Search Documents

By M. E. Lombardi

THE Coalinga oil field is located on the west side of the San Joaquin Valley, California. The structure is in general a monocline, the edges of the oil horizon resting on the foot hills and dipping gently toward the east. One prominent anticline occurs plunging southeast. The earlier drilling was done in the foot hills comparatively near the outcrop and the wells were shallow. The sands were followed eastward and, in the case of the anticline, along the plunge, the wells becoming deeper and deeper until the depth of 4,000 ft. was reached and passed. There is nothing to show that the oil will not be found in quantity at still greater depth. In fact, some of the best producers have tapped the sand at close to 4,000 ft. The recovery of oil still farther to the east, and therefore at greater depth, seems to be mainly a question of drilling. In this territory the formations drilled through are chiefly sands and shales; they will not "stand up" in an open drilling hole; the casing has to be carried close to the bit, and it is always difficult to keep the casing free for any considerable distance. Ability to carry casing of comparatively large diameter without conductor pipes for distances of 2,000 or 3,000 ft. or over is desirable in such territory chiefly for two reasons. It makes it possible to enter the oil sand with a pipe of ample diameter; it eliminates one or more expensive strings of casing which act only as conductors for the water string, and furthermore, in territory where waters are encountered which corrode steel rapidly, it makes possible the construction of a rust- and alkali-resisting water string. It is always desirable to shut off top waters, which may lie within 100 ft. or less of the oil sand, with 10-in. pipe. Where the depth is so great that a practical weight of 10-in. pipe will not withstand the probable collapsing pressures, 8 ¼ in. at least is desirable. About the limit of rotary drilling to date in California seems to be the setting of the 10-in. string at 3,200 ft., although the rapid advance in rotary work during the past year seems to indicate that this depth may soon be increased. It is my purpose now, however, to treat only of cable-tool drilling.

Jan 2, 1915

By M. E. Glicksman, G. S. Ansel

It has been shown by Walton and Chalmers,&apos; that the mechanism of the development of solidification textures in castings involves the preferential growth of dendrites along certain crystallographic directions as determined by the influence of prevailing heat-transfer conditions. Specifically, this growth is parallel to the direction of heat flow. The purpose of the present investigation was to determine the applicability of this mechanism to: 1) commercially pure aluminum (99.75 pct) solidified to coarse columnar crystals, 2) an aluminum-silicon casting alloy (5.25 Si, 0.38 Fe, 0.02 Cu, 0.10 Ti, 0.002 S) cast to a fine-grained structure under complex and reproducible heat transfer conditions. PROCEDURE AND RESULTS 1) Specimen Preparation—Using a technique similar to that employed by Northcott and Thomas,2 samples were melted in the directional solidification mold, Fig. 1, by heating the entire assembly to 670° C. The mold was then end cooled using a water jet. From considerations of harmonic analysis, the likely distribution of isotherm normals encountered by the growing crystals is shown in Fig. 1. 2) Orientation Analysis—The pure aluminum sample froze to large columnar crystals, nucleated close to the metal diaphragm, with the growth direction parallel to the mold axis. Using the back-reflection Laue technique, the growth direction of these crystals was determined to be a <100>, which coincided within 53 deg to the mold axis. Metallographic examination of the relatively fine-grained aluminum-silicon sample revealed a dendritic mode of growth having its primary dendrite arms along isotherm normals. Back-reflection Debye-Scherrer patterns, taken with the specimen rotating about its cylinder axis, yielded rings displaying symmetrical arcing, thus proving that the sample did, indeed, possess the solidification texture inferred from the preliminary metallographic examination. To determine the extent and orientation of the texture in the aluminum-silicon alloy, a density distribution of the (111) poles of the sample was plotted using the transmission Debge-Scherrer

Jan 1, 1960

By Daniel D. Pollock

The il&apos;lott and Jones theory of thermoelectricity predicts that the absolute thermoelectric power of alloys of transition and noble metals should be a maximum when the concentration of the noble metal is approximately 55 to 60 at. pct. An examination of the emf of a series of relatively pure alloys of copper and nickel shows that the predicted maximum occurs at about 57 at. pct Cu. This excellent agreement with the theory is considered to substantiate the Mott and Jones theory of thermoelectricity for binary alloys of transition elements. This theory is extended to show that the emf behavior of dilute, ternary copper-nickel base alloys, which contain approsimately 60 pct Cu and 40 pct Ni, may be described in terms of a scattering mechanism. The scattering effect of a third element is demonstrated to be a function of its valence and its period in the periodic table. Small amounts of solute elements have additive scattering effects upon the emf of the Cu-Ni base. The Mott and Jones equation is modified to include this scattering parameter. This adaptation accurately describes the thermoelectric behavior of ternary and quaternary CLL-Ni base alloys. An empirical form of the modified Mott and Jones equation is derived which permits the calculation of thermoelectric power with an average error of less than 0.4 pct at 500 "C. CONSTANTAN has long been used as a thermocouple element. Its approximate composition varies from 50 pct Cu, 50 pct Ni to 65 pct Cu, 35 pct Ni. Small amounts of manganese, iron, and other elements have been used to modify the composition in order that the resultant emf vs platinum conforms to nationally accepted table. Adjustments of this type are made on a purely empirical basis. Constantan was originally made in Germany and was imported into this country for thermoelectric and electrical resistance purposes. During World War I, the supply of this material became seriously depleted. The work of Bash4 was done in this period in order to develop a satisfactory substitute for the imported material. Bash&apos;s empirical work on Cu-Ni alloys is still the basis for all commercial constantans made in this country. No reexamination of the electrical properties of this system has been made, despite the fact that it is now well known that Bash&apos;s alloys contained impurities which strongly affected their thermoelectric behavior.

