Search Documents

By L. J. Buck

Lead smelting in the ore hearth, first practiced in Europe, whence the traditional name "Scotch hearth, and later developed in America to its present efficiency, is based upon the roast reduction process and is applicable to relatively high-grade galena concentrates. The roast reduction process embraces not only the roast reactions: 2PbS + 70 = PbO + PbSO4, + SO2 PbS + 2PbO = 3Pb + SO2 PbS + 2PbSO4 = Pb + 2PbO + 3SO2 but also, by reason of the addition of extraneous fuel, the reduction reaction: 2PbO + C = 2Pb + CO2 Thus in the ore hearth the roasting of lead sulphide, forming lead oxide and lead sulphate, the reaction of lead oxide and lead sulphate with lead sulphide producing lead, and the reduction of lead oxide by carbon producing lead, go on simultaneously. The Ore Hearth Function of the Ore Hearth.—The ore hearth, through the roast reduction process, provides for the extraction of lead and the immediate disposal of the smelting products—fume, hearth slag and lead, all of which are subsequently treated as follows: the fume is recovered in the flue system and baghouses, mixed with concentrates, and returned to the ore hearth in the form of ore mix; the hearth slag is smelted in a blast furnacc for the further recovery of lead; and the lead is refined and cast into a marketable product. Concentrates Amenable to Ore-hearth Smelting.—Only concentrates that are high in lead content, 70 per cent or more, are ordinarily considered amenable to ore-hearth smelting. Silica should not exceed 2 per cent and iron is allowable only to 4 per cent. These slag-forming constituents occlude both sulphide and mctallic lead, prevent the elimination of sulphur and decrease the lead extraction. Lime and magnesia are beneficial in that both favor a dry slag, promote elimination of sulphur, and prevent occlusions of metallic lead.

Jan 1, 1937

By O. M. TUPPER

REQUIRING a finer ground clay than that obtainable with a dry pan or hammer mill, the Clay Corporation of California installed a five-roller, low- side Raymond impact mill at its Lincoln plant in 1925 and since then has been economically grinding fire clay with a moisture content as high as 15 per cent. This was one of the first, if not the first, of this type of mill to be used in the grinding of clay on the Pacific coast. The pulverizer consists of a die-ring, lying in a horizontal plane, enclosed in a sheet-iron housing. A vertical shaft supports a spider from which five rolls are suspended in such a way as to always have them bearing on the die-ring. The vertical mill shaft is driven by means of beveled gear and pinion from a horizontal shaft which is connected by belt with a 60-hp. motor with suitable pulleys to give a speed of 175 r.p.m. A large fan which has a speed of 1100 r.p.m. and is belt connected to a 40-hp. motor is connected to the mill housing. The discharge end of the fan is in turn connected to a cyclone dust collector.

Jan 1, 1929

The Library of the above-named Societies is open from 9 A.M. to 10 P.M., except on holidays. It contains about 70,000 volumes and 90,000 pamphlets, including sets of technical periodicals and the publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library, through its Library Service Bureau, can render valuable service through correspondence; letters requesting information will receive especial attention. The Library is prepared to furnish references and photographic copies of articles on mining and metallurgical subjects; to determine the existence of mining maps, and to furnish general information on the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may be what is, desired and not include collateral natter which may not be of interest. The time spent in-searching for such collateral matter will be saved, and the information will be sent more, promptly and-in more usable shape.

Jan 2, 1917

By P. J. Potter

Practically all tin-base babbitt metals used in engine bearings are made to customers' specifications, which are many and varied. The copper ranges from 3 to 8 per cent. and the antimony from 4 to 13 per cent.; generally, the babbitt with lower copper content will contain from 4 to 8 per cent. antimony and that with higher copper will have from 7 to 13 per cent. antimony. The allowable lead content varies from 0.20 to 2.00 per cent. If a solder is used as a bonding material instead of tin, the resulting material in the finished bearing will have a higher lead content, but it would not be enough to bring the lead above specifica-tional limits. Impurities such as iron, arsenic and bismuth should be determined in the tin before using to insure a uniform and high-grade product. These points must be considered when segregating and grading the waste that comes from the finishing operations on lined bearings. Classification of SCRAP Because of the extremely rigid nature of most of the specifications for bearing linings it is necessary to use the purest of materials as a base for all compositions. The problem of handling secondary metals is confined almost entirely to the recovery of drosses, spills and turnings incident to the manufacturing operations. As a matter of convenience the waste or scrap may be divided into 10 grades, as follows: 1. Tin from pots where tinning operation is carried out. 2. Tin and babbitt spatters from babbitting operation. - 3. Tin skimmings combined with burned zinc chloride. 4. Borings and reamings. 5. Gates from die-cast bushings and bearings. 6. Drosses from die-cast pots, babbitt foundry pots, and pots in babbittiug room. 7. Babbitt with small amount of bronze from machining operations. 8. Babbitt and bronze borings. 9. Scrap bronze-back babbitt-lined bearings. I 10. Scrap die-cast bearings and bushings. A few of these grades of salvaged material have compositions that make it possible to determine beforehand where they may be used to

