Search Documents

By E. W. Dewing

The solubility of A14C3 in cryolite melts has been determined by holding the melt with aluminum in a graphite crucible for 4 hr at temperature, quenching the crucible in water, and analyzing the frozen salt by CH4 evolution. The solubility is given by log(wt % Al4C3) = 1.298 -1.l74 (wt ratio NaF/AlF3) independent of temperature in the range 985" to 1080°C. Additions ofA1203, .NaCl, CaF2, or LiF up to 10 wt pct do not affect the solubility, provided that LiF and CaF2 are replaced by equivalent NaFin calculating the ratio. The variation with ratio can be accounted for quantitatively on the hypothesis that the Mechanism of solution is Al4C3 + 2AIF3 = 3Al2CF2 since the solubility varies as (aAIF3) 2/3; Mechanisms involving C", C2- , AlC- , A12C2+, and Al2CF+are re-jected. At ratios above 1.5 truces of c;- are also present. It was noticed some years ago in this laboratory that carbon specimens made cathodic in a cryolite bath decrease in diameter over a period of time.' It was also found that cryolite which had been melted with aluminum in a graphite crucible was sometimes yellow, and that A14C3 could be seen intimately embedded in the cryolite crystals. CH, could be recovered by acid attack. There was thus reason to believe that A14C3 had a genuine solubility in molten cryolite, and the object of this work was to measure it. EXPERIMENTAL AND RESULTS A graphite crucible, 2 in. ID and 2.5 in. deep with a close-fitting lid, contained about 150 g of cryolite (plus additives) and about 20 g of 99.99 pct pure Al. It was placed in a vertical Inconel furnace tube, covered with refractory brick to provide thermal insulation, and the top of the tube was roughly sealed with disks of asbestos paper. An alumina tube led argon down to the level of the top of the crucible to expel air, and an alumina sheath with a Pt-10 pct Rh ther-mocouple inside was positioned between the crucible and the wall of the Inconel tube. The tube was heated in an electrical resistance furnace for the desired length of time; the refractory bricks were then removed, and the crucible was lifted out with tongs and quenched in water. After such a crucible was broken open it could be seen that its inner surface was yellow owing to the presence of A1,C3, and sometimes needle-like crystals could be observed (at X75 magnification) growing out into the nielt. It was concluded that Al,C, had been present as a separate phase when the crucible was at tenlperature and that the melt had been saturated: in

Jan 1, 1970

By Stanley Gill

The apparatus is composed of sections of small diameter, seamless steel tubing welded into a continuous flexible tube. At the bottom end a 1/4-in. pipe nipple with a 10 to 15-lb. weight is attached, together with a registering thermometer and a pair of ball check valves. The entire length of tubing is coiled in a single layer upon a drum 4 ft. in diameter which can be attached to the platform of a truck and provided with devices for winding and unwinding the tubing. Connections are made with the upper end of the tubing through a stuffing box, thence to a gas manifold to which a pressure gage is connected. Hydrogen gas is carried in standard 2-ft. cylinders and readings are taken by admitting gas into the tubing from one (or both) of the hydrogen cylinders until the pressure has been built up above that to be measured. At this time the gas supply is cut off. Excess gas escapes through the open end of the tubing and when equilibrium is reached, the pressure is read at the surface gage. Corrections are made for the weight of the column of gas. The advantages claimed for the apparatus include accuracy and the ability to measure the pressures at any number of points without removing the gage. Among the disadvantages of the apparatus are the somewhat bulky size of the equipment and its relatively high initial cost.