Jan 1, 1962

By Nicholas J. Grant, Rolf Nordheim, Thomas B. King

Constant-load creep-rupture tests were conducted in an argon atmosphere at temperatures of 1600 to 2200°F on two heats of iron containing about 0.06 and 0.09 pct P in solid solution. The tests were conducted in the as-cast condition. Stresses were selected to give strain rates approaching those encountered in the hot working of steel, and within the limits of the creep-rupture test apparatus, namely. from about 0.001 to 50 pct per sec. FOR generations, rolling and forging practices have been developed largely by empirical methods, based on prior experience. While largely successful, difficulties are frequently encountered when new or different alloy compositions are tried for the first time. There is need to know the relationships which exist among temperature, strain rate, composition, and other variables on the deformation and fracture characteristics of steels. It has been shown for aluminum and several high-temperature alloys that the deformation and fracture characteristics follow rather well-defined laws and patterns which are closely related to the effects of strain rate, temperature, and composition.1"3 As the melting temperature of aluminum or its alloys was approached, it was possible to study the interplay of work-hardening factors and recovery or recrystal-lization, the latter resulting in improved ductility and increased resistance to intercrystalline fracture. In particular, the effects of composition are very poorly known. Within the meaning of "composition" should be included impurity elements, such as sulfur, phosphorous, lead, copper, and many others, as well as those elements which are added for alloying purposes in iron. The role of multiphase structures, in contrast to solid solutions, should also be studied in much greater detail. high strain rate creep-rupture tests would provide information regarding the deformation and fracture characteristics of metals at hot-working temperatures. It was also desired to establish the stresses which are necessary to accomplish the desired deformation, and to relate these to the strain rate and temperature. Secondly, it was the purpose of this particular study to determine the effects of phosphorus, within solid solution limits, on the deformation and fracture characteristics of iron at hot-working temperatures. EXPERIMENTAL PROCEDURE Two phosphorus levels were selected, one corresponding to the upper limit normally found for commercial steels, and one substantially higher than this, but within the region of solid solubility at the test temperatures chosen for this investigation. Twenty-pound heats were prepared by induction melting electrolytic iron in air in a magnesia lined furnace. After deoxidation with about 0.2 pct Al, ferro-phosphorus was added, and the heats were then poured into prefired silica molds. The purpose of using silica molds was to obtain a slow cooling rate during solidification to produce a relatively coarse grain size, producing a structure subject to some segregation and therefore more nearly characteristic of ingot structures. The major part of the casting assembly provided a large shrinkage head in order to produce sound castings and to promote slow cooling of the specimens. The primary austenitic grain size varied from ASTM No. 2 to No. 00. The composition of the heats, including a low phorphorus melt, used for comparison purposes, is shown in Table I. It will be noted that the oxygen content of the phosphorus containing heats is relatively high, in spite of the deoxidation practice, a condition which is difficult to control in small melts. Creep-rupture tests were nevertheless undertaken when it was noted that this quantity of oxygen did not appear to give results any different from those from a heat containing 0.01 pct 0, low phosphorus and comparable carbon Content;4 see Table 11.

Jan 1, 1961

By George W. Bain

Some problems concomitant with commercial exploitalion of marble are presented as examples of interesting, useful and profitable fields for application of scientific knowledge. The marble industry is only one such field and is selected because its varying new aspects are familiar to the author. However, what is true for marble is equally so in principle for many industrial minerals. The problems of any stone industry are to maintain markets, create new outlets for stone already in demand, and develop varied uses for varieties that are not so popular. Here the geologist has a different role from most of his colleagues in metal mining. The producing branch may ask about the expectable variation in thickness or size of a deposit as development proceeds. The stock department may call for the available amount of a given type of stone before accepting a large order. The sales force requires data on the use for stone from certain parts of deposits in order to divert grades to the most suitable use. The service department wants defects rectified and the cause determined to avoid recurrence The mills want data on durability and cutting quality of abrasives. The geologist occupies no special department; he is on general call, as may be illustrated by a few types of problems that may be classified as: (1) dominantly geological in character, (2) dominantly chemical in character, (3) dominantly physical in character. Geological Problems The geological problems deal almost exclusively with the size of blocks. Size across the deposit is limited by thickness of individual beds. and along the strike by the space between crosscutting joints. Frequently the vertical depth of a block is reduced by exfoliation shells arising from spontaneous expansion. All these factors require consideration in developing a deposit to fill an order. Thickening of Marble Beds The limestone beds that became the marble deposits of the northern Appalachians and of the Yule locality in Colorado were seldom homo-

Jan 1, 1941

By George W. Bain

Some problems concomitant with commercial exploitalion of marble are presented as examples of interesting, useful and profitable fields for application of scientific knowledge. The marble industry is only one such field and is selected because its varying new aspects are familiar to the author. However, what is true for marble is equally so in principle for many industrial minerals. The problems of any stone industry are to maintain markets, create new outlets for stone already in demand, and develop varied uses for varieties that are not so popular. Here the geologist has a different role from most of his colleagues in metal mining. The producing branch may ask about the expectable variation in thickness or size of a deposit as development proceeds. The stock department may call for the available amount of a given type of stone before accepting a large order. The sales force requires data on the use for stone from certain parts of deposits in order to divert grades to the most suitable use. The service department wants defects rectified and the cause determined to avoid recurrence The mills want data on durability and cutting quality of abrasives. The geologist occupies no special department; he is on general call, as may be illustrated by a few types of problems that may be classified as: (1) dominantly geological in character, (2) dominantly chemical in character, (3) dominantly physical in character. Geological Problems The geological problems deal almost exclusively with the size of blocks. Size across the deposit is limited by thickness of individual beds. and along the strike by the space between crosscutting joints. Frequently the vertical depth of a block is reduced by exfoliation shells arising from spontaneous expansion. All these factors require consideration in developing a deposit to fill an order. Thickening of Marble Beds The limestone beds that became the marble deposits of the northern Appalachians and of the Yule locality in Colorado were seldom homo-

