Search Documents

Here, published for the first time, is the group of Anaconda officials (New York office) concerned with the planning and operations of the company's copper properties in Chile.

Jan 1, 1952

By George W. Small

The ore, as it is raised from the mine, has all average assay-value of $11 per ton, chiefly in the form of free gold. All the ore goes directly to the stamp-mills, of which there are two. The older and larger mill contains sixteen batteries of five stamps each, with one Frue vanner to each battery. The new mill has eight batteries of five stamps and two Frues to each battery. The large mill is driven by Leffel turbine wheels, with a pressure of eighty feet, and a consumption of 600 miners' inches of water. The smaller mill is driven by "hurdy-gurdy" wheels with a pressure of about 550 feet and a consumption of 150 inches of water. At both mills the tailings from the stamps pass over about 20 feet of plates on their way to the Frues. In each set of plates the first or upper one is copper, the rest are so-called silver plates. The bullion from the stamps is about 800 fine in gold and 200 in silver. The concentrates from the Frues average from 11/4 to 1 ; per cent. of the ore stamped. They very rarely exceed 2 per cent. I was unable to get the exact assay-value of the concentrates, but it is said to vary between $100 and $200 per ton. The concentrates are treated at the chlorination works at the rate of one hundred tons per month. The capacity of the works is somewhat greater than this, but as the supply of concentrates is limited it is not deemed advisable to work them up any faster. Care is taken to keep the concentrates always damp until they are put into the roasting furnace. If this is not done, a decomposition of the pyrites begins, forming lumps which do not roast, and which consequently cause a loss of gold in the residues from leaching. A Fortschaufelungsofen is used for roasting. Its dimensions, incloding fire-box, are 12' X 80'. The hearth is one continuous plane, but the charges, of which there are three in the furnace at one time, are kept entirely separate. The furnace-men call the three compartments, the "drying," the " burning," and the " cooking" compartments. In the middle, or "burning" compartment, the ore is spread

Jan 1, 1887

By Wilbur Nelson

ALL of our accounts of the discovery of copper ore at Ducktown, Tenn., state that the discovery was made in August, 1843, yet it would appear that samples of copper from this district were found by the Spanish explorer, DeSoto, when he wandered into Southern Tennessee, in 1539, in his four years of exploration through the Southern States. The following quotation is taken from his diary: "Towards the north there was a province named Chisca; and that there was a melting of copper, and of another metall of the same colour, save that it was finer, and of a farre more perfect colour, and farre better to the sight, and that they used it not so much, because it was softer. And the selfe same thing was told the governor in Cutifa-Chiqui, where we saw some little hatchets of copper, which were said to have a mixture of gold. But in that part of the country it was not well peopled; and they said there were mountains, which the horses could not passe; and for that cause, the governor would not goe from Cutifa-Chiqui directly quicker." DeSoto sent two of his company to try to find these mines, but after five days' wandering through the mountains they returned, stating that their guides had become lost. Although the Ducktown area may have been known to the ancient Indians, it was not until August, 1843, when a Mr. Lemmons, who was panning for gold on Potato Creek, in the Ducktown basin, found some reddish-brown decomposed rock, which he supposed to be gold, that the copper deposits were actually discovered. His disgust on finding that this yellow metal. was not gold was so great that he did not. try to develop his find. In March, 1847, B. C. Dugger erected an iron forge at this same place, but was unable to work the iron as it contained so much copper that on cooling it would break to pieces. The finding of copper in the iron ore by Mr. Dugger led to further explorations; and in April, of the same year, A. J. Weaver, who was passing through that country, told the people that the black rocks they had dug out were rich copper ore. Mr. Weaver began the first mining in this district.

