Search Documents

By Paul R. La Pointe

GEOTECHNICAL OBJECTIVES OF UCG PROGRAM Underground coal gasification (UCG) is one of several in situ extraction technologies for utilizing deep, otherwise unmineable coal. This technology involves the injection of air or oxygen into the target coal seam, ignition of the coal and recovery of product gases. Geotechnical characteristics of the coal and enclosing rock strata strongly influence the success of this Process. The flame front follows the coal cleats (Hill, 1979), and cleating and bedding control the manner in which coal collapses into the cavity, thereby affecting recovery efficiency (Ramirez and others, 1982). Moreover, coal seams typically behave as fracture dominated aquifers in which cleat orientations govern subsequent contaminant dispersal. For these reasons, the Anaconda Minerals Co. undertook a detailed study of fracturing within the Wyodak-Anderson Coal in the eastern Powder River Basin (PRB) near its Rocky Hill UCG test site (Fig. 1). STRESS HISTORY AND FRACTURING IN THE POWDER RIVER BASIN Vertical jointing, or cleating, in coals may arise from shrinkage shortly after deposition under low confining pressures, or later in time, soon after burial but after the coalification process is well advanced (Ting, 1977). There is much evidence to support the formation of cleating after coalification (e.g. Hawkes and Mellor, 1970; McCulloch and others, 1974), which suggests that the stress state existing at that time strongly influences cleat formation. McCulloch and others (1974) argue that the typically better developed face cleat forms parallel to the plane containing [ol] and [o2]. Where the relation between cleats and stess has been studied (McCulloch and others, 1974; Stone and Snoeberger, 1977; Ward, 1977; Kulander and Dean, 1978), the highly systematic face cleat strongly parallels the [o1] direction. Stone and Snoeberger (1977) report face and butt cleat measurements of N70E and N29W for the Felix Coals 220 m stratigraphically above the Wyodak at the Hoe Creek UCG site (Fig. 1). Structural trends also indicate the past state of stress in the PRB. Glaze and Keller (1963) suggest that the NE-SW regional compression during the late Permian formed major N-S fold lines and basement magnetic anomalies. Mapel (1959) describes folds having N60W and N30W rends in the northern PRB, as well as a large normal fault trending northeast. Glass (1976) also describes normal faults trending northeast. Similarly, Olive (1957) mapped normal faults

Jan 1, 1984

By V. N. Mackiw

IN the process employed by Sherritt Gordon Mines Ltd. for the production of metallic nickel, a sul-fide concentrate is leached with ammonia and air under pressure. Following the removal of iron, copper, and other impurities, there remains a purified solution having the following analysis: 40 to 50 g per liter Ni, 200 to 400 g per liter (NH4)2 SO 4, and 20 to 30 g per liter NH3. Metallic nickel is reduced from this solution by hydrogen under pressure at 300' to 350°F in mechanically agitated autoclaves. A catalyst, ferrous sulfate, is required to initiate the first reduction. After the reduction, the depleted solution is discharged, leaving the metallic nickel in the autoclave. The nickel produced, being in a finely divided form, is used as a catalyst for the reduction of the next batch of solution. Upon repeated use the metallic nickel particles increase in size and become more compact, resulting in the production of a powder with higher apparent density. For this reason, each reduction is termed densification. Finally, when the burden of metal powder in the autoclave becomes too great to obtain effective agitation, both powder and depleted solution are discharged. The autoclave is then filled with fresh solution, ferrous sulfate catalyst added as before, and a new cycle started. The operation is described in earlier publications.1-6 A comprehensive historical review of the reduction of metals from solutions in general was given in a paper by Schaufelberger.7 The experimental data presented in this paper were taken from the work done in the Research Laboratory of Sherritt Gordon Mines Ltd. in Ottawa during the development of the process in 1951 and 1952. The results of the work were tested on a pilot plant scale in Ottawa in the period 1952 to 1953. Following laboratory and the pilot plant studies a commercial process has operated successfully since 1954 in the Nickel Refinery of Sherritt Gordon Mines Ltd. in Fort Saskatchewan, Alberta. General Experimental Technique The experiments were carried out in a stainless steel, 1-gallon, agitated autoclave designed and manufactured by Autoclave Engineers Inc. The inside dimensions of the vessel were 5 in. diam and 12 in. depth. The stirrer consisted of a 1/2 in. diam shaft 11 in. long fitted, with an axial flow type impeller (three blades bent to throw downwards) and a radial flow

