Search Documents

By Norman L. Newbern, Robert E. Green

An investigation of the effect of size on the deformation properties of metal single crystals made it desirable to grow from the melt cylindrical aluminum single crystals possessing exactly the same crystallographic orientation but varying in diameter. Methods for the growth of rather large (up to 3 in. diam) aluminum single crystals in molds of the desired shape are well known. However, when one applies the same techniques to the growth of smaller (less than 1/8-in. diam) specimens many additional problems arise. Two of the major problems are the construction of the molds to be used and the removal of the thin specimens from these molds without deformation after growth has been completed. Also the problem of the constraint forces exerted by the mold on the specimen is much more pronounced for the smaller specimens. The technique described herein is a zone-melting method in which no mold is used since the surface tension of the molten metal and its oxide is sufficient to retain the melt. The specimen is suspended vertically in a manner similar to that of Keck and Golay.2 However, while Keck and Golay supported the specimen from both ends, the method used here supports the specimen only at the upper end. The surface tension of the molten aluminum and aluminum oxide contains the melt and suspends a length of newly grown crystal that has already passed through the molten zone until the weight of the newly grown crystal is equal to the component of surface tension holding the specimen together in the molten region. When the weight of the newly grown crystal is equal to the component of surface tension holding the specimen together the specimen pulls in two in the molten zone. The length of crystal which can be grown before this separation occurs varies with the diameter of the specimen and the size of the molten zone. In order to prevent the specimen from pulling in two a tube of glycerine is placed beneath the furnace in such a manner that the newly grown crystal passes into the glycerine which provides sufficient buoyancy to allow aluminum single crystals in wire form to be grown to lengths determined only by the length of the tube containing the glycerine. A schematic diagram of the experimental arrangement is shown in Fig. 1. The furnace used is constructed as follows. High-resistance nichrome wire is coiled on a 3/8-in. diam fused quartz tube. The distance between the windings is much less over a length of about 3/8 in. at the center so as to develop a hot spot. This core is located in the center of a 4-in. diam steel cylinder 5 in. in height and insulated from it by Kayolite. The temperature of the furnace is controlled by means of a thermocouple located near the central hot spot and a Minneapolis-Honeywell temperature controller. Temperature ins,ide the furnace is measured with a thermocouple and a standard potentiometer in the usual manner. By the above method it is possible to grow high-purity (99.99 pct Al) aluminum single-crystal wires over a range of sizes. Crystals varying from 1/8 to 1/64-in. diam were grown by the authors. Since the tube containing the glycerine cannot contain a crystal longer than approximately 3 ft, the growth of crystals longer than this presents another problem. It was found that one could cut the newly grown crystal without deformation in the region between furnace and glycerine tube try means of a cutting torch and then by moving the glycerine tube slightly aside continue

Jan 1, 1962

By John Hillman

Reconstruction of the British mining industry began shortly after nationalization in 1947 and continued until well into the 1950s with the support of the government. This support diminished as plentiful supplies of cheap oil from the Middle East made many coal mines uneconomic. The planned rundown which followed was foreshadowed in the 1965 White Paper which outlined financial measures to speed the closure of uneconomic collieries. The decline appeared likely to continue into the 21st century as the role of coal in UK energy requirements became less and less significant. This policy was well on course in 1973 when the oil crisis led to a complete reappraisal of the position. A government examination in 1974 of the coal industry then supported the National Coal Board's general strategy of major capital investment as set out in its 'Plan for Coal'. The plan was aimed at halting the intended decline in the industry's capacity and restoring it to 120 million tons of deep mined output in 1985. The plan proposed action along the following lines: Increase output by major investment in construction at existing collieries with sufficient reserves to give 13 million tons per annum extra output.