Jan 10, 1924

By E. P. Hindes

The total amount of oil produced in the state of Oklahoma during the year 1928 was 242,286,400 bbl., as compared to 273,372,650 bbl. in 1927; 177,650,000 bbl. in 1926; and 167,900,000 bbl. in 1925. The year 1928 ranks second to 1927 in which more oil was produced in the state than in any previous year. The large in in 1927 and 1928 was due principally to the development of the Greater Seminole district. The decrease of approximately 31,000,000 bbl. in the 1928 production as compared with the production in 1927, was caused by a drop of nearly 8,500,000 bbl. in the Seminole district production and a more or less normal decline in the production of practically all the other older and more settled fields. During 1928 approximately 1800 producing wells were drilled in Oklahoma, which yielded during the year approximately 90,000,000 bbl. of oil. The average initial production of these wells was 850 bbl. per day, and the average daily production per well for the year was 137 bbl. The average daily production per well of the total number of wells producing in 1928 was 10.9 bbl., which is a 13.5 per cent. decrease from the 1927 average of 12.6 barrels. At the close of 1928 a total of 95,400 producing wells had been drilled in the state, and approximately 61,000 were still producing. The grand total amount of oil produced in the state from the time the first well was drilled up to and including 1928 was 2,553,000,000 bbl. The production in 1928 was 9.5 per cent. of the total oil produced in the state. Texas led all other states in 1928, with a production of 251,835,200 bbl. Oklahoma was second with 242,286,400 bbl., and California was third with 231,982,600 barrels. Fields outside Greater. Seminole District Practically all the old settled fields in Oklahoma experienced a normal and expected decline during the year 1928. The fields showing the most, pronounced decline as compared to 1927 were: Burbank, which dropped from 15,230,400 to 11,939, 150 bbl.; Tonkawa, from 7,692,000 to 4,952,900 bbl.; Garber, from 5,056,300 to 3,139,400 bbl., and Wewoka, from 6,188,-800 to 2,450,400 bbl. There were no new extensions, discoveries of

Jan 1, 1929

H. M. BOYLSTON, Cambridge, Mass.-I would first like to ask what machine Capt. Bellis used to make his tests on impact strength. I have made some tests with the Charpy impact machine, the specimen being supported at both ends and nicked in the middle, and, find that the results do not always agree with those obtained by the Izod and other machines. I would also like to ask what effect the composition and heat treatment of the tool steel had on the drilling of his rifle barrels, as compared, with the heat treatment of the steel itself? I notice that the analysis of the composition of steel used shows sulphur 0.050 and phosphorus 0.065; I should like to ask how those high limits of sulphur and phosphorus came to be allowed? I have some data which lead me to feel pretty certain that those high limits make for very unsafe steel in rifle barrels. It has never been explained to the satisfaction of all of us, why the manganese is so high: 1.22 per cent. I believe several reasons have been stated; among them, that it is high in order to compensate for the high sulphur, and also to increase the elastic limit and improve other physical properties of steel. Lastly, I wish to ask whether Capt. Bellis has tried any different methods of heat-treating his steel rifle barrels? Apparently these were all heat-treated before machining; has he had any experience with heat-treatment after machining, especially after drilling? Those questions may seem somewhat outside of the range of this -paper, but they are important, and if Captain Bellis can give us any information, it will be very helpful. Dr. J. A. MATHEWS,* Syracuse, N. Y.-The same subject was discussed here last year, and the earlier papers by Dr. Carle Hayward seem to indicate that nothing was gained by the length of time of 'tempering. (It should be borne in mind that his results were based upon electrical and magnetic measurements and not upon tensile tests.) That idea has been accepted as gospel by steel workers, until late years, and particu-larly in connection with alloy steels, on which there is no question that the effect of time of tempering is very marked.

Jan 4, 1918

By H. C. George

Since 1911, when J. L. Dunn first used compressed air for repressuring depleted oil sands in southeast Ohio, the rejuvenation of many depleted oil fields has been directly due to repressuring by means of air or gas. Developments in repressuring in recent years have resulted in its successful use in the early life of some deep, high-pressure oil fields, conserving the natural gas dissolved in and associated with the oil by returning it to the producing oil sand after it has been compressed above the existing rock pressure of the reservoir. One of the most successful operations of this type is that of the Humble Oil & Refining Co., on the DeWalt salt dome at Sugarland, Texas. I quote from a personal communication with reference to this field: "Structurally, the field is dome-shaped, having a closure of approximately 350 ft. Production comes from a sandy shale interbedded with a clean sand and lying over a cap rock which is about 3400 ft. deep on top of the structure." A feature of the operation of this field is the production of the required amount of oil with the minimum of gas production. Wells on top of the dome have high gas-oil ratios, while those down structure have lower ratios, depending upon the distance of the well from the peak. To date, it has been possible to produce the oil needed from the wells circling the dome above the water zone and below the gas zone, and in this manner the average gas-oil ratio has been kept low. The gas from all separators is turned into a gas system which serves the entire field. From this system, all drilling rigs and utilities requiring gas for a fuel draw their requirements, and the remainder of the gas (about two-thirds of the production) is delivered to a compressor plant which boosts the pressure until it can be returned to the sand at the top of the dome where the rock pressure is 1400 lb, per square inch. "The Sugarland wells produce through 2-in. tubing with a 3/8-in. choke in one wing of the well-head manifold. The pressure builds up as high as 1300 lb, per square inch on the casing while on the tubing it varies from 0 to 900 lb. per square inch, depending upon the amount of gas produced with the oil."

