Search Documents

By Anson Hayes

FOR the purpose of the following discussion the word "research" is interpreted as including all phases of development work on methods of manufacture, metallurgical characteristics, and uses of iron and steel. Research in the iron and steel industry then includes both plant re- search and laboratory research. Since iron and steel came into being, the steel consumer's plant and the steel producer's plant have been important factors in the development of the steel industry. Good minds have always been associated with both consumer and producer plants, so marked progress was made in the industry even when these were the only types of research and development groups in action.

Jan 1, 1937

By William S. McAleer

Two major trends in the coal industry today focus attention on the need for heat-drying equipment of a simpler, more flexible and less expensive type than has been considered standard equipment for drying coal. These trends are: I. The tremendous growth in the use of mechanical equipment to load coal both in underground mining and strip mining, which necessitates efficient mechanical cleaning of the fine as well as the coarse coal and thus means a growing tonnage of washed fine coal? with its attendant moisture problems. 2. The growing consumer demand for the smaller sizes for use as domestic stoker coal, with increasingly rigid specifications covering size, ash, and moisture analyses. ACCEPTED PRACTICE In the past, when, for example, 4 in. too coal has been washed, there was little trouble in producing a washed product 4 to o with a satisfactory resultant moisture. The 4 to 3/8-in. could be taken from dewatering screens at a surface moisture ranging from 2.5 to 3.5 per cent, depending upon the size consist. The 3/8-in. to o coal was generally dewatered satisfactorily with centrifugal driers, to final surface moistures from 5.5 to 8 per cent, again depending upon size consist. The centrifugal type of drier has definitely proved itself to be the most economical type of machine to handle coal approximately 3/8 in. to o as recovered by dewatering screens or drainage elevators with 15 to 25 per cent surface moisture and turn out a product with moistures as stated above. Sometimes such moistures (5.5 to 8.0 per cent) in the product are satisfactory. If not, an ultimate moisture, lower than 3 per cent, is seldom required and the centrifugal drier removes 70 to 85 per cent of the total moisture to be removed. In certain districts there has been a growing tendency to circumvent the use of centrifugals or other types of driers, by dewatering over screens of the wedge wire type and wasting all the finer sizes. Sometimes all the minus 28-mesh has been wasted and often the size wasted has been as large as 1/8-in. By wasting these finer sizes, a lower moisture can be obtained in the finished product, but taking into account the cost of the tonnage so lost, plus the added cost of ultimately disposing of this wasted tonnage, often the cost will be greater than the cost of heat-drying in a modern plant, which makes possible the recovery of all the tonnage. Moreover, with the moisture standards for domestic stoker equipment even these wasteful approaches to its solution do not solve the problem and there remains only the alternative of heat-drying. HEAT-DRYING Until about four years ago, heat-drying of coal at the preparation plants was confined chiefly to drying the fine sizes (approximately 3/8 in. to 0). Occasional

Jan 1, 1941

By I. Tamura, J. O. Brittain, T. Mura

Plain carbon steel in the cold worked or marten-sitic conditions has an internal friction peak at about 250 oC at a frequency of I cps. The influence of substitutional alloying elements on this peak was examined experimentally. The alloys were vacuum melted Co-, Cr-, Mo-, Ni-, and Si-iron (about 3 pct alloying elements), and carburized Si-iron. The internal friction of the alloys in the temperature range 30o to 500 OC was determined by means of a torsion pendulum. The 250 oC peak of the cold-worked alloys was lower in height than that observed in plain C-iron and steel. Carburized Si-iron in the quenched condition had a peak which occurred at a slightly lower temperature than in quenched plain C-steel, but the height of the peak was substantially greater than that found for the same alloy in the cold-worked condition. The activation energy of this peak for martensitic Si-steel was about 35 kcal per mol. ANNEALED a iron has two internal friction peaks due to nitrogen and carbon at 20o and 40o C respectively, at a frequency of 1 cps. If a iron is cold worked, these diffusion peaks become smaller and a new peak appears at about 250o C. The activation energy for the 250o C peak is in the range of 32 to 44 kcal per mol and has an average value of 38 kcal per mo1. It has been experimentally verified that both interstitial solute atoms and dislocations are necessary for the 250o C peak. 3 Wert has also shown that an incubation period precedes the appearance of the 250 C peak.4 With regard to quenched martensitic steel, Ke et al.596 observed two peaks at around 130o and 250o C. They conjectured that the 250o C peak in martensite was due to the same mechanism as the 250°C peak in cold worked a iron, and the 130°C peak was due to the nature of tempered martensite. They did not report the activation energy for these peaks. Chernikova7 found only one peak at about 200° C in tempered martensite. In a previous paperS we reported an activation energy of approximately 40 kcal per mol for the 250° C peak in plain carbon martensitic steels. Ichiyama8 found the activation energy to be about 36 kcal per mol for the 250° C internal friction peak in steels in the martensitic condition. The present authors proposed a theory for the 250°C peak for cold worked and quenched iron and steel.= The theory for the peak is based upon the addition of a strain-energy term to the free energy for the formation of a carbide precipitate due to the presence of a disclocation. The model employed for the relaxation process consists of the growth and solution of a carbide precipitate of critical size as a consequence of an oscillating dislocation. In this report, the influence of substitutional alloy ing elements on the 250° C peak is examined and the experimental results are discussed in terms of our theory for the peak. Most of the experimental work on the alloy steels was confined to the Fe-Si-C alloys.