Jan 1, 1980

By Richard P. Rothwell

THOUGH coal has been mined in this country for more than a century, no systematic effort was ever successfully made to ascertain the total amount produced. The production of the Cumberland Basin, Md., and the shipments from the anthracite fields of Pennsylvania, have been placed upon record, thanks to the intelligence sand foresight of Mr. C. Slack in the former case, and to the late Mr. B. Bannan in the latter. For some of the years between 1822 and 1842, the production of the Richmond Basin was reported by Mr. R. C. Taylor, but since that date till the author undertook this work it was impossible to obtain any statement of the production of this field. A few of the newer fields, such as that of Mt. Diablo, Cal., have been fully reported, and a few of the newer States have also had this service performed by some intelligent private individuals.; but no statistics of coal production have ever been collected either by the State or General Government, if we except the returns for the years 1869-70 of the census report. During the year 1875, by great exertions, I succeeded in obtaining, and July 3d, 1875, gave in the Engineering and Mining Journal what, "though not an accurate statement of our coal production," was " by far the most full and reliable that had ever been published." Though that report showed the production of bituminous coal to be 23,630,094 gross tons, or about six million tons more than had ever before been reported, it was in reality two and a half million tons below the actual output. The more full returns I obtained for 1875 gave many figures for 1874

Jan 1, 1877

By C. W. Hill, G. P. Luckey

In a previous article1 preliminary experiments were described, indicating the possibilities of a quantitative spectroscopic method for the determination of small amounts of lead in copper, which would be accurate and rapid, and could be carried out in the refining plant by one not skilled in chemical analysis. The present paper deals with the development of the method in the factory, giving the details of apparatus and its standardization, and presenting a comparison of the accuracy of the method with that of the standard electrolytic determination. (For variations and other applications of the method, the reader is referred to the first article.) A carefully weighed sample (0.4 gm.) of the copper to be tested is placed in a cavity in a graphite positive electrode. An arc capable of

Jan 1, 1919

By Charles W. Frey

OF all the machinery used in mining work, mine cars are probably the most abused. They are hauled through water and muck, up hill and down grade, whipped around curves, bumped and jerked, and exposed to the ravages of the weather. However, as a general rule their lubrication is not altogether neglected. The mine operator may not heed the extra drag that a frozen conveyor bearing gives, but he is all too aware of the increased load that faulty mine car wheels put on his power plant. When the circuit breakers begin to fly, and when his mine loco- motives come out with only half the cars that they were able to carry a month before, then neglected mine car wheel lubrication becomes apparent, and woe to the person responsible.

Jan 1, 1938

By C. W. Washburne

THE waters of many oil fields have been regarded as buried sea water which has been retained in the sediments since the time of their deposition. The preservation of connate water through geological time has seemed improbable to only a few geologists, but there is room for doubt that buried sea water could remain in the strata during their periods of deformation and during the many subsequent epochs of. the circulation of meteoric ground-water. Some have even suggested that the calcium chloride water in the deep mines of the Lake Superior region is ancient sea water buried in the Algonkian lavas, but it is hard to understand how such water could be derived from the highly sodic and sulphatic water of the sea. It would seem more plausible to connect the calcium chloride with the highly calcic magmas of the greenstones in which it is found. Chemical analyses of waters associated with oil differ widely from the composition of sea water, requiring extensive alteration of the latter, if the former is truly its derivative. The first notable difference is the general absence of sulphates from oil-field waters, but this has been explained satisfactorily through reduction by hydrocarbons and organic matter. Oil reduces sulphates with the production of hydrogen sulphide (or sulphur), water, and carbonates (or carbon dioxide). The second striking difference is in the high ratio of chlorine to sodium. An examination of the analyses of chloride waters from oil fields shows that they contain a large relative excess of chlorine over that in sea water. Moreover, there is difficulty in finding chemical reactions that are probable in nature, by which sea water could be converted into anything like the chloride waters of oil fields. In the latter a large part of the chlorine occurs as calcium acid magnesium chloride. This condition might be produced by the removal of sodium carbonate, which; however, cannot be precipitated in the presence of much calcium or, magnesium.