Jan 1, 1931

By Olin G. Bell

At the beginning of the year 1935 the older fields in Southwest Texas, and particularly those discovered during 1934, had been practically delimited and only normal development continued. As a result, operations in this area were somewhat slowed down. Shortly after the first of the year, however, activity in the area was greatly accelerated, due largely to the fact that the Loma Novio field, discovered during the last few days of 1934, indicated the presence of a new productive trend east of and parallel to the Government Wells field and also indicated the presence of a new productive horizon, the Loma Novio sand, approximately 100 ft. lower than the Government Wells sand zone. Other discoveries during the year greatly augmented the activity in the district. During the year there were 651 oil wells, 53 gas wells and 275 dry holes drilled in this area during the year. Most of the operations were in the Government Wells, Cole, Loma Novio, Seven Sisters and Lopez fields. New Fields Four new fields were discovered during 1935 as follows: Seven Sisters and Piedra de Lumbre in Duval County; Loma Alto in McMullen County; and Lopez in Webb County. Seven Sisters Field.—The Seven Sisters field, opened in May, was the direct result of a systematic search for new productive areas northeast of the Loma Novio field. The first producer, Harvey & Henderson NO. 1 Chernosky, survey 226, was completed in the Labbe (Chernosky) sand at 2220 ft. However, the second producer, Santa Clara Oil Co. No. 1 Welder in survey 385, drilled about one mile south of the discovery well, failed to find production in the Labbé sand and was carried on down and completed in the Government Wells sand at 2473 ft. with an initial production of 20 bbl. of oil per hour. These two discoveries, in the Labbé and Government Wells sand, started an active leasing and drilling campaign in this part of Duval County and drilling operations continued especially active throughout the remainder of the year.

Jan 1, 1936

By Olin G. Bell

At the beginning of the year 1935 the older fields in Southwest Texas, and particularly those discovered during 1934, had been practically delimited and only normal development continued. As a result, operations in this area were somewhat slowed down. Shortly after the first of the year, however, activity in the area was greatly accelerated, due largely to the fact that the Loma Novio field, discovered during the last few days of 1934, indicated the presence of a new productive trend east of and parallel to the Government Wells field and also indicated the presence of a new productive horizon, the Loma Novio sand, approximately 100 ft. lower than the Government Wells sand zone. Other discoveries during the year greatly augmented the activity in the district. During the year there were 651 oil wells, 53 gas wells and 275 dry holes drilled in this area during the year. Most of the operations were in the Government Wells, Cole, Loma Novio, Seven Sisters and Lopez fields. New Fields Four new fields were discovered during 1935 as follows: Seven Sisters and Piedra de Lumbre in Duval County; Loma Alto in McMullen County; and Lopez in Webb County. Seven Sisters Field.—The Seven Sisters field, opened in May, was the direct result of a systematic search for new productive areas northeast of the Loma Novio field. The first producer, Harvey & Henderson NO. 1 Chernosky, survey 226, was completed in the Labbe (Chernosky) sand at 2220 ft. However, the second producer, Santa Clara Oil Co. No. 1 Welder in survey 385, drilled about one mile south of the discovery well, failed to find production in the Labbé sand and was carried on down and completed in the Government Wells sand at 2473 ft. with an initial production of 20 bbl. of oil per hour. These two discoveries, in the Labbé and Government Wells sand, started an active leasing and drilling campaign in this part of Duval County and drilling operations continued especially active throughout the remainder of the year.