Jan 1, 1933

By F. N. Rhines, B. H. Alexander

MUCH attention has been directed to the effects of grain size upon the properties of alloys, but there has been scant study either of the conditions that determine the pattern and dimensions of den-drites in metal systems, or of the influence of their shape and size upon the overall properties of cast-ings. The aim of the research that is about to be described has been to investigate the effect of vari-ous factors upon the mode of formation of dendrites in alloys by measurements of the distance between adjacent dendrite arms (dendrite spacing). Early investigators, including Grignonl and Tschernoff,2 showed that a metal dendrite is com-posed of a tree-like system of stalks and branches arranged in a simple geometrical pattern. North-cott and Thomas3 demonstrated that, in the face-centered cubic solid solutions of copper-base, these stalks and side arms all lie in (100) directions in the crystal. Several investigators, including Sauveur and Chou,0 Sauveur and Reed,' and Martin and Mar-tina have reported that the addition to steel of alloy-ing elements, such as nickel, chromium, and molybdenum, not only makes the dendrites easier to reveal by etching, but makes them coarser. The latter authors8 proposed that the coarsening of the dendrites is roughly proportional to the increase in the temperature range of freezing, caused by adding the alloying elements. Sauveur and Chou6 showed, in addition, that the dendrites are coarsened by a decreased rate of cooling of the casting. Measurement of Dendrite Arm Spacing Among the physical conditions that could be ex-pected to have an influence upon the dendrite arm spacing, that appears in a cast metal, are: composi-tion, rate of freezing, crystal structure, and type of constitution. The relationships obtaining between these variables and the dendrite dimensions have been examined, in the present research, by measur- ing the arm spacing in a wide variety of alloys, listed in tables II through VI. Alloy compositions are recorded in the tables by showing the symbol of the major metal followed by the percentage and symbol of the alloying agent; thus, "Al-10Ag" is an aluminum-base alloy containing 10 pct of silver. Although none of the alloys were analyzed, an im-pression of their degree of purity may be obtained from that of their component metals given in table I. Five hundred grams of each alloy was made by melting in small clay-graphite crucibles in an elec-tric muffle furnace. After alloying the temperature was adjusted to 50" to 75°C above the liquidus and the melts were poured into cast iron molds, at room temperature, the molds having a wall thickness of 1 in. and a cavity 11/2 in. sq in cross-section. Each ingot, thus cast, was sectioned at mid-height and the sectioned surface was polished and etched for metallographic examination. Dendrite spacing meas-urements were made at three positions, namely, ad-jacent to the mold wall, midway between the wall and the center of the ingot, and at the center (desig-nated e, m, and c respectively, in the tables). A typical series of microstructures is presented in fig. 1. For each measurement, the average was taken of the dendrite spacing of several grains covering a zone about 2 mm wide. Only those grains which had a major dendrite axis nearly in the plane of polish were selected in order to eliminate corrections for orientation differences from grain to grain. Although the dendrite spacings were measured to the nearest thousandth of a millimeter, the values listed in the tables are thought to be significant only to the nearest hundredth of a millimeter. The larg-est difference in readings found, when various ob-servers rated the same specimens, was 0.012 mm; the largest difference between corresponding meas-urements upon duplicate specimens was 0.027 mm.

Jan 1, 1951

By James S. Foster, Paul G. Shewmon, Frank V. Nolfi

Analytical expressions are developed for the kinetics of dissolution or growth of a spheroidized, solute rich stoichiometric Precipitate in the surrounding matrix. There are two limiting cases; in one the rate of dissolution or growth is limited by long range solute diffusion through the matrix and in the other by the transfer of atoms across the mrdrix-precipitate interface. In the former case local interfacial equilibrium exists while in the latter it does not and the rate of dissolution or growth is controlled by an interfacial reaction. The analysis treats both limiting cases as well as mixed control in a single development, where it is found that the thermodynamic state of the interface is completely specified by a single parameter, o, defined by where K is the reaction rate constant, D is the matrix solute diffusivity, and R, is the precipitate radiz~s. If K is infinite then a is zero and local equilibrium prevails; if K deviates infinitesimally from zero, then a is very near unity and an interfacial reaction is rate controlling. Mixed control occurs for intermediate values of o. From the analytical results, numbers are computed which are useful in determining the duration of interfacial reaction or mixed control; following this time period, long range diffusion is rate controlling. THE rate controlling process or processes governing phase boundary migration has been the subject of much speculation and investigation. Traditionally, the most widely assumed boundary condition in quantitative treatments of this problem has been that of local interfacial equilibrium. This condition implies that long range diffusion of one or more elements controls the migration and is referred to as "diffusion controlled migration" (herein DCM). In contrast to the above view is the proposition that local interfacial equilibrium does not exist and that transport of atoms across the interface is rate controlling. Consequently, this mechanism is referred to as "interface controlled migration" (herein ICM). In processes of the latter type, the activity, a, of one or more elements is discontinuous at the phase bound- ary and the flux, J, across the boundary of a given element is some function of its activity discontinuity, a. One of the most comprehensive contributions to a mathematical description of phase boundary migration is due to am.' His analyses are applicable to precipitation in binary systems in which a) the precipitates are spherical* solute rich compounds of constant