Jan 1, 1958

By Robert Maddin

THE application of electrolytic polishing of metals introduced a new technique for preparing surfaces, especially for single crystals. This procedure has generally been assumed to eliminate the strain introduced by mechanical polishing and to result in a more truly representative surface, particularly in the case of soft metallic materials. However, apparently little information is available concerning specific characteristics of a surface prepared electrolytically. The conventional method of mechanical polishing is known to produce a layer of distorted metal which is usually removed by a suitable chemical etchant. To what depth the strain introduced by mechanical polishing penetrates into the lattice is still obscure. The present investigation illustrates the apparently anomalous appearances of glide ellipses on electrolytically polished surfaces of aluminum single crystals. EXPERIMENTAL PROCEDURE AND RESULTS Aluminum single crystals, 99.975 pct pure, remaining from the investigation of Found,1 were polished electrolytically using a solution of fluoboric acid and a low current density. Laue back-reflection technique, interpreted after the manner of Greninger,2 was used to determine the orientation and the specimen axis rotation of the crystals. Three flat surfaces about 4 mm wide parallel to the specimen axis, one perpendicular to the theoretical slip direction and the other two 1200 apart, were polished mechanically and repolished electrolytically. A tensile load was applied using a Southwark-Emery tensile machine at a rate of about 40 lb per min. Elongation was measured by noting the initial and final gauge lengths. X ray diffraction was used to obtain the usual X and X values in order to calculate the elongation and shear by plotting stereographically the specimen axis rotation by means of the Schmid-Boas formula.3 In Table I may be found the value of the gauge diameter, measured elongation, calculated elongation and shear for the crystals investigated. Fig 1 shows the initial and final positions of the specimen axes of the crystals. [ ] At a low magnification the slip lines developed on specimen Al-I appeared straight and rather evenly spaced. However, at a high magnification, the slip lines were seen to be composed of small markings which were present throughout the length of the specimen (Fig 2). The distance between the markings was fairly constant and their directions all parallel to one another. Fig 3-5, photographed on different surfaces of the specimen, illustrate the interesting appearance of these lines. It may be noticed from Fig 4 that the markings, which present the appearance of

Jan 1, 1948

By Arthur F. Taggart

The quality of aggregate materials is. of major importance in governing durability and permanence of concrete structures. The problem of selecting suitable aggregate materials is two-fold. Geological factors include the type and character of the aggregate source, presence of known or suspected reactive constituents, and presence of thermally incompatible materials. Laboratory investigations include petrographic studies, soundness and reactivity tests, and tests of thermal properties. The importance of each factor in the selection of satisfactory aggregate material is considered in detail.

Jan 1, 1950

By Robert Maddin

The application of electrolytic polishing of metals introduced a new technique for preparing surfaces, especially for single crystals. This procedure generallv has been assumed to eliminate the strain introduced by mechanical polishing and to result in a more truly representative surface, particularly in the case of soft metallic materials. However, apparently little information is available concerning specific characteristics of a surface prepared electrolytically. The conventional method of mechanical polishing is known to produce a layer of distorted metal which is usually removed by a suitable chemical etchant. To what depth the strain introduced by mechanical polishing penetrates into the lattice is still obscure. The present investigation illustrates the apparently anomalous appearances of glide ellipses on electrolytically polished surfaces of aluminum single crystals. Experimental Procedure and Results Aluminum single crystals, 99.975 pct pure, remaining from the investigation of Found,' were polished electrolytically using a solution of fluoboric acid and a low current density. Laue back-reflection technique, interpreted after the manner of Greninger,2 was used to determine the orientation and the specimen axis rotation of the crystals. Three flat surfaces about 4 mm wide parallel to the specimen axis, one perpendicular to the theoretical slip direction and the other two 120° apart, were polished mechanically and repolished electrolytically. A tensile load was applied using a Southwark-Emery tensile machine at a rate of about 40 lb per min. Elongation was measured by noting the initial and final gauge lengths. X ray diffraction was used to obtain the usual x and X values in order to calculate the elongation and shear by plotting stereographically the specimen axis rotation by means of the Schmid-Boas formula.³ In Table I may be found the value of the gauge diameter, measured elongation, calculated elongation and shear for the crystals investigated. Fig I shows the initial and final positions of the specimen axes of the crystals. At a low magnification the slip lines developed on specimen Al-I appeared straight and rather evenly spaced. However, at a high magnification, the slip lines were seen to be composed of small markings which were present throughout the length of the specimen (Fig 2). The distance between the markings was fairly constant and their directions all parallel to One another' Fig 3-57 photographed On different surfaces of the specimen, illustrate the interesting appearance of these lines. It may be noticed from Fig 4 that the markings, which present the appearance of