Jan 1, 1936

By G. C. Broadhead

THE lead district of Southeast Missouri covers an area of over 3000 square miles, including Maries County on the west, Jefferson on the east, Franklin on the north, and part of Madison on the south, or parts of ten counties. A general section of the rocks of the southeast part of this region would be about as follows, numbering from the top 1. Sandstone (the second of Missouri geologists), - 20 feet. 2. Cbert beds-beds of passage below, - 125 feet 3. Magnesian limestone, chert, and quartzite, - 100 to 300 feet 4. Lower magnesian limestone, - 100 to 150 feet 5. Gritstone and lingula beds, - 50 feet 6. Ozark marble beds, - 5 to 20 feet 7. Sandstone and conglomerate, - 5 to 90 feet 8. Porphyry, Archaean. 9. Granite, The thickness is approximate, for it is not possible to obtain the correct thickness of the various beds. No. 1 may be seen as de¬tached outliers or loose masses of a hard sandstone or quartzite, and is found on the hilltops in the southern part of Madison County, in like topographical position in Reynolds County and the western part of Washington County. No. 2 consists of alternations of chert, clay, and quartzite. It is the formation which contains most of the limonite deposits of Central and Southern Missouri. In Reynolds County shafts have pene¬trated it 75 feet. Outcrops there and in Madison would indicate it to be at least 125 feet thick. Fossils obtained in various places prove it clearly to be of the age of the calciferous sandrock of the New York system, and Nos. 1 and 2 may also be referred to the age of the second sandstone of Missouri. No. 3 consists chiefly of thick beds of ash, drab and flesh-colored magnesian limestone, both coarse and fine-grained. These beds, where they occur, in Washington, Jefferson, and the southern part of Madison Counties, contain a good deal of quartz in drusy cavities. In Washington County the limestones are beautifully ramified by a system of connected drusy cavities generally lined with minute quartz crystals arranged in botryoidal and mammillary forms, and called u mineral blossom " by the miners. This is the lead-bearing rock of Washington County, but in the southern part of Madison it does not appear to be galeniferous. It is also undoubtedly the equivalent of

Jan 1, 1877

By G. C. Broadhead

The lead district of Southeast Missouri covers an area of over 3000 square miles, including Maries County on the west, Jefferson on the east, Franklin on the north, and part of Madison on the south, or parts of ten counties. A general section of the rocks of the southeast part of this region would be about as follows, numbering from the top: 1. Sandstone (the second of Missouri geologists),.... 20 feet. 2. Chert beds—beds of passage below,...... 126 " 3. Magnesian limestone, chert, and quartzite,. .. 100 to 300 " 4. Lower magnesian limestone,......100 to 150 " 5. Gritstone and lingula beds,....... 50 " 6. Ozark marble beds,........5 to 20 " 7. Sandstone and conglomerate,. .. .. 5 to 90 " 8. Porphyry, Archæan 9. Granite, The thickness is approximate, for it is not possible to obtain the correct thickness of the various beds. No. 1 may be seen as detached outliers or loose masses of a hard sandstone or quartzite, and is found on the hilltops in the southern part of Madison County, in like topographical position in Reynolds County and the western part of Washington County. No. 2 consists of alternations of chert, clay, and quartzite. It is the formation which contains most of the limonite deposits of Central and Southern Missouri. In Reynolds County shafts have penetrated it 75 feet. Outcrops there and in Madison would indicate it to be at least 125 feet thick. Fossils obtained in various places prove it clearly to be of the age of the calciferous saudrock of the New York system, and Nos. 1 and 2 may also be referred to the age of the second sandstone of Missouri. No. 3 consists chiefly of thick beds of ash, drab and flesh-colored magnesian limestone, both coarse and fine-grained. These beds, where they occur, in Washington, Jefferson, and the southern part of Madison Counties, contain a good deal of quartz in drusy cavities. In Washington County the limestones are beautifully ramified by a system of connected drusy cavities generally lined with minute quartz crystals arranged in botryoidal and mammillary forms, and called " mineral blossom " by the miners. This is the lead-bearing rock of Washington County, but in the southern part of Madison it does not appear to be galeniferous. It is also undoubtedly the equivalent of

[YEAR OF ELECTION 1913. FRANK DAWSON ADAMS Montreal, Canada 1938. HENRY CORT HAROLD CARPENTER London, England 1933. KARL EILERS New York, N. Y. 1922. FEDERICO GIOLITTI Torino, Italy 1906. SIR ROBERT A. HADFIELD London, England 1921. FRANK WILLIAM HARBORD London, England 1917. HERBERT HOOVER York, N. Y. 1939. HENRY KRUMB New York, N.' Y. 1921. C. McDERMID London, England 1913. EZEQUIEL ORDONEZ Mexico City, Mexico 1935. ROBERT PEELE New York, N. Y. 1938. A. M. PORTEVIN Paris, France 1937. JOHN V. W. REYNDERS New York, N. Y. 1937. GEORGE S. RICE Washington, D. C. 1911. ROBERT H. RICHARDS Cambridge, Mass. 1934. T. A. RICKARD Victoria, B.C., Canada]