Jan 1, 1962

By G. A. Reinhardt, H. J. Cutler

ThE Youngstown Sheet & Tube Co. has produced a large tonnage of 0.35 to 0.45 carbon forging steel, the acceptance of which was based on the physical properties of test specimens obtained by forging the original 5 3/4-in. (14.5 cm.) square bloom to a 3/4-in. (1.9 cm.) round. Annealed and tempered specimens were required. The test bars were annealed by heating from 900" to 950' C. and cooling slowly in mica. The test bars were tempered by heating to 825' to 875" C., quenching in water, and drawing to 515" to 535" C. Immediately after heat treatment, the test pieces were machined to a diameter of 0.534 in. (1.38 cm.) and tested. Very good physical properties were obtained and no difficulty was experienced in meeting the specifications called for. UlTimate Strength.. Elongation, Lb. pER Sq. In. PEE Cent.. in 4 In. Not LeEs Than Annealed specimens.............. 78,230 to 92,450. 18 Tempered...................... 120,000 to 149,350 9 After experience on this material, production of slightly higher carbon forging steel was started. The method of testing this material required that test blooms be either normalized or annealed. The normalizing consisted in heating to 850" to 900" C. and cooling in still air; the annealing, in heating to 850" to 900" C. and cooling in the furnace or in mica. From the treated bloom, the test pieces were taken either by core drilling or by sawing from points midway between the edges and the intersection of the diagonals. The cores or blocks were turned to a standard 2-in. test piece with a diameter of 0.564 in. and tested without further treatment. The physical requirements of the test pieces were: yield point, pounds per square inch minimum, 44,800; ultimate strength, pounds per square inch, 89,600 to 112,000; elongation, per cent. in 2 in. not less than 17. Difficulty was encountered as soon as work on this material was started. Many precautions and refinements were instituted but it was found very difficult to secure the required elongation.

Jan 1, 1920

By H. W. Bell

There was considerable prospecting for new supplies of oil in Arkansas during the past year, regardless of the overproduction affecting the industry throughout the country. Justification for this new work was not lacking, as the local markets more than threatened to absorb a declining production. There were, however, no important new discoveries in the state during 1929. The McDonald area in sec. 2515, S.-18 W., threatened to expand into a major producing area. Oil showings had been encountered here in wells drilled by the McDonald Oil Corpn. as early as the fall of 1928. In July, 1929, an initial production of 1000 bbl. of 32" oil was obtained in McDonald Bros. B-3 Wilson, from a sand at 2780 to 2786 ft., which is about 80 ft. higher than the sand previously tested in the neighboring wells. This production declined rapidly. At the end of the year there were six producers making about 200 bbl. per day total. Seven dry holes have temporarily stopped development in that area. The showing of B-3 was sufficient to cause considerable leasing activity. The area lies several miles west of the Louann portion of the Smackover field. The discovery well went to 2873 ft. and found Glen Rose lime in bottom. The age of the producing sand is in doubt; it seems closely related to the Tokio sand. During 1929, several paying wells were brought in, as a northeastern extension to the Smackover Heavy area, in sec. 34 and 35-15-15, from the Nacatoch sand. Over 20 new wells were drilled and resulted in at least 1500 bbl. production. The down-dip or off-structure territory contiguous to the Smackover uplift was further tested at various locations with the usual results; that is, a showing of "salt water gas," which soon blew off and in some cases a slight showing of oil. These gas showings, found further down the dip than oil, are the results of the ability of water to take gas into solution at the rate of about 3 per cent. by volume at atmospheric pressure and proportionally larger quantities, if available, at higher pressures (measured on the absolute scale). During the year no off-structure wrinkles sufficient to trap conlmercial quantities of oil have been found outside of the other known fields of

Jan 1, 1930

As reported in Drift last month demolition of old buildings on the 47th St. site has been completed, and detailed plans and studies for the new structure are well underway. As this issue was being sent to press the $5 million industry- business phase of the fund campaign had passed the half- way mark toward its goal. Target date for the building program is 1960.