Jan 1, 1949

By Charles Behre

THIS paper deals with recent geologic studies in the slate belt of Northampton, Lehigh and Berks counties, Pennsylvania. The work was conducted under the auspices of the Pennsylvania Topographic and Geologic Survey. Three years have now been spent in detailed consideration of the economic geology of this region. In the field, particular attention was paid to the bearing of geology on quarry development and property valuation and the object of this paper is to summarize the results from that viewpoint. Excellent studies of a somewhat similar nature have already been carried out by Bowles,1 but with the emphasis upon the details of quarrying and fabricating methods, rather than upon the geologic relations. THE NORTHAMPTON-LEHIGH-BERKS DISTRICT Location The region here discussed lies in east-central Pennsylvania and extends southwestward from Delaware River, on the New Jersey line, to the Schuylkill in north-central Berks County. It is an elongated belt occupying the northern sections of the three counties mentioned and lying along the southern edge of Blue Mountain. Its length is about 50 miles and its average width five or six, though in places it attains a maximum of 10 miles.

Jan 1, 1928

By E. L. BROKENSHIRE

FLUORSPAR, a little known non-metallic mineral, referred to technically as fluorite, chemically as calcium fluoride, is a compound of calcium and fluorine in the ratio of one molecule of calcium to two of fluorine. By weight it is composed of 51.3 per cent of calcium and 48.7 per cent of fluorine. Its specific gravity is 3.2. It is brittle, has a hardness of four and can be easily scratched with a knife. It weighs about 200 Ib. per cubic foot and has a melting point of 1650" F. The color of fluorspar ranges from pure white and opaque white, according to its purity, to various hues of yellow, green, pink, lavender, blue and brown, to bluish black. Although the lumps have color, when ground the fluorspar becomes pure white. The reason for this is because the mineral usually carries no fixed pigment, the color being produced by the re- fraction of light rays within the crystal structure and small quantities of organic matter which readily oxidizes. It crystallizes in the isometric system with perfect octahedral cleavages.

Jan 1, 1929

By Charles Y. Clayton

THE general public does not know that there is such a thing as metallurgy and it is very seldom that you see the word metallurgy in print except in technical magazines. Perhaps it is more to the front now than in former years; the Dee. 30, 1929, issue of Time mentioned under the heading of "Science7' certain new achievements in metallurgy, which may be cited as a rare instance of the use of the word in anything but the technical press. Too often the part the metallurgist plays in the advancement of the different branches of engineering is overlooked. To say that the public does not know there is such a profession as metallurgical engineering seems to be a bold statement, but had there beep time a questionnaire could have proved this beyond doubt. Suppose a carefully-planned questionnaire had been sent to all high school students asking them, among other questions, to list the different branches of engineering, I believe that the several professions would have been listed in this manner: (1) Electrical engineering; (2) mechanical; (3) civil, and (4)' mining. One in each hundred might have listed metallurgy as an engineering profession. Even the Society for the Promotion of Engineering Education in its Bulletin No. 10-"Investigation of Engineering Education" lists Civil, Mining, Mechanical, Electrical, and Chemical, leaving out Metallurgical Engineering.

