Search Documents

"Quiet, please!" is the newest directive being thrust at industry by guardians of the environment-with good reason. In countless cases, industrial noise is literally deafening its listeners, and sooner or later the volume must be turned down. Noise control is already mandatory for many companies under a Federal regulation that went on the books when the Walsh-Healey Act was revised last May 20. The new rules impose specific noise limits on any plants supplying the Government with goods under a contract valued at more than $10,000.

Jan 1, 1970

By A. C. Bluemel, J. S. Harper, J. H. Jett

Can the mining industry in the United States accept the change and challenge of the "Now Generation" of an entirely new high-performance automated transportation system? Advanced transportation systems for the mining industry can be defined as those which lend themselves to automation and meet definite performance and cost objectives. The term automation shall mean that control of transportation system is accomplished by a closed loop electronic circuit which, when started on command, will continue to cycle as programmed until such time as an intelligent feed-back causes the system to shut down.

Jan 1, 1970

By Richard W. Greene, Joel S. Hirschhorn

MATERIALS containing very large amounts of porosity, in the order of 50 to 90 vol pct, are extremely difficult to evaluate according to conventional mechanical behavior tests. This is usually a consequence of their low strength and brittleness, and the difficulty of preparing standard test specimens. A simple fatigue test has been developed and used successfully on porous nickel sheet materials requiring no specimen preparation; it could also be used for configurations other than sheet or plate. Samples of the sheet. 2 in. sq and about 0.025 in. thick, are placed in a vessel that is evacuated to about 50 f Hg by a mechanical pump. Distilled and deairated water is allowed to enter the vessel thereby filling the porosity (virtually all the porosity in these nickel ma-

Jan 1, 1970

By E. E. Wark, J. Rogers, I. W. Wark, K. L. Sutherland

SOAPS have been used as collectors for many years, but only in the last eight years have other long-chain paraffin salts been used. It may be anticipated that these newer collectors will be used mainly with nonsulphide minerals, for which the xanthates and similar compounds are of little value. On the other hand, the xanthates are both cheap and effective for sulphide ores and seem likely to retain their present eminence in this field. During 1938 and 1939 two of us (E. E. W. and I. W. W.) commenced a comprehensive investigation of the principles underlying the use of paraffin chain salts as flotation reagents. This research was sponsored jointly by the University of Melbourne and a group of Australian mining companies.[t] A broad, semi quantitative survey was then made of the field covered in the present paper. This was followed in 1940 by further work by one of us (K. L. S.). In 1941 the investigation was taken over by the Division of Industrial Chemistry of the Commonwealth Council for Scientific and Industrial Research, Australia. Discovery of some principles upon which are based the flotation of minerals by paraffin chain salts was followed by their application in the development of processes for the recovery of certain strategic minerals from their ores. Promising results in the flotation of cassiterite from various ores will be described in a subsequent paper. THE PARAFFIN CHAIN SALTS The basic requirements for a "collector" in flotation are that it should form a film over the surface of the mineral to be floated, and that this film should be orientated so that hydrocarbon (nonpolar) groups form the effective surface. When modified in this way, the mineral surface possesses some degree of air avidity. All investigators would agree with Taggart, Taylor and Ince23 that such a film can be produced only if the collector compound contains an active (polar) group to attract it to the mineral surface as well as the nonpolar group. One section of this large class of polarnonpolar compounds is the paraffin chain salts: CH3(CH2) „X where X signifies a polar group that ionizes in aqueous solution. Though the compound can ionize, it may be a weak or a strong electrolyte, and the hydrocarbon chain may be in the cation or the anion (Table I). Many compounds of similar constitution are available, but the usual polar groups are: -CO2Na, -SO3Na, -SO4Na, - PO4Na2, or an aminonitrogen group, the