Jan 1, 1941

By Rudolf K. Berkhard

Static soil investigations with more or less heavy loads and extensive borings do not always have efficient results; also, they are very expensive. The new geophysical method of dynamic tests described herein is simple and cheap and avoids several disadvantages of the routine investigation, thus forming a useful supplement to the older methods and even at times replacing various static tests. The fundamental principle of dynamic soil tests consists in the application of artificial vibration. The technique employed is essentially geophysical in nature and in some respects is akin to seismic studies. Artificial vibration may be excited by centrifugal forces resulting from eccentrically supported rotating masses. The reactions of soil and structures caused by these vibrations may be measured. Their dynamic constants, such as amplitudes, phase speeds, damping, reflection, and interference effects, can be investigated. This geophysical method has been used for several years with increasing success. The results of these tests, summarized at the end of the paper, indicate that this method opens a new field for the pkactical engineer in investigating soils (capacity and formation), foundations, dams and structures, and especially buildings that must withstand earthquakes. Methods Static Method.—The first and oldest tests to investigate the bearing capacity of the soil were carried out by static weights. The penetration of these weights, however, depends not only on the soil but also on the size and the form of their lower surface. The length of time the load acts is also important. To imitate actual field conditions, heavy weights and lengthy tests are required, both of which are expensive. Furthermore, the influence of static weights affects only the surface and does not penetrate into deeper strata, therefore substitutes and supplements for static tests have to include the time factor and consequently lead to dynamic investigations. Such dynamic investigations also affect

Jan 1, 1940

By Rudolf K. Berkhard

Static soil investigations with more or less heavy loads and extensive borings do not always have efficient results; also, they are very expensive. The new geophysical method of dynamic tests described herein is simple and cheap and avoids several disadvantages of the routine investigation, thus forming a useful supplement to the older methods and even at times replacing various static tests. The fundamental principle of dynamic soil tests consists in the application of artificial vibration. The technique employed is essentially geophysical in nature and in some respects is akin to seismic studies. Artificial vibration may be excited by centrifugal forces resulting from eccentrically supported rotating masses. The reactions of soil and structures caused by these vibrations may be measured. Their dynamic constants, such as amplitudes, phase speeds, damping, reflection, and interference effects, can be investigated. This geophysical method has been used for several years with increasing success. The results of these tests, summarized at the end of the paper, indicate that this method opens a new field for the pkactical engineer in investigating soils (capacity and formation), foundations, dams and structures, and especially buildings that must withstand earthquakes. Methods Static Method.—The first and oldest tests to investigate the bearing capacity of the soil were carried out by static weights. The penetration of these weights, however, depends not only on the soil but also on the size and the form of their lower surface. The length of time the load acts is also important. To imitate actual field conditions, heavy weights and lengthy tests are required, both of which are expensive. Furthermore, the influence of static weights affects only the surface and does not penetrate into deeper strata, therefore substitutes and supplements for static tests have to include the time factor and consequently lead to dynamic investigations. Such dynamic investigations also affect

Jan 1, 1940

By W. I. Duvall, D. E. Stephenson. Discussion by R. G. K. Morrison

R.G.K. Morrison (Chairman, Dept. of Mining Engineering and Applied Geophysics, McGill University, Montreal, Que. Canada) - The authors have introduced a subject, the intensive study of which has awaited scientific developments. These are now such as to justify a thorough review of our thinking on the causes and control of rockbursts. The formulae developed in the paper, the comparison between rockbursts and earthquakes in figure 1 and the energy data relating to explosives serve as an effective foundation. In the paper this writer is quoted as suggesting that energy of the order of 10 x 10 11 ft. lb. may have been released in some of the heaviest rockbursts in the Kolar Gold Field. He now hastens to add that such an estimate has no scientific validity. It arises only from a casual comparison of surface and underground effects of the medium heavy bursts, referred to in the paper and estimated by Jones at 3.0 x 1010 ft.lbs., with those of obviously greater magnitude. In any case, we have the estimate by Jones above, that by a team of seismologists 1 on the Witwatersrand of 10 x 1010 ft.lbs., that by Coates of 3.8 x 10" ft.lbs., also referred to in the paper, that by Blan-chard2 for the catastrophic rockburst at Springhill, N.S., of only 7.4 X 107 ft. lbs., and finally the range covered by Cook, referred to in the paper. It is probable also that data for the heavy rockburst at Merkers3 in the WERRA potash area of Germany are available as it was recorded on seismographs from Moscow to Spain. It is the writer&apos;s impression that some standardization is present in the estimates above for 10 x 10 10, 3.8 x 1010 and 7.4 x 107 ft.lbs., respectively. The latter, for Springhill, represents a relatively low order of magnitude. It is obvious that any energy estimate must be related to the local geometry of openings at the time of the event. It is also obvious that any explanation of the causes of rockburst must be capable of providing a wide range of energy. However, we must remember that the energy release is an effect indicating magnitude. The cause lies with the mechanism initiating the primary failure, generating the seismic activity, to which much of the damage is probably due.