Jan 1, 1930

By Byron W. Cheever

In my paper on the estimation of manganese, etc., presented at the Halifax meeting, in September, 1885 (Transactions, xiv., 372), I said that the colorimetric process "can never be made to give reliable results." This statement was based on the results of many trials made by my assistant, Mr. E. D. Campbell, and myself, following in our work the printed and oral directions of others, and such modifications as suggested themselves from time to time. The accuracy of the statement having been questioned, I have, since then, endeavored to find some method of conducting the operation which would give accurate results; I have also tried the methods used by five different chemists; and I am not able to bring the process within the limits of an exact method. While it can fairly be ranked with the colorimetric carbon-process, and can be used for checking the operations of a steel plant, yet it requires more care to obtain uniform results, and is liable to greater variations from slight causes than the carbon-process, and, in my judgment, is not a safe method to employ when exact results are sought.

Jan 1, 1887

By Louis Moyd

The Concrete Research Division, U.S. Corps of Engineers, has developed a simple procedure for determining the coefficients of linear thermal expansion of rocks by means of resistance wire (SR-4) strain gauges. Gauges are cemented to the surfaces of specimens, which are then brought alternately to temperatures of 35°F and 135°F. Results are accurate to the seventh decimal place.

Jan 6, 1950

By Daniel Martin

THE dendritic pattern of steels shown by deep etching is used exten-sively as a guide in the inspection and control of the great majority of steels used in ordnance construction and for many applications in indus-try. The value of macroexamination lies in the fact that it enables a qualified observer to make deductions concerning the general quality of relatively large pieces of metal. Not the least of these general character-istics is the nature and extent of the dendritic segregation in the steel, either in the cast condition or after mechanical or thermal treatments. PREVIOUS WORK Detailed methods for macroetching were outlined by Yatsevitch1 and have been standardized by the American Society for Testing Materials. A comprehensive study of the occurrence, origin, and the chemical and crystalline nature of the dendritic structure was given by Keshian.2 The marked persistence of dendritic segregation in nickel steels is fully recognized and has been discussed by Sauveur and Reed' and by others. Very little, however, has been written on the effect of the various elements on the macrostructure of steels, and the purpose of this report is to submit evidence concerning the influence of chromium, nickel and molybdenum on the macrostructure of some 4 by 4-in. ingots cast and treated under closely controlled conditions.