Jan 1, 1970

By S. D. Baumer, P. M. Hulme

B. M. Larsen (U. S. Steel Co., Kearny, N. J.)—Could we have some sort of an estimate on the cost of calcium carbide for this treatment? Also, if you used calcium carbide on carbon-saturated iron, would some effect hold back the reaction? P. M. Hulme (authors' reply)—As far as I know we have not worked on carbon-saturated iron. About 3½ pct C is the highest we have worked on. As far as cost goes, it depends on how much sulphur You have to take out. It will run anywhere from $0.75 to $2.00 a ton overall cost including the cost of carbide per ton of metal treated. That is, using the efficiencies that we show in this paper. We are getting better efficiencies now. T. L. Joseph (University of Minnesota, Minneapolis, Minn.)—Did you say 2 lb of calcium compound? Mr. Hulme—That is based on 10 lb of calcium carbide per lb of sulphur removed. D. E. Babcock (Republic Steel Corp., Youngstown, Ohio)—We have run this type of desulphurization process at the blast furnace. We have desulphurized between 100 and 200 at the blast furnace and taken the iron right out of the furnace with an injector system. The process gave us quite varied results; stratified iron, high sulphur on the top and low sulphur on the bottom, and we decided it was impractical. Mr. Hulme Just what was the type of injection equipment? Dr. Babcock—Nitrogen gas for one injection method and we used fairly large gun equipment. We followed the same general type of pattern you show only on a larger scale. Mr. Hulme—It sounds very much like what we call the gale of wind method. We have very erratic results with that. Dr. Babcock—We have tried several types, and particle sizes. The operation was not satisfactory. Mr. Hulme—Of course, we have never tried it on that scale except on a continuous basis. That is the reason we abandoned the idea of working on 35 ton ladles on a batch principle and took it as it came out of the cupola and treated it on the fly on a continuous basis. Dr. Babcock—When you compare the relative effectiveness of the process as carried out, it does not give a very favorable comparison of that process which is already developed. We did not feel it was worth the

Jan 1, 1952

By T. A. Rickard

In a previous paper (ante, p. 411) some description was given of the occurrence of the auriferous alluvium, extensive deposits of which lie among the highlands of the province of Otago, New Zealand. The present paper will describe some of the methods by which that alluvium is exploited. The alluvial mining of New Zealand is not yet hindered by " debris legislation." The mines are for the most part situated in a country of little agricultural value, and large rivers with rapid currents act as tailings conveyors. In time, however, steps will have to be taken to restrict the discharge into the Clutha of the tailings which are slowly raising the river-bottom. The methods of California have been followed in Otago with such alterations as peculiar local conditions require. The distinctive feature of the alluvial mining of Otago is the prominence given to the hydraulic elevator. The all-important factor in this form of mining is the control of an abundant water-supply at a suitable height above the level where it is to be utilized; and in this respect the gold-fields of the south island of New Zealand are most favora-