Jan 3, 1914

By Robert Schorr

A Discussion of the Paper by Robert Schorr, read at the Atlantic City meeting, February, 1904. (Washington Meeting, May, 1905.) E. T. DUMBLE, Houston, Texas (communication to the Secretary*) :-In addition to the list of publications mentioned by Mr. Schorr and those by Prof. Hofman, I call attention to the following references : Studi sulle Lignite, by Capacci. Turin (1890). (An excellent work.) Report of Brown Coal Industry in Germany. J. Cosmo Newberry. Department of Mines, Victoria (1892). Second Report of the Royal Commission. on Coal Supply. Vol. II. London (1904). Peat Fuel: Its Manufacture and Use. Report of the Bureau of Mines of Ontario, 1903. Mr. Schorr says : " Brown coal and peat are briquetted as a rule without binder," but this statement is entirely true only so far as raw peat is concerned, and it is but partly true of brown coal. With regard to raw peat, briquetting without bond is carried on successfully both in Europe and America, and the development of the industry in Canada is fully described in the Bureau of Mines report for 1903, mentioned above. While there is still room for improvement in the efficiency of some of the arrangements for drying the peat previous to briquetting, a very satisfactory fuel is made at a price which enables it to compete with coal. During the late strike in the anthracite regions of Pennsylvania, the manufacture of peat: briquettes received a considerable impetus, and possibly the attention directed to it on this account may result in a. considerable increase in the output. In Canada. the peat when it is first excavated from the ground

Mar 1, 1905

By Dart Wantland, C. A. Heiland

There once was a little kid, whose lot was a very tough one until he grew up. His parents did not have much in common; from all indications, it is probable that the child was not wanted. His father Geology and his mother Physics separated shortly after his birth, which occurred during the World War amid a smoke screen of mathematics. He was kicked around a great deal. His parents could not agree on a name, and they finally christened him "Geophysics," for short. His relatives insisted that the name should be "Geophysical Prospecting," "Geophysical Exploration" or "Exploratory Geophysics"; though the youngster has grown up by now, this battle is still going on. His father did not think the child would amount to much until he began to show some unexpected talents, which were acquired, no doubt, from his mother Physics. His progress caused his father no little worry, and he began to wonder whether his offspring would help him in his business when he grew up or would set up shop in competition with the old man. His aunt Petroleum watched his growth with benevolent interest; his uncle Mining remained rather skeptical and cousin Civil Engineering not only assumed the attitude of the man from Missouri but was not much convinced even after he had been shown. Making a long story short, the kid decided that he had to stand on his own feet and get along as best he could. Having come from a good family he possessed some outstanding characteristics such as resourcefulness and a reasonable amount of business ability. He therefore decided that it would be to his advantage to follow in his father's and mother's footsteps as much as possible, and develop the good qualities of both. As a result, the youngster did fairly well for himself, and his relatives decided that it might be to their advantage to be on better terms with him. Father Geology had come to the conclusion that the boy could be very helpful to him and now wanted him to live in his house. His mother, who had brought him through the teething and measles stages, felt quite capable of bringing up the boy without the help of his father; and, as the fairer sex will do, would confide to a neighbor every now and then that his

Jan 1, 1940

By C. A. Heiland, Dart Wantland

There once was a little kid, whose lot was a very tough one until he grew up. His parents did not have much in common; from all indications, it is probable that the child was not wanted. His father Geology and his mother Physics separated shortly after his birth, which occurred during the World War amid a smoke screen of mathematics. He was kicked around a great deal. His parents could not agree on a name, and they finally christened him "Geophysics," for short. His relatives insisted that the name should be "Geophysical Prospecting," "Geophysical Exploration" or "Exploratory Geophysics"; though the youngster has grown up by now, this battle is still going on. His father did not think the child would amount to much until he began to show some unexpected talents, which were acquired, no doubt, from his mother Physics. His progress caused his father no little worry, and he began to wonder whether his offspring would help him in his business when he grew up or would set up shop in competition with the old man. His aunt Petroleum watched his growth with benevolent interest; his uncle Mining remained rather skeptical and cousin Civil Engineering not only assumed the attitude of the man from Missouri but was not much convinced even after he had been shown. Making a long story short, the kid decided that he had to stand on his own feet and get along as best he could. Having come from a good family he possessed some outstanding characteristics such as resourcefulness and a reasonable amount of business ability. He therefore decided that it would be to his advantage to follow in his father's and mother's footsteps as much as possible, and develop the good qualities of both. As a result, the youngster did fairly well for himself, and his relatives decided that it might be to their advantage to be on better terms with him. Father Geology had come to the conclusion that the boy could be very helpful to him and now wanted him to live in his house. His mother, who had brought him through the teething and measles stages, felt quite capable of bringing up the boy without the help of his father; and, as the fairer sex will do, would confide to a neighbor every now and then that his

