Search Documents

By E. D. Hummer

During the planning of the fine coal cleaning addition at the Gary, W. Va., Coal Preparation Plant of United States Steel Corp. careful consideration was directed toward the problem of minus 48 mesh refuse disposal. The plant flow sheet included wet screening the raw coal at ¼ in., pumping the minus ¼ in. raw coal to bowl desiltors for desliming, and then cleaning the deslimed raw coal on tables. The material to be removed from the circuit as minus 48 mesh refuse consisted of the minus 100 mesh desiltor overflow thickened in two 120 ft diam thickeners and minus 1 mm screened from the table refuse. Later a flotation plant was added to recover coal from the desiltor overflow, and a classifier replaced the screens to make a sharper size separation of the table refuse at 48 mesh. Today the minus 48 mesh refuse at Gary consists of thickened flotation tailing and thickened spiral classifier overflow. The transportation of large quantities of fine, wet refuse filter cake mixed with jig and table refuse over existing conveying equipment would have been neither dependable nor economical. Filtration was therefore impractical, and disposal of the fine materials was a problem. The decision was to pump the material to storage ponds.

Jan 3, 1965

By John T. Wizzard, R. P. Killmeyer, B. S. Gottfried

The Coal Preparation Branch of the Pittsburgh Energy Technology Center has developed a computer program to calculate the performance characteristics of coal washing devices. This program uses specific gravity analyses of the clean coal and refuse streams as input, and generates dependent and independent performance criteria for the washer. Partition curves are internally represented in a functional form by a Weibull function. Performance criteria generated by this computer program are compared to manually calculated performance criteria for air tables, Dynawhirlpools, Baum jigs, hydrocyclones, and dense medium cyclones. The comparisons show that the computer program gives results in close agreement with the hand- calculated values while greatly reducing the amount of time involved in performing the analyses.

Jan 1, 1983

By AIME AIME

MORTIMER ELWYN COOLEY, dean of the College of Engineering and Architecture of the University of Michigan, has been elected president of the American Engineering Council of the Federated American Engineering Societies. This was announced at a meeting of the Executive Board of the Council held at the Cosmos Club in Washington on Sept. 30. Dean Cooley assumes office at once. The new head of organized engineering is a past president of the American Society of Mechanical Engineers and has a long record of distinguished service in education, under the government and in private capacities. He was born in Canandaigua, N. Y., March 28, 1855, and was graduated from the United States Naval Academy in 1878. With his classmate, Dr. Ira N. Hollis, he was ordered to the U.S.S. "Quinnebaug," then fitting out at the Norfolk Navy Yard preparatory to a cruise in the Mediterranean.