Jan 1, 1893

By G. Mempel, D. C. Yang, D. W. Fuerstenau

This paper describes details of the design and operation of a batch tumbling mill which has been used for a number of years in the laboratories at the University of California. In order that the energy expended for grinding can be measured accurately, this specially constructed laboratory mill has sensitive torque measuring apparatus. Torque measurements are given for a variety of conditions with this particular mill. In recent years, there have been numerous and fairly extensive investigations of grinding in tumbling mills reported in the literature. Most of these investigations have been carried out in mills with widely differing dimensions. As a result, comparison of results obtained from various investigations has been virtually impossible. If similar mills were used by different investigators, a considerable step forward would be taken in grinding research. A specially constructed laboratory mill with sensitive torque measuring apparatus has been used for a number of years in the laboratories of the University of California. The purpose of this paper is to describe details of the design and operation of this batch tumbling mill so that other researchers, who might be interested in obtaining data for intercomparison, could construct a similar device for their own research. Furthermore, since torque instrumentation is quite expensive, torque measurements are given for a variety of conditions with this particular mill so that those who may not wish to duplicate torque measuring apparatus can make reasonably accurate torque estimates merely by duplicating the loading conditions. It is not intended in this paper to present theoretical derivations of energy consumption in ball mills. This has been done e1sewhere.l-3 CONSTRUCTION OF THE MILL In order to eliminate rust problems with wet grinding, the mill and grinding media are made of stainless steel. The mill shell was rolled from 1/2-in. steel plate. The inside dimensions are 10-in. diam and 11-1/2-in. length, similar to the mill used by Charles.4 It is equipped with eight lifter bars (1/4-in. in height) whose dimensions are given in Fig. 1. The lifter bars have been bolted into the shell so they can be removed for experiments without lifter bars; however, all data presented here are for the mill with lifters. One end of the mill is fitted with two 1/2-in. diam removable plugs for filling the mill with liquid for wet grinding experiments. The mill is mounted on ball bearing rollers as can be seen in Fig. 2. The pillow block bearings are single-row self-aligning sealed ball bearings with 1-1/4 in. hole diam. The bearings supporting the mill shell are single row sealed ball bearings with

Jan 1, 1968

By James H. Bechtold

The yield strength of annealed tungsten was found to have a strain rate exponent 12 times as great as that of low carbon steel. The effects of temperature and strain rate could be correlated through the Zener-Hollomon parameter with a heat of activation associated with yielding of 32,000 cal per g-atom. This heat of activation is independent of strain although both the temperature and strain rate dependence of the yield strength vary with strain. MOST metals have mechanical properties that are relatively insensitive to strain rate, especially at temperatures below that at which creep is important. In iron and molybdenum," however, relatively large strain rate effects are observed in the temperature range where the rapid increase in yield strength occurs which leads to the ductile to brittle transition. In this temperature range Zener and Hollomon' have suggested that the effects of strain rate and temperature T on the yield strength could be correlated through a single parameter, P, in the following manner where Q is a heat of activation characteristic of the metal and associated with some unspecified relaxation process. They also observed that if the temperature is restricted to a relatively narrow range— below room temperature for steel—that the logarithm of the yield strength could be expressed as a linear function of the logarithm of P. From this relation the logarithm of stress should be a linear function of the logarithm of the strain rate at constant temperature: where r will be referred to herein as the strain rate exponent. At a constant strain rate the logarithm of stress should be a linear function of l/T, ay(e = C) ~ eT [4] where q = Qr [5] and is referred to herein as the temperature exponent. These equations have been found to relate the effects of temperature and strain rate on the yield strength of molybdenum in the temperature range wherein the ductile to brittle transition occurs, —75° to +150°C.2 Bechtold and Shewmon3 have shown recently that the ductile to brittle transition in annealed tungsten occurs in the temperature range +150° to +350°C. In this temperature range the yield strength in-

Jan 1, 1957

By R. M. Daelen

In recent years many new appliances have been introduced into German steel-works and rolling-mills for the purpose of improving working-methods, and of creating and maintaining increased production, and satisfying the ever-growing demand for metal of closely specified hardness, strength and form. One result of the improvements has been to aid very effectively in demonstrating the real superiority of ingot- over wrought-iron for almost every possible purpose, and in dispelling the last vestiges of prejudice unfavorable to the new metal. If, nevertheless, no marked decrease in the number of puddlingfurnaces has yet been noticed, the cause of their survival must be attributed to the greatly increased consumption of all kinds of ironmanufactures. Several large new works for the production of ingotiron are now, however, in course of erection in the Rhenish-Westphalian district, and upon their completion a rapidly diminishing output of wrought-iron may be anticipated. The present aim of all large works manufacturing ingot-iron is to work the molten blast-furnace pig into a finished product without any further fuel-consumption than is required to furnish steam for the rolling-mill. Though practice has established the feasibility of this principle, no works can yet point to its complete adoption, partly because of the limitations imposed by existing conditions and plant, and partly, also, on account of the highly-diversified character of the finished products. The Bessemer-works were the first to feel the influence of the basic process; but of recent years a similar influence has affected the open-hearth, and the owners of works possessing both a converterand an open-hearth plant are now seeking to arrange them for combined working, in charging as well as in casting. In small works the basic-lined reverberatory furnace is constantly gaining ground over the old puddling-furnace. The small basic converter, on the