Jan 1, 1967

By J. A. Knox, R. M. Lasater, J. M. Tinsley

Chemical squeeze treatments have been used to provide temporary relief from certain production problems. The chemical fracture-squeeze technique, combining the effects of a fracturing treatment and a squeeze operation, has been more successful than conventional squeeze operations. Knowledge derived from well stimulation and reservoir engineering research provides a means for predicting the theoretical effective life of such a treatment. Analysis of theoretical equations and concepts developed allows selection of improved treatment techniques based on specific formation conditioins. Theory used in this analysis was developed as an extension of previous electrical model studies made to establish the expected flow and pressure profiles adjacent to a fracture system. The chemical fracture squeeze technique can be utilized in the economic application of corrosion inhibitors, emulsion breakers and paraffin and scale inhibitors. Application of this technique is shown to be effective. The slow return rate of injected chemicals, controlled by the resultant flow profiles and treatment variables, permits extended periods of chemical effectiveness. Results of field treatments are given, showing that the concepts outlined above for chemical fracture-squeeze treatments are valid and that applying this technique can help alleviate many current production problems. INTRODUCTION Much progress has been made in the last 10 to 15 years in developing chemicals for use in stimulating wells, maintaining production and protecting well equipment from damage due to corrosion. Not too many years ago, some wells seemed to dry up or wear out. In many cases the wells were produced as long as possible without any attempt at maintaining productivity. Even with the advent of new and better stimulation techniques, a rapid decline in production was observed. Methods of removing and, in some instances, preventing damage have been developed. Among thosc factors responsible for uneconomical production are scale, paraffin, corrosion, bacteria, water blocks and emulsions. Soluble scale-prevention chemicals have been developed1,2 that can be placed in a formation along with frac- turing sand. As the water produces back across this bed, the solid material dissolves slowly and can provide long-term protection from scale. However, bottom-hole temperature and salinity of produced water vary widely and both these factors influence the rate of solubility. Scale inhibitor composition is also a controlling factor. Some of the solid material may be crushed, increasing the surface area exposed to water and increasing the rate at which it dissolves. Some of the material may never be contacted by water and can be lost. However, this type of treatment has been very successful in many instances and has helped maintain economical production for extended periods of time. Liquid scale inhibitors, which are more widely applicable and more stable, have been developed in recent years; however, because they are liquids, their use has been restricted to treatment down the annulus, using metering pumps to provide proper concentrations in the produced fluid. This has prevented use in wells containing packers, in dually completed wells and in gas-lift and flowing wells. Wells that operate with an open annulus may also experience severe corrosion problems due to introduction of oxygen. Paraffin inhibitors3 have been developed that can be fractured into a well as particulate solids to be slowly dissolved in the produced fluid. These materials are not usually effective in wells with a bottom-hole temperature in excess of 120F since solubility rate may be too fast if that temperature is exceeded or if aromatic content of the oils is unusually high. Corrosion inhibitors have been developed that can be fractured&apos; into a well for long-term feedback, but development of a material with proper solubility or feed rate has been difficult. Corrosion inhibitors are available in many different forms. Liquids have been lubricated down the annulus or sticks or pellets dropped down tubing. Inhibitor squeeze treatments5 devcloped a few years ago led to development of inhibitors with particularly strong film-forming properties.6,7 This technique basically involves displacing a highly concentrated solution of the inhibitor into the formation through the tubing. Kerver and Hanson8 studied the adsorption properties of inhibitors on various types of formations. They showed that, even though the inhibitor was displaced radially into the true permeability, it could be produced back for a long period of time because of slow desorption from the rock. Methods developed for monitoring the return of these inhibitors generally have established 1 to 6 months as the effective limit before retreatment is necessary.9 Inhibitors displaced into the interstices of the formation sometimes cause emulsions that either hamper production or cause treating problems on the surface.

By Jeffrey W. Nelson

Predictions of creep closure for periods ranging up to more than 1,000 years are needed for designing a radioactive waste repository in a salt formation. Such long-term predictions must be based on the use of laboratory and field test results extrapolated by numerical modeling. Laboratory test results are presented which show highly variable creep behavior for salts from different sites as well as salts from the same site. Comparisons of measured creep closures against predicted closures are presented for two deep boreholes in Louisiana salt domes and for an exploratory shaft and drift in southeastern New Mexico bedded salt (WIPP). These data illustrate the significant uncertainties involved in long-term closure predictions and indicate the critical need for site-specific, in situ closure measurements over extended periods of time for repository design.

Jan 1, 1984

By Sam Harlan

At intervals during the past several years the oil industry has been confronted with the problem of forestalling crises in its affairs. These crises have been reduced to periods of depression which, fortunately, the industry has been able to survive. Under the existing competitive practices which control the producing division of the industry it apparently has been proved that the best efforts logically to curtail development and producing operations are inadequate for effecting a true production balance and the consequent stabilization of prices. The industry is awakening to the fact that the situation warrants revolutionary thought and at this time it is looking for a permanent solution of its problem in a general plan for unit development and operation such as the one first proposed by Henry L. Doherty. Mr. Doherty&apos;s proposal was designed not only as a means for stabilizing the industry as a whole, but its principles involve very definite potential benefits for the average individual operator and royalty owner as participants in pooled projects. The benefits to these individuals would be derived from maximum recovery, the maximum utilization of natural energies, the minimization of development and operating costs, enhanced values of leases and royalties through improved efficiencies and ultimate yields, improved earnings through stabilized crude oil prices, etc. This plan was revolutionary to the industry&apos;s practices and at the time was rejected, but it now appears that the development and operating policies for new properties are continually approaching the ideal of the original plan. Oil companies are constantly extending their efforts to improve all factors that have a bearing on the costs and efficiencies of their operations. These efforts may, in some degree, be a normal outgrowth of the industry&apos;s progress, but the forced consideration of market conditions, the growing appreciation of the importance of regulating operations for maximum ultimate economies and the depreciation of the old principle of maximum flush at any cost, come from a new school of thought which has been stimulated by the immediate pressure of overproduction and

