUKA Zinc Process offers technical, economic and environmental advantages. It is expected to find widespread application in the treatment of ores and residues. However, neither continued R&D nor application to Lady LorettaÆs currently delineated resource can be justified under prevailing market conditions. The objectives and results of each step in the process development sequence are outlined with reference to their impact on the commercial viability of the Lady Loretta project.

Jan 1, 1998

Spatial continuity as described by a variogram is a reflection of the underlying mineralisation/geology. Modelling of the spatial continuity (variogram) must account for both the quantitative data (ie sample grades), on which the variogram calculations are based, and the qualitative information as provided by the geological interpretation. An understanding of the geology and the variogram interpretation tie together the sample values and allow us to go beyond the actual data (Journel, 1995). Variography makes geology transportable and allows the geological interpolations to be channelled downstream into mine planning, ultimately affecting the economic decisions surrounding a deposit. As such the process of variography and resource modelling is critical. Thus consistent expert decisions need to be made which force geologists to have a closer look at the available information and the geological interpretations. The aim of this paper is to provide an overview of the latest developments in visualising variography and to demonstrate their usefulness in decisions regarding the spatial continuity of mineralisation. New ideas concerning potential future developments in visualising and modelling spatial continuity through variography are introduced.

Jan 1, 1996

This paper describes a mine truck hauling process called "Truck Jigging" which is currently the subject of a process patent application.The investigation explores the production and cost advantages of using the potential energy available in a descending haul truck to assist in elevating an ascending vehicle. Applications are studied for both strip cut mines and open pit operations. Various mechanical connections between the two vehicles are considered, based on a pulley mounted rope system. Fifteen year operating cost estimates show savings of up to 26.5 percent over conventional mine truck operations.

Jan 1, 1989

Prior to 1972, Peko Mines Limited at Tennant Creek used a central mill at Peko, which consisted of a gravity circuit, flotation and cyanidation of tailings, to treat their gold ore from surrounding mines. The Warrego concentrator, 60km to the west, was built to handle the Warrego and Gecko copper orebodies, which were being developed concurrently with the concentrator construction The Warrego concentrator consisted of a flotation circuit, using autogenous grinding at 100 - 120 tph, compared to the more elaborate Peko circuit employing rod mill - ball mill grinding capable of treating only 18 - 26 tph. During development of the Warrego copper mine a gold rich ore pod was located, because of which the mining plans were adjusted to allow simultaneous, separate extraction of the copper and gold ores. However, the plans for the concentrator were not affected as the gold ore could be carted 60km to the Peko central mill for processing.

Jan 1, 1978

By J Rubio

This work presents design features of an innovative in-line mixing helical (coiled) reactor for flocculation and flotation as a solid-liquid separation process for suspended particles (including liquid droplets). The device has been named flocs generator reactor (FGR), a compact system whereby the flocculation of particles is assisted by the kinetic energy transfer from the hydraulic flow through the reactor and/or by the injection of microbubbles (30 - 70 ¦m). The flow mixing presented a plug flow regime with a low dispersion degree, promoting the required hydrodynamic conditions to disperse the polymer flocculant (cationic polyacrylamide) and to generate æstrongÆ flocs of Fe(OH)3 or clays (as colloidal model systems) with aggregation using an anionic polymer, Al2(SO4)3 and poly aluminium chloride (PAC), and oil emulsions destabilisation with a high molecular weight cationic polymer. The solid-liquid separation of the flocs was then achieved either by settling or by flotation with microbubbles. This paper discusses advances in this new in-line flocculation-rapid flotation device to remove æaerated aggregatesÆ, aggregates with entrained and entrapped bubbles. Studies were carried out with different models of FGRs (varying the length:volume ratio) and process efficiency (mainly kinetics) evaluated as a function of polymer concentration and some operating parameters, namely, feed flow-rate, air:solids ratio and residence time. Results showed that the aerated flocs are readily floated with rising rates in the order of 120 mh-1, values higher than those obtained for the settling of the non-aerated flocs (18 - 24 mh-1). The FGR requires short residence times and generates dense, well structured flocs (with a mass fractal dimension, dF of about three) which withstand high shear forces. Mechanisms involved appear to include small bubble formation and their rapid occlusion (entrapment) within flocs, nucleation of bubbles at floc/water interfaces, polymer coiling as a result of æsalting outÆ effects at the aqueous/air interface and plug flow type of mixing (flocculation). Successful examples of emulsified oil and solids removal from water are shown and because in all cases high efficiencies were obtained (>90 per cent removal). Due to the high process efficiency and high loading capacity shown, the FGR appears to have good potential as an in-line flotation-separator device in applications requiring high rate solid-liquid or liquid-liquid separations.