Jan 1, 1891

By H. M. Morse

Tinsley Oil Field.—Mississippi joined the oil-producing states when on Sept. 13, 1939, the Union Producing Company's G. C. Woodruff well No. 1, sec. 13, T. 10 N., R. 3 W., Yazoo County, was completed after drilling plug at 4540 ft. in the Woodruff sand of the Eutaw formation of Cretaceous, producing 300 bbl. per day of 34.4" gravity oil through a ¼-in. choke, with a gas-oil ratio of 80 to 1 and bottom-hole pressure of 2045 lb. This was the discovery well in the Tinsley oil field. The well was drilled to a total depth of 4567 ft. and no salt water was encountered. The sand underlies the Selma chalk formation. Nine producing oil wells and one dry hole were drilled and completed by the end of 1939. Two producing sands have been found in the Eutaw and a third sand in the top of the Tuscaloosa formation, called the Woodbine sand in Louisiana and Texas. Faulting is an important factor in the Tinsley field. Total oil production has been approximately 250,000 bbl. from the nine flowing wells. Total depth to top of productive zone was 4540 ft.; to bottoms of productive wells, 4580 ft. Net thickness of the producing formation is 20 to 40 ft., and its porosity is 24 per cent. The deepest zone tested was the Tuscaloosa, in which the depth of hole was 6112 feet. Six hundred and forty acres has been proved for oil production. Jackson Gas Field.—The Jackson gas field has shown a steady decline in the number of wells but the pressure has been maintained. This field is a perfect example of a water-driven field and the time of wells going to salt water is predictable. Five wells were drilled in the Jackson field, of which only one produced. Amory Gas Field.—Interest was renewed in the Amory gas field, where a new well was started in the fall of 1939. Geological Formations.—The deepest well drilled in 1939 was the Willmut Gas and Oil Company's Cleve Love S. F. Johnson No. 1, sec. 29, T. 6 N., R. 1 W., Hinds County. This well encountered the Lower Cretaceous, Trinity series from 3770 to 6422 ft.; Lower Mesozoic from 6422 to 6484 ft. The geological correlations and nomenclature of the formations in Mississippi are shown in the accompanying strati-graphic section.

Jan 1, 1940

By H. M. Morse

Tinsley Oil Field.—Mississippi joined the oil-producing states when on Sept. 13, 1939, the Union Producing Company's G. C. Woodruff well No. 1, sec. 13, T. 10 N., R. 3 W., Yazoo County, was completed after drilling plug at 4540 ft. in the Woodruff sand of the Eutaw formation of Cretaceous, producing 300 bbl. per day of 34.4" gravity oil through a ¼-in. choke, with a gas-oil ratio of 80 to 1 and bottom-hole pressure of 2045 lb. This was the discovery well in the Tinsley oil field. The well was drilled to a total depth of 4567 ft. and no salt water was encountered. The sand underlies the Selma chalk formation. Nine producing oil wells and one dry hole were drilled and completed by the end of 1939. Two producing sands have been found in the Eutaw and a third sand in the top of the Tuscaloosa formation, called the Woodbine sand in Louisiana and Texas. Faulting is an important factor in the Tinsley field. Total oil production has been approximately 250,000 bbl. from the nine flowing wells. Total depth to top of productive zone was 4540 ft.; to bottoms of productive wells, 4580 ft. Net thickness of the producing formation is 20 to 40 ft., and its porosity is 24 per cent. The deepest zone tested was the Tuscaloosa, in which the depth of hole was 6112 feet. Six hundred and forty acres has been proved for oil production. Jackson Gas Field.—The Jackson gas field has shown a steady decline in the number of wells but the pressure has been maintained. This field is a perfect example of a water-driven field and the time of wells going to salt water is predictable. Five wells were drilled in the Jackson field, of which only one produced. Amory Gas Field.—Interest was renewed in the Amory gas field, where a new well was started in the fall of 1939. Geological Formations.—The deepest well drilled in 1939 was the Willmut Gas and Oil Company's Cleve Love S. F. Johnson No. 1, sec. 29, T. 6 N., R. 1 W., Hinds County. This well encountered the Lower Cretaceous, Trinity series from 3770 to 6422 ft.; Lower Mesozoic from 6422 to 6484 ft. The geological correlations and nomenclature of the formations in Mississippi are shown in the accompanying strati-graphic section.