Jan 1, 1939

By R. E. Reed-Hill

A simple accurate graphical method for orienting fcc crystals using (111) slip traces on a single surface is described. Solutions placing the pole of the surface in a unit stereographic triangle are obtained using a Wulffnet, a (111) standard projection showing the four (111) planes, and a (111) standard projection ruled into unit stereogmphic triangles. The multiplicity of solutions is described in relation to this method. AN accurate, rapid single-surface technique for orienting fcc crystals, using (111) slip or twin traces, has been a matter of continuing interest, as evidenced by the periodic appearance of papers on this subject.'-4 This note presents a new method possessing some advantages over those previously reported. It is an analog to the technique for hcp metals5 where the solution is based upon a stereographic rotation of the specimen surface on a (0002) standard projection that contains the planes of the possible features that might account for the observed traces. In the hexagonal solution, the axis of rotation is the basal-plane trace in the surface. In the fcc case, the axis of rotation is one of the observed ( 111) slip or twin traces. It has been observed that the solution is greatly facilitated if the indicated movements of the (111) traces during the rotation of the surface are plotted directly on a paper copy of a Wulff net as shown schematically in Fig. 1. The trace selected to represent the axis of rotation is assumed to fall at the north-south poles of the Wulff net. The directions of the other traces are then plotted as points at the proper angles around one-half of the basic circle of the net. The loci of points corresponding to the movements of these traces (directions) during a 90-deg rotation of the surface, about the polar axis of the net, are then easily and accurately drawn by following the appropriate small circles on the Wulff net. The solutions to the problem are obtained with the aid of a (111) standard projection of the (111) planes, see Fig. 2. This is normally a Xerox copy of a carefully drawn master made on high-quality tracing paper. The (111) standard projection is superimposed over the Wulff net and rotated about its center until the points of intersection of the loci of surface traces, drawn on the Wulff net, and the great circles representing the (111) traces, all lie along a common meridian of the Wulff net as demonstrated in Fig. 3. This latter great circle represents a possible position of the surface. The pole of this plane is then plotted on the (111) standard projection. Its location in a unit stereographic triangle may be readily obtained by superimposing (over the standard projection) another tracing paper (111) standard projection subdivided into unit stereographic triangles. The result of this last operation is shown in Fig. 4. MULTIPLICITY OF THE SOLUTIONS The maximum possible number of (111) traces on a single grain surface is four. Any one may be selected as the axis about which the surface is rotated. Corresponding to each such choice are three possible surface-pole orientations, related to each other by a simple 120-deg rotation about the pole of the (111) basic circle. This is a direct result of the threefold symmetry of the (111) standard projection. Since each of the four rotations will normally give a different set of three-pole positions, there are, accordingly, twelve possible solutions. Each of these twelve solutions places the surface pole in the same relative position in a stereographic triangle so that all are crystallo-graphically equivalent. Accordingly, only a single solution is required to obtain a basic orientation of the crystal. It should be noted, however, that the orientations obtained by reflecting* any of these twelve orien- *The reflected orientations may be obtained by a 90-deg rotation of the opposite sense to that shown in Fig. 1. This rotation places the correspond-ing trace loci in the lower hemisphere of the Wulff net rather than in the upper hemisphere. tations through the surface are also possible orientations that could account for the surface traces. Thus, a given set of four traces always corresponds to a pair of basic orientations related by reflection through the specimen surface. This ambiguity can only be re-

Jan 1, 1967

By T. Sterry Hunt

I HAVE already referred to this interesting locality in the opening address, but at the request of some of the members of the Institute, brought before them specimens of the ore and the accompanying rock. The ore, which is cassiterite, is also met with elsewhere in Maine, at Paris and Hebron, but it there occurs associated with orthoclase, quartz, tourmaline, and beryl, in concretionary granite veins, which cut the micaceous gneisses of the White Mountain series. At Winslow the veins traverse an impure gray micaceous limestone, which is found in many parts of this region, and is subordinate to the same gneissic series. The veins, which are seldom more than an inch or two in thickness, are abundant through a considerable breadth of the rock, and are interlaminated with it, occupying places between the sedimentary layers, which are distinctly marked by different shades of color. Occasionally, however, they cut across the stratification for a little distance, showing that the disrupting action was not always confined to tearing the layers apart. The vein-stone consists of purple fluor-spar, and silvery white mica with quartz. In this gangue the cassiterite, nearly black in color, is disseminated in small crystalline masses, sometimes one-half an inch in diameter, and is associated with a little mispickel. I have only seen the veins as exposed at a single point, but was informed that similar veins holding the ore are met with at a distance of several thousand feet

By M. J. Ginsberg, N. A. Gokcen

THE preliminary study of electrochemical desul-furization performed by Ohtani and Gokcen1 left a number of points concerning the process to be investigated. Two of these were i) the determination of the effect of greater current and voltage on the desulfurizing Flower of acid slags (% CaO/% SiO2- 1) and ii) the possibility of the loss of silica in slag by the reactions 2C (in metal) + SiO2 (slag) = Si (in metal) + 2CO(g) and C + SiO2 (in slag) = SiO(g) + cO(g) proceeding to a point at which the composition of the slag was sufficiently altered toward the basic side so a1.s to noticeably affect the rate of de-sulfurization. The apparatus and the procedure used in the present investigation were the same as those used by Ohtani and Gokcen, except the control circuit was connected to 120 v dc instead of 24 v dc and thereby allowed greater freedom in choosing the values of both current and voltage. The graphite crucible containing the melt and serving as the cathode was 3-in. high, and was of 1 1/2-in. ID with a graphite bar of 3/8-in. diam and 8-in. length threaded into the bottom for electrical connection. This was placed into a magnesja outer crucible with a hole in the bottom and alumina insulation was packed between the two crucibles. A charge consisting of 180 g of