Jan 5, 1958

By Charles L. Harness

STRONTIUM is an essential constituent of celestite (strontium sulphate), of the rarer strontianite (strontium carbonate), and of a few very rare minerals. Celestite is the chief ore but strontianite is more valued except for making the purest strontium salts, because of its ease of processing. The public knows strontium mainly as the source of the red flame in fireworks but it has many other uses. PROPERTIES The celestite of commerce is a massive mineral of varying texture: coarsely crystalline, fibrous, bladed, very fine grained or earthy. The color varies greatly with the nature of the impurities but the purer specimens are light blue (Latin, caelum, sky) or white. The strontianite of commerce is a massive mineral, more or less coarsely crystalline. The color varies with the impurities. Distinctive characteristics are effervescence with acids, density (3.68 to 3.71), and crimson strontium flame. A typical British celestite before World War II analyzed: SrSO4, 96.55 pct; SrCO3, 0.17; BaSO4, 0.25; CaSO4, 0.54; MgCO3, 0.15; R20,, 0.90; Si02, 1.38.10 A German strontianite analyzed: SrCO3, 90.9 pct; CaCO3, 7.5; BaCO3, 0.1; Fe2O3, 0.05; A1203, 0.1; SiO2, 0.04; S, 0.1; P, 0.005.10 ORIGIN AND MODE OF OCCURRENCE According to Clarke,9 strontia forms about 0.02 pct of the crust of the earth and is present in most igneous rocks, but in smaller quantities than barium. Under certain conditions, large masses of celestite are deposited from sea water with anhydrite. The presence of large amounts of celestite in some saline deposits and its absence in others suggests that the deposition of celestite depends on whether certain as yet undetermined concentrations of sulphate and chloride ions are reached in the brines. The most extensive of these sedimentary deposits are those of the Keuper (Triassic) in England, of the Zechstein (Permian) in Germany, and of various Cretaceous formations in Texas, Arkansas, and Utah. Of the deposits of southeastern California and western Arizona,

Jan 1, 1949

By George W. Sheary

Situated 45 miles west of Philadelphia and 50 miles southwest of Bethlehem Steel Company's Bethlehem plant, the integrated Grace mine facilities produce 4000 tpd of high-quality iron ore pellets. Startup of the Grace mill was in November 1958, and iron concentrates were shipped until March 1960, when the pellet plant went into operation. The underground mine, when fully developed, will hoist about 9000 tpd, including development rock. The crude ore, which has an iron content of approximately 42%, is magnetically cobbed and crushed in closed circuit with 3/4-in. slotted vibrating screens. The ore is washed and screened in the mill and the plus 1/4 in. screen product is again cobbed prior to feeding to the rod mills. Grinding is done in rod mills, and in ball mills that are in closed circuit with 30 in, cyclones, to 1% on 100 mesh and 65% minus 325 mesh. The ground ore is magnetically concentrated by three-drum permanent type finisher magnets to 67% Fe. The magnetite concentrate is pumped from the mill to a 50 ft thickener in the pellet plant. The thickened magnetite concentrate is relayed to the filters through a two-stage pump arrangement. The filter cake is fed by belt from filter concentrate bins to mixer-muller belts where it is intimately mixed with bentonite and a slight amount of water for moisture control. The fluffed concentrate then drops into balling cones. The green pellets from the balling cones are fed in a prescribed feed pattern to shaft furnaces through the use of shuttle car mechanisms. The green pellets are dried, heated to 2500°F and cooled to 1200°F as they descend through the furnace and into pellet coolers where the pellets are further reduced in temperature to 250°F. Heat is recovered in the cooling process through the use of air-to-air heat exchangers. The cooled pellets discharge on a rubber conveyor belt and are transferred to 6000-ton pellet railroad loading bin. The final pellet product consists of 90% plus 1/4 in. material (after tumble testing1) and contains 66% Fe plus 3% silica.

Jan 5, 1962

By John B. Mertie

MONAZITE formerly was described as moribund, but, in the light of recent developments, it is no longer so. It is the common source of the rare earths and thorium, both of which are becoming progressively important in industrial and other applications. Moreover, by the action of foreign governments, the sources on which the United States has depended for its supply are now either restricted or cut off entirely. Monazite has thus become a scarce mineral and processors in this country are endeavoring to acquire it from all available sources. RARE EARTHS AND THORIUM The rare earths proper, as defined by spectroscopists, are the oxides of cerium, praseodymium, neodymium, prometheum, samarium, europium, gadolinium, terbium, dysprosium, holmium, erbium, thulium, ytterbium and lutecium, with atomic numbers ranging respectively from 58 to 71. Chemists include with the rare earths scandium, yttrium, and lanthanum, with atomic numbers respectively of 21, 39, and 57. Thorium, with an atomic number of 90, is analogous to lanthanum, in that it precedes a second group of elements, whose oxides constitute the "rare earths of higher order." These are protactinium, uranium, neptunium, plutonium, americium and curium, with atomic numbers ranging respectively from 91 to 96. The last four mentioned are artificially prepared elements that so far have not been detected in nature. The rare earths with odd atomic numbers, except europium and lutecium, have no natural isotopes; and the two exceptions have only two isotopic forms. Those with even atomic numbers have from 4 to 7 natural isotopes. Samarium148 is radioactive, disintegrating over a half- life of 1.4 X 10 11 years with the emission of alpha rays. Lutecium176 is weakly radioactive, disintegrating over a half-life of 2.4 X 1010 years, with the emission of beta and gamma rays. At least 64 radioactive isotopes of the rare earths proper have been artificially prepared. Thorium is a strongly radioactive element, with a half-life of 1.39 x 1O10 years, which disintegrates through a series of 14 isotopes of 10 elements. The two longest lived and most important of these are