Jan 1, 1940

By Earl C. Willis

In selecting new or replacement mining machinery to be purchased, there are many considerations to be discussed and taken into account, the most important being the productivity of the machine and the maintenance cost and downtime to be expected with the new equipment. Productivity of a given mining machine is evaluated by the Industrial Engineering Department: analysis of potential upkeep and downtime calls for the Maintenance Department to enter into the task of evaluating new mining machines. This is a very important function of the maintenance department because a wrong decision or mistake in judgment, particularly in a commercial mining company, can be exceedingly expensive. Once the type and size of a machine is decided, an examination of units fitting the basic requirements will sometimes show one particular machine which has a distinct edge on the competitive machine. In this case, the decision is easy. However, in most cases, the performances of the machines being considered are so close that the decision becomes one that is very difficult to make on performance alone. Serious consideration must then be given to maintenance performances and features of the machine which would permit lower maintenance and less downtime.

Jan 7, 1963

By F. T. Davis

The annual review of mineral dressing was the subject of considerable discussion at the MBD meeting in New York last February. Because the amount of material now being published is so imposing, it was generally agreed that reviewers should try only to cite the items of importance. In order to conserve even more space, it was agreed to omit bibliographies. In reading these reviews, and those of the past two or three years, one is impressed by the advances in materials handling, the enlargement and the advances in automation of unit process equipment. Although there has been development of a variety of new concentration principles in flotation, magnetic separation, et al., the design of these principles into new plants has not been widespread. The probable reason is that the plants being built today are so large and costly that few are able to face the risk of any significant degree of experimentation. There are exceptions to this; for example, some of the chemical processes, but these are usually because there was no conventional process available. This situation should change in time as the ores amenable to our conventional methods become depleted.

Jan 2, 1967

By S. Fisher Morris

The New River coal-field embraces that portion of the Appalachian coal formation which lies on the waters of the New River, principally in Fayette and Raleigh counties, West Virginia, covering a strip of territory about forty miles in length along the line of the Chesapeake and Ohio Railroad from Quinnimont to Kanawha Falls, where the New River empties into the Kanawha, the railroad following the banks of the river the whole distance. (See map.) Between Kanawha Falls and the Valley of the Ohio lies the great Kanawha region, and these two coal-fields possess a greater variety of coal than can be found in any other portion of the country, enabling them to furnish the best fuels for any of the various demands of manufacture or domestic use, the Kanawha region possessing many varieties of gas, hard splint, and cannel coal, and the New River region bituminous and semi-bitnminous, steam and coking coal. The New River, in its westward course towards the Kanawha, has cut its way entirely through the Sera1 conglomerate or No. XII of the Pennsylvania Reports, the Umbral red shales of No. XI appearing at the foot of the mountains at the eastern end of the region at Quinnimont, one of the upper ledges of the Conglomerate forming the summits; while at the western end, at Kanawha Falls, the top of the Conglomerate is nearly down to the level of the river, a portion of the " Lower Productive Measures" forming the greater portion of the mountains. These mountains rise abruptly from the banks of the river to a height of from 800 to 1200 feet, leaving only here and there narrow strips of bottom land, a few acres in extent; and as the measures consist principally of hard sandstones, shales, and conglomerates lying ill a nearly horizontal position, the mountain-sides are very precipitous, with many long and high cliffs, which, with the great height of the mountains, give the country a very rugged appearance. Along the sides of these mountains fronting on the New River and its many tributaries there are exposed the outcroppings of several veins of bituminous and. semi-bituminous coal, varying in thickness from a few inches to over four feet, five of them being workable, or

Jan 1, 1880

By Barry S. Siegal

Spectral reflectance data in the wavelength region of 0.45 to 2.4 µm have been obtained for various rock types and different forms of natural vegetation by means of JPL's portable field reflectance spectrometer. Computer analysis of these data has demonstrated the importance of obtaining remotely sensed spectral data beyond the wave- length region sensed by Landsat. Computer processing techniques have been developed and used for the analysis of these data and their application to a variety of geologic problems.