Jan 1, 1930

By Yoichi Ishida, Ching-Yao Cheng, John E. Dorn

Tile creep behavior of a iron was investigated over the range of temperatures from 375° to 1150°K. Apparent activation energies for creep, obtained by the effect of sudden changes in temperature on the creep rate, revealed the presence of- four distinguishable regions. The creep behavior of a iron in Regions II (480° to 774°K) and 111 (775° to 1045°K) was found to correlate well with a model where the creep rate is controlled by the nonconsevualive motion. of jogged screw dislocations. An anomalous increase in the apparent activation energy fur creep in Region III was found to be in harmony with the known decrease in the free activation energy for self-diffusion over the Curie transformation range. Furthermore, the creep rates in Regions II and III were found to increase with stress due not only to the effect of stress on the activation energy but also to an increase in density of mobile dislocations. The evidence suggests that pipe diffusion along moving dislocations could be a significant factor over the lower temperatures of Region II. ALTHOUGH the creep properties of iron and steel have been of interest to metallurgists for some time and an extensive literature is now available, most of the published information has not produced much toward understanding the fundamental dislocation processes controlling the creep behavior of these materials. Whereas the activation energy for high-temperature creep of metals usually agrees well with that for self-diffusion, Sherby, Orr, and Dorn1 deduced from the data of Tapsell -and c1enshaw2 that the activation energy for creep of Armco iron is about 78,000 cal per mole and more recently Lytton and sherby3 reviewed the data of Jenkins and Mellor4 and found an activation energy for creep of a iron of 80,000 cal per mole. Both values are substantially greater than the activation energy for self-diffusion in a iron. Because of the limited data suitable for purposes of identifying the controlling dislocation mechanisms of creep and the unusually high activation energies for creep quoted above, it was considered desirable to reinvestigate in detail the creep of a iron by more reliable techniques which would provide sufficient data for determination of the creep mechanisms. EXPERIMENTAL TECHNIQUE Creep specimens were prepared from 3/8 by 4 in. iron bar stock of the following composition by weight percent: 0.001 C, 0.0120 0, 0.001 N, 0.004 S, and 0.003 P. The as-received bars were cold-rolled to a thickness of 0.100 in., annealed under argon for 30 min at 1113°K, cold-rolled to a final thickness of 0.063 in., and machined into tensile specimens having gage section 0.250 in. wide and 1.70 in. long. Finally they were recrystallized under argon at 1113°K. Specimens to be crept above 1060°K were recrystallized at 1173°K. Both recrystallization treatments gave the same reproducible equiaxed ASTM No. 4 grain size. Creep testing was conducted in machines fitted with Andrade-Chalmers arms that maintained a constant stress to within ±0.2 pct of the reported values. Deformation over the specimen gage section was sensed with a linear differential transformer and recorded auto-graphically as a function of time. The strains deduced from these measurements were sensitive to ±5 x 10-5. During creep the specimens were contained in an argon-filled chamber which was immersed in a temperature-controlled molten tin bath. Creep temperatures, as measured by thermocouples attached to the specimen, were maintained to within ±10.25°K of the reported values. For activation-energy determinations rapid changes in temperature of about 12°K were obtained within 30 sec by direct resistance heating of the creep specimen, and maintained to ±1°K of the reported values. Observations of structural details of specimens before and after creep tests were made by electrolytic polishing and etching in acqueous ammonium persulfate. EXPERIMENTAL RESULTS A typical example of the determination of apparent activation energies, Q, by the effect of small changes in temperature is illustrated in Fig. 1. Q is defined by

Jan 1, 1967

By R. G. Treuting

Germanium single crystals strained in tension at 600°C slip on the {Ill} plane and, macroscopically at least, in the <110> direction. Deformation is in homogeneous: various localized rotations are observed, as is a banding consistent with secondary slip banding. The structure after deformation is polygonized with a domain size of about 2x1O-3 cm. In relaxation tests, an incubation period prior to flow is observed, of duration inversely related to temperature and applied stress. Under continuous loading, there is a sharp first yield point. A critical resolved shear stress therefore must be cited with respect both to temperature and to rate of loading. At 600°C, when loading proceeds at 2900 psi per min, it is 1310 psi. The yield point phenomenon is suggestive of Cottrell&apos;s solute atom atmosphere theory and five points of qualitative agreement with this theory are found. PLASTICITY of germanium at elevated temperatures has been reported by Gallagher,&apos; who ascribed it to slip on {Ill) planes and described some associated effects. Preliminary experiments with single crystals of silicon and germanium loaded as simple beams confirmed {ill) as the slip plane of both materials.V his was demonstrated by the standard technique employing traces on two surfaces of known angle on a deformed crystal of known orientation.3 These experiments did not fix the slip direction, since more than one glide system operated. Uniaxial tensile straining is preferred for this purpose in order to restrict slip to one predominant system and to provide an unequivocal determination of the orientation change with respect to the stress axis. Experimental Method Specimens were diamond-sawed from germanium crystals containing about 5x10-5 wt pct Sb prepared by the zone-leveling process described by Pfann and Olsen;4 these specimens measured about 81/2 in. long, 0.20 in. wide, and were of various thicknesses from 0.035 to 0.060 in. Prior to testing, a specimen was coated over 1 in. or more of length at each end with Apiezon wax, chemically polished (in a solution of 15 ml HF, 25 ml HNO,, 15 ml CH3COOH, and 3 to 4 drops Br2), and dewaxed in warm xylene. A brief re-etching after scribing through a complete wax coating with vernier dividers provided gage marks at 0.200 in. intervals on the polished surface. A specimen with grips soft soldered to the ends was passed through the furnace tube and the grips pinned to the tensile machine in series with a stress gage. The Schopper testing machine is best described by reference to the illustration on p. 107 of Schmid and Boas5 and is operated with the pendulum arm locked, fixing the upper head. Load is applied through the screw-driven lower head, manually or by reduced speed motor. The furnace is 21/2 in. long surrounding a 4x7/16 in. ID quartz tube and was positioned about the specimen to permit free motion. The inert or reducing atmosphere required was sufficiently provided by a flow of helium introduced at the center of the furnace tube, with the tube ends loosely plugged with asbestos paper. Surface corrosion was slight. The stress gage employs a Be-Cu strip with SR-4 units incorporated in a simple bridge network with provision for balancing and calibrating. The bridge output on loading is fed through a Leeds and North-rup dc amplifier to a Speedomax 10 mv recorder, and calibration is obtained by dead loading. Experiments of two types have been conducted. Most have been in relaxation at constant elongation. One stress-strain curve has been taken with the machine continuously driven. Following extension of a specimen, Laue X-ray photographs were taken to obtain the orientation change between deformed and undeformed regions, recorded on a single film by translating the specimen in a plane normal to the beam between exposures. Sequences of such multiple exposures were made on some specimens to include the entire orientation range on one film. Slip Direction To obtain a maximum orientation change with a single slip system, crystals of very closely <110> axial orientation were used. The classic determination of slip direction rests on establishing that direc-

