Search Documents

By D. H. Woodard, G. W. Geil, W. D. Jenkins

In a series of papers, the authors and their associates have shown the influence of four important factors on the technical cohesion limit.3-l6 By "technical cohesion limitv is meant the technically determin-able resistance to fracture. The four importarlt factors are the stress system, plastic deformation, temperature, and the strain rate, The influence of any one of these factors may be represented by a curve of cohesion limits, although only one point on the curve may represent actual fracture. As the term "fracture stress" has come into general use with the same significance as technical cohesion limit, the authors are here using the shorter term with the understanding that it does not always refer to actual fracture. The previously mentioned series of papers contains ample evidence that plastic extension increases the fracture stress of any polycrystalline metal, In a recent paper of the series,l5 moreover, it has been shown that the effect of plastic deformation on the fracture stress cannot be attributed to reorientation of internal flaws but is a work-strengthening effect, similar to the effect on the flow stress, $ Plastic deformation of steels, however, may not only cause work hardening, but may result in additional hardness because of strain aging. Some evidence that strain aging affects not only the flow stress but also the fracture stress, has been presented in a recent paper.14 In that paper, a study is made of the influence Of Plastic deformstion at room temperature on the fracture stress of ferritic steels at -188°C. The study is based on the results Of two-stage tests. In the first stage each specimen was extended a predetermined amount at room temperature; in the second stage the specimen was tested to fracture in liquid air. In most Of these tests the specimen remained in the testing machine during the interval of about one hour between the first and second stages, it was kept under a tensile load of about 500 lb and maintained at liquid air temperature. The effects of various amounts of .plastic deformation on the fracture stress were thus determined and curves were obtained to represent the influence of plastic deformation at room temperature on the stress at brittle fracture in liquid air.14 Two specimens Of ingot iron, however, were removed from the testing machine at the end of the first stage and several days elapsed before the specimens were tested to fracture in liquid air, As shown in Fig 8 of that paper," the points representing fracture of these specimens are far above the curve representing the results of two-stage tests without a rest interval between the stages. The evidence thus indicated that the fracture stresses of these two specimens were increased not

Jan 1, 1949

By G. W. Geil, D. H. Woodard, W. D. Jenkins

In a series of papers, the authors and their associates have shown the influence of four important factors on the technical cohesion limit.3-l6 By "technical cohesion limitv is meant the technically determin-able resistance to fracture. The four importarlt factors are the stress system, plastic deformation, temperature, and the strain rate, The influence of any one of these factors may be represented by a curve of cohesion limits, although only one point on the curve may represent actual fracture. As the term "fracture stress" has come into general use with the same significance as technical cohesion limit, the authors are here using the shorter term with the understanding that it does not always refer to actual fracture. The previously mentioned series of papers contains ample evidence that plastic extension increases the fracture stress of any polycrystalline metal, In a recent paper of the series,l5 moreover, it has been shown that the effect of plastic deformation on the fracture stress cannot be attributed to reorientation of internal flaws but is a work-strengthening effect, similar to the effect on the flow stress, $ Plastic deformation of steels, however, may not only cause work hardening, but may result in additional hardness because of strain aging. Some evidence that strain aging affects not only the flow stress but also the fracture stress, has been presented in a recent paper.14 In that paper, a study is made of the influence Of Plastic deformstion at room temperature on the fracture stress of ferritic steels at -188°C. The study is based on the results Of two-stage tests. In the first stage each specimen was extended a predetermined amount at room temperature; in the second stage the specimen was tested to fracture in liquid air. In most Of these tests the specimen remained in the testing machine during the interval of about one hour between the first and second stages, it was kept under a tensile load of about 500 lb and maintained at liquid air temperature. The effects of various amounts of .plastic deformation on the fracture stress were thus determined and curves were obtained to represent the influence of plastic deformation at room temperature on the stress at brittle fracture in liquid air.14 Two specimens Of ingot iron, however, were removed from the testing machine at the end of the first stage and several days elapsed before the specimens were tested to fracture in liquid air, As shown in Fig 8 of that paper," the points representing fracture of these specimens are far above the curve representing the results of two-stage tests without a rest interval between the stages. The evidence thus indicated that the fracture stresses of these two specimens were increased not