Jan 1, 1940

By G. R. Fritterer

Investigators in the field of temperature measurement have long sought a thermoelectric couple fulfilling the following requirements: 1. It should be useful up to and including high industrial temperatures; i. e., 1000 to 1800 C. 2. Its thermoelectric variation with temperature should be linear and be maintained after heating to high temperatures for long periods of time. 3. It should be reproducible; i. e., different couples of the same elements should have similar calibration curves. 4. Its thermoelectric power should be large so as to allow the industrial use of rugged recording instruments. 5. Chemical reactions with, and physical changes within the elements of the couple should not alter its calibration. No thermocouple proposed to date exhibits simultaneously all of these characteristics, whereas the couple about to be described fulfills all requirements to a satisfactory degree. New Thermoelectric Materials A thorough survey of the literature on thermoelectricity revealed that present-day thermocouples could not meet the specifications mentioned above because their thermoelements are metallic. Metals have a marked tendency to deteriorate chemically and their melting points limit their use to low temperatures. Refractory substances, however, are usually resistant to chemical attack and are quite stable at high temperatures. Hence a survey of refractory substances having thermoelectric possibilities was made. One class of thermocouples considered was that in which carbon and a carbide of some metal or nonmetal were the thermoelements. Previous investigators neglected to study this field but certain recommendations were made by them for the use of couples in which carbon served as one element. These proposals are listed in Table 1. The couples suggested are unsatisfactory because of their low thermoelectric powers, the low melting points of their metallic elements, etc. The

Jan 1, 1933

By Felix B. Shay

The Agua Fria mine is in eastern Honduras at Lat. 140" 06' N., Long. 86" 36' W. Danli, the seat of the local municipal government, is the nearest town. The property is approximately 44 miles east of Tegucigalpa, the terminus of a truck road from the Pacific coast. The mine lies at an altitude of 3300 ft. with surrounding elevations as high as 6000 feet. For 20 years the oxidized croppings of the Agua Fria vein had been worked intermittently when in 1927 an attempt was made to open the property. A shaft was sunk 300 ft. and considerable ore was blocked out, but before a mill could be installed financial difficulties arose and the mine reverted to the original owners. Erle Y. Halliburton, of Los Angeles, purchased the property in 1934. At that time a careful consideration of all factors involved showed that air transport was the only practical method of moving the equipment and machinery necessary to commence production. The other alternative was by muleback, which required sectionalizing all equipment to a maximum load of 200 lb., and during the rainy season this type of freighting was subject to serious delays. It was decided to purchase a trimotor Ford powered by three Pratt and Whitney Wasp B motors developing 400 hp. each. There were several reasons for the choice: (1) this type of plane was available at a reasonable price, owing to its replacement by faster models on most of the airlines in the United States; (2) the ship was capable of carrying a pay load of 3000 Ib. over the required distance; (3) since this airplane had been widely used there would be no difficulty in securing competent personnel or in purchasing spare parts. It was necessary to rebuild the plane for cargo servicc. The windows were removed and the fuselage was entirely covered. A hatch was cut in the top of the fuselage to receive heavy crane loads and pieces of freight that were too large or too long to go through the rear door. The seats were removed and the interior of the plane was lined with Duralumin sheets. A heavy-duty landing gear was installed and the floor was reinforced. The nearest site for an airport was two miles north of the mine. The necessary grading was done by a small track-type tractor with a wheeled grader, which was brought in overland. Six weeks was required for bring-