Jan 1, 1949

By W. E. Mitchell

The ore that is being treated by the present plant lies between the leached zone, or capping, and the mixed sulfide and oxide zone. The principal copper minerals are chalcanthite (CuS04.5H20), brochantite (CuSO4.3Cu (OH)2 and atacamite, (CuC12.3Cu (OH)2). There are, in addition, some other minerals such as cuprite and kröhnkite (CuS04. Na2S04.2H20). These minerals, with many others, occur in a greatly crushed granodiorite rock. most of the copper-bearing minerals occur in the cracks and veinlets, but there are disseminated values and it is probably the relative proportion of these that accounts for some otherwise unexplainable variations in extraction. The entire mineralization of the ore is complex and varies with depth. This variation, the problems presented thereby, and the effect of various constituents of the ore will be taken up in detail. An analysis of :in unweighted composite of the ore treated during 1927 follows: I'Lr Cent. Per Cent. Per Cent. Cu............... 1.58 S................. 2.10 Mo............ 0.01 SiO? ............. 66.10 HNO3 ........0.03 As............ 0.005 Fe.......... 1.41 C1 .............. 0.05 Sb............. 0.005 CnO ..... 0.20 Na................ 0.80 Ba............ 0.01 A1203 .......... 17.70 KI.............. 4.80 H20............ 0.70 mgO.............. 0.68 Mn............... 0.07 0 in sulfates. . . . 3.94 Total..... 100.19 The most important constituents of the ore, as indicated by experience to date, are: (1) The total copper content; (2) the acid-insoluble copper; (3) the acid-making copper mineral, mainly the chalcanthite; (4) the chlorine; (5) the nitrates; (6) the soluble iron; (7) the soluble molybdenum. The total copper content needs no discussion. In Table 1, the values are weighted averages calculated from individual charge analyses. The acid-insoluble copper directly affects the extraction, as the present leach recovers practically no acid-insoluble copper. In Table 1 the values are unweighted averages of the analyses of monthly composite samples. The acid-making copper mineral affects the amount of copper that can be dissolved from the ore without neutralizing acid in the solution. The