Jan 1, 1949

By J. J. Rutledge

THE first method of working coal mines in the middle western states, more particularly in Illinois, Indiana and Missouri, was by means of the so-called single-entry method. In this method a single main passageway, or entry, was driven in the coal seam. with no parallel passageways, and from this pas-sageway or entry there were turned at intervals sim-ilar cross-passageways or entries, and from these cross-passageways, if the coal seam worked lay fairly horizontal, rooms were turned right and left. These crude methods of working were followed when the com-panies opening the mines were small and of very limited capital, and when the demand for coal was small and irregular. The principal desire was to produce coal in the short-est possible time and at the cheapest price. The chief evil resulting from such method of working was de-fective ventilation, although there were other serious drawbacks. There were then few or no good mining laws and no restrictions on those operating the coal mines. The hours of labor were long, the wages low, and the miners accordingly worked hard. All the coal was either sheared or undercut with a pick by hand. Very little solid shooting and no machine mining was done. What little air entered the mine, openings was introduced through the entries or. headings and thence conducted through the rooms by means of curtains; in many cases, as the workings became more exten-sive, the number of curtains added so materially to the mine resistance that ventilation was extremely in-efficient. Shots were fired by the miners at any time during the working shift and consequently there was more or less powder smoke or fumes in the mine work-ings all day long. Moreover, the working days were much longer than at present. The fine, dry coal-dust falling from the miners' picks while they were shear-ing or undercutting the coal filled the mine atmosphere and was taken into the lungs of the mine employees.

Jan 2, 1927

Jan 1, 1970

By A. Vifian, I. lwasaki

Several samples of copper-nickel ore from the Duluth Gabbro were studied to relate their mineral-ogical characteristics with their amenability to concentration by flotation. The most common rocks in the samples were norites, gabbros, and troctolites. The texture of the rocks varied from coarse pegma-titic to very fine. The copper contents ranged from 0.2-0.7% and the nickel contents from 0.07-0.15%. The ore minerals were chalcopyrite, cubanite, pyrrhotite, and pentlandite. Most of the ore minerals occurred in interstices between laths of plagioclase, but some were included in the gangue grains. The samples responded readily to xanthate flotation. After a 65 to 100-mesh grind about 95% of the copper and 85% of the nickel were recovered in a bulk sulfide concentrate. Such recoveries remained constant even with grinds as fine as 270 mesh due to the extremely fine inclusions of sulfides in the silicate gangue. A finer grind than 270 mesh was necessary to free the copper-iron sulfides from the nickel-iron sulfides. A combination of time and British gum* was quite effective in producing concentrates analyzing 25-30% copper. The nickel concentrate averaged 1.5% nickel. Most of the nickel lost in the tailing was present as un-liberated sulfides and not as nickel in the olivine structure. The nickel content of the olivine was only about 0.05 or 0.08%. Western world nickel usage in 1967 is expected to be the second highest on record, amounting to 825 million lb. Despite a rise in mine production, however, demand is expected to exceed supply in 1968. ' Hence, exploration, development, and production expansion projects are being accelerated on a world scale. In Minnesota the copper-nickel bearing Duluth Gabbro is receiving much attention. During the past year 11 companies have been granted leases in the region, and the 1967 Minnesota legislature enacted a tax law designed to encourage the development of a copper-nickel industry. Although it is only during the past few years that mining companies have shown an active interest in the Minnesota copper-nickel deposit, copper-nickel minerals have been known to exist in northeastern Minnesota since 1899.3 At the 28th Mining Symposium, Dr. P. K. Sims, from the Geological Survey of Minnesota, gave a review of copper-nickel exploration in northeastern Minnesota,4 in which he emphasized that the potential of the Duluth Gabbro complex is large. Tests on samples from the Kawishiwi River area were reported by the United States Bureau of Mines in 1955.' In 1964, the Mines Experiment Station described tests on samples from the Gunflint Trail: and in 1966 the Minnesota Geological Survey published a geological map of the Gabbro Lake Quadrangle. The Mines Experiment Station published a study of the concentration of a Minnesota copper-nickel ore in 1967.7 The present paper is divided into three parts. The first describes the mineralogy of some rock samples from the Kawishiwi River area of northeastern Minnesota; the second summarizes the results of numerous flotation tests that were made on the samples, and the third explains the loss of nickel in the flotation tailing. MINERALOGY OF KAWlSHlWl ROCKS Recently five samples of mineralized gabbro from the Kawishiwi River area, a few miles east of Ely, were received at the Mines Experiment Station. One of the samples was a 175-lb composite, which was designated Ore 1556. The other four samples were 7-lb grab samples that had been obtained from four different exploration pits. They were designated Ore 1626, Lots 1 through 4. Basic Mineralogy: Many authors have reported that the rocks of the so-called gabbro of the Duluth Intrusion vary widely in composition.8-9 The samples on which our studies were based also contained a wide range of rocks. A gabbro, olivine-gabbro, anorthosite-gabbro, norite, and a troctolite were represented. The essential minerals in the samples were plagio-clase, pyroxene, and olivine, in variable proportions.