Jan 1, 1946

By J. R. Ross, J. B. Rosenbaum

Bureau of Mines research has resulted in the development of fluid- bed ion-exchange columns for recovering uranium from slime pulps. In pilot plant tests, slime slurries containing up to 6 percent solids were processed at flow rates of 10 gallons per square foot per minute with high uranium recoveries and efficient resin loadings. Uranium was effectively eluted in a laboratory fluid-bed elution column at eluate-to-resin ratios of less than 5:1 and eluate flow rates of 3 gallons per square foot per minute. Construction costs of mills using these improved ion exchange techniques are estimated to be 25 percent less than for mills using solvent extraction of clear solutions. For mills having a capacity of 2,000 to 2,500 tons of ore per day, the saving would be in the range of $2.5 million. In addition, a saving of about $0.80 per ton of ore in total operating costs is indicated.

Jan 1, 1973

By R. W. Callen, W. A. Hockings

This paper describes a computer program which calculates material balances for complex steady-state material flow circuits encountered in mineral processing. The program determines mass flows in the various process streams of a flowsheet from multicomponent analytical data obtained from samples of the streams. The program, Metallurgical Balance System (MBS), has been used extensively in treating Pilot plant test data, in production evaluation and control, and in plant design. The program performs well even on ill-conditioned data. Input to the program is easily accomplished by unskilled personnel and the output appears in well-formatted tables.

Jan 1, 1981

By W. Scott Dunbar

INTRODUCTION Methods of linking boundary integral (BI) solutions with finite element (FE) solutions have been well described theoretically in other publications (e.g., Zienkiewicz, et al., 1977). The purpose of this paper is to point out some practical aspects of implementing these linkage algorithms for rock mechanics applications and to describe an alternative linkage algorithm. A not so obvious motivation for using FE-BI linkages is illustrated in Figure 1. The cost of modeling the excavation of the crusher station by the BI method can equal or exceed the cost of an equivalent FE model. This is due to the large surface area which must be modeled by the BI method. In such cases, a more economical approach might be to model the region immediately adjacent to the crusher station by finite elements and link the solution at the periphery of the FE model with a solution for the exterior region. Further economies can be realized if some flexibility in the type of exterior solution is possible. For example, it would be desirable to use a coarse discretization of the FE-BI interface for a BI solution, which would be less demanding of computer storage and time, or to use an analytical solution for the exterior region. The alternative linkage algorithm to be discussed allows such flexibility. BOUNDARY INTEGRAL METHODS There are basically two formulations of BI methods: the direct and the indirect. FE-BI linkage algorithms depend on which formulation is used. The purpose of this section is to briefly describe each method.

Jan 1, 1982

By R. S. Dean

THE commercial production of electrolytic manganese on a small scale commenced in 1939. The writer made a short report on the progress of production and utilization in MINING AND METALLURGY for January 1941. Progress during the last two years, naturally, has been more rapid. In June 1940, Congressman (now Senator) Scrugham presented a proposal to Congress for an appropriation authorizing erection of a pilot plant for "the production of metallic manganese by electrolytic or other means." As a result of this, a pilot plant, having a capacity of a few hundred pounds per day was built at Boulder City, Nev. Subsequent appropriations permitted expansion of the plant to about a ton per day. Much has been learned in this plant about electrolytic manganese, and the product even in its small way has found war uses of considerable importance. Meanwhile, the Knoxville plant of the Electro Manganese Corporation, the sole commercial producer, was expanded to about 4 tons per day to supply needed material for the war program. Other proposals for commercial plants have not been favorably received by the War Production Board. The Bureau reported on one such proposal by the American Alloys and Chemical Corporation. PRACTICE AT BOULDER CITY The present practice, as carried out at Boulder City, which is being described in more detail in a current paper by the Bureau staff at Boulder City, starts with a manganese dioxide ore containing about 20 per cent manganese. Currently this ore comes from the Three Kids deposit near Las Vegas. The steps for the production of electrolytic manganese, in general, are as follows: I. The manganese in the ore is reduced to MnO. 2. The MnO is dissolved from the ore in spent electrolyte, which contains about 38 to 47 grams per liter of free sulphuric acid, 135 grams per liter of ammonium sulphate, and 10 to 12 grams per liter of Mn as sulphate. In the leaching step the manganese is built back up to 32 to 36 grams per liter of Mn as sulphate; the pH is adjusted to neutral by means of gaseous ammonia and passed through thickeners. 3. The electrolyte is purified by adding H2S, which precipitates the heavy metals. After filtering, ferrous sulphate is added to the solution and oxidized with air and the solution is filtered and clarified on a precoat filter. 4. The purified catholyte is electrolyzed in a diaphragm cell using stainless-steel cathodes and lead-silver anodes. The current density is about 45 amp. per sq. ft. Current efficiencies of 60 to 65 per cent are regularly obtained.