Jan 1, 1962

By O. E. Kiessling

THIS announcement of the topics relating to production control, which the Committee hopes to have discussed at the February meeting, supplements the preliminary announcement published in the November number of MINING AND METALLURGY. In the previous article, the writer indicated the kaleide-scopic nature of the questions involved in obtaining better coordination in industry, and that, as a matter of practical expediency, the discussion in February would be limited to the more obvious difficulties in industry which need attention and to those questions which the Committee thinks would be of greatest interest to members of the Institute. But while practical considerations necessitate limiting the program, free discussion of all phases of the subject is urged by 'the Committee. In a preliminary consideration of the production control problem, there loom up two questions which have to be faced: (1) First, there is the question of the extra industrial capacity necessary to meet demand during the ordinary fluctuations of business, commonly characterized as `the "business cycle." Anyone who tries to formulate a program pertaining to productive capacity must decide whether he wishes to discuss the control of business cycles. While this question may eventually lend itself to treatment, the Committee does not feel that it can be considered at present with much profit. (2) The second question arises from the existence of over-stimulated capacity above and beyond peak demands in boom times. Discussion of this topic, it is felt, would be most fruitful. How to prevent capacity from being over-stimulated to an extent beyond any hope of possible demand is a

Jan 1, 1929

By H. H. Reamer, B. H. Sage

The formation volume and the relative volume of the liquid Phase of mixtures of Condensate and gas from five different parts of a field in the Louisiana area have been established experimentally. These studies included gas-condensate ratios as high as 25.000 cu ft/bbl at pressures up to 5,000 psi. The gravities of the tank condensates were between 53.9° and 63.9° API. The compositions of the condensate and gas samples inves-ligated are presented in tabular form. The formation volume. the relative volume of the liquid phase. and the specific volume of the mixtures are available. A rough correlation of the formation volume as a function of pressure. temperature, and gas-condensate ratio has been presented. This correlation i-considered applicable only to the range of conditions covered in this investigation for systems of similar nature and com-position. INTRODUCTION Often a knowledge of the influence of temperature. Pres sure, and relative quantities of condensate and gas upon the volumetric behavior of fluid*. from a given field has been employed in estimating the Conditions existing in the reservoir. The early work of Beecher and Parkhurst' and the more rrcent Studies of the Dominguez' and San Joaqnin Valley Field;: are examples of experimental studies of this character. Correlation of the volumetric behavior of naturally occurring hydrocarbon mixtures has Proved To be feasible' . at low gas-conden-sate ratios-; for fluids*. from a single geographic area. Progres 5 is being made in the Prediction of the volumetric behavior of distillate systems at high gas-condensate ratios and pressure.. However. the estimation of the retrograde". ' dew-point pressure still remains uncertain and probably can best be established by experiment. For this reason it appears of interest to make available experimental information about the volumetric behavior of mixtures of condensate and gas from five different part.; of a single field. This material shows a rough similarity to data for mixtures of condensate and gas from San Joaqnin ' Valley Fields. In the present paper. 110 attempt has been made to coordinate the available information on tbe volumetric behavior of fluids from condensate fields. It appears hopeful that progress can be realized by the utilization of recently developed equa-tions of state.!' However. the primary problem in any such correlation is the proper identification of the components and constituents of naturally occuring systems. Additional experimental information may be required to permit the determination of the values of the constants of the equation of state for References given at end of paper. Manuscriptt received in the office of the Petroleum Branch June 11. 1951. *For present purposes low gas- condensate ratios will he considered as those below 3,000 cu ft/bbl, and the region of high gas-condensate ratio will be limited to compositions containing more than 5,000 cu ft of pas per bbl of condensate. Mixtures Containing between 3,000 and 5.000 CII ft OF gas per bbl will be considered of intermediate gas-condensate ratio.