Jan 1, 1969

By Emile Gyss

THE speed of drilling rock has become an impor-tant factor in mining operations, while the place-ment of holes, kind, and quantity of explosive used. are equally important. These are a function of the rock hardness and toughness. Both of these fac-tors must be considered in compiling a table that will enable a mine operator or engineer to estimate drilling speeds in a given rock, knowing its hardness, and from its toughness, the dynamite required. The hardness of a homogeneous rock may be defined as its resistance to a penetrating medium, such as a drill-steel bit, and toughness, its resistance to with-stand rupture by the tearing apart of its minerals or parts of the same mineral. Rock hardness, as it has here been defined, is a function of the hardness of the component grains composing it, as well as grain size, shape, arrangement, and binding minerals. Rock tough-ness depends on substantially the same factors, but is measured by a totally different method. The units in which rock hardness is usually ex-pressed are either relative values or alphabetical desig-nations which carry no definite quantitative meaning. R. M. Raymond has suggested the measurement of com-posite rock hardness, based on mineral hardness as ob-tained by the Moh scale. This is done by multiplying the percentage of each mineral in a rock by the Moh mineral hardness and dividing by 100. These values convey a clearer conception in the minds of men in-terested in rock work -and are the basis of the units used in Tables 1 and 2. The hardness of rocks as it has been variously de-fined may be determined by different methods. The first method is one in which the proportionate average of the hardness of minerals making up a rock is the basis for classification. The other factors of grain size, shape, arrangement, and binding power are not considered.

Jan 6, 1927

By W. W. Tyler, A. C. Wilson, L. B. Nesbitt

INVESTIGATIONS of thermal conductivity and impact strength of the titanium alloy RC-130-B and 316 stainless steel were undertaken because of interest in strong, nonmagnetic, commercially available alloys of low thermal conductivity for use in low temperature experiments. Measurements of electrical resistivity and thermoelectric power were also made for some of the samples studied. The titanium alloy designated as RC-130-B is manufactured by Rem Cru Titanium Inc. It contains 0.14 pct C, 3.99 pct Al, and 4.7 pct Mn. A general discussion of properties of the two phase Ti-4Mn- 4A1 alloys is given by Finlay and Vordahl.' The alloy is machinable and has a yield strength greater than 130,000 lb per sq in. at 0.2 pct offset. The 316 stainless steel sample used for both conductivity and impact strength measurements was obtained from the Allegheny-Ludlum Steel Corp. and is designated as Allegheny metal 18-8M, Type 316, Grade 316. The sample had received 25 pct minimum final cold reduction and had a Brine11 hardness rating of 255. Several impact tests were made on a sample of 316 stainless which had not received the 25 pct cold reduction. Also several data points are reported giving thermal conductivity and electrical resistivity for a sample of 304 stainless steel taken from stock. Figs. 1 and 2 give thermal conductivity and electrical resistivity data for the titanium alloy and for