Jan 1, 1944

By H. H. Smith, G. J. Danek, M. R. Achter

Nickel, Type 316 stainless steel, and copper show decreases in reversed bending fatigue strength with increases in air and oxygen pressure. The leveling off of the log N us log p curve for nickel at 300" and 816°C is discussed in terms of a model in which surface saturation gives rise to a critical pressure. A metallographic study indicated that the effect of environment on crack initiation and growth rates is a function of temperature. It is shown that small amounts of impurities in inert gases may substantially reduce the fatigue strength of nickel. 1n a previous investigation1 of high-temperature bending fatigue in air and in vacuum, reversals in the effect of environment with changes in test conditions were atrributed to a mechanism consisting of two processes acting in competition. One of them, oxidation strengthening, has been demonstrated in a straightforward manner by measuring the rupture strength of a sintered nickel-oxide bond.' The detailed operation of the other process, facilitation of crack propagation by surface absorption of oxygen, is uncertain. Thompson et UZ advanced the possibility that the formation of an oxide layer prevented rewelding of cracks during the compressive part of the cycle, while Wads worth and Hutchings4 further proposed that the reaction of oxygen with atoms at the tip of the crack helped the metal to break there, a possibility which has also been advanced to explain crack formation in creep.5 A difficulty in arriving at a mechanism for this lowering of fatigue strength in air is the inconsistency of some of the data. For example, Wadsworth and Hutchings4 found an approximately linear decrease of log cycles-to-fracture (N) with an increase of log pressure-of-air (p) for copper and aluminum at room temperature, while snowden,' although finding a similar linear dependence for aluminum, observed a stepped curve for lead. Between l0-' and 10"1 torr there is a sharp decrease in the fatigue life of lead with increasing air pressure, but plateaus, signifying no dependence on pressure, are found at higher and lower pressures. If, as discussed elsewhere: these environmental effects arise from the adsorption of gas on crack surfaces, it would be expected that as the pressure is increased a saturation point would be observed, beyond which there is no further effect. To gain further information about the form of the log N vs logp curve, it was decided in the present investigation to repeat this type of measurement at elevated temperature on nickel, copper, and Type 316 stainless steel. An additional object of this program was

Jan 1, 1963

By Waldemar Dyrssen

BEFORE discussing the relation between air pre-heaters and waste-heat boilers in conjunction with the open-hearth furnace, it is necessary to have a clear idea about what a preheater can accomplish and what effect it has on the open-hearth furnace, especially from a thermal point of view. It is generally recognized now that the heating of the combustion air in the checker chambers of the open-hearth furnaces is not as efficient as it is-desirable to make it. It is also generally recognized that heating of the air in checker chambers of ordinary construction has its limitations. These limitations are mostly the .space occupied and the cost that would be involved if checker chambers were made larger than according to present practice. There are, however, other. reasons why checker chambers cannot give the highest possible air temperatures. Checker chambers are capable of heating air to very 'high temperatures by using waste gases of extremely high temperatures and, in fact, higher temperatures can be reached with checker chambers than with any other means available. The temperature to which we can heat, air, however, is limited very materially by -the temperature at which the air enters the checkers, be-cause of the fact that checker chambers, as at present constructed, are not efficient in heating air through a wide range of temperatures. In other words, if air in-stead of entering the checker chambers at atmospheric temperatures could enter at about 1000 to 1200 deg. F., the resultant air temperature at the top of the checker chambers would be materially increased. There are now on the market metallic air preheaters which are ex-tremely efficient for preheating air to about 1200 deg. F. Such heaters occupy very little space and can usually be installed at a relatively low cost.