Jan 1, 1921

By G. S. Tint, M. Herman, V. V. Damiano

Dislocation arrays and substructures were studied in cadmium doped zinc crystals using a newly devised etching technique. Cadmium precipitates delineating the dislocations were revealed by etching a surface closely parallel to the (0001) slip plane. Cinephotomicrography of the continuous etching process revealed the three-dimensional aspects of dislocations in the bulk crystal. Dislocation etch patterns were studied in both deformed and annealed crystals after suitable aging at room temperature. The effect of annealing was evidenced by a rearrangement of the dislocations into low-angle boundaries and hexagonal networks. ETCH pit techniques have been used extensively to study dislocations in both deformed and annealed bulk metal crystals. Ideally one hopes to obtain a one-to-one correspondence between the etch pits and the points of emergence of the dislocations at the surface. One then attempts to deduce the way in which dislocations are arranged in the bulk crystal from the arrangement of etch pits on the surface. It is clear that one can obtain only limited information of the dislocation configurations inside the crystal from etch pit studies of single surfaces. Considerably more information is obtained if one is able to follow the course of the dislocations through the crystal using progressive etching technique. Techniques of this sort were used by Gilmanl to study dislocations on the slip planes of NaCl crystals and by Damiano and Tint2 to study dislocation arrangement in zinc crystals grown from the melt. The present paper makes use of a technique first described by Tint and Damiano3 to observe and continuously record the dislocation structures which appear while a crystal surface was being progressively etched. Studies were made on cleaved (0001) surfaces to reveal the dislocations along their length on the surface closely parallel to the slip plane. The technique for revealing segments of dislocations along their length by etching is well known. Wilsdorf and Kuhlmann-wilsdorf4 revealed disloca- tions along their length in aluminum containing a few percent copper, when precipitates segregated along the dislocations. The technique was used by Low and Guard5 to study dislocation configurations on the slip plane in Fe-Si alloys containing carbon. In the present work the technique was applied to zinc containing cadmium since it was shown by Gil-man6 that a cadmium-rich phase could be made to precipitate from supersaturated solutions along dislocations in zinc. Segments of dislocations delineated by the precipitates were revealed by etching a surface prepared by cleaving the crystal. The three-dimensional nature of dislocations and substructures was thus studied from the cinephotomicro-graphic record of the continuous etching process. EXPERIMENTAL Single crystals of zinc containing the order of 0.1 pct Cd were prepared by slowly lowering a graphite crucible containing the melt through a temperature gradient of 15°C per cm at a rate of 1.5 X 10-3 cm per sec. "As grown" crystals were aged for periods of 1 month at room temperature, then cleaved in liquid nitrogen, and etched according to the procedure used by Gilman.' The etchant containing 32 g of CrO3, 6 g of hydrated Na2SO3 in 100 ml of water behaved as a chemical polish for zinc and etch pits were produced at the site of precipitates or inclusions. After the precipitates or inclusions were removed from the surface, the etch pits left behind were eventually polished smooth. This behavior enabled one to continuously observe the surface while the specimen was immersed in the etchant. Best results were obtained when the specimen surface was vertical and the reaction products of polishing were continuously removed by gravitational convection. Some crystals were heavily deformed in excess of 25 pct strain, others were lightly deformed the order of a few pct by compression such that the deformation occurred essentially by basal glide. Some crystals were etched immediately after deformation, others were allowed to age at room temperature for several weeks prior to etching. Heavily deformed crystals were annealed at various temperatures and etched on the cleavage plane immediately after annealing, others were allowed to age at room temperature for several weeks prior to etching. The etched structures of deformed and annealed structures were studied. Similar experiments were conducted on 99.9999 pct pure zone refined Tadanac zinc crystals which

Jan 1, 1963

By Hans Lundberg

GEOPHYSICAL methods as described in technical articles generally fail to answer the questions of prospectors and geologists as to which method they should apply and what information they may expect from their application. This article is an attempt to discuss the use of electrical methods with special reference to the prospecting for orebodies and the map¬ping of geologic structure. Especially on virgin ground, geological reconnaissance should precede electrical prospecting, with the object of outlining carefully the orebearing rock and determining the possibilities of elec¬trical prospecting. No electrical survey will then be carried out on ground which, for geological reasons, may be considered barren or where the electrical meth¬ods are inapplicable. As the success of electrical prospecting depends on the difference in conductivity between the ore and the country rock within which the orebody is inclosed, the conductivity of the two should be considered and de¬termined, if possible. The conductivity of an orebody depends on the distribution of conductive ore minerals and, in addition, on its size (length, width and depth). Most minerals with metallic luster show good electrical conductivity; for instance, the sulfides. Zinc-blende is an exception, but as it is often associated with the ore minerals of good conductivity (for instance, pyrite or galena), there is likelihood also of finding zinc.

Jan 1, 1930

By PHILIP N. MOORE

PHILIP NORTH MOORE was born on July 8, 1849, at Connersville, Ind. His father, a civil engineer, was descended from Henry Moore who came from Ireland in 1773 to live in Washington, Pa. Through his mother, Philip Moore was descended from John North, who came to America in 1635 and settled in Connecticut. The story of Mr. Moore's life as told by himself is given on pages 373-386 of T. A. Rickard's "Interviews with Mining Engineers." He studied at Miami University, where he gained the degree of A.B. in 1870, and A.M. in 1873. In 1920 his alma muter conferred on him the honorary degree of LL.D. He, as a special student, was a member of the class of 1872 at the School of Mines of Columbia University.