Jan 1, 1954

By W. F. A. Thomae

The Villayet of Aidin is a province in Asia Minor which has a coast line extending from opposite the island of Mitylene to beyond Makri, opposite the island of Rhodes, and embraces almost the entire basins of the two principal rivers, the Sarabat

Jan 1, 1899

By Alfred Boyles

The experiments described below are a continuation of work on the graphitization of cast iron conducted as part of the program of fundamental research at Battelle Memorial Institute. In previous work it was found that melting in hydrogen increased the amount of eutectic carbide appearing in certain alloys and in others produced marked changes in the size of the graphite flakes. These effects seemed to be closely related to the amount of sulphur and manganese present in the material studied. Iron-carbon-silicon alloys did not respond to hydrogen in the same manner as cast iron and there was no evidence to show that hydrogen was able to stabilize the carbide in such alloys unless additions of sulphur were made. The two alloys examined contained about 2 per cent of silicon. The present paper is concerned with alloys of lower silicon content and describes the structural changes produced by melting in various atmospheres at pressurcs ranging from a partial vacuum up to 300 lb. per sq. inch. Experimental Method The experimental technique was similar to that previously employed, so that direct comparison might be made with earlier work. Alloys were

Jan 1, 1939

By Alfred Boyles

The experiments described below are a continuation of work on the graphitization of cast iron conducted as part of the program of fundamental research at Battelle Memorial Institute. In previous work it was found that melting in hydrogen increased the amount of eutectic carbide appearing in certain alloys and in others produced marked changes in the size of the graphite flakes. These effects seemed to be closely related to the amount of sulphur and manganese present in the material studied. Iron-carbon-silicon alloys did not respond to hydrogen in the same manner as cast iron and there was no evidence to show that hydrogen was able to stabilize the carbide in such alloys unless additions of sulphur were made. The two alloys examined contained about 2 per cent of silicon. The present paper is concerned with alloys of lower silicon content and describes the structural changes produced by melting in various atmospheres at pressurcs ranging from a partial vacuum up to 300 lb. per sq. inch. Experimental Method The experimental technique was similar to that previously employed, so that direct comparison might be made with earlier work. Alloys were

Jan 1, 1939

By W. R. Crane

The support of roof in mines is dependent largely on the character of the top rock and its occurrence. The formations overlying the orebed in the Birmingham district are sandstone and slate. The sandstone occurs in beds of sufficient thickness to constitute important elements in the system of support; the slate is relatively strong but is thinly stratified. The alternating beds of sandstone and slate furnish an excellent combination in that the former are strong and the latter are impervious; however, their continuity is broken by jointing or slip planes. The thickness, and consequent weight of the overlying formations, is important in so far as the size and arrangement of pillars are concerned but may be relatively unimportant, temporarily at least, as a factor in the support of the roof. The position of the respective beds of sandstone and slate, their relative thickness, and their inherent weakness because of the occurrence of faults and folds, may exert a predominating influence on their support in place, which is affected only in part by the weight of the cover. The only mine in this district that operates under a cover of approximately 2000 ft. (1900 ft.) is the Shannon so-called "twin slope," situated 14,000 ft. southeast of the portal of the No. 7 mine of the Tennessee Coal, Iron, & Railroad Co. The conditions in this mine indicate what may be expected in other mines when the same depth is attained; in fact, the effect of pressure is shown in several mines that have not reached two-thirds of that depth. It is evident, then, that conditions affecting the support of roof will not improve but rather will become more difficult with the extension of the mines into the valley under a constantly increasing weight of cover. Further, the difficulties will probably be augmented by the occurrence of faults and other disturbed ground, the presence and position of which at present are largely unknown.