Jan 1, 1930

By John Henry Harden

WITH imperfect instruments it is impossible to make accurate surveys; the results are inaccurate maps, with their attendant consequences. The design of the writer is to describe an improved form of tripod head, and certain defects in an English transit and a miners' dial, with the method taken to remedy the defects of the transit. When the present transit superseded the surveyor's compass, there was one special objection brought against it, and with some show of reason ; namely, that the tripod of the compass with its ball and socket motion, allowed a quicker levelling-up (and, consequently, more work) than was possible with the transit. To this objection it was replied, that the ball and socket would not allow the instrument to be levelled with the same degree of precision that could be attained with the levelling screws, and that if time was sacrificed greater accuracy was attained. Nevertheless, it is a well-known fact that in this country, and especially in England, the compass or miners' dial holds its ground solely from its rapid adjustment. Ever since the introduction of the transit, efforts have been made to give to this instrument the same facility of levelling possessed by the compass or dial, and the same means have been tried, i. e., a . ball and socket motion, since a modification of this in some form was the only method that would answer. The upper part of a transit is, however, much heavier than the corresponding parts of a compass, and, therefore, requires more binding power, which cannot be ob¬tained with an ordinary ball and socket joint. It has been a study with instrument-makers to combine the facility of these two tripods -the quickness of the ball and socket with the steadiness and accuracy of the screws; but in all attempts in this direction the ball and socket of the compass has been literally followed, the entire stability of the instrument depending upon the friction of the ball in its socket. There is great need for a tripod that can be more easily manipulated than the present form, for it rarely happens that an engineer has a level surface on which to set his instrument, and very often

Jan 1, 1879

By T. C. King

AT the new Graham-Central Mill of Eagle-Picher, near Galena, Ill., material is simultaneously dewatered and introduced into the ball-mill scoop boxes by the use of variable-speed, 24-in. spiral classifiers. This arrangement has proved satisfactory in that the moisture content of the wet feed is reduced, thus allowing maintenance of density within the mills, and a constant feed at any desired rate to the mills is provided. In this mill the primary feed is wet crushed to minus 1/2 in. and preconcentrated by jigs to produce a bulk lead-zinc-iron concentrate and a waste tailing. The jig concentrate is then dewatered by a conventional dewatering classifier and stored in bins ahead of the ball mills. Even though this material is well dewatered, the discharge at the bin bottom is sloppy because of the gradual drainage of the water from the surface of the particles. Conventional belt feeders with vertical cutoff gates are unsatisfactory because of the flushing characteristic of the wet sand. The new installation employs 24 in. x 10 ft, 9-in. Simplex double-pitch spiral classifiers for feeders from the bin bottoms to the ball mill scoop boxes (fig. 1). These units are arranged with straight tanks and are driven by 5 hp motors through a U. S. Vari-Drive to provide a 4 to 1 speed ratio. Each bin discharges through a chute into the rising side of the spiral. The flushing characteristic of the material from the bottom of the bin is utilized to maintain a steady feed. A small amount of water tapped into the bottom of the bin insures uniform feed to the classifier. Excess clear water drains over the weirs. Feed rate to the mills is controlled by the variable-speed drives. The feed delivered by the spiral at a given speed setting is relatively dry, uniform, and steady, and as such is easily controlled by the operator. The classifiers are set on a pitch of 5 in. per ft and have a sand-raking capacity of from 8 to 32 tons per hr. It is believed that the solution of this problem offers possibilities for the storage of deslimed rod-mill sands and other similar products of the industry.

Jan 1, 1951

By A. W. Faheneald, Lewis S. Prater

By taking advantage of the fundamental difference between screening and classification—namely, that specific gravity has no effect on screening but is one of the important factors in classification—a combination of the two may be used as a process of mineral concentration. Although this fact is not new, so far as is known it has had little or no commercial application. The scheme is not presented now as a process for producing finished products but rather as a preliminary operation rejecting part of the barren material from an ore before it is subjected to more costly treatment. That is largely the function of the new heavy-media concentration processes that have been widely accepted. Original installation costs for the present sink-float processes are relatively high, however, which confines their use to operations where large tonnages are handled. Sink-float has been successful on only the relatively coarse (approximately plus 10-mesh) portion of an ore, and it is in this same range that classification screening can function most satisfactorily. Theoretically, there is no upper limit to the size of particles that can be handled in a sink-float operation, but the degree of liberation in the very large pieces usually limits this. With classification screening, particles from % to % in. would be the largest that could be handled, but the lower range could be extended somewhat below 10 mesh. In order to take full advantage of the difference in specific gravities of the minerals being separated, sorting in the classifier should be under as extreme hindered-settling conditions as possible. Laboratory tests have been made on a galena ore and on an artificial mixture of quartz and magnesite to determine the separations that may be expected. Although more than one scheme may be followed, in these tests the separations were made by cutting the underflow from the classifier as a concentrate and then screening the overflow. The screen oversize was rejected as a tailing. Classification was done in a hindered-settling teeter column and screening was done by hand, using the standard 4 2 series. The accompanying flowsheet gives the testing procedure followed.