Jan 1, 1977

By William J. Potter

The current financial environment differs markedly from past commodity price expansions, which have benefited the mining industry. Deregulation, financial innovation, and the globalization of capital markets in the 1980s have altered financing and investing patterns. Investment bankers and smart money within the industry have recognized the alterations and trends that facilitate fee revenue and profitable growth. This paper profiles transactions exemplifying change and documents financing techniques or instruments that have developed during the past half decade, emphasizing equity in the global marketplace.

Jan 1, 1990

C. W. GOODALE, Butte, Mont. (member of the committee)- (communication to the Secretary*).-In the discussion of papers presented at the New York meeting of the Institute in February, 1915, and at the Arizona meeting of September, 1916, I referred to the activities of the Bureau of Safety of the Anaconda Copper Mining Co., and I am now submitting a few thoughts by members of the staff of that Bureau. TORGUS H. OAAS, Safety Engineer, Butte, Mont.-The report of the Committee on Safety and Sanitation has described different organizations and methods of promoting safety work. The effectiveness of these methods would aid the beginner in his campaign for safety in choosing the kind of organization and methods best adapted for his field. This can he obtained only by a discussion by those who have long promoted this kind of work, and have met with successful results. As the field is new, the different organizations promoting safety work have not established a common basis of rating for their fatal, serious and slight accidents, so that it is now difficult to get a comparative basis from which to judge the merits of the different systems. C. W. GOODALE.-The U. S. Bureau of Mines adopted, at the beginning, as a basis for its yearly summaries, the number of accidents. per 1,000 men employed, and it is now (quoting from its report for 1915, Technical Paper 168) making the following "classification of injuries:" "Many of the States now have. compensation laws, and in order to conform with their classifications, the bureau's classification of serious and slight injuries for 1915 is on a 14-day (2-week) basis instead of 20 days, as in previous years. The new classification of injuries includes three types, as follows: 1. Fatal 2. Serious (time lost, more than 14 days) (a) Permanent disability Total Partial

Jan 6, 1917

By H. Rosenthal, A. L. Jamieson

THE action of mercury on stressed brass to produce cracks was known before Moore, Beckinsale and Mallinson1 showed that actual season cracking did not occur spontaneously but could be induced by ammonia. These investigators studied other substances, including diphenylamine, without finding that anything other than ammonia could cause season cracking. Grimston2 reported season cracking in cartridge cases stored in wooden boxes wetted with dilute sulphuric acid pickling solution. Season cracking associated with sulphur dioxide, water vapor and air has been reported by Johnston,3 although he reported that trimethylamine and pyridine did not cause cracking. Jevons4 has ascribed season cracking of brass in certain instances to trimethylamine, "aldehyde amine," "ketone amine" and pyridine, but no experimental work was done evidently to prove this definitely. Pyridine was investigated by Morris,' who found it to have considerable cracking power. In the present investigation, the object was a qualitative evaluation of a number of representative amines with respect to their ability to cause season cracking. Thus it was desired only that an appreciable vapor pressure of each amine be obtained in order to make the test as severe as possible, without attempting to test equivalent concentrations for comparative purposes. METHODS Specimens Two types of specimen were used: I. Unannealed 70-30 brass cups formed from 0.040-in. thick sheet. Height of cup was 1 3/8 in. and diameter was 1 7/8 inches. 2. First draw pieces of caliber .50 cartridge cases in the unannealed condition (70-30 brass). The cups were representative of a thin wall and thin base specimen, whereas the draw pieces have a thick base (1/4 in.) and a thick wall (approximately 3/32 in.). Both types of specimens contained high residual stress and cracked in less than one minute in a solution of I per cent mercurous nitrate and I per cent nitric acid provided that this was preceded by a 30-sec. pickle in 40 per cent nitric acid. Specimens were prepared as follows: (I) degreased in trichlorethylene, (2) rinsed in H20, (3) pickled 5 min. in 10 per cent by volume H2SO4 (1.84 sp. gr.), (4) rinsed in H2O, and (5) dried. Amines Tested In selecting the amines, representatives of the three series of amines and one series of substituted amines were chosen. The aliphatic series was represented by the methyl and ethyl primary, secondary and tertiary amines. These are the simplest aliphatic amines. For the aromatic series, the phenyl primary, secondary and tertiary amines were selected as being the simplest. The heterocyclic series was represented by pyridine, which is a simple heterocyclic base (tertiary amine).