Jan 1, 1940

[ ]

Jan 1, 1938

By G. F. Tagg

In an earlier paper1, the author described a method of interpreting earth-resistivity curves, based on the theoretical investigation of a single horizontal underlying stratum. If the four-electrode system of Wenner is employed, the resistivity in a homogeneous soil is given by the formula where a is the electrode separation and R is the resistance of the earth between the two inner electrodes. If the earth is not perfectly homogeneous, the application of this formula gives an apparent specific resistance varying with the electrode separation. In the special case of the single horizontal underlying stratum, there is a surface layer of thickness h and resistivity p1 and a lower layer, extending to infinity, of resistivity pz. It has been shown by Lancaster-Jones2 that the apparent resistivity obtained by an application of equation 1 is related to the true resistivities, the depth h and the electrode separation a by an expression of the formhere pa is the apparent resistivity and F is a function (actually an infinite series), of the ratio h/a, and a reflection coefficient k = (p2 — p1)/(p2 + p1). For given values of h/a and k, the right-hand side of equation 2 can be calculated, and curves drawn showing the relationship between pa/p1, h/a and k. Such a set of curves for the case when p1 > p2 is given in Fig. 1. When pl is less than pz it is more convenient to use conductivity instead of resistivity. Hence, if oa = the apparent conductivity = lip, and a1 = the conductivity of the upper layer = l/pl, it follows that GeophyGical prospecting by earth-resistivity methods is frequently applied to investigation of structural problems in geology. Fig. 1 indicates a scheme of the general arrangement used in these methods of measurements. The battery (or generator) E is connected with two "current electrodes" I1 and I2. The current of intensity J, supplied by this battery, passes through the earth between these elcc- trodes. A potential difference U will be measured between two other electrodes V1 and Vz, called "potential electrodes." According to the configuration of electrodes (Fig. I), the resistivity of a homogeneous soil results from the formula

Jan 1, 1940

By G. F. Tagg

In an earlier paper1, the author described a method of interpreting earth-resistivity curves, based on the theoretical investigation of a single horizontal underlying stratum. If the four-electrode system of Wenner is employed, the resistivity in a homogeneous soil is given by the formula where a is the electrode separation and R is the resistance of the earth between the two inner electrodes. If the earth is not perfectly homogeneous, the application of this formula gives an apparent specific resistance varying with the electrode separation. In the special case of the single horizontal underlying stratum, there is a surface layer of thickness h and resistivity p1 and a lower layer, extending to infinity, of resistivity pz. It has been shown by Lancaster-Jones2 that the apparent resistivity obtained by an application of equation 1 is related to the true resistivities, the depth h and the electrode separation a by an expression of the formhere pa is the apparent resistivity and F is a function (actually an infinite series), of the ratio h/a, and a reflection coefficient k = (p2 — p1)/(p2 + p1). For given values of h/a and k, the right-hand side of equation 2 can be calculated, and curves drawn showing the relationship between pa/p1, h/a and k. Such a set of curves for the case when p1 > p2 is given in Fig. 1. When pl is less than pz it is more convenient to use conductivity instead of resistivity. Hence, if oa = the apparent conductivity = lip, and a1 = the conductivity of the upper layer = l/pl, it follows that GeophyGical prospecting by earth-resistivity methods is frequently applied to investigation of structural problems in geology. Fig. 1 indicates a scheme of the general arrangement used in these methods of measurements. The battery (or generator) E is connected with two "current electrodes" I1 and I2. The current of intensity J, supplied by this battery, passes through the earth between these elcc- trodes. A potential difference U will be measured between two other electrodes V1 and Vz, called "potential electrodes." According to the configuration of electrodes (Fig. I), the resistivity of a homogeneous soil results from the formula