Jan 1, 1947

By A. W. Faheneald, Lewis S. Prater

By taking advantage of the fundamental difference between screening and classification—namely, that specific gravity has no effect on screening but is one of the important factors in classification—a combination of the two may be used as a process of mineral concentration. Although this fact is not new, so far as is known it has had little or no commercial application. The scheme is not presented now as a process for producing finished products but rather as a preliminary operation rejecting part of the barren material from an ore before it is subjected to more costly treatment. That is largely the function of the new heavy-media concentration processes that have been widely accepted. Original installation costs for the present sink-float processes are relatively high, however, which confines their use to operations where large tonnages are handled. Sink-float has been successful on only the relatively coarse (approximately plus 10-mesh) portion of an ore, and it is in this same range that classification screening can function most satisfactorily. Theoretically, there is no upper limit to the size of particles that can be handled in a sink-float operation, but the degree of liberation in the very large pieces usually limits this. With classification screening, particles from % to % in. would be the largest that could be handled, but the lower range could be extended somewhat below 10 mesh. In order to take full advantage of the difference in specific gravities of the minerals being separated, sorting in the classifier should be under as extreme hindered-settling conditions as possible. Laboratory tests have been made on a galena ore and on an artificial mixture of quartz and magnesite to determine the separations that may be expected. Although more than one scheme may be followed, in these tests the separations were made by cutting the underflow from the classifier as a concentrate and then screening the overflow. The screen oversize was rejected as a tailing. Classification was done in a hindered-settling teeter column and screening was done by hand, using the standard 4 2 series. The accompanying flowsheet gives the testing procedure followed.

Jan 1, 1947

By T. C. King

AT the new Graham-Central Mill of Eagle-Picher, near Galena, Ill., material is simultaneously dewatered and introduced into the ball-mill scoop boxes by the use of variable-speed, 24-in. spiral classifiers. This arrangement has proved satisfactory in that the moisture content of the wet feed is reduced, thus allowing maintenance of density within the mills, and a constant feed at any desired rate to the mills is provided. In this mill the primary feed is wet crushed to minus 1/2 in. and preconcentrated by jigs to produce a bulk lead-zinc-iron concentrate and a waste tailing. The jig concentrate is then dewatered by a conventional dewatering classifier and stored in bins ahead of the ball mills. Even though this material is well dewatered, the discharge at the bin bottom is sloppy because of the gradual drainage of the water from the surface of the particles. Conventional belt feeders with vertical cutoff gates are unsatisfactory because of the flushing characteristic of the wet sand. The new installation employs 24 in. x 10 ft, 9-in. Simplex double-pitch spiral classifiers for feeders from the bin bottoms to the ball mill scoop boxes (fig. 1). These units are arranged with straight tanks and are driven by 5 hp motors through a U. S. Vari-Drive to provide a 4 to 1 speed ratio. Each bin discharges through a chute into the rising side of the spiral. The flushing characteristic of the material from the bottom of the bin is utilized to maintain a steady feed. A small amount of water tapped into the bottom of the bin insures uniform feed to the classifier. Excess clear water drains over the weirs. Feed rate to the mills is controlled by the variable-speed drives. The feed delivered by the spiral at a given speed setting is relatively dry, uniform, and steady, and as such is easily controlled by the operator. The classifiers are set on a pitch of 5 in. per ft and have a sand-raking capacity of from 8 to 32 tons per hr. It is believed that the solution of this problem offers possibilities for the storage of deslimed rod-mill sands and other similar products of the industry.

Jan 1, 1951

By A. B. Young

THERE were produced in this country in 1923 probably in the neighborhood of 12,000 or 13,000 tons of refined and crude arsenic, by far the greater portion coming as a by product of smelting operations. Early this year copper smelters were producing arsenic at the rate of about 425 tons per month and lead smelters at the rate of 7;0 tons per month. During the entire eighteen years prior to 1919, there were produced in the United States only 47,000 tons of arsenic, which amounts to only 25 per cent. of the present output. The great increased demand has come about through the augmented use of arsenates as insecticides and arsenates as weed killers. In an extract from "Mineral Resources of the United States" on "Arsenic in 1922," Messrs. Heikes and Loughlin say, "The minimum possible demand for arsenic in 1923 was estimated at the end of 1922 to be about 13,000 tons, including 2000 tons for plate glass manufacturers, 3000 tons for lead arsenate, 3500 tons for calcium arsenate, 1500 tons for weed killers, 1200 tons for Paris green, 1000 tons for sheep dips and 750 tons for proprietary mixtures. More recent information, however, indicates twice as great a demand for calcium arsenate." The latter has found great use in the last three or four years as a weapon to combat the boll weevil pest of the southern cotton belt. ~t the present writing refined white arsenic is being quoted on the New York market at from 13)d c. to 1455 c. per Ib., while the average price during the eighteen-year period just mentioned was 4.8 c.