Jan 1, 1944

By A. L. Jamieson, H. Rosenthal

The action of mercury on stressed brass to produce cracks was known before Moore, Beckinsale and Mallinson1 showed that actual season cracking did not occur spontaneously but could be induced by ammonia. These investigators studied other substances, including diphenylamine, without finding that anything other than ammonia could cause season cracking Grimston2 reported season cracking in cartridge cases stored in wooden boxes wetted with dilute sulphuric acid pickling solution. Season cracking associated with sulphur dioxide, water vapor and air has been reported by Johnston,3 although he reported that trimethylamine and pyridine did not cause cracking. Jevons4 has ascribed season cracking of brass in certain instances to trimethylamine, "aldehyde amine," "ketone amine" and pyridine, but no experimental work was done evidently to prove this definitely. Pyridine was investigated by Morris,5 who found it to have considerable cracking power. In the present investigation, the object was a qualitative evaluation of a number of representative amines with respect to their ability to cause season cracking. Thus it was desired only that an appreciable vapor pressure of each amine be obtained in order to make the test as severe as possible, without attempting to test equivalent concentrations for comparative purposes. MEthods Specimens TWO types of specimen were used: 1. Unannealed 70-30 brass CUPs formed from 0.040-in. thick sheet. Height of cup Was 13/8 in. and diameter was 17/8 inches. 2. First draw pieces of caliber .50 cartridge cases in the unannealed condition (70-30 brass)- The cups were representative of a thin wall and thin base specimen, whereas the draw pieces have a thick base (1/4 in.) and a thick wall (approximately 3/32 in.). Both types of specimens contained high residual stress and cracked in less than one minute in a solution of I per cent mercurous nitrate and I per cent nitric acid provided that this was receded by a 30-sec. pickle in 40 per cent nitric acid. Specimens were prepared as follows: (1) degreased in trichlorethylene, (2) rinsed in H2O, (3) pickled 5 min. in 10 per cent by volume H2SO4 (1.84 SP. gr.), (4) rinsed in H2O, and (5) dried. Amirtes Tested In selecting the amines, representatives of the three series of amines, and one series of substituted amines were chosen. The aliphatic series was represented by the methyl and ethyl primary, secondary and tertiary amines. These are the simplest aliphatic amines. For the aromatic series, the phenyl primary, secondary and tertiary amines were selected as being the simplest. The heterocyclic series was represented by pyridine, which is a simple heterocyclic base (tertiary amine).

Jan 1, 1944

By Robert S. Shoemaker

Receiving the Richards Award is undoubtedly the most memorable event in my entire life. There should, however, be more names engraved on it. These are the names of men who were my teachers (but not all of the academic variety) and my friends, each of whom had a part in my ever continuing education and thus have a part of this award. There was Bill Caldwell who made me into a chemist, and Will Shorey who added a lot of ore dressing. There was Rush Spedden who put me to work in his minerals research lab, Joe Brennan who made me turn my research into plant practice, and Tom Meek who sent me all over the world on metallurgical jobs. Bob Cheatham and Abe Dor taught me to try to give the client what he needs rather than what he wants, while Ed Malouf and Casey Davis always gave their particular brand of advice at exactly the right time. And, lastly, there was Leo Abell and Frank McQuiston, both fine metallurgists and the best friends a man could have. In addition to those I have mentioned, there are literally scores of others I would like to acknowledge with my sincere appreciation.

Jan 6, 1974