Jan 1, 2005

By Marshall K. I

THE problem of satisfactorily eliminating the fumes and dust which are unavoidably produced in various metallurgical and manufacturing industries is one which has received considerable attention in the past, and has been the subject of much investigation and research. The solution of this problem was urgently desired for two reasons, the principal one being the fact that a considerable percentage of the total process losses in many industries was represented by the commercial values of the fumes and dust that escaped from the stack.The other reason is that, in some instances, the emission of the matter is regarded as objectionable. Various methods have been designed with a view to solving the problem thus presented, and the latest development that has beendesigned is the process of electrostatic precipitation. Continued investigational and developmental work with this process has already demonstrated its applicability to many industries, and new uses to which the process can be put are being opened up. Its use is already widespread, and the economic success that has attended its application in most instances would indicate that its use will become more general in the future.It has proved its ability to treat gases over wide ranges of temperature, and has successfully handled various types of fumes whose chemical characteristics differ very considerably. In many processes it has now come to be regarded as standard equipment.HISTORY OF ELECTRICAL PRECIPITATIONThe first recorded observations on the influence of an electrified insulated wire on gases containing solid particles in suspension was made as early as 1824 by Hohlfeld, in Leipzig. He found that, if he electrified a wire hung in a bottle filled with smoke, the smoke cleared rapidly, and a deposit formed on the sides and bottom of the bottle.

Jan 1, 1923

By F P. van der Meer, E Lessing, E Matthies

High pressure grinding rolls (HPGR) technology is growing to be a common comminution tool in iron ore processing. The technology finds a wide acceptance and presents specific benefits in coarse ore grinding and closed-circuit grinding in preparation of ball mill feed, right down to the other end of the particle size spectrum for iron ore pellet feed preparation.A growing number of minerals processing plants are facing higher operating costs and difficulties due to a scarcity of process water, which in some cases is a result of more stringent environmental constraints. In addition, many new iron ore deposits are located in more arid regions of the world. These challenges have led to operators taking a new look at dry processing of iron ores.The use of dry crushing and classification technology in cement production from blast furnace slag, clinker material or limestone feed stocks indicates that the technology may be applied in minerals processing. In addition, dry processing provides the possibility of generating a final product from finely disseminated and inter-grown ores at sizes near or well below 100 µm, as may be required for beneficiation techniques such as in fine magnetic separation, flotation or magnetic flocculation.Dry grinding by HPGR has a number of specific features, challenges and opportunities, including balancing power input, moisture content requirements and classification efficiency in the process design. HPGR parameters and the latest HPGR design and sizing capabilities indicate considerable potential benefits from this dry processing technology.This paper highlights some of the specific issues that play a role in dry HPGR application, with respect to energy and materials balances. Examples of dry HPGR practices and process studies in iron ore mineral processing are discussed.CITATION:van der Meer, F P, Lessing, E and Matthies, E, 2015. Iron ore final grinding by high pressure grinding rolls and air classification, in Proceedings Iron Ore 2015, pp 197–204 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By T Horberry

This paper describes work conducted as part of an overall research project that aims to identify current and emerging trends in the development of automation and remote mining technologies, and to provide an operator-centred perspective to the design and deployment of such systems. More specifically, this paper outlines a research and development process being constructed to examine the issues of the human skills and capabilities required to operate or maintain automated/remote controlled mobile mining equipment. A human factors approach presented here, where the focus is upon designing equipment interfaces to fit operators, rather than purely designing and deploying the equipment based on a technology-centred approach. However, the importance of training to help develop the required skills and capabilities is also emphasised.The work built on a full review of the literature about the effects of automation in mining and elsewhere, extensive interviews with different stakeholders in mining automation and recognised best practice regarding designing for the human element in automated systems. The human element research and development process proposed is in four stages, ranging from understanding the tasks involved in both manual and automated equipment operation through to user trials to ensure that the automated systems are acceptable to operators and are fit for purpose.It is outside the scope of the current paper to present the full data collection described by this four stage process, but an overview of what will be collected is presented. As such, this paper focuses on the broad methods being developed, rather than the specific results to be obtained. The ultimate objective is to apply a broad ‘technology assessment’ approach to the design, deployment and evaluation of automated mining technologies, in particular by considering the user-centred design implications of these technologies.

Nov 22, 2011

By S Hapugoda, J R. Manuel, M P. Ma, L Lu

Iron ore sinter quality depends heavily on the mineralogy, textures and physical structure of the sinter, which is formed upon solidification of the primary sinter melt. The interactions of the initial sinter melt with its surrounding materials will impact on the properties of the primary sinter melt and consequently the solidified structure of the sinter. By using a high-temperature visualisation system, in situ studies have been conducted on the effects of melt compositions (Al2O3, SiO2 and MgO) on the interfacial phenomena of the sinter melt on a natural iron ore substrate. It was found that the melt composition significantly influenced the wettability between the sinter melt and the iron ore substrate. The interactions between the sinter melt and the natural iron ore substrate were also examined. Such interactions can lead to further changes of sinter melt composition and hence the sinter melt properties that, in turn, further affect the wetting behaviour of the sinter melt.CITATION:Ma, M P, Lu, L, Hapugoda, S and Manuel, J R, 2013. Effects of melt composition on the interactions of sinter melt on a natural iron ore substrate, in Proceedings Iron Ore 2013 , pp 431-440 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