Jan 1, 1930

By Carville E. Sparks, Rollin Farmin

TRIAL installations of rock bolts, of the slit-rod-and-wedge type, were under way at several units of Day Mines, Inc., when Korean hostilities interrupted the already slow deliveries of steel bars to the Coeur d'Alene district. Factory-made bolts had not yet been put on the local market, so the program was halted for lack of supplies. Interest was revived by a visitor's description of wooden roof bolts. These were said to have been used briefly with apparent success in a coal mine, until apprehension voiced by the U. S. Bureau of Mines caused the practice to be suspended. To make wooden bolts for trial in ground support, Day Mines acquired a second-hand doweling machine equipped with two cutting heads, one to turn out the desired round rods of 2-in. diam, the other to turn out 1-in. rods to be used as powder-tamping sticks. This machine was installed in the all-weather sawmill of the Hercules mine unit at Burke, Idaho, where fabrication of the wooden bolts commenced early in 1951. Most of the mining in the Coeur d'Alene district is along steeply dipping veins in shaly quartzite and argillite of Algonkian age. Ground support commonly is required in zones where the rocks have been sheared, brecciated, and hydrothermally altered. Pressure from the sidewalls is more troublesome than weight overhead, but both increase with the size of the mine opening. Caving may come from a progressive sloughing of irregular rock fragments or from an exfoliation and buckling of the layered wall rocks. The disintegration is thought to develop from an initial elastic expansion of the rock toward the newly-created mine opening, followed by the dilation of many tiny partings in the rock by absorption of water. As the partings widen, masses of rock develop weight and become free to fall. The function of rock bolts is to prevent or retard widening of partings in the rock supported. Wooden Bolts, Wedges and Headboards Bolt assembly used by Day Mines consists of a bolt 4 or 6 ft long, two wedges 16 in. long, and a headboard 30 in. long, Fig. 1. All four pieces are made of local red (Douglas) fir, either green or well-soaked in the mill pond before it enters the sawmill. Bolts are fabricated from cants, 2 1/4 in. sq, cut from relatively straight-grained timber with a minimum of knots and trimmed to 4- and 6-ft lengths. The bolt then is turned in the doweling machine from 21/4 in. sq to 2 in. diam round, except for a 4-in. length at one end which is left full square to provide the striking head and the shoulder that holds the headboard in position for wedging. The foot end of the bolt is slit with a thin saw for a length of about 16 in., thereby making a slot to receive the wedge against which the bolt is driven for anchorage at the bottom of the rock hole. A similar slit, 12 in. long, is made in the opposite (head) end of the bolt to receive the second wedge, which crowds the headboard against the ground at the collar of the rock hole and puts the bolt in tension. The second slot is aligned 90" from the plane of the first slot to avoid Longitudinal splitting and is notched out slightly to allow easier insertion of the collar wedge after the bolt has been driven to bottom. To prevent splitting the headboard by spreading action of the head wedge, this slot is oriented at 90" to the grain of the headboard when the pieces are assembled, Fig. 2. The wedges are similar to standard mine wedges, but more slender; they are cut 1 7/8 in. wide and 1 in. thick at the heel and taper out in 16 in. of length. The headboard, or bearing plate, is not necessary for some types of ground but generally is desirable because it helps the bolt to support an area of loose, friable rock and reduces the tendency for the rock at the collar of the hole to split away from the wedged head by distributing the pressure over a wider rock surface. The headboard may be a 24-to 30-in. length of 3-in. plank, 8 to 12 in. wide, but a similar length of rounded sawmill slab serves equally well at 20 pct of the cost. A hole of 2-in. diam is bored or punched through the center of the headboard, either at 90" or at various high angles to its surface. The bolt is inserted to its shoulder through this hole, then driven into the rock hole. Bolts, wedges, and headboards are given a full timber preservative treatment to inhibit rot. Bundles of each are immersed in a warm saturated solution of Osmose salts in water for 48 hr, removed, dripped dry, and stored in a relatively humid underground depot to cure. Most wooden rock bolts used by Day Mines are 4 ft long. Holes to receive them, about 42 in deep and 2 1/8 in. in diam, are drilled into the rock' to be supported, nearly normal to the periphery of the mine opening. The type of drill used is dictated by convenience: stoper, jackleg, or jumbo-mounted drifter. Correct depth of the hole is assured by use of a measuring stick that has been cut to the proper distance from drill chuck to the ground at the collar of the hole when a standard length drill rod is at the bottom. The bolt is seated to the shoulder through the hole in the headboard, the foot-end wedge is placed in its slot, and the assembly is inserted into the rock hole. Then the bolt is driven until it is seated solidly on the wedge against the bottom of the rock hole. Driving may be by hand with a sledge, or

Jan 1, 1954

By D. S. Greig

There was a decline in the Italian oil production in 1933 and also in the footage drilled. A total of about 194,500 bbl. of crude oil was produced in the Emilia district of northern Italy from the same fields in production as in 1932. New drilling to the extent of 80,700 ft. failed to find new production to compensate for the decline in old wells, and no new fields were discovered in spite of an active exploration campaign by the government-owned company A.G.I.P., which has just completed the first year of a five-year exploration program. This company drilled a total of about 33,000 ft. The majority of its tests were drilled in the Po Valley upon locations selected by geophysical methods. This company is changing over to the rotary system for all future wells. It produced about 16,600 bbl. of oil from wells near Salsomaggiore and in the Po Valley. The Petroli d'Italia, which operates the old fields of Montechino, Valleja and Gratera south of Piacenza, has been doing normal development drilling in the endeavor to extend its present fields. Also it was drilling two exploration wells in the Torino district. It drilled a total of about 13,930 ft. and produced approximately 12,645 bbl. of very high-grade oil (specific gravity about 0.765). The Societa Petrolifera Italiana was occupied chiefly in exploratory drilling in the endeavor to extend its producing fields at Salsomaggiore and at Vallezza, south of Parma. It was also drilling one exploration well at Rile dell7Olio near Voghera on the line Milan-Genoa. It drilled a total of 33,849 ft. and obtained a production from its two fields of 165,273 bbl. It also produced 123,220 gal. of casinghead gasoline from Vallezza field absorption plant.

Jan 1, 1934

Discussion of the paper Of NOEL CUNNINGHAM, presented at the New York meeting, February, 1915, and printed in Bulletin No. 99, March, 1915, pp. 601 to 608. C. H. POIRIER, New York, N. Y. (communication to the Secretary*). -Mr. Cunningham's paper, written from the standpoint of a stamp advocate, while commenting more or less favorably upon the installation of ball mills in the Vipond plant, does not, in my opinion, give as much emphasis to the comparatively new departure as the installation of ball mills in the place of stamps justifies. This discussion is based upon my personal and intimate practical work for several years with stamp mills, and for the past three years with Hardinge ball and pebble mills. The fact that the Vipond mine contains about equal quantities of the A and B classes of ore mentioned by Air. Cunningham, and the further fact that I have had a most intimate knowledge of the working of both classes of ore in the Porcupine district in stamp mills and ball mills, justifies upholding my final decision to use ball mills in the place of stamps, and defends my present further action in now increasing the present Vipond capacity by the addition of another 6-ft. Hardinge ball mill, in which action the directors of my company concur. This is one of the strongest evidences I can possibly offer in substantiation of my opinion that the ball mill exceeds the efficiency of the stamp, both in metallurgical and mechanical economy. It is hardly fair to compare a 100-ton per clay plant with a mill handling several times this amount, yet it is my belief that the cost per ton. of grinding in the ball mill is far less than that of any stamp mill in the district, where capacities run up to 400 tons per clay.