Jan 1, 1925

By J. W. Pamplin

Some 40 miles east of Tampa is the center of the Florida pebble phosphate deposits. These are of Pliocene age and consist of several members of the Bone Valley formation.1 Physically the phosphate-bearing formation, locally called the "matrix," varies in thickness from nothing to about 25 ft., usually averages 10 ft., and consists mainly of clay, quartz and phosphate pebble, the latter particles varying in size from colloidal to one inch diameter. The pebbles range in color from dark gray, through white, to cream, and in hardness from that which must be broken with a hammer to that which can be scratched with the fingernail. They assay from 66 to 80 per cent bone phosphate of lime (called "B.P.L." in the trade) or tricalcium phosphate (Ca³P2O8) and are secondary apatites. They form from 15 to 50 per cent by weight of the matrix. Over the matrix lies a varying thickness (5 to 40 ft.) of overburden composed of quartz and clay. Briefly, mining consists of two operations2 in open pits about 200 ft. wide by 1/2 mile or more in length. In the first step overburden is removed by large electric draglines at the rate of about 700 cu. yd. per hour. This is followed closely by hydraulic mining of the matrix at the rate of about 300 cu. yd. per hour. This matrix yardage is moved from an improvised sump in the floor of the pit to an ore-dressing plant, sometimes a mile distant, by one, two or three "pit-cars" (pumping units) working on a 12-in. pipe line called the "rock line" to distinguish it from the high-pressure water line feeding the hydraulic giants, which is known as the "hydraulic line." This 700 yd. of overburden and 300 yd. of matrix—1000 yd. in all-amounts to about 1500 tons of material moved each hour. The overburden is dumped into the mined-out pit alongside the pit being mined. The matrix moves to the ore-dressing plant at the rate of about 7% long tons in 4000 gal. of water per minute—a ratio of approximately one to two by weight, or one to six by volume. This constitutes the "mill heads," but in the pebble district it is called the "matrix."

Jan 1, 1938

By J. W. Pamplin

Some 40 miles east of Tampa is the center of the Florida pebble phosphate deposits. These are of Pliocene age and consist of several members of the Bone Valley formation.1 Physically the phosphate-bearing formation, locally called the "matrix," varies in thickness from nothing to about 25 ft., usually averages 10 ft., and consists mainly of clay, quartz and phosphate pebble, the latter particles varying in size from colloidal to one inch diameter. The pebbles range in color from dark gray, through white, to cream, and in hardness from that which must be broken with a hammer to that which can be scratched with the fingernail. They assay from 66 to 80 per cent bone phosphate of lime (called "B.P.L." in the trade) or tricalcium phosphate (Ca³P2O8) and are secondary apatites. They form from 15 to 50 per cent by weight of the matrix. Over the matrix lies a varying thickness (5 to 40 ft.) of overburden composed of quartz and clay. Briefly, mining consists of two operations2 in open pits about 200 ft. wide by 1/2 mile or more in length. In the first step overburden is removed by large electric draglines at the rate of about 700 cu. yd. per hour. This is followed closely by hydraulic mining of the matrix at the rate of about 300 cu. yd. per hour. This matrix yardage is moved from an improvised sump in the floor of the pit to an ore-dressing plant, sometimes a mile distant, by one, two or three "pit-cars" (pumping units) working on a 12-in. pipe line called the "rock line" to distinguish it from the high-pressure water line feeding the hydraulic giants, which is known as the "hydraulic line." This 700 yd. of overburden and 300 yd. of matrix—1000 yd. in all-amounts to about 1500 tons of material moved each hour. The overburden is dumped into the mined-out pit alongside the pit being mined. The matrix moves to the ore-dressing plant at the rate of about 7% long tons in 4000 gal. of water per minute—a ratio of approximately one to two by weight, or one to six by volume. This constitutes the "mill heads," but in the pebble district it is called the "matrix."