Jan 1, 1940

By H. C. Chang, N. J. Grant, A. R. Chaudhuri

During the creep of coarse-grained polycrystalline magnesium at elevated temperatures, a nonbasal type of slip was found to play an important role in the deformation processes. The nonbasal slip traces were examined metallographically in eight specimens (13 grains) and the observed glide plane located stereographically for each grain. The tests were run at 500&apos; and 700°F at stresses of 148 to 786 psi. Based on these measurements and theoretical calculations, the crystallographic elements for nonbasal slip were determined. WHEN a metal deforms by slip, the conventional appearance of the slip bands on the surface of a specimen is that of straight lines. Such is the behavior of the face-centered-cubic metals, as for example, aluminum. The particular slip system on which slip occurs in these metals is governed by the criterion of resolved shear stress. Work on the body-centered-cubic metals a-iron,&apos;. &apos; molybdenum, and columbium4 has shown that the process of slip is somewhat more complicated than the simple gliding of one close-packed plane of atoms over another in a close-packed direction and that it results in the formation of wavy and irregular slip traces on the surface. The recent reviews and experiments of Vogel and Brick and Chen and Mad-din3 show that, for the body-centered-cubic metals, the resolved shear stresses along the planes and the degree of close-packing do not necessarily determine the slip system. Theirs and other investigations indicate that a complete understanding of the slip process in the body-centered-cubic metals is not yet possible. However, one behavior displayed by all these metals is that the slip direction is invariably one of the close-packed directions <11l>. The wavy nature of the slip-band traces has been explained on the basis of cooperative slip by planes sharing this same slip direction.1&apos;3l&apos; It is generally acknowledged that, when the hexagonal-close-packed metal magnesium (axial ratio c/a = 1.624) deforms by slip at room temperature, it does so by basal slip in the close-packed direction <1I%>. This type of slip has the conventional appearance of straight lines and is governed by the critical shear-stress law. Schmid and coworkers" showed that basal slip was operative in the temperature range of —185" to 300°C (—300" to 572°F). Work by Servi, Norton, and Grant6 has shown that, during the creep of coarse-grained aluminum at high temperatures, new slip systems come into operation. The existence of a new high temperature slip system at temperatures greater than 225 °C (437°F) for magnesium was suggested also by Schmid. This was later indicated by Bakarian and Mathewson&apos; to be slip along the pyramidal planes (10i1) in the close-packed direction <11%>.* They * Mention will be made in the text of pyramidal planes and prismatic planes. The pyramidal planes referred to are the type I. order 1 of the form {10il); and the prismatic planes of the type 1 of the form (10i0). For the sake of brevity, they are termed in the teat as pyramidal (10il: and prismatic (10i0) planes, respectively. Where reference is made to the pyramidal plane type 1, order 2 of the form {10i2), they are referred to as the pyramidal planes of the type (10i2:. observed that this kind of slip resulted in irregular markings on the specimen surface. According to them, a possible cause for the appearance of the markings was due to "limited accessory slip on the pyramidal {10i2) planes." Burke and Hibbard," on deforming a single crystal of magnesium at room temperature, found evidence of slip on a pyramidal plane {1011). They explained it as being due to the effect of grip restraints. It is pertinent to note at this point that, although basal slip has received a fair amount of attention, only two specimens have been investigated, that of Bakarian and Mathewson and of Burke and Hibbard, to establish the elements of nonbasal slip in magnesium. During the study of the deformation mechanisms