Jan 1, 1952

By M. R. Meyer, W. T. Walter

A great deal is known, in a qualitative sense, about the performance of CMI EB-36 centrifuges. The manufacturer can give reliable guidance for the proper operation of its centrifuges and can give general estimates of expected product moisture and recovery. Quantitative estimates of the effects of changes in the various operating parameters are more difficult to find. The engineer faced with designing a preparation plant may be without the specific data needed to make decisions. For example, to obtain optimum product moisture when drying 9.5 mm X 595 µm (0.4 in. x 28 mesh) coal the centrifuge manufacturer recommends having no more than 5% -595 µm (-28 mesh) material in the centrifuge feed. They know that more -595 µm (-28 mesh)material in the feed will cause higher product moistures, but they usually cannot quantify the increased moisture or describe the shape of the product moisture versus -595 µm (-28 mesh) in the feed curve. This study was conceived to provide quantitative information on the EB-36 centrifuges, focusing on product moisture, recovery, and size degradation. All of the centrifuges tested were Model EB-36 dryers from Centrifugal and Mechanical Industries Inc. (CMI), with feeds in the nominal 9.5 mm x 595 pm (0.4 in. x 28 mesh) range. These are typical centrifugal dryers in this application, and many were available for testing.

Jan 1, 1984

By K. Matsuda, H. Tanaka, M. Mamiya, H. Majima

Copper cementation was studied from both thermodynamic and kinetic aspects. The temperature effect of copper cementation, which has been recognized as an anomalous result, and the rate enhancement phenomenon observed after the initial linear step are, in particular, focused in this work. The main results obtained are as follows; 1) Free energy changes of copper cementation reactions, calculated by the use of the "Correspondence Principle" of Criss and Cobble are rather insensitive to temperature. 2) A Flow-cell assembly consisting of a special cupric ion electrode, a calomel electrode and a potentiometer is particularly useful for the continuous measurements of copper cementation rate. 3) Two first-order reaction rate constants for the CU2+- Fe system were successfully determined by the use of the flow-cell assembly. 4) Activation energies determined for the initial rate and the 9 maximum rate of CU2+ - Fe system are both 4.6 kcal/mole. This fact suggests that the mechanisms of the initial reaction and the final reaction are essentially the same and both reactions are rate controlled by the diffusion in a boundary layer. The difference in the rate constants of them may fie explained by the effect of the nature of surface deposits. 5) Qualitative explanation of the rate enhancement phenomenon from the initial rate was successfully made by applying Bockris "Penetration Model."

Jan 1, 1976

By Charles F. Manness

In the great increase of product which has been accomplished in the American Bessemer plant, through improvements in machinery and refractories, and by more perfect skills in their manipulation

Jan 1, 1881

By James M. Riddle

INTRODUCTION Block-caving mines are generally large operations. Calculating the quantity and value of mineral present and determining the economic limits to mining are complicated processes requiring much time and effort. If these processes are to be worthwhile, they must be accurate and reliable. Success in planning may increase the economic returns significantly. Since capital investments in block-caving mines are generally quite large, and development may span several years, quicker and more accurate methods of mine layout are very worthwhile to the mining industry. The purpose of this study is to develop an approach to the evaluation and layout of block-caving mines. The study included development of a simple approach to modelling ore reserves and a rapid, dynamic programming solution for optimum ultimate mining limits. TRADITIONAL APPROACHES TO BLOCK-CAVING MINE LAYOUT General discussion of techniques of calculating and valuing ore reserves can be found in the literature, (1-4). Mining limit approaches have been investigated by many and follow five general methods: 1, Moving cone method (5) 2. Graphroriented technique (6,7) 3. Dynamic programming technique (7,8,9) 4. Network flow method (10,11) 5. Pillar method (12) Of these investigations, only two were developed for underground mining applications, those of Sharp (9) and Riddle (11).

Jan 1, 1977

By A. T. Tye

WHEN the roughing tables operated in 1923 were abandoned, all the coarse iron pyrite for-merly removed by the tables had to be ground to flotation size, which caused an increased power con-sumption of 2 kw.-hr. per ton. Recently, by increasing the tonnage, this has been reduced to a total of 16.6 kw.-hr. per ton. The cost of repairs has been slightly reduced by using an alkaline circuit instead of the acid mine water used in 1923. Other economies from elim-inating roughing tables and the finishing tables have more than compensated for the extra grinding and the total costs have remained practically the same, until the first part of 1927, when, with increased tonnage, the total cost has decreased to 72 cents and the repair cost to 9 cents. In 1923, with a combined gravity and bulk flotation flowsheet, the grade of concentrate was only 4.38 per cent copper. With preferential flotation this has in-creased to over 17 per cent copper. The tailing has decreased from 0.29 per cent -copper to 0.18 per cent. The copper recovery, instead of decreasing; as might be expected, has increased from 87.4 per cent to, 91.5 per cent. The silver recovery has also increased from 88