Jan 5, 1915

Quarrying and crushing 500 tons of limestone plus burning some 240 tons of limestone per day are the two initial phases in the production of borax, soda ash, sodium sulfate and related chemicals at Stauffer Chemical Co.'s plant in Westend, Calif. These processing steps have been upgraded in recent years by the installation of new primary and secondary crushers, an 8 x 340-ft rotary kiln plus kiln feed, control and cooling components-all designed and manufactured by Traylor Engineering and Manufacturing Division of Fuller Co. As a result of this new equipment, a new product- quicklime-has been added to the West End product family and considerable reductions have been realized in fuel and manpower costs.

Jan 1, 1965

By Fred D. DeVaney

DURING the past few years a radically new process for the magnetic roasting of iron ores has been investigated and developed by Pickands Mather & Co. and the Erie Mining Co. in the Erie laboratory at Hibbing, Minn. This process, originally devised by Dr. P. H. Royster of Washington, D. C., involves the use of a roasting technique quite different from older methods. It has now been demonstrated that iron-bearing materials can be roasted as effectively as by any previously known method, and at a much lower cost. The increasing shortage of highgrade iron ores in this country has accelerated the search for new methods that would permit low grade materials to be utilized. The concept of magnetically roasting low grade nonmagnetic ores such as the oxidized taconites and then separating such material magnetically has always had considerable appeal. The magnetic concentration idea is attractive because of the sharpness of the separations and cheapness of the method. Heretofore, however, the equipment and the processes available for the magnetizing-roasting -step have left much to be desired. The customary equipment available for reduction roasting has been: 1-multiple hearth furnaces, 2-rotary kilns, and 3-shaft type kilns. In addition, it is understood that some work has been done in magnetically roasting fine ores by a process using the FluoSolids principle, but little information on this process is available. The multiple hearth kiln has been used the most but first costs and operating costs have been high because of low capacity, high maintenance, and poor gas utilization. Magnetic roasting can be done in a rotary kiln, but the radiation losses are high and the conversion to magnetite is usually unsatisfactory because of poor contact between the gases and the solids. Of the shaft-type furnaces, probably the most efficient yet developed is that designed by E. W. Davis of the Minnesota Mines Experiment Station. This furnace was operated at Cooley, Minn., during 1934-1937 but was abandoned in 1937 because the operation was uneconomic. Heretofore the basic concept behind most magnetic roasting processes has been the idea of heating iron ore to a temperature of 800° to 1100 °F in a strong reducing atmosphere, preferably either carbon monoxide or hydrogen. Temperatures under 800°F were undesirable since excessive roasting time was required. Temperatures over 1100°F were avoided because of the danger of converting part of the iron to ferrous oxide which is nonmagnetic. In the new roasting process, the operation is carried on in a shaft furnace using a controlled atmosphere containing a low percentage of reducing gas. The temperature in the roasting zone is considerably higher than with the usual reducing gas and this speeds up the reduction time. Portions of the spent furnace gases are cooled and recirculated and this together with the good contact between ore and gas makes for high reducing gas utilization. High heat economy is secured by recuperating heat from the roasted ore by passing the cold reducing gases countercurrent to flow of ore. The heat transfer principle is similar to that employed in a pebble stove and to that used in the Erie Mining Co. furnace at Aurora, Minn., for pelletizing fine magnetite concentrates derived from taconite. The theory of controlled atmosphere during the roasting operation can best be appreciated by inspecting the equilibrium diagram of the Fe-C-O system shown in Fig. 1. An inspection of this diagram shows that in certain areas magnetite, Fe3O4, is the only stable form of iron. A further inspection of this table shows that if the proper ratio is maintained between carbon dioxide to carbon monoxide, such a gas will be reducing with respect to hematite, Fe2O3, and will be oxidizing with respect to both ferrous oxide, FeO, and iron, Fe. It should be kept in mind that the formation of ferrous oxide in a roasting operation is harmful, since this oxide is nonmagnetic; if it forms in any quantity, it will cause substantial loss of iron in the ensuing magnetic separation step. If a ratio of approximately three parts carbon dioxide to one of carbon monoxide is maintained, the resulting operation can be carried on at a relatively high temperature without fear of over-reduction. Specifically, most of the tests in the Erie furnace have been made at a temperature of 1500° to 1600°F, with an entrant gas containing approximately 5 pct carbon monoxide and 15 pct carbon dioxide, with the remainder largely nitrogen. It should be remembered that the ratios of carbon monoxide to carbon dioxide shown in Fig. 1 hold even though the bulk of the gas is an inert gas such as nitrogen. It may surprise many to learn that a gas containing as low as 3 pct carbon monoxide, and 12 pct carbon dioxide with the remainder nitrogen is an extremely effective reducing gas in the 1000° to 1600°F temperature range. The reducing gas is not limited to carbon monoxide, and mixtures of hydrogen and carbon monoxide may be used effectively, provided that a similar ratio is maintained between the reducing gases and carbon dioxide and water vapor. For a more detailed explanation of the theory involved, the reader is referred to U. S. patents 2,528,552 and 2,528,553. From a safety standpoint, the weak reducing gas used in the furnace offers an advantage. Its composition is such that it is well below the limits of explosion should air enter a hot furnace. This condition is not true with the usual reducing furnace, in which a gas rich in carbon monoxide or hydrogen is used. The general furnace design and method of operation may best be understood by an inspection of