Jan 1, 1930

By Murray F. Hawkins

One problem of reservoir engineering is the early estimation of the size of newly discovered reservoirs. Often these reservoirs are the expansion type in which sizeable pressure drops occur incident to the production of small fractions of the oil reserve, above the bubble point, and a material balance equation may be solved to find the reserve. The early form of this equation' considered only the compressibility of the oil. Later Hall2 showed that the compressible nature of the formation rock is a significant factor in production above the bubble point, and he presented a new equation which includes a formation (rock) compressibility term. This note presents a further extension of the material balance equation as applied to volumetric, unsat-urated reservoirs above the bubble point by including a term for the presence and compressible nature of the interstitial water. DERIVATION OF EQUATION During a decline in average reservoir pressure, ?p ?p, — p1 the initial reservoir volume V,, will decrease to some value V, due to the reduction in pore volume as a result of a decline in the hydrostatic pressure within the formation, and v, = V,, [l — cr ?p]......(1) The formation compressibility c, is expressed in terms of change in pore volume per unit pore volume per psi. Simultaneously the connate water within the formation expands from an original volume V,, = S,V,, to a new volume V,, V, = s,v,, [I + c,npl.....(2) The difference [Vp — V,] is the hydrocarbon pore volume at pressure p and may be equated to the volume of the remaining oil, or [N — N,] B, = V,,, [I - C~A;] - S,.Vpi [l + cwnjl.........(3) But the initial oil in place in terms of the initial reservoir volume, connate water, and formation volume factor is Ilividing Equation 3 by Equation 4 eliminates V,, to give,

Jan 1, 1956

By Francis R. Conley, John A. Sievert, John N. Dew

A brief review is presented of the past performance of a number of large, thin, highly permeable reservoirs with low dips in the Bolivar Coastal fields of Venezuela. The performance of these reservoirs indicates that the fluids are segregated vertically within the sand section by gravity. With this assumption, equations are developed which describe the performance under pressure maintenance operations. Methods of solving these equations and results of simple example calculations are presented. Example calculations indicate that under pressure maintenance conditions injected gas tends to {tow preferentially along the top of the sands and that encroaching water has a tendency to flow preferentially along the bottom. The expected performance of segregated fluids is discussed and compared with that of fluids which are uniformly distributed in any sand section. INTRODUCTION The field performance of a number of reservoirs described herein indicates that the fluids are segregated vertically within the sand section by the force of gravity. Thus, it was felt that any method used to predict the future performance of these reservoirs should consider the effects of segregation in the sand sections. A study of the available information on some of the reservoirs suggests that increased recoveries may be expected if the reservoir pressure is maintained by either crestal gas injection or flank water injection. To predict future performance of reservoirs under pressure maintenance operations, a method of analysis was needed which would account for segregation of fluids in the sand sections. Several methods of analysis have been developed to take into account the segregation of fluids in the reservoir as a whole1,3 To our knowledge no method considers segregation of the fluids within sand sections in the manner indicated by the past performance of several reservoirs in the Mara-caibo Basin. This paper outlines part of the work done in studying some of these reservoirs and contains a description of their performance characteristics. The analysis presented is restricted to pressure maintenance conditions, since space limitations prevent a full discus- sion of the development of the mathematical relations and the various methods of solving them. Only a sketch of the development of the mathematical relations is given. The various methods of solving these relations are pointed out, but the actual determination of solutions to various problems are omitted except for one example. It is felt that these results may aid in the study of reservoirs outside the Maracaibo Basin. Some concepts on which the present analysis is based are outlined by D. N. Dietz. However, the analysis presented herein includes several factors not considered by Dietz: (1) variations in permeability and in the cross section, (2) various shapes of the cross section, and (3) the production of fluids. Also, the mathematical development presented by Dietz differs considerably from our corresponding analysis. RESERVOIR CHARACTERISTICS The reservoirs under consideration, large and thin, with low dip and high permeability, are large to the extent that they contain from 0.5 to over four billion bbl of oil initially in place. The section thicknesses vary from 100 to 400 ft and the lengths from 10,000 to 40,000 ft. Thus, a length-wise cross section of the producing formation appears to be long and thin. The dip angles vary from 0 to 6 degrees and the average permeabilities vary from 0.5 to over three darcies. The reservoirs contain from 20 to 50 per cent shale inter-laminated with the productive sands. Most shale breaks within the major sands do not correlate from one well to the next, and correlation is often difficult, even between wells drilled from the same location. However, it is often possible to correlate the shale breaks between major sands for some distance. Herein we are concerned with the performance of reservoirs containing oil of gravities over 20" API. Past reservoir performance indicates good pressure communication and, in cases where pressure sinks have developed, large amounts of fluid migration have occurred. Few of the reservoirs have had initial gas caps