Froth flotation is widely used for the separation of particulate materials in the world. It is a complex process whose operational behaviour in process plants is difficult to predict. A comprehensive phenomenological dynamic flotation model was presented at the 1982 IMPC. This model uniquely linked the particle/bubble interactions and water transport phenomena to the flotation cell hydrodynamics. The model was used as a dynamic framework to analyse and develop process optimisation strategies. New developments in mineralogical characterisation, real time information management systems and data validation simplify the implementation of flotation technologies for mine to mill grade recovery optimisation. With recent developments in software programming, dynamic simulation enables process engineers to develop process alternatives interactively. This paper presents such an implementation of current process analysis tools and an updated froth flotation dynamic model. It demonstrates how this new environment can be used to improve our technological knowledge of flotation, eg alternative bubble/particle attachment and detachment microprocesses can be incorporated. The dynamic flotation model has several manipulated variables (such as feed flow rate, per cent solids, aeration, wash water flow rate, frother flow rate, specific power energy (impeller speed/delta pressure), cell geometry and tails flow rate) and evaluates the dynamic effects of these variables on grade and recovery.

Jan 1, 2005

By R Justa Cámara, L M. Pinillos Lorenzana

Barcelona Metro Line 9 (Line 9) is an essential infrastructure, improving the transversal transport in Barcelona by connecting the greater part of the currently existing radial lines. The purpose of Line 9 is to create a peripheral line surrounding the city of 1.6 million people (metropolitan area exceeds five million), and includes 52 stations, of which a total of 32 are deep shafts and 19 transfer stations in a densely populated area with several geographical constraints.The tunnel has an inner diameter of 10.90 m, bored with an earth pressure balance (EPB) tunnel boring machine (TBM) in soil sections with precast concrete lining type universal ring and segments 40 cm thick.A single tunnel solution was adopted, driven by functionality and costs savings. The internal tunnel section is divided into two levels to allow for one way rail transit including the platforms in each station on each level in order to optimise the space created by the TBM excavation and comply with the operational needs. The division in two areas of the tunnel was carried out through the construction of a horizontal slab resting on the tunnel segments with a constant thickness of 40 cm at the central part of the slab and supporting side walls.CITATION:Justa Cámara, R and Pinillos Lorenzana, L M, 2014. Two transit levels in one tunnel tube – an innovation in Barcelona Metro Line 9, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 387–398 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

Production from a major, deep orebody requires the construction of two 6 m diameter, 1000 m deep ventilation shafts over the next three years. Further ventilation upgrades have foreshadowed an additional 1500 m of 6 m diameter shafts beyond that. After reviewing the construction alternatives it was decided to raisebore the first shaft in one pass using Western Mining Corporation's 121R raiseborer and the Wirth sequential head. The significant cost and speed of construction potential of 6 m raiseboring justified the risks associated with this new technology. Large diameter sequential head raiseboring has only been carried out in South Africa. Over the last three years many lessons have been learnt and the technology has progressed to being considered feasible. Operating practice and the optimisation of raiseboring performance for specific ground conditions are the areas requiring further work. The development of large diameter raiseboring in South Africa and the site preparation and initial operation at Z.C. Mines are described. Comment on actual operating experience includes the geotechnical investigations, the raiseborer foundations, cuttings disposal and the drilling of the pilot hole which has progressed to beyond 450 m. Unforeseen difficulties with the verticality of the pilot hole and with mud losses illustrate the types of problems that can be expected.

Jan 1, 1988

By S Bourke, R Stone, B Hill

Since Jameson Cell flotation technology was first installed in a coal flotation application in 1988/89 at Newlands Coal Handling and Preparation Plant (CHPP) there have been fundamental improvements to its design which has led to its current status as the leading technology in Australia for fine coal flotation. These improvements, which include key hardware modifications, consist of the re-development of the orifice plate to produce considerable increase in wear life and reduction in power consumption for a given air entrainment and a significant increase in the amount of air that is entrained. Modifications to the downcomer allow maximisation of residence time and air entrainment while changes to the feed and air distribution system allows a reduction in installation cost and a reduction of solids ingress into the air line. Additionally, operational improvements such as the use of recycle to maintain constant flow to the cell feed are discussed. The recent installation at Hail Creek in the Bowen Basin, which consists of three B6000/20 Jameson Cells (6 m diameter bottom-fed distributor with 20 downcomers) will be reviewed as a case study. The latest design and operability of the cells are summarised and compared against one of the original designs at Riverside CHPP also in the Bowen Basin.

Jan 1, 2005

By Hebbard GJ

Vertical crater retreat mining is being used at Zinc Corporation, Limited and New Broken Hill Consolidated, Limited for pillar recovery between previously mined and filled stopes. In order to increase productivity in the older lead lode areas of the mine, particularly in the lower grade sections around the keel of the orebody, score form of longhole stoping was considered necessary.Due to poor ground conditions in the country rock surrounding the ore and the requirement to provide sane wall support during mining, primary VCR mining has been utilised in these areas.At Zinc Corporation, several stopes have thus far been mined by a hybrid longhole stripping - VCR method.

Jan 1, 1985