Jan 1, 1940

By Felix B. Shay

The Agua Fria mine is in eastern Honduras at Lat. 140" 06' N., Long. 86" 36' W. Danli, the seat of the local municipal government, is the nearest town. The property is approximately 44 miles east of Tegucigalpa, the terminus of a truck road from the Pacific coast. The mine lies at an altitude of 3300 ft. with surrounding elevations as high as 6000 feet. For 20 years the oxidized croppings of the Agua Fria vein had been worked intermittently when in 1927 an attempt was made to open the property. A shaft was sunk 300 ft. and considerable ore was blocked out, but before a mill could be installed financial difficulties arose and the mine reverted to the original owners. Erle Y. Halliburton, of Los Angeles, purchased the property in 1934. At that time a careful consideration of all factors involved showed that air transport was the only practical method of moving the equipment and machinery necessary to commence production. The other alternative was by muleback, which required sectionalizing all equipment to a maximum load of 200 lb., and during the rainy season this type of freighting was subject to serious delays. It was decided to purchase a trimotor Ford powered by three Pratt and Whitney Wasp B motors developing 400 hp. each. There were several reasons for the choice: (1) this type of plane was available at a reasonable price, owing to its replacement by faster models on most of the airlines in the United States; (2) the ship was capable of carrying a pay load of 3000 Ib. over the required distance; (3) since this airplane had been widely used there would be no difficulty in securing competent personnel or in purchasing spare parts. It was necessary to rebuild the plane for cargo servicc. The windows were removed and the fuselage was entirely covered. A hatch was cut in the top of the fuselage to receive heavy crane loads and pieces of freight that were too large or too long to go through the rear door. The seats were removed and the interior of the plane was lined with Duralumin sheets. A heavy-duty landing gear was installed and the floor was reinforced. The nearest site for an airport was two miles north of the mine. The necessary grading was done by a small track-type tractor with a wheeled grader, which was brought in overland. Six weeks was required for bring-

Jan 1, 1940

By D. W. Peaceman

In previous papers by this author on numerical calculations of multidimensional miscible displacement, some simplifying assumptions were made in writing the dispersion term of the differential equation. It was assumed that the flow vectors were essentially parallel to the x-axis. However, in most multidimensional miscible displacements, the flow vectors are not so simply oriented with respect to the coordinate axes. This paper derives the correct dispersion term /or the more general case; gives a difference approximation /or the dispersion tern; and derives the stability criterion for the corresponding explicit difference eguation.