Jan 8, 1927

By W. C. Leslie

The textures of cold-rolled and of annealed iron are compared with those of an iron-0.8 pct copper alloy in which the amount of precipitation after cold rolling was controlled. Previously published pole figures -for cold-rolled and for annealed iron are confirmed. The effects of precipztatiotz after cold rolling are to retain the cold-rolled texture after annealing, to inhibit the formation of the usual allnealing texture, and to produce elongated recrys-tallized ferrite grains. It is suggested that the inhibition of new textures by precipitation after cold rolling is a general phenomenon. A great deal of attention has been paid to the development of texture during the secondary or tertiary recrystallization of ferritic alloys, but very little work seems to have been done on the control of texture during primary recrystallization. If such control were attained, it might be possible to simplify the processing of oriented materials or to change the characteristics of current cold-rolled and an-nealed products. From previous experience, it seemed likely that texture could be controlled by recrystallizing a supersaturated solid solution. Green, Liebmann, and Yoshidal found that the formation of preferred orientation in aluminum (40 deg rotation about <111> relative to the deformed matrix) was inhibited when iron was retained in supersaturated solid solution in the strained aluminum. The authors attributed this inhibition to iron atoms in solid solution. There is, however, an alternative explanation. Green et al, took a highly supersaturated solution of iron in strained aluminum and heated it to an unspecified temperature for recrystallization. It is probable that precipitation occurred prior to and during recrystallization, and it is proposed that the inhibiting agent is this precipitate, rather than the iron atoms in solid solution. It is important to note that precipitation before cold work is ineffective; the effective precipitate is that formed after cold working and either before or during recrystallization. The location and distribution of the precipitate are critical. Precipitation in such a manner has been found to have profound effects upon kinetics of recrystallization and the microstruc-ture of the recrystallized alloys.2-4 It would be surprising, indeed, if this were accomplished with no change in texture. Because of the relative simplicity of the system, and because of previous experience,4-7 it was decided to determine the effect of precipitation on texture in an alloy of iron and copper. Bush and Lindsay5 found an unspecified change in texture in cold-rolled and annealed low-carbon rimmed steel sheets when the copper content exceeded 0.1 pct. MATERIALS In earlier work, the rate of recrystallization of a low-carbon steel was greatly decreased by 0.80 pct copper, and, after the proper treatment, the recrystallized ferrite grains were greatly elongated.4 Accordingly, it was decided to investigate the effect of precipitation on texture at this level of copper content. The iron and the iron-copper alloy were made from high-quality electrolytic iron and OFHC copper, vacuum-melted in MgO crucibles, cast, hot-rolled to 0.2 in., then machined to 0.150 in. The compositions are given in Table I. The plates were heated to 925°C and brine quenched, twice. This produced a ferrite grain size of ASTM 0 in the iron and ASTM 1 in the Fe-Cu alloy. Disk specimens were cut from the heat-treated plates, repeatedly polished and etched, then used to determine (110) and (200) pole figures by reflection. Despite the complication of large grain size, these pole figures strongly indicated a random texture. PROCEDURES The copper content in solid solution in ferrite before cold rolling and recrystallization, and hence, the amount that could precipitate during the recrys-tallization anneal, was controlled at three levels by heat treatment. The specimens as quenched from 925° C were presumed to have all the copper, 0.80 pct, in solid solution. Other samples of the quenched alloy were aged 5 hr at 700°C to retain about 0.5 pct Cu in solid solution.6 A third set of quenched specimens was reheated to 700°C, then slowly cooled in steps, to reduce the amount of copper in solid solution to a very low level. All specimens were cold-rolled 90 pct, from 0.150 to 0.015 in. thick. The rolling was done in one direction only, i.e., the strip was not reversed between passes, with a jig on the table of the mill to keep the short specimens at 90 deg to the rolls. The rolls were 5 in. in diameter and speed was 35 ft. per min. Machine oil was used as a lubricant. In a supersaturated alloy, the maximum effect of the copper precipitate on microstructure and on recrystallization can be developed by a treatment at 500°C, after cold rolling and before recrystallization.&apos;

Jan 1, 1962

By George Krauss, Morris Cohen

NUMEROUS investigators1-4 have shown that one of the most conspicuous effects of the reverse marten-sitic transformation in Fe-Ni alloys is the stabilization of the austenite which forms on reversal. However, the present authors5 found a virtual absence of stabilization in a recent study of this subject. The purpose of this note is to account for the discrepancy.