Jan 1, 1928

By Godfrey T. Vivian

Very often important discoveries are made in one industry that may be used to advantage in another, but, owing to the rarity that men step out of one industry into another, these discoveries remain unknown outside of the trade or profession in which they are made. The present paper is written solely with the object of bringing to the notice of mining and metallurgical engineers a centrifugal ore-concentrator which eventually may have a great application. Ore- Grading. Fig. 1 represents the action which takes place when solids of different dimensions are stirred up in a box and allowed to settle as minerals of the same size but of different specific gravity. This principle is applied practically in grading china-clay and in enriching tin-slimes. In the latter case the slimes are stirred around in a tub with water and allowed to settle while at the same time the side of the tub is struck with a hammer. The colloidal slimes are then poured off and various slices taken off horizontally. The great drawback of this process is that the particles are deposited horizontally and all the colloids are lost. Fig. 2 represents the action in which the particles are deposited side by side. Here the drawback is the great length of the box needed in order to prevent excessive loss. The alternative to lengthening the box is to increase the force of gravity. Centrifugal force may be regarded practically as the force of gravity augmented. Fig. 3 illustrates the Gee centrifugal machine for grading ores. The drum, A, fitted with a box, B, is mounted on a shaft or spindle, C, the whole being suspended from a ball-bearing of special design at D, supported between girders, E. Rota-

Jan 1, 1913

By T. M. Chance

The first bituminous coal cleaning-plant to use the sand-flotation process1 was placed in operation on Oct. 1, 1925, at the tipple of the East Broad Top Railroad & Coal Co., at Mt. Union, Pa. The general principles governing the design of plants of this type and typical operating results of anthracite sand-flotation units have been previously outlined.2 I will, therefore, confine myself to a description of this particular plant and to some of the elements of design it incorporates. The Original Mt. Union Tipple The plant was installed to transfer coal.from steel narrow-gage cars of 60,000 and 70,000 lb. capacity to standard-gage equipment. The coal was hauled about 30 miles from the East Broad Top field. This coa1, mined by the Rockhill Coal & Iron Co. and other operators, is a low-volatile slow-coking coal with ash of high-fusion point. It is normally a high-grade coal that does not contain an excessive amount of free impurities, but it requires careful handling to secure a fair domestic yield, and, naturally, the need for narrow-gage transshipment increases the difficulty of the problem. The narrow-gage cars were discharged into an 8-car track hopper equipped with two feeders passing the coal to two 42-in. apron intake conveyors. Twin units were installed throughout the original plant, two lump-and-egg shaking screens, two lump picking-tables, two egg picking-tables and two stoker conveyors. The stoker coal was loaded without cleaning. The loading tracks and booms were in duplicate and, with the layout as originally installed, either unit could be run independently, each unit shipping a different class of coal or both units making the same product.

Jan 1, 1927

By D. G. Brubaker

IN the history of geophysical exploration by the electromagnetic method many procedures and types of equipment have been used. Source arrangements for surveying on the ground have included long wires grounded at both ends, large loops laid on the ground, small horizontal loops, and vertical loops of moderate to small sizes. Receivers have ranged from simple direction-finding coils to combinations of coils and a bridge circuit to measure quantities related to both amplitude and phase of the received signal. Primary considerations in choosing a survey method are effectiveness, speed, and economy. In work on the ground in which locating and out- lining conducting bodies is the objective, methods using a vertical coil and a simple direction-finder have been found the most satisfactory. Mason1 and his associates applied such a method by setting up a vertical source loop, fed with low frequency alternating current by an engine-generator set. With a direction-finding receiver they surveyed lines along the ground in the plane of the loop, taking measurements at each station of the azimuth and inclination of the magnetic field direction. Deviations of this direction from the normal direction, that is, from horizontal and perpendicular to the traverse line, indicated a conducting body. Recent advances in design of light-weight generating equipment have encouraged using this and similar methods.