Jan 1, 1967

By Nicholas J. Palethorpe

BACKGROUND Before addressing the above topic in any detail, it is pertinent to provide some background on Australia for those people who have not been there or who have a limited knowledge of our continent. Australia is approximately the size of the continental U.S.A. (excluding Alaska) covering an area of approximately 7 million square kilometres. It has a very dry climate which has led to a concentration of people in major cities scattered around the continents perimeter. Australia's population is currently approximately 15 million. Of the work force of 6.3 million, 72% work in tertiary industries, 20.2% in manufacture, 6.5% in agriculture and 1.3% in mining. Agriculture accounts for 46% of exports, mining for 31% and manufacturing for 23,. Economic activity is based on:- Agriculture This is capital intensive and covers extensive areas and is reliant on low cost farming. A.range of foods and fibres are produced with over 70% of production being exported. Such products are of course subject to the usual vagaries of world market demand and market access, particularly in regard to the operation of trade blocks such as the E.E.C. Mineral Resources A wide range of minerals and an abundance of iron ore, coal, gas and uranium resources provide an increasing volume of exports. However, Autralia's oil resources at present only supply approximately 70% of local requirements. Industry This is diverse and encompasses the processing of agricultural products and mineral ores as well as helping to supply the consumer and capital goods needs of the whole community. However, the small scale of local markets, the geographic isolation of Australia and relatively high wage costs have limited the scale of Australia's industry. Advanced technology has overcome some of these difficulties and high tariff and import quotas protect local producers from the full force of international competition. In 1980/81 Australia's Gross Domestic Product amounted to $130 billion with approximately 24% of this being devoted to investment. In the past decade Australia has experienced inflation rates ranging from 5% to 17% and only modest real growth rates ranging from 0.4% to 5% per annum. We have also experienced, as have many other industrialised nations, continuing wage and price increases. Unemployment presently stands at 6%. MINERAL DEVELOPMENT As the above figures indicate, Australia's continuing prosperity is very dependent on the mineral and agricultrual sectors of our economy. The dependence on these sectors is highlighted by the table below which indicates our position in a global context. [Australian Production of Minerals in a World Context Western World % Total Western World Position Mineral Production 1980 1st Rutile 75 Ilmenite 31 Zircon 70 Bauxite 36 Iron Ore 11 Tungsten 14 2nd Lead (Conc.) 15 3rd Manganese Ore 14 Brown Coal 11 (1979) Zinc (Conc.) 10 4thSilver (Conc.) 10 Nickel 6 5th Tin (Conc.) 5 6th Black Coal 5 Gold 2 Source: Mining Annual Review 1981] The total value of all mineral and fuel exports in 1980/81 is estimated at $5.9 billion. This prominence in the world mineral production has largely been achieved in the last 15 - 20 years. In fact, in the early 1960's, Australia had only 2 major mining export centres, Broken Hill in New South Wales and Mt. Isa in Queensland. This growth is highlighted by the fact that in 1963, for example, we exported only 9 tonnes of iron ore and less than 4 million tonnes of coal. In 1980/81 we exported 75m. tonnes ',of iron ore (valued at $1,117m.) and 47m. tonnes of coal valued at $1,965m.). The growth in our mineral industry has come about because of a number of factors. Abundance of Mineral Resources We are particularly well endowed with mineral resources, as indicated below.

Jan 1, 1982

By F. E. Crane, H. A. Kendall, G. H. F. Gardner

Two effects of a difference in density may be observed in miscible displacement. As the difference is increased from zero there is first a change in mode from multiple fingers to a single finger. A further increase results in a more rapid growth of the single finger. Miscible displacement with multiple fingers has been discussed by Blackwell, et al, whereas miscible displacement with a single finger has been discussed by Craig, et al. In the present paper experiments are described which bridge the gap between these extreme cases. INTRODUCTION Craig, et al,1 investigated the effect of gravity on frontal displacements for circumstances in which the gravity forces were significant. Blackwell, et a1,2 dealt with the other extreme in which gravity forces were negligible. The considerable difference between their results is illustrated in Fig. 1 where the breakthrough recoveries are plotted against the mobility ratio. The experiments described in the present paper were conducted to examine how the transition from the one extreme case to the other occurs when the gravity forces are gradually reduced. The transition is well illustrated by the production history after breakthrough. Fig. 2 shows how the number of pore volumes which must be injected at a constant rate to displace 98 per cent of the original fluid depends on the gravity force. For each mobility ratio there is a transition range, and a very significant change in the number of pore volumes occurs when this range is traversed. This range of the gravity force is physically linked with the formation of viscous fingers. A single finger is predominant for larger gravity forces; a multiplicity of fingers is formed for smaller gravity forces. Improved recovery and the occurrence of multiple fingers is concomitant with a large increase in the amount by which the fluids are mixed within the porous medium. The transition range depends on all the dimension-less groups which characterize the problem; but this dependence has not been exhaustively studied as yet and only fragmentary results are discussed in this paper.