Jan 1, 1956

By D. Mills, G. B. Craig

ZIRCONIUM has been float-zone-refined in an electron-beam furnace and the redistribution of oxygen, iron, and tungsten has been measured. The iodide zirconium used in the present experiments initially contained both oxygen and iron in the range 100 to 200 ppm by weight, and tungsten in amounts less than 10 ppm. Float-zone refining of zirconium, using induction heating, has previously been attempted by Kneip and Betterton1 and Langeron.2 Kneip and Betterton were primarily interested in the removal of iron and nickel. They achieved some purification, with respect to both these elements, in material given up to six passes at 150 mm per hr under an argon atmosphere. Langeron reported purification for a large number of elements after four completed passes in a static vacuum system operating at pressures less than 10-6 mm of Hg and with rates of zone travel between 30 and 40 mm per hr. He did not report oxygen concentrations, but stated that there was inverse segregation of this element. westlake5 has also used a minimum of four zone passes to remove iron from zirconium. No rates or conditions were given. Belk6 has shown that tungsten contamination can occur during electron-beam melting. He reported an increase from 0.01 to 0.05 pct by weight tungsten in molybdenum after four complete zone passes. The vacuum system for the electron-beam unit used in the present investigation consisted of a single-stage rotary pump backing a liquid-air-trapped oil-diffusion pump. A pressure of less than 10-8 mm of Hg was obtained with Dow-Corning 705 fluid in the diffusion pump. In order to avoid contamination of the zirconium by evaporation from the tungsten filament, a special focusing cage4 was employed. Three rates of zone travel, 114, 38, and 4 mm per hr, were investigated, with the liquid zone moving from the bottom to the top of the bar. The bars used were 3 mm diam and the total melted length was 130 mm. Oxygen was analyzed by neutron-activation analysis using a neutron flux of 10&apos; neutrons per sq cm per sec to form the isotope N16 by the 016 (n,p) N16 reaction. The standard deviation is quoted for each oxygen determination. The iron and tungsten analyses were performed spectrographically, and the precision is estimated to be ±6 pct. Analyses for tungsten were all below the detectable limit of 10 ppm, confirming the protection given by the focusing cage. No significant redistribution of oxygen was found at the two higher rates of zone travel. The redistribution of oxygen and iron obtained after five passes at a rate of zone travel of 4 mm per hr (1.1 x 10-4 cm per sec) is recorded in Tables I and 11. Burris, Stockman, and Dillon3 have estimated the distribution of solutes during multipass zone refining. Using their curves for an effective distribution coefficient of Keff = 1.5 and 2 for oxygen and Keff = 0.3 for iron, the expected concentrations were estimated for the present material. These are shown in Tables I and 11, along with the experimentally measured values. The calculated concentrations are based on a molten-zone length of 10 pct of the total melted length, whereas in the present experiments the molten zone was approximately 5 pct of the total melted length. The effect of zone length on solute redistribution is most pronounced after a large number of zone passes. Comparison with Pfann&apos;s published data8 for solute redistribution for various Keff&apos;s and zone lengths indicates only small differences at low numbers of completed zone passes. It is evident that the expected distribution has not been realized in the case of iron. Scrapings of material deposited on the inner surfaces of the electron-focusing cage were found to be magnetic. It is, therefore, concluded that redistribution of iron is masked by evaporation. Deposition of iron inside the focusing cage was observed at all rates of zone travel. The results of the investigation may be summarized as follows: 1) Segregation of oxygen is typical for a solute with a distribution coefficient, Keff > 1. 2) No redistribution of oxygen takes place at high rates of zone travel. 3) The distribution coefficient for oxygen lies between 1.5 and 2.0. 4) Purification with respect to iron occurs mainly by evaporation. 5) The focusing cage is effective in preventing tungsten contamination.

Jan 1, 1967

By W. H. Geis

The following pages summarize the causes that led to the suggestion of unit operation of the paloma field, the organization of com-mittees, preparation of the Paloma Operators Agreement and the reasons for rejection of the plan. Introduction Long ago an Austrian physicist observed that under certain conditions the condensation of a liquid from gaseous mixtures resulted from pressure reduction. Some 50 years later he would have known that his research was not in vain. He would have seen a group of serious operators and engineers seeking to apply that principle to a conservation . program for unitized production in the Paloma gas field—but he would also have been saddened to see that forces unsympathetic to the application of science in oil production, with little or no appreciation of modern methods and the advantages of cooperation, so far have prevented the adoption of that program. Soon after the Paloma field was discovered it was realized that all the hydrocarbons in the reservoir existed in the gaseous phase. This condition was confirmed over a large area. Therefore, if the field was to be properly exploited with the greatest ultimate recovery of condensate, the hydrocarbons in the reservoir must be produced in the single or gas phase. They must be cautiously extracted with the least possible reduction of the natural pressure. If this could be accomplished, or if artificial pressure control were utilized, the condensation and underground loss of the valuable distillate would be preventable—otherwise it would not be. Wholehearted cooperation of all oper-ators was required in order to accomplish the conservation purposes of the program. To this end the production engineers of the several companies concerned lent their time and talents. They fully investigated the physical relationships of the products within the complicated gaseous mixture, prepared extensive reports on the subject and drew up a reasonably efficient plan of operations, which now is commonly called the "Paloma Unit Plan" but actually was entitled "The Paloma Operators Agreement." All of the engineers were not in perfect agreement on all the features of the plan, or even on all the engineering principles. However, it is safe to say that on all the important or essential factors there was a unanimity of opinion, particularly as to the objectives. These were fairly simple and reduce to one controlling item, "pressure control" by cycling or recycling. Organization The principal operators initiated the program by calling a meeting of all the lessees in the area, at which an organization was perfected, known as the "Paloma Operators Committee." Various subcommittees were appointed to expedite the work, including an "Engineering Committee." These func-tioned in a businesslike manner, frequently reported to the superior committee and