Jan 1, 1952

By Dwight M. Lemmon

Encouraged by increased demand and higher prices for such metals as copper, lead, zinc, silver and tin, search was pressed in 1964 for mineral raw materials, especially in parts of the world that are relatively more stable politically and economically. New discoveries of metallic ores continued to be made, discoveries based on extensive geologic and geophysical work but nonetheless made in part because of good fortune.

Jan 2, 1965

YEAR OF ELECTION 1913. FRANK DAWSON ADAMS, Montreal, Canada. 1921. WILLIAM CUTHBERT BLACKETT Sacriston, Durham, England. 1935. GUILLAUME DANIEL DELPRAT Melbourne, Vic., Aust. 1920. HENRY STURGIS DRINKER Merion Station, Pa. 1933. KARL EIKERS NEW YORK, N. Y. 1922. FEDERICO GIOLITTI Torino, Italy. 1906. SIR ROBERT A. HADFIELD London, England. 1928. JOHN HAYS HAMMOND New York, N. Y. 1921. FRANK WILLIAM HARBORD London, England. 1917. HERBERT HOOVER Washington, D. C. 1905. HENRI LECHATELIER Paris, France. 1931. WALDEMAR LINDGREN Cambridge, Mass. 1921. C. McDERMID London, England. 1913. EZEQUIEL ORDONEZ Mexico City, Mexico. 1935. ROBERT PEELE New York, N. Y. 1911. ROBERT H. RICHARDS Cambridge, Mass. 1934. T.A. RICKARD Victoria, B.C., Canada 1933. ALBERT SAUVER Cambridge, Mass.

Jan 1, 1936

By E. Brunner, G. L. Hassler, T. J. Deahl

The capillary effects in reservoir rock are discussed in terms of the pressures they cause in sandstones and dolomites. Data for the two-phase case (oil-gas or water-gas) and for the three-phase case (oil, water and gas in rock) are used to demonstrate that in one sense the wetting preference of a rock depends on its saturation. The nature of capillary hysteresis is described for partially stable conditions, and the concept is enlarged. Reproducibly measurable pressures include the "capillary pressure," which is the pressure difference between any two phases that are each interconnected; the "threshold pressure," necessary to force a nonwetting phase through partially saturated rock; the "displacement pressure," which is that special case of the threshold pressure in which both phases fully saturate separate portions of the rock. Displacement pressure is equal to the minimum value of the "capillary pressure." The theory of flow including capillary forces is developed at the producing surface of a well to reveal the presence there of a pressure discontinuity in the gas (or other nonwetting) phase that can be controlled to the end that more oil may be poduced from an oil field. Experiments with packed sand-flow tubes having artificial producing surfaces support the theory. Introduction The basic surface quantities acting in an oil field are two: namely, surface tensions and contact angles. These are the quantities, variously expressed, and particularized as spreading forces, adhesion tensions, heats of wetting, etc., which are measured in the laboratory by techniques mostly confined to flat or circularly cylindrical surfaces. Such measurements have not had the extensive engineering application they seem to deserve because in most practical cases they are unavoidably compounded with the complex and unapproached subject of the internal shape of the interstices of rock. In this paper it is intended that the pressure differences developed in rock by capillarity be examined, defined, and given some engineering use in terms of some new measurements that have been made. Such pressure differences—namely, the capillary pressure, the displacement pressure and the threshold pressure—seem to provide a proper contact between the basic molecular quantities and the oil field. While certain modifications of usage will be undertaken, the present effort rests upon the background of work by the U. S. Geological Survey,l by Versluys, and especially by W. 0. Smith, 3,4,5 which has been reviewed recently in papers by Leverett.=s7 The most important concept of pressure difference is the capillary pressure, a function of saturation that expresses the pressure difference between the interconnected phases in a rock. It is often measured when water and air are the fluids present, but it can be measured with other fluids. A number of curves of capillary pressure have recently been measured by a method which it is intended shall be published in a later paper. Since heretofore capillary-pressure measurements upon rock have not been