By C. W. Wark, Fred Wise

The Getchell mine, a comparatively recent gold discovery, is in the old Potosi mining district, Humboldt County, Nevada. All ore is mined from open pits using Diesel shovels and gasoline trucks. Two types of ore are mined, oxide and sulphide. Oxide ores are siliceous or shaly; sulphide ores either gougy, siliceous or shaly. In mining, the sulphide ore is segregated into hard and gougy ore, because the gouge must be dried before it can be crushed. The oxide ore is not segregated. General Metallurgy The oxide ore is the leached outcrop that overlies the sulphide ore body. All of the iron and arsenic sulphides found in the sulphide ores have been thoroughly oxidized. The sulphur and arsenic have been leached out while the iron is present as hematite and limonite. The oxide ore is amenable to direct cyanidation, and although no visible free gold is present it is released at a comparatively coarse grind. The sulphide ore is more refractory, since the gold is all of micron size and some of it is locked in fine sulphides. It has been established microscopically that the free gold is coated with an impervious shell, which is probably some form of iron compound. The sulphide ores contain from 1.5 to 2 per cent of arsenic, which is present as orpiment and realgar with minor amounts of arsenopyrite. The orpiment and realgar are of a later mineralization than the gold and are barren. Roasting and washing of the sulphide ore prior to cyanidation is necessary to eliminate , the arsenic, to alter the gold coating from an insoluble form to a soluble form, and to release the gold associated with the fine sulphides. Washing the ground calcine in weak sulphuric acid, trona, or hot water are beneficial in the order named, but to date the water is the best from an economic standpoint. Metallurgical tests as well as plant practice indicate that a certain amount of gold cannot be recovered even by going beyond economic practices. On this basis metallurgical results are viewed in the light of an optimum tailing rather than a percentage of extraction. Milling Practice Crushing (Fig. I).—There are three primary ore bins, one each for oxide ore, gougy sulphide ore, and hard sulphide ore. In front of each bin a substantial yard is maintained, which makes it possible to Stockpile 2500 tons of oxidized ore, 1000 tons of hard sulphide ore, and 1000 tons of gougy sulphide ore. The bins are fed by a 60-hp. caterpillar bulldozer from the stockpiles. Fig. I shows the method and

Jan 1, 1943

By Fred Wise, C. W. Wark

The Getchell mine, a comparatively recent gold discovery, is in the old Potosi mining district, Humboldt County, Nevada. All ore is mined from open pits using Diesel shovels and gasoline trucks. Two types of ore are mined, oxide and sulphide. Oxide ores are siliceous or shaly; sulphide ores either gougy, siliceous or shaly. In mining, the sulphide ore is segregated into hard and gougy ore, because the gouge must be dried before it can be crushed. The oxide ore is not segregated. General Metallurgy The oxide ore is the leached outcrop that overlies the sulphide ore body. All of the iron and arsenic sulphides found in the sulphide ores have been thoroughly oxidized. The sulphur and arsenic have been leached out while the iron is present as hematite and limonite. The oxide ore is amenable to direct cyanidation, and although no visible free gold is present it is released at a comparatively coarse grind. The sulphide ore is more refractory, since the gold is all of micron size and some of it is locked in fine sulphides. It has been established microscopically that the free gold is coated with an impervious shell, which is probably some form of iron compound. The sulphide ores contain from 1.5 to 2 per cent of arsenic, which is present as orpiment and realgar with minor amounts of arsenopyrite. The orpiment and realgar are of a later mineralization than the gold and are barren. Roasting and washing of the sulphide ore prior to cyanidation is necessary to eliminate , the arsenic, to alter the gold coating from an insoluble form to a soluble form, and to release the gold associated with the fine sulphides. Washing the ground calcine in weak sulphuric acid, trona, or hot water are beneficial in the order named, but to date the water is the best from an economic standpoint. Metallurgical tests as well as plant practice indicate that a certain amount of gold cannot be recovered even by going beyond economic practices. On this basis metallurgical results are viewed in the light of an optimum tailing rather than a percentage of extraction. Milling Practice Crushing (Fig. I).—There are three primary ore bins, one each for oxide ore, gougy sulphide ore, and hard sulphide ore. In front of each bin a substantial yard is maintained, which makes it possible to Stockpile 2500 tons of oxidized ore, 1000 tons of hard sulphide ore, and 1000 tons of gougy sulphide ore. The bins are fed by a 60-hp. caterpillar bulldozer from the stockpiles. Fig. I shows the method and

Jan 1, 1943

By M. Lastra, A. Cruz, J. Menacho

The technical feasibility of treating exotic copper ore with an acid cure using concentrated H2S04 is studied. Applications in a conventional percolation leaching circuit for unaltered ore and in a conventional agitation leaching circuit for altered ore are examined. The main effects of an acid cure are to inhibit silica dissolution and to increase the sedimentation rate of agitated pulps. An increase in the rate and degree of copper extraction is also observed. Based on these results and the minimal additional investment required, acid curing appears to provide an excellent approach for treating exotic copper ores.