Jan 1, 1963

By H. M. Fisher, R. E. Snow, S. C. Sun

SEVERAL constructive and fundamental studies have been made in the analysis of data obtained from experiments carried on with batch ball and rod mills. The operating characteristics of ball milling in small continuous circuits have also been appraised. It is from these analyses that some of the theories of comminution have been developed. Relatively few studies of continuous rod milling have added significantly to the fundamental concepts, because seldom have they yielded sufficiently consistent results. Perhaps they have been too limited in their scope. Careful control of the variables in batch grinding is simple compared with that encountered in a continuous operation. This factor alone has discouraged many investigators. Occasionally results of systematic changes made in industrial rod mill circuits have been published, but usually the data are sketchy and are restricted because of the unwieldiness of the equipment used. The work, in general, has not been comprehensive; nevertheless it has provided empirical relationships that have bridged the gap between postulate and practice so that by proper manipulation of formulae, a mill designer can anticipate mill size and power requirements.14 Although operating variables of a small continuous mill are not so easy to control as with the batch mill, with present day devices, and with careful experimental work, consistent results can be obtained. Nearly four years ago, in the Process Laboratory, Allis-Chalmers Mfg. Co. began a systematic study of the effects of several variables upon the performance of the pilot rod mill. A mill was built in the laboratory to provide the versatility required for the proposed study. It was constructed in sections so that it could be operated, with a few modifications, as a rod mill 30 in. x 8 ft or 30 in. x 4 ft. The discharge end of the shell was flanged so that either an end peripheral discharge or an overflow discharge could be installed. Thus the performance of at least four types of mills could be studied merely by changing the type of discharge or the length of the mill shell. The grinding experiments were designed so that a study could be made of the way in which the mill speed, feed rate, and pulp density influenced the performance of both overflow and end peripheral discharge rod mills. Four sets of experimental data were collected from the four mill arrangements. The mill in each set of experiments was fed at four rates of feed depending on the length of the mill, at four pulp densities, and at five percentages of critical speed. Electrical and mechanical controls were in- stalled to regulate all these independent variables, and auxiliary devices were used to verify the precision of the controls at each point. The dependent variables used to quantify the experiments were the reduction ratio and the hew surface area produced as calculated from sieve analyses. These were incorporated with the energy factor by the calculation of both the new surface produced per unit of energy and the Bond work index.&apos; Rod wear, as a dependent variable, was not studied because of the short period of operation for each run. Exclusive of repeat runs, each set of experiments yielded 80 products, and the total study at least 320 products, all of which were quantified. With the operating information collected, these data presented a bewildering accumulation. Statistical analysis has been invaluable in unraveling the confusion and in presenting a means of establishing the nature and the magnitude of the significant variables. Data presented in this paper are those from the 30 in. x 4 ft end peripheral discharge rod mill, Fig. 1, when limestone was ground at feed rates of 1000, 2000, 4000, and 5000 lb per hr, at pulp densities of 50, 60, 70, and 80 pct solids, and at mill speeds of 50, 60, 70, 80, and 90 pct of the critical speed. These 80 tests have all been run at least twice, and occasionally a third time, to prove that the data obtained were reproducible. The techniques of operation and the methods of quantification of results are described in the following pages and the results analyzed statistically to show the significant variables. The variables are plotted to show the relationships that exist. A massive dolomitic limestone from Waukesha Lime and Stone Co. was used for feed during these experiments because of its availability and its tex-tural uniformity. This limestone analyzed 28.7 pct CaO, 21.0 pct MgO, 6.0 pct SiO2, 0.4 pct A1²O³, and 0.3 pct Fe²O³ and had a loss on ignition of 44.1 pct. It had a rod mill grindability at 14 mesh of 9.6 grams per revolution from which a work index of 13.9 was calculated. The ball mill grindability at

Jan 1, 1955