Jan 1, 1956

By Paul B. Crawford, Melvin B. Burton

A procedure is given which describes how the gelatin model may be-used to study the effect of mobility ratio on areas swept before and after breakthrough in fluid injection programs. Differences in mobility ratio are achieved through the proper selection of electrolytes for the invading and displaced fluids. The progress of the front is followed visually and photographed or traced onto plates (it desirrd positions before and after breakthrough. Example applications to standard flooding pattrrrls, vertically and horizontally fractured reservoirs and the in-situ combustion recovery process ore presentrtl. INTRODUCTION In water flooding, gas cycling and other fluid injection programs, the sweep efficiencies and swept areas after breakthrough are known to depend on the mobility ratio. Previous investigators have described the application of the X-ray technique, stepwise use of the poten-tiometric model and numerical procedures for studying these problems.1,3,4,6 Others have described the application of the electrolytic and gelatin models for studying sweep efficiencies at a mobility ratio near one.2,5,7,8,9 It is a purpose of this paper to describe a procedure for using the gelatin model to study swept areas at mobility ratios other than one. PROCEDURE The technique developed for gelatin model studies is composed of four phases: the construction of the model, the selection and preparation of electrolytes, the running procedure, and the recording of the swept areas. Each phase is discussed independently in order that the over-all procedure will not be confused. Construction of the Model Since some of the advantages of the gelatin model are its economy, and speed, it is desirable to have as small a model as is possihle without creating error through the inability to follow visually the progress of the colored front. For this work, it was found that a distance of 4 to 6 cm between salt bridges is convenient to use. Since the size is relatively small, it follows that the gelatin layer must be thin. For this study, 1/8 in. was used as the gelatin thickness in each case. The model was constructed on a flat 1/2-in. plastic (Lucite) base with boundaries constructed from 1/8-in. plastic strips. The well pattern to be studied was outlined with the 1/8-in. plastic strips on the base with narrow apertures (- - 2 mm) in the boundary to represent the wells. Behind each well opening, a rectangular area of some 8 to 12 sq cm was outlined by additional plastic strips. The plastic strips were fastened to the base by any suitable non-conducting cement so that the boundary system was liquid tight. The electrodes were constructed from sheet copper in a fashion that would allow easy removal. In this work, it was found that by simply forming a large U-shaped clip from a strip of the copper that would slip over the boundary was satisfactory and easily removed. The electrodes should be as wide as one of the sides of the rectangular area behind the well opening. If a fractured pattern is studied, fractures inside the well pattern may be represented by strips of copper of the desired shape mounted in some easily removable fashion. The reason that apertures (or salt bridges) were used for wells instead of metallic electrodes is that the plating of the electroactive ion at the cathode and the introduction of an electroactive ion at the anode has a detrimental effect on the swept area outline if these operations \rere permitted to be carried on within the well pattern itself. The anode may be used within the well pattern

Jan 1, 1957

By E. P. Klier

THE work of Klier and Lyman1 on the bainite reaction has led to the full description of this reaction for medium-carbon low-alloy steels. Certain experimental data reported by Klier and Lyman appear, however, to be improbable of obtaining in very high-carbon steels. The study herein reported consists of an analysis of the transformation characteristics of a 3 per cent chromium, 1 per cent carbon steel by means of X-ray and metallographic methods. From the results obtained it is concluded that the bainite reaction in this steel is more complicated than that reported by Klier and Lyman for the low-carbon low-alloy steels. However, the mechanism of bainite formation in this steel appears to be essentially the same as proposed for the low-carbon low-alloy steels with the modification that the first volumes to transform are carbon-rich rather than carbon-poor. EXPERIMENTAL PROCEDURE The analysis of the steel studied was: Cr, 2.89; C, 1.02; Mn, 0.33; Si, 0.35; S, 0.012; P, 0.020. The stock was received from the Carpenter Steel Co. in rolled bars. Specimen Preparation Specimens were austenitized at 1200°C. (2192°F.) for 25 min. in purified nitrogen. The resultant A.S.T.M. austenite grain size was 0-1. Isothermal transformation was allowed by quenching the specimens into liquid metal baths controlled to ±5°C. at 540°C. (1004°°F.) and above, and to ±2°C. at 490°C. (914°°F.) and below. Following the desired degree of transformation all specimens were water quenched. Metallographic Examination Specimens 1/4 in. round by 1/4 in. were used for metallographic examination. Etchants used were Vilella&apos;s reagent (1 gram picric acid, 10 ml. hydrochloric acid to make l00 ml. ethyl alcohol solution) and alkaline sodium picrate (electrolytic). Vilella&apos;s reagent was effective in revealing all microconstituents, while the alkaline sodium picrate developed the carbon-rich structures or carbides only. X-ray Examination Two X-ray techniques were used-the Debye-Scherrer method and a back-reflection method. The small specimens necessary for the Debye-Scherrer method were austenitized and then allowed to transform, or were cut from the larger metallographic specimens. The metallographic specimens were used for the back-reflection X-ray analysis. When it was desirable to determine the structure of the carbide present, sliver specimens were electrolytically etched to develop a carbide coating, then were exposed in the cameras. This technique was frequently necessary to allow positive identification of the carbide.

Jan 1, 1945

By E. P. Klier

The work of Klier and Lyman1 on the bainite reaction has led to the full description of this reaction for medium-carbon low-alloy steels. Certain experimental data reported by Klier and Lyman appear, however, to be improbable of obtaining in very high-carbon steels. The study herein reported consists of an analysis of the transformation characteristics of a 3 per cent chromium, I per cent carbon steel by means of X-ray and metallographic methods. From the results obtained it is concluded that the bainite reaction in this steel is more complicated than that reported by Klier and Lyman for the low-carbon low-alloy steels. Henever, the mechanism of bainite formation in this steel appears to be essentially the same as proposed for the low-carbon low-alloy steels with the modification that the first volumes to transform are carbon-rich rather than carbon-poor. Experimental Procedure The analysis of the steel studied was: Cr, 2.89; C, 1.02; Mn, 0.33; Si, o.35; S, 0.012; P, 0.020. The stock was received from the Carpenter Steel Co. in rolled bars. Specimen Preparation Specimens were austenitized at 1200°C. (2192°F.) for 25 min. in purified nitrogen. The resultant A.S.T.M. austenite grain size was 0-1. Isothermal transformation was allowed by quenching the specimens into liquid metal baths controlled to 5°C. at 540°C. (1004°F.) and above, and to 2°C. at 490°C. (914°f.) and below. Following the desired degree of transformation all specimens were water quenched. Metallographic Examination Specimens 1/4 in. round by 1/4 in. were used for nietallographic examination. Etch-ants used were Vilella&apos;s reagent (I gram picric acid, 10 ml. hydrochloric acid to make 100 ml. ethyl alcohol solution) and alkalinc sodium picratc (electrolytic). Vilella&apos;s reagent was effective in revealing all microconstitucnts, while the alkaline sodium picrate developed the carbon-rich structures or carbides only. X-ray Examination Two X-ray techniques were used—the Debye-Scherrer method and a back-reflection method. &apos;The small specimens necessary for the Debye-Scherrer method were austenitized and then allowed to transform, or were cut from the larger metallographic specimens. The metallographic specimens were used for the back-reflection X-ray analysis. When it was desirable to determine the structure of the carbide present, sliver specimens were electrolytically etched to develop a carbide coating, then were exposed in the cameras. This technique was frequently necessary to allow positive identification of the carbide.