Jan 1, 1944

By G. L. Hassler, E. Brunner, T. J. Deahl

The capillary effects in reservoir rock are discussed in terms of the pressures they cause in sandstones and dolomites. Data for the two-phase case (oil-gas or water-gas) and for the three-phase case (oil, water and gas in rock) are used to demonstrate that in one sense the wetting preference of a rock depends on its saturation. The nature of capillary hysteresis is described for partially stable conditions, and the concept is enlarged. Reproducibly measurable pressures include the "capillary pressure," which is the pressure difference between any two phases that are each interconnected; the "threshold pressure," necessary to force a nonwetting phase through partially saturated rock; the "displacement pressure," which is that special case of the threshold pressure in which both phases fully saturate separate portions of the rock. Displacement pressure is equal to the minimum value of the "capillary pressure." The theory of flow including capillary forces is developed at the producing surface of a well to reveal the presence there of a pressure discontinuity in the gas (or other nonwetting) phase that can be controlled to the end that more oil may be poduced from an oil field. Experiments with packed sand-flow tubes having artificial producing surfaces support the theory. Introduction The basic surface quantities acting in an oil field are two: namely, surface tensions and contact angles. These are the quantities, variously expressed, and particularized as spreading forces, adhesion tensions, heats of wetting, etc., which are measured in the laboratory by techniques mostly confined to flat or circularly cylindrical surfaces. Such measurements have not had the extensive engineering application they seem to deserve because in most practical cases they are unavoidably compounded with the complex and unapproached subject of the internal shape of the interstices of rock. In this paper it is intended that the pressure differences developed in rock by capillarity be examined, defined, and given some engineering use in terms of some new measurements that have been made. Such pressure differences—namely, the capillary pressure, the displacement pressure and the threshold pressure—seem to provide a proper contact between the basic molecular quantities and the oil field. While certain modifications of usage will be undertaken, the present effort rests upon the background of work by the U. S. Geological Survey,l by Versluys, and especially by W. 0. Smith, 3,4,5 which has been reviewed recently in papers by Leverett.=s7 The most important concept of pressure difference is the capillary pressure, a function of saturation that expresses the pressure difference between the interconnected phases in a rock. It is often measured when water and air are the fluids present, but it can be measured with other fluids. A number of curves of capillary pressure have recently been measured by a method which it is intended shall be published in a later paper. Since heretofore capillary-pressure measurements upon rock have not been

Jan 1, 1944

By C. Williams, D. V. Carter

During 1943 five oil fields and two gas-condensate fields were discovered in the East and East Central Texas district. The New Hope field, discovered by Tide Water-Seaboard in Franklin County, is the most important oil discovery since the Hawkins field in 1940. At the close of the year two oil sands were producing and two additional oil sands were being tested. The gas-condensate fields of Appleby in Nacog-doches County and the Stewards Mill field in Freestone County had only one producing well each. The Carthage field was extended 3 miles north and 4 miles west. Another well that was testing at the year end indicated a probable eastward extension of several miles. The Quitman field, in Wood County, was the most active from the standpoint of drilling operations. Approximately 48 wells were complcted during the year. The second and third most active fields were Hawkins field, Wood County, and Kildare field, Cass County, respectively. Wartime restrictions of material, together with manpower shortage and Federal spacing regulations, reduced the number of oil and gas-well completions from 265 in I942 to 171 in 1943. This represents a drop of 35 percent, or approximately 1/3, enough to replace the 531 producing wells abandoned in the district during the year. No changes were made in the price of crude oil in the district in 1943. The district produced 177,652,940 bbl. of condensate and oil during 1943. This represents an increase of approximately 11 per cent compared with the previous year. The East Texas field, which is the largest and most important field in the district, had an annual production of 128,568,647 bbl. of oil, which is approximately 6.5 per cent more than the previous year, and represents 72 per cent of the district's production of condensate and oil for the year. The district had an estimated basic daily allowable of approximately 509,000 bbl. of oil on Dec. 31, 1943. The entire district produced approximately 30 pcr cent of the state's production for the year 1943. The Hawkins field, Wood County, was operated 271 days during the year and with an average daily production of approximately 52,488 bbl. for the year. This field, which is the second largest in the district, produced 14,224,164 bbl, of oil during the year. Changes in annual production in certain fields in the district can be attributed to their ability to produce at higher rates, the demand, and transportation facilities in the war effort. The East Texas field showed an over-all decrease in reservoir pressure of 8.30 lb. during the year. Indications were that through the first quarter of 1944 the return of salt water to the reservoir was having a beneficial effect. It is hoped that, as more and more water is returned to the reser-

Jan 1, 1944