Jan 1, 1938

Jan 1, 1969

By J. S. Billheimer, B. H. Sage, W. N. Lacey, C. G. Yundt

As a part of a general investigation of the separation of bitumen from hydrocarbon mixtures a study was made of a restricted quaternary system composed of methane, decane, tetralin, and bitumen. The work was limited to a pressure of 8000 psi, a temperature of 220 °F, and to a fixed relative proportion of decane, tetralin, and bitumen. The measurements permitted the determination of the distribution of these components in each of the fluid phases. It was not possible to distinguish a second liquid phase in the course of these measurements. Gas-liquid equilibrium "constants" of each of the components were found to vary markedly with the composition of the system while temperature and pressure remained fixed. INTRODUCTION The separation of bitumen frorn naturally occurring hydrocarbon mixtures has been of importance for a number of years in the production of petroleum, especially in the California area. The deposition of this material from crude oils was noted in earlier studies of the solubility of natural gas in crude oil.¹,²,3 Studies of the separation of bitumen from crude oils from the Greeley and Santa Fe Springs fields were carried out."." The behavior of these systems appeared complex and studies of two restricted ternary systems involving mixtures of n-pentane, tetralin, and bitumen,' and of decane, tetralin; and hitumen, confirmed this belief. Reviews of the literature pertaining to the separation of bitumen from naturally occuring and refined hydrocarbons are available." The important effect of methane in the separation of bitu- men from naturally occurring hydrocarbon mixtures was apparent from the earlier studies and for that reason it appeared desirable to investigate a restricted quarternary system involving mixtures of methane. decane, tetralin, and bitumen; data concerning the behavior of mixtures of decane. tetralin. and bitumen having already been obtained.V his study was restricted to a pressure of 8000 psi," a temperatue of 220° F, and fixed relative proportions of bitumen, decane. and tetralin. This composite constituent, hereinafter designated as the less volatile constituent, was made up of 0.0455 weight fraction bitumen. 0.0909 weight fraction decane, and 0.8636 weight fraction tetralin. The experimental method involved bringing together mixtures of methane and the less volatile constituent in varying proportions in a constant volume container at the pressure and temperature indicated above. The composition of each of the phases was determined and from this the extent of the separation of bitumen was established. MATERIALS The bitumen used in this investigation was obtained from the same stocks employed in earlier studies. The crude material from the North Coles Levee field was stored in the laboratory] in a closed drum for a period of five years. Several samples from this stock were subjected to refining operations which were described earlier,' and every effort was made to follow the same procedure in all cases. It was necessary to prepare supplies of bitumen for this investigation at two rather widely different times. These materials have been identified as samples 1 and 2. The composition of the crude bitumen after it was washed with n-pentane at room temperature

Jan 1, 1949

By W. N. Lacey, C. G. Yundt, B. H. Sage, J. S. Billheimer

As a part of a general investigation of the separation of bitumen from hydrocarbon mixtures a study was made of a restricted quaternary system composed of methane, decane, tetralin, and bitumen. The work was limited to a pressure of 8000 psi, a temperature of 220 °F, and to a fixed relative proportion of decane, tetralin, and bitumen. The measurements permitted the determination of the distribution of these components in each of the fluid phases. It was not possible to distinguish a second liquid phase in the course of these measurements. Gas-liquid equilibrium "constants" of each of the components were found to vary markedly with the composition of the system while temperature and pressure remained fixed. INTRODUCTION The separation of bitumen frorn naturally occurring hydrocarbon mixtures has been of importance for a number of years in the production of petroleum, especially in the California area. The deposition of this material from crude oils was noted in earlier studies of the solubility of natural gas in crude oil.¹,²,3 Studies of the separation of bitumen from crude oils from the Greeley and Santa Fe Springs fields were carried out."." The behavior of these systems appeared complex and studies of two restricted ternary systems involving mixtures of n-pentane, tetralin, and bitumen,' and of decane, tetralin; and hitumen, confirmed this belief. Reviews of the literature pertaining to the separation of bitumen from naturally occuring and refined hydrocarbons are available." The important effect of methane in the separation of bitu- men from naturally occurring hydrocarbon mixtures was apparent from the earlier studies and for that reason it appeared desirable to investigate a restricted quarternary system involving mixtures of methane. decane, tetralin, and bitumen; data concerning the behavior of mixtures of decane. tetralin. and bitumen having already been obtained.V his study was restricted to a pressure of 8000 psi," a temperatue of 220° F, and fixed relative proportions of bitumen, decane. and tetralin. This composite constituent, hereinafter designated as the less volatile constituent, was made up of 0.0455 weight fraction bitumen. 0.0909 weight fraction decane, and 0.8636 weight fraction tetralin. The experimental method involved bringing together mixtures of methane and the less volatile constituent in varying proportions in a constant volume container at the pressure and temperature indicated above. The composition of each of the phases was determined and from this the extent of the separation of bitumen was established. MATERIALS The bitumen used in this investigation was obtained from the same stocks employed in earlier studies. The crude material from the North Coles Levee field was stored in the laboratory] in a closed drum for a period of five years. Several samples from this stock were subjected to refining operations which were described earlier,' and every effort was made to follow the same procedure in all cases. It was necessary to prepare supplies of bitumen for this investigation at two rather widely different times. These materials have been identified as samples 1 and 2. The composition of the crude bitumen after it was washed with n-pentane at room temperature