Jan 1, 1980

By D. Turnbull, R. E. Cech

Small particles, 10-20 microns diameter, of a 28.6 atom pct nickel, balance iron alloy, have been supercooled 186 C with respect to bulk alloy M, temperature. Particles exhibit a marked mechanical shock sensitivity while being held in a supercooled state. The tendency for shock to induce martensitic transformation appears to be a maximum at —140 to —160°. Slow cooling of particles in mechanical contact with one another results in extensive martensite formation. This is prob-ably the same effect as the catalytic effect observed in polycrystals where martensite formation in one grain induces transformation in other grains. AS a result of extensive research over the past decade on the martensitic transformation, a much better though not complete understanding of the transformation has resulted. Recent reviews by Bilby and Christian' and Kaufman and Cohen2 have

Jan 1, 1959

By I. Havenaar

EXPERIMENTAL DATA In an article by C. K. Ferguson and J. A. Klotz,1 experiments on the filtration of drilling muds under borehole conditions are discussed. Experimental data on mud filtration through the wall and the bottom of the hole are presented. From the data on bottom-hole filtration it was concluded that the filtrate does not flow freely into the formation, but that the pores of the formation are plugged by the mud. A quantitative interpretation of the data can be civen, by using a formula for bottom-hole filtration, dehved below. This formula is based on the following assumptions, 1. Each time a blade of a drag bit, or a cone of a roller bit, moves along the bottom of the hole, the mud cake is completely removed. 3. A new mud cake is immediately formed on the freshly produced surface, and losses of "whole" mud into the formation are negligible (this is equivalent to an immediate plugging of the pores). 3. The filtration of the mud on the bottom of the hole follows the classic law: V = A +1—(Eq. I), where t is the time required to yield a volume of filtrate V, A is the surface area of filter cake, and C is a constant. The application of this equation means that any eroding effect of the mud stream on the mud cake is neglected. The formula for the calculation of the volume of filtrate, Q,, flowing in one second through the hole bottom (diam. d cm), when using a bit with n cones or blades rotating at a rate of rn revolutions per second, is derived as follows: The mud cake is formed on the bottom of the hole in the time t =1; the filtrate volume V which passes n through the bottom In this time 1s given by Eq. 1: After1/nmsec the mud cake is removed. In one m second this process takes place nm times. Therefore the volume of filtrate, obtained in one second is given by This equation has now been applied to the experiments of Ferguson and Klotz. The constants C were derived by means of Eq. 1 from the API filter losses of the muds used by the authors (t = 1,800 sec; A = 45.16cm2). A three-cone bit was used (n = 3) at 90 rpm (m = 1.5). The calculated figures are compared with the experimental data in the table below. The calculated values of Q, are usually lower than the experimental values. This may be due to the following causes. 1. The value of C used in the calculation is based on the API filter test (filtration pressure of 100 psi), whereas the experimental data were obtained with a filtration pressure of 200 psi. Although the effect of the pressure on C is not large, C decreases somewhat with increasing pressure, and this leads to a higher filtration rate. 2. Mud losses and the eroding action of the mud stream on the cake are not entirely negligible. 3. The values of Q, derived by Ferguson and Klotz from their experiments are too high, because of their assumption that all pore liquid within the formation drilled is picked up by the drilling mud. It is found, however, that the calculated values of Qf, except in the case of oil base muds, are of the right order of magnitude. ACKNOWLEDGMENT The author wishes to thank the management of the Koninklijke/Shell-Laboratorium, Amsterdam, for permission to publish this note.

Jan 1, 1957