Jan 1, 1945

By John D. Price

COAL blending, in the preparation of coal before coke making, is so commonly practiced as to be almost universal. But the reasons underlying this practice, the benefits resulting from it, and the materials used in blending vary widely. This paper will outline the various phases of the subject and present information which may be correlated with work that has been done elsewhere. It will deal entirely with work done on the high-volatile coking coals of the western part of the United States, special emphasis being given to the coals of Colorado and Utah. A surveyL of the 86 coke plants in active operation in the United States during 1949 indicates that only 9 plants, or 10.5 pct of the total, charged one single rank of coal into their ovens, while the remaining 89.5 pcl made use of blending in some form. This report indicated that of these total plants 5 used straight high-volatile coal, 4 used straight medium-volatile coal, 47 used blends of high and low-vola-tile coals, 25 used blends of high, medium, and low-volatile coals, 2 used blends of high and medium-volatile coals, 3 used blends of medium and low-volatile coals. The fact that certain plants operated on a single kind of coal should not be interpreted to mean that no blending was practiced there, for invariably such plants secure their coal from more than one source and in the interest of uniformity do blend the coals as received. The general term coal blending covers two fields, the first of which is the mechanical mixing of a number of coals to secure uniformity. Often it is found necessary to secure coal for coke production from a number of different mines; these coals, though of the same general type or rank, may differ in their chemical composition or in the physical qualities they impart to coke made from them. Again, it is not unusual to find that coal from different sections of the same mine may show variations in quality. Under such conditions it may be necessary, in the interest of a uniform final product, to introduce a system of blending bins, a bedding yard, or other mechanical methods of securing a uniform mixture. Unfortunately this form of blending has received very little attention up to the present time; it has not received the consideration its value merits. The second type of blending, while also for the purpose of coke improvement, deals more particularly with the use of a blending agent differing in character from the base coal: it is this form of blending that will be discussed here. To consider only the western coals, for blending may be found necessary for other reasons with other coals, blending has been practiced experimentally or commercially under the following conditions: 1—When a single coal or mixture of coals of the same rank does not produce a satisfactory coke. For example, a high-volatile coal when used alone is likely to contract when coked so that a comparatively weak coke is formed. Or, if of very low rank, the coal may be deficient in the necessary bitumens required for good coke production. 2—When a product of some special quality is required, for example, when a plant ordinarily producing blast furnace coke must operate at slow coking rate to produce a high-grade foundry coke. Under this condition the reduced daily production of all products which accompanies slow coking time may be undesirable, and the use of some blending agent to increase the size of coke made at faster coking rates may be necessary. 3—When greater yield of coke or its coproducts is needed. Depending upon economic values of the products it may be found desirable to increase the yield of one or the other. 4—When supply of a particular coal must be used, either to protect reserves of high quality coking coal or to utilize a surplus or inferior product not otherwise usable. Many materials have been used for blending purposes, the exact agent to be used depending both upon the condition to be corrected and the nature of the base coal. No universal blending agent that can

Jan 1, 1954

By J. F. Martin, L. M. Melnick, R. Rapp, R. C. Takacs

Recent studies on the determination of hydrogen in steel have shown that the hot-extraction method for removing hydrogen from a solid sample is preferable to its removal from a molten sample by vacuum fusion or by fusion in vacuum with tin. A number of techniques are available, however, for determining the hydrogen so extracted. They include: thermal conductivity, gas chromatography, pressure measurement before and after catalytic oxidation of the hydrogen to water and removal of the water, and pressure measurement before and after diffusion of the hydrogen through a palladium membrane. These techniques have been evaluated on the basis of initial cost, maintenance, speed and accuracy of analysis, and applicable concentration range. The results of this study showed that the palladium-membrane technique is best suited for routine use. FOR some time investigators have been concerned with the origin, form, and effect of hydrogen in steel. In such stdies&apos;, the analysis for hydrogen constitutes one of the most important phases. It is quite apparent that the results for hydrogen concentrations in a given steel are dependent on the method of obtaining the sample, storage of the sample until analysis, preparation of the sample, and analysis of the sample, including all the facets inherent in the calibration and operation of an apparatus for gas analysis. There are a number of means available for determining hydrogen. This is a critical study of some of the more common techniques in use today. In most conventional melting and casting methods, hydrogen concentrations of 4 to 6 parts per million (ppm) in steel are quite common. Because of the undesirable effects of hydrogen on steel there has been increased use of techniques such as vacuum melting,&apos; vacuum casting, and ladle-to-ladle stream degassing, which lower the hydrogen content to levels on the order of 1 to 2 ppm. Therefore, the method used for determining hydrogen in steel must be sensitive and precise. In any analytical procedure for gases in metals there are two distinct operations—the extraction of the gas from the metal and the analysis of the extracted gas. To extract the gas from the steel, three methods have been employed: 1) fusion of the sample with graphite at high temperature; 2) fusion with a flux, such as tin, at a lower temperature; and 3) extraction of the hydrogen from the solid sample at a temperature below the melting point of the steel. Fusion with graphite is the least-acceptable method. The blank in this method is higher and more variable than in either of the other two methods. The hydrogen fraction of the total gas composition usually is between 10 and 50 pct; thus, a larger analytical error is possible. The vacuum-tin fusion4 extraction of hydrogen is probably the most rapid method in use today; the extraction time is usually about 10 min. However, with this system a bake-out of the freshly charged tin for 2 hr is necessary and a change of crucible and a charge of fresh tin are required after each day of operation whether one or thirty samples have been analyzed. In addition, frequent checks of blank rates are required since CO and Na are continually being given up by the steel samples dissolved in the tin bath. The composition of the gas in this method lends itself readily to analysis; although the hydroge concentration may fall to as low as 50 pct, more often it is above 90 pct, thus allowing a more precise analysis (because of less interference from other gases). In 1940 ewell&apos; published the hot-extraction method for extracting hydrogen from the solid sample, comparing analysis for hydrogen extracted at 600°C with similar analysis for the gas extracted at 1700°C by fusion with graphite. Good agreement for hydrogen was obtained between these two methods, provided sufficient time was allowed for extraction at the lower temperature. carsone obtained good results in his comparison of this hot-extraction method with vacuum-tin fusion. Subsequent work by Geller and sun7 and Hill and ohnson&apos; has shown that steel samples should be heated to at least 800°C to effect the release not only of the diffusible hydrogen but also of the "residual" hydrogen that may be present as methane. Since the rate of evolution of hydrogene9l0 depends on such factors as sample size and composition, thermal history, and extent of cold work, a fixed extraction time is not possible. Extraction times of 30 min are normal, but 2 hr are not unusual. Induction or resistance heating may be used in the hot-extraction method. With resistance heating the