Jan 1, 1924

By ALEXANDER S. CORSUN

THE main orebody in the Hecla mine, Burke, Ida- ho, occurs along a nearly vertical shear zone in the Burke quartzite, with a substantial gouge and lamprophyre dike occurring in an irregular manner throughout the lode. The veins range from 3 to 40 ft. wide and dip from 70 deg. to 90 deg. There is 110 definite line of demarcation between the lode and the wall rock. Stringers of ore are often found in the wall rock for irregular distances. Horizontal but irregular quartz stringers are also found running into the walls and positions of the wall have a tendency to break to the quartz stringers and the accompanying gouge, which causes indefinite, uneven and extremely heavy side and top pressures.

Jan 1, 1930

By R. P. Smith

The diffusivity of carbon in iron, cobalt, and alloys of 89.7 and 79.3 wt pct Co has been determined by a decarburization method for the temperature range 850° to 1100°C. The Plots of log D us 1/T for the two Fe-Co alloys are linear through the region of the Curie temperature, showing that, unlike some cases of substitutional diffusion, carbon diffusion in these alloys is not affected by electron spin order. RECENT investigations1-' have shown that for substitutional diffusion in iron the change in diffusivity with temperature does not follow an Arrhenius equation, at temperatures near the Curie temperature. Data on the diffusivity of carbon in a iron5"9 indicate that this anomaly does not exist for interstitial diffusion; however, this has not been definitely established. Since cobalt and Fe-Co alloys, 80 to 100 pct Co, have Curie temperatures in a temperature range convenient for carbon-diffusion measurements they are suitable systems for studying the relation of interstitial diffusion and the Curie temperature. EXPERIMENTAL The carbon diffusivity, D, was determined by a decarburization method. The diffusion cylinders, made from small vacuum melts of electrolytic cobalt and plastiron, were about 0.76 cm diam and 6.3 cm long. A small amount of carbon was added to each melt to keep the oxygen content as low as possible. The cylinders were first treated with a hydrogen-3 pct water vapor mixture at 1100°C to constant weight, then carburized to the desired initial carbon content with a suitable CO-C02 gas mix-

Jan 1, 1964

By A. C. Fraker, H. H. Stadelmaier

WIENER and Bergerl reported the existence of the nitrides Fe3NiN and Fe3PtNwith a cubic L1'2 structure. The present note shows that a similar nitride Fe3PdN can be observed and that the composition range between the iron nitride Fe4N and the nitrides Fe3NiN, Fe3PdN, and Fe3PtN is occupied by single-phase cubic nitrides with structures intermediate between L1' and L1'2. The materials used in this investigation were electrolytic iron of 99.9 pct purity, carbonyl nickel of 99.7 pct purity, sponge platinum of 99.95 pct purity, and palladium sheet of 99.8 pct. purity. Binary alloys of the transition metals were induction-melted in a crucible of fused alumina, powdered, and screened to a particle size of - 200 mesh. The powders were nitrided at 600°C in a gas mixture of ammonia and hydrogen, and the crystal structure was determined with the aid of a Wilson powder camera. The results are compiled in Table I together with information from the paper of Wiener and Berger.1 The compound at the nominal composition Fe3PdN has a diffraction pattern with prominent reflections of a face-centered cubic lattice (h2 + k2+l2 = 3, 4, 8, 11, 12, 16) and weaker superstructure lines (h2 + k2 + 12 = 1, 2, 5, 6, 9, 10, 13, 14). With decreasing palladium content the superstructure lines become weaker and approach the intensity of those of Fe4N. No analysis was made of the intensities, but it can be assumed that the structure is that found by Wiener and Bergerl in Fe3NiN and Fe3PtN, namely L1'2 (perovskite structure) with both palladium and the interstitial nitrogen fully ordered. The dependence of the lattice constant upon the solute atom (Ni, Pd, Pt) content can be explained tolerably well by simple lattice expansion due to subsequent work confirms this suggestion, it will be of significance to order-disorder theory. The author is grateful to Lester Guttman for discussions on this topic.