Jan 7, 1957

By Butler, P. B.

TRIPOLI is a rather unusual form of silica, which thus far has been found in commercially valuable quantities only in the neighborhood of Seneca, Mo., although there are numerous deposits of somewhat similar materials in several southern states. The latter have not, however, attained any position of real importance, due undoubtedly to definite structural limitations which have rendered them less suitable for the particular uses that have given tripoli its principal outlets. Raymond B. Ladoo, mineral technologist, says': "Since that time (1880-90) the term tripoli has with increasing definiteness been reserved for the Seneca material, and other siliceous materials of similar origin and physical properties."

Jan 1, 1928

By G. Hasenfus, M. Karmis, G. Goodman

Surf ace subsidence is rapidly becoming an important environmental consideration of active as well as abandoned mining operations. The damages attributed to this phenomenon have been witnessed in both rural and urban areas and include land settlement and fracturing, structural damages to surface buildings or facilities and disruption or contamination of ground water supplies. The problem of mining subsidence has gained considerable emphasis in the Appalachian coalfield. The increased mining activity over the past few years and the particular topographic conditions, lithologic and structural environment, mining methods and hydrological patterns are all factors which have contributed to specific subsidence characteristics in this region. The objective of this paper is to discuss and review the most widely accepted methods of subsidence prediction above longwall as well as partial extraction systems in Appalachia. These include an accurate and easy to apply empirical method, which has been developed entirely from field information pertaining to the Appalachian coalfield and incorporates both geometrical and geological information of the panel in question. The second method is a development of influence functions and is founded on the zone area approach. Both methods, originally derived for longwall mining, have been expanded to include room and pillar applications and have been widely used by the mining industry in the Appalachian coalfield.

Jan 1, 1984

By Walter Miller

Any annual review of engineering progress in petroleum refining must of necessity include many features mentioned in earlier reviews. Advances do not spring mushroom fashion to wide acceptance overnight, but rather resemble rolling snowballs, gathering size and velocity as they progress. The new ideas of one year develop through the course of scattered adoption and testing during following years, to be ultimately discarded or to become an integral part of refinery engineering and operation. Polymerization and Cracking As an illustration, the publicity given to the polymerization and cracking of petroleum gases during the year has given many the impression that this is a new art. But patent and technical literature have disclosed active work on the problem dating back a decade or more and a unit capable of making 100 bbl. a day of polymer gasoline was constructed as early as 1930. Important strides have been made during 1935 looking to the more general commercialization of available processes, and some four important groups are furthering this work. In addition to the production of liquid products for inclusion as a constituent of commercial motor fuel, polymerization has also been a factor leading to the installation of a plant at the Houston refinery of The Shell Petroleum Corporation for manufacturing isooctane for aviation use, by making available dibutylene for catalytic hydrogenation Polymerization is not confined to unsaturated hydrocarbon gases as a source of raw material, and has been extended to include a preliminary decomposition of normal saturated gases under suitable heat and pressure conditions into the unsaturated types, which can then be used as raw material for the polymerization process. Thus there is opened up the possibility of eventually using large quantities of natural gas in the manufacture of high-grade motor fuels, although the early commercial growth will be largely on cracking still gases for economic reasons. Such utilization will result in a somewhat lowered drain on crude-oil reserves and a partial elimination of the