Jan 1, 1964

By M. Gell, G. R. Leveran

The high- and low-cycle fatigue properties of the nickel-base superalloy, Mar-MBOO, in columnar-grained and single-crystal forms were determined at room temperature. It was found that the fatigue lives of these materials were greatly affected by the size of preexisting cracks in MC-type carbides contained in the micro structure. Most of the data falls on two curves given by: (zN)&apos;/A€= K, where Nf is the number of cycles to failure, Af is the total strain range, and K is a function of carbide size. No difference was observed in the fatigue behavior of the columnar-grained and single-crystal materials for the same MC carbide size. Matrix slip and crack initiation occurred at precracked MC carbides and, to a lesser extent, at micropores. Fatigue crack propagation was mainly in the Stage I mode, i.e., on cry stallo graPhic slip planes. The Stage I fracture in these materials was unusual in that distinct features were observed on the fracture surfaces. In high-cycle fatigue, these features resembled those commonly observed on the cleavage fracture surfaces of bcc and hcp materials. Yet, in this study, the cracks propagated slowly in a cyclic manner. In low-cycle fatigue, the Stage I facets contained equiaxed dimples, similar to those observed on the tensile fracture surfaces of ductile materials. These observations indicate that both local normal and shear stresses are involved in these Stage I fractures. A model is proposed to explain these results based on the weakening of the cohesive energy of the active slip planes by reversed shear deformation and the fracture of the bonds across the weakened planes by the local normal stress. RECENT developments in casting technology have produced cast nickel-base superalloys in columnar -grained and single-crystal forms.1&apos;2 The tensile and creep properties of the nickel-base superalloy, Mar-M200, cast in these forms have been shown to be superior to the corresponding properties of the conventionally cast polycrystalline material.lp2 This improvement in properties results, in part, from the elimination of grain boundaries in the single crystals and the alignment of the grain boundaries parallel to the stress axis in the columnar-grained castings. As part of a program to evaluate the fatigue properties of nickel-base superalloys cast in single-crystal and columnar-grained forms, a study has been made of the cyclic deformation and fracture of Mar-M2OO at room temperature. M. fiFl I .hininr Mpmher AIMF ic ^pninr Rocoarrh Accn^iata anH I) EXPERIMENTAL PROCEDURE The composition range of Mar-Ma00 in weight percent is: 8 to 10 Cr, 9 to 11 Co, 11.5 to 13.5 W, 0.75 to 1.25 Cb, 1.75 to 2.25 Ti, 4.75 to 5.25 Al, 0.01 to 0.02 B, 0.03 to 0.08 Zr, 0.07 to 0.12 C, bal. Ni. All of the castings met the above specifications. The castings were solutionized for 1 to 4 hr at 2250°F followed by aging at 1600°F for 32 hr which resulted in a 0.2 pct offset yield stress of 150,000 psi at room temperature. The microstructure of the material consisted of cuboidal, coherent particles of ordered, fcc Ni3(A1,Ti) (commonly designated y&apos;), approximately 0.3 p on edge, distributed in an fcc y solid-solution matrix. MC carbides together with shrinkage and gas micropores were also distributed throughout the materials. The MC carbides and micropores were located preferentially in the interdendritic interstices, as well as in the grain boundaries in the columnar-grained castings. The (100) direction of all the single crystals and the common (100) axis of the grains in the columnar materials were aligned within about 5 deg of the specimen axis. Fatigue testing was carried out in the high-cycle (HCF) and low-cycle (LCF) fatigue regions, with the major difference being gross yielding of the specimen occurred during the first cycle in the LCF region. This division also corresponded with the more usual one in which the life of a specimen in LCF is less than lo4 cycles and that in HCF is greater than lo4 cycles. The designs of the high-cycle fatigue and low-cycle fatigue specimens are shown in Figs. l(a) and (c), respectively. The gage sections of both HCF and LCF specimens were electropolished prior to testing. The HCF specimens were tested in an MTS, closed-loop, hydraulic fatigue machine at 10 cps in air. The specimens were cycled between a tensile stress of 5000 psi and a maximum tensile stress which ranged from 35,000 to 125,000 psi, Fig. l(b). The LCF specimens were cycled under strain control from zero to a maximum tensile strain, Fig. l(d), in a Wiedemann-Baldwin testing machine. The experimental procedure has been described elsewhere.3&apos;4 Both HCF and LCF tests were interrupted periodically in order to replicate the development of slip and cracking at the specimen surface. This was accomplished by placing plastic replicating tape around the gage section of the specimen while the specimen was in the mahine. The size of the MC carbides for all specimens was measured on a polished longitudinal section through the gage section after fatigue testing. The method of measurement consisted of carefully scanning the entire polished section in order to locate the largest MC carbides. Photographs were then taken of the six longest carbides oriented approximately normal to the

Jan 1, 1969