Jan 1, 1961

By M. J. Sinnot, J. C. Shyne

Low-frequency mechanical damping measurements were made to investigate internal friction in Fe-A1 alloys. The atomic ordering of the Fe-A1 system strongly influenced the stress-induced ordering internal friction. Magnetoelastic damping was also encounteyed and was shown to be reduced by the application of a static stress. THIS paper describes some damping experiments made on alloys of Fe and Al. Stress-induced ordering internal friction was measured with samples containing from 9.8 to 31.3 at. pct Al. Aluminum is soluble in a-Fe to about 50 at. pct and forms at least two long-range ordered structures, Fe3Al and Feu.' Stress-induced ordering internal friction is known to occur in many substitutional solid solutions, but few measurements of this damping effect have been made with alloy systems that have pronounced ordering tendencies. LeClair and Lomer developed expressions relating the relaxation strength of the damping process to the degree of atomic ordering and predicted that stress-induced ordering internal friction would be zero with complete ordering.' This concept was confirmed experimentally by Lulay and Wert using the system cd-Mg It is also consistent with the weak stress-induced ordering peaks observed in P -brass by Artman and in 16 wt pct Al Fe-Al by bert.' It was expected, therefore that the ordering characteristics of the system Fe-Al would strongly influence the stress-induced ordering internal friction exhibited by the experimental alloys. SAMPLE PREPARATION The alloys used in this investigation were induction melted under vacuum using high-purity melting stock. The iron was electrolytically refined Plastiron 101 which contained 99.85 wt pct Fe. The aluminum was a special 99.95 pct pure grade supplied by Alcoa. The only other raw material was spectrographically pure graphite which was used in small quantities as a deoxidant. The amount of carbon used was slightly in excess of the amount required to completely deoxidize the melt; this resulted in residual carbon contents of 0.01 to 0.02 pct in the finished alloys. The vacuum cast 2 1/2-in. diam ingots were hot rolled to 5/8-in. diam round bars. Portions of these bars were hot swaged and hot drawn to 0.050-in. diam wire. Straight pieces of the hot drawn wire were slowly heated to a temperature of 1300°C in a He atmosphere. After holding for 4 hr, the samples were allowed to cool in the furnace. This annealing treatment resulted in grain growth in the samples, the final grain size being about the same as the wire diameter. The grain boundaries were oriented perpendicularly to the wire axis, giving a bamboo grain structure. The existence of a preferred orientation could not be detected in these coarse grained samples. If the samples had a fiber structure, this probably would have been the same in all samples because of similar processing, thus the influence of crystal orientation on the relaxation strength would have been similar in all samples. The aluminum contents of the alloys are listed in Table I. EQUIPMENT The principle of the torsion pendulum was used for the internal friction measuring device. The

Jan 1, 1961

By AIME AIME

IN an address before the New York Section. A.I.M.E., Oct. 20, Alex L. ter Braake, speaking on the tin industry of the Netherlands East Indies, interjected a few remarks, at the chairman's request. on the mineral stock-piling project now before Congress in a bill sponsored by Senator Scrugham. The full text of Mr. ter Braake's paper was published in the Nov. 6 issue of the American Metal Market. Following mention of the buffer stock scheme as applied in the tin industry, Mr. ter Braake continued:

Jan 1, 1943

By Virgil R. D. Kirkham

RECONNAISSANCE of a part of southeastern Idaho and small strip of western Wyoming lying between longitudes 111° and 111° and 45' W., and latitudes 43° and 43° and 30' N., comprising an area of approximately 1330 sq. mi., was undertaken during the summer of 1923 for the collection of data regarding the oil possibilities of the region. TOPOGRAPHY, SETTLEMENT, AND ACCESSIBILITY The entire area lies within the upper Snake River drainage basin. Snake River flows through the northeastern and eastern part of the area in a northwesterly direction. The entire drainage system has been controlled by the structure of the sedimentary beds in the area, which exhibit numerous alternations of hard and soft strata with consequent unequal erosion. The headwaters of the most important streams, as well as many others, flow in a northwesterly or southeasterly direction along

Jan 1, 1925