Jan 1, 1936

By Walter Miller

Any annual review of engineering progress in petroleum refining must of necessity include many features mentioned in earlier reviews. Advances do not spring mushroom fashion to wide acceptance overnight, but rather resemble rolling snowballs, gathering size and velocity as they progress. The new ideas of one year develop through the course of scattered adoption and testing during following years, to be ultimately discarded or to become an integral part of refinery engineering and operation. Polymerization and Cracking As an illustration, the publicity given to the polymerization and cracking of petroleum gases during the year has given many the impression that this is a new art. But patent and technical literature have disclosed active work on the problem dating back a decade or more and a unit capable of making 100 bbl. a day of polymer gasoline was constructed as early as 1930. Important strides have been made during 1935 looking to the more general commercialization of available processes, and some four important groups are furthering this work. In addition to the production of liquid products for inclusion as a constituent of commercial motor fuel, polymerization has also been a factor leading to the installation of a plant at the Houston refinery of The Shell Petroleum Corporation for manufacturing isooctane for aviation use, by making available dibutylene for catalytic hydrogenation Polymerization is not confined to unsaturated hydrocarbon gases as a source of raw material, and has been extended to include a preliminary decomposition of normal saturated gases under suitable heat and pressure conditions into the unsaturated types, which can then be used as raw material for the polymerization process. Thus there is opened up the possibility of eventually using large quantities of natural gas in the manufacture of high-grade motor fuels, although the early commercial growth will be largely on cracking still gases for economic reasons. Such utilization will result in a somewhat lowered drain on crude-oil reserves and a partial elimination of the

Jan 1, 1936

By Oswald J. Heinrich

THE great improvements which have been made in late years in the different systems and instruments used to perforate the crust of the earth for purposes of testing and exploring for mineral resources or for other reasons, by means of bore-holes of greater or less diameter and to greater or less depths, are manifold. It may therefore be of interest to make an impartial comparison of them, or of such as are most commonly used. Being well aware of the difficulties which are encountered in such a task, a reasonable allowance must be made in such a comparison. It is a rare instance when even two decidedly different systems or instruments have been used in the same locality, penetrating identically the same strata to the same depth. The diameter of a borehole as well as its greater or less depth must also be considered in regard to its cost per foot, etc. But for practical purposes, for ex¬ploration at least, we may assert this rule Any borehole, of whatever diameter, which allows the means of examining the strata most carefully and completely, will be sufficient for this purpose, but that one which will do it most economically and in the least space of time, must be considered the best for it. It will, therefore, partially depend upon circumstances, what system, in spite of other superiorities, may be the best in each case, and the following remarks may aid in deciding this question. To make the attempt here to review all that has been published upon the different systems and means of boring would be out of place. Reference can be had to the able publications treating upon this subject. A difference in this respect exists in regard to the use of the hollow rods in connection with the diamond drill, used for that purpose. The great future, which appears to be evident for this instrument, will be warrant enough for any one, who has had the opportunity to test it, to give his experience to the public. Only in this way can we bring this system to such perfection, as it seems to deserve and * The drawings illustrating this paper are one-half the size of the tools represented, with the exception of the instrument used to reverse the current in the bore-hole (Fig. 17), which is one-third the actual size.

Jan 1, 1874

Launching Platform - Drift Indicator- Stratascope-are components of Carbide and Carbon Chemicals new Mining Machine No. 3.

Jan 1, 1953

By N. R. Adsit

THE B-Ni system was chosen for this study because of the great interest being shown in boron-fiber-strengthened composite materials. Boron fibers were obtained from Texaco Experiment, Inc. They average 4.2 mils in diam with a 0.5-mil tungsten wire in the center. In order to make the diffusion couple, the fibers were included in the nickel matrix by electroforming. The samples were placed in a preheated furnace for the desired temperature and length of time. Sectioning and polishing the samples revealed concentric rings as shown in Fig. 1. The average penetration distance, X, was calculated by measuring the radius of the second phase (the white shell in Fig. 1) and subtracting the original radius. The second phase was identified as NiB by X-ray diffraction. This allows the kinetics of the formation of the phase NiB to be calculated by Eq. [I], which is taken from offman:"

Jan 1, 1967