Jan 1, 1949

Jan 1, 1947

Jan 1, 1947

By Lester A. Blackner

The Ray Consolidated Copper Co.'s mining property is located on Mineral Creek, 6 miles north of Kelvin, at Ray, Pinal County, Ariz. (Fig. 1). The mining claims now owned by the company consist of 126 lode claims, comprising 2,144.9 acres, containing at the beginning of operations 82,904,368 tons of 2.19 per cent. copper ore. General Characteristics of the Orebody The main orebody is a disseminated deposit in schist and porphyry formed by secondary enrichment. Its existence was proved by churn drilling, and it is at present one of the largest proved copper deposits in the world. The orebody itself covers 205 acres with an average thickness of 121 ft., and occupies a definite belt which has a northwest direction. Its length is approximately 5,000 ft. The width varies, being about 2,000 ft. at the west end and 2,500 ft. at the east, narrowing down irregularly from both ends to a few feet in the center. The thickness of the body varies greatly along the line of lode, ranging from a few feet up to 470 ft. thick. The ore horizon is not constant, but varies, following in a broad sense the topography. The body in general dips slightly to the northeast, and is broken up by numerous small faults and fractures. The ore-bearing formations, consisting of mineralized schist and mineralized granite porphyry, stand fairly well and offer no difficulty in mining operations. The bulk of the ore is chalcocite disseminated in schist. In places cupriferous pyrite is closely associated with the chalcocite. The mineralized gr'anite-porphyry forhations are contiguous to the ore-bearing schist. • Overlying the orebody is an oxidized zone of leached iron-stained schist, averaging 252 ft. in thickness, termed "capping." The Line of

Jan 1, 1916

By Arthur G. Levy, Henry M. How

The purpose of the investigation on which this paper is based is to determine whether the structural change which occurs in the slow cooling of steel below the transformation range has an important effect on its engineering properties. We recognize two distinct things which occur in steel when it is brought from above to below the transformation range, first, the transformation proper, that is, the breaking up of the austenite or solid solution of the cementite in the remainder of the iron, and the liberation of its components as undissolved cementite and as ferrite or alpha iron; and second, a structural change consisting in the gradual coalescence of the ferrite and cementite respectively into larger and larger separate masses. Let us distinguish these from each other by speaking of them as " the transformation " and " the structural change " respectively. If the cooling is at all rapid the unevenness of contraction induces severe stress; so that in a sense a slow cooling has a third influence, the prevention of such stress. This transformation from austenite to ferrite plus cementite can complete itself only below the transformation range; and, because this structural change is a change in the structural arrangement of the products of that transformation, it too can complete itself only at temperatures below that range, say below 725°; and of these temperatures it is only those between 600° and 725° that give the metal sufficient mobility to permit this structural rearrangement to progress with ally rapidity. The transformation is now known to be rapid, but the structural change is relatively slow. The transformation, the liberation of the dissolved cementite from the state of solution in the austenite to a free state, leaves the steel structurally in the

Jan 1, 1913