Jan 1, 1942

By W. H. Geis

The following pages summarize the causes that led to the suggestion of unit operation of the paloma field, the organization of com-mittees, preparation of the Paloma Operators Agreement and the reasons for rejection of the plan. Introduction Long ago an Austrian physicist observed that under certain conditions the condensation of a liquid from gaseous mixtures resulted from pressure reduction. Some 50 years later he would have known that his research was not in vain. He would have seen a group of serious operators and engineers seeking to apply that principle to a conservation . program for unitized production in the Paloma gas field—but he would also have been saddened to see that forces unsympathetic to the application of science in oil production, with little or no appreciation of modern methods and the advantages of cooperation, so far have prevented the adoption of that program. Soon after the Paloma field was discovered it was realized that all the hydrocarbons in the reservoir existed in the gaseous phase. This condition was confirmed over a large area. Therefore, if the field was to be properly exploited with the greatest ultimate recovery of condensate, the hydrocarbons in the reservoir must be produced in the single or gas phase. They must be cautiously extracted with the least possible reduction of the natural pressure. If this could be accomplished, or if artificial pressure control were utilized, the condensation and underground loss of the valuable distillate would be preventable—otherwise it would not be. Wholehearted cooperation of all oper-ators was required in order to accomplish the conservation purposes of the program. To this end the production engineers of the several companies concerned lent their time and talents. They fully investigated the physical relationships of the products within the complicated gaseous mixture, prepared extensive reports on the subject and drew up a reasonably efficient plan of operations, which now is commonly called the "Paloma Unit Plan" but actually was entitled "The Paloma Operators Agreement." All of the engineers were not in perfect agreement on all the features of the plan, or even on all the engineering principles. However, it is safe to say that on all the important or essential factors there was a unanimity of opinion, particularly as to the objectives. These were fairly simple and reduce to one controlling item, "pressure control" by cycling or recycling. Organization The principal operators initiated the program by calling a meeting of all the lessees in the area, at which an organization was perfected, known as the "Paloma Operators Committee." Various subcommittees were appointed to expedite the work, including an "Engineering Committee." These func-tioned in a businesslike manner, frequently reported to the superior committee and

Jan 1, 1942

By Ralph H. Sweetser

AT the joint session of Blast Furnace and Open Hearth Committees, April 7, 1937, at Birmingham, the subject of the quality of basic open-hearth pig iron was so well presented and discussed from so many different viewpoints that it was the general opinion that progress had been made and that such meetings were conducive to the advancement of the art of making pig iron of the right quality for the open-hearth man to produce the most satisfactory quality of steel. It was agreed that there is a decided differentiation between the chemical analysis of pig iron and the "quality" of pig iron. Paul J. McKim said that open-hearth furnace operators frequently make reference to certain types of iron as "bad iron," "dirty iron," "cold metal," etc., claiming that when using these irons, although they are within specified chemical analysis, it is impossible to produce quality steel. Mr. McKim gave a list of the suggested causes of those "certain types" of bad irons that have a thoroughly respectable analysis but a thoroughly disreputable character. Another open-hearth man, P. A. MacIsaac, of Nova Scotia, said that The effects of iron that is below standard in analysis or in that mysterious property called quality, are well known to all open-hearth operators. It has been shown that iron of this type results in the production of steels on which the rejections of finished product run high. What is to be done about it? I would say that the burden of producing high-quality iron should be placed squarely on the shoulders of the blast furnace man, even as that of making good steel is shouldered by the open-hearth man. It is the purpose of this paper to bring out into the open this "mysterious property called quality"; that is, in those "certain types" of basic pig iron that make it impossible to produce quality steels; and at the same time to point the way for the blast-furnace man to be able to shoulder the burden that Mr. MacIsaac and all other open-hearth men and foundry-men have placed upon him. Silicon, sulphur, phosphorus and manganese are not the guilty elements because these are known, specified and usually kept within the

Jan 1, 1938

By Richard Pearce

WHILST most of the silver- and copper-bearing veins of Butte have characters somewhat similar, the Gagnon vein has certain rather remarkable features which are not noticed in any of the other mines. The silver-veins proper, as illustrated in the Alice, Lexington, Moulton, and many others, have certain well-known typical characters. Manganese is always present in variable quantities as rhodocrosite or rhodonite, associated with quartz, pyrite, and sphalerite, and with little or no copper. The copper-veins also have certain mineralogical characteristics, which are very similar, or different only in minor points. Chalcocite, chalcopyrite, bornite, enargite, with variable quantities of pyrite, may be said to represent the general mineralogical features of these lodes. It is worth noticing that while the silver-bearing lodes have more or less sphalerite, this mineral is almost entirely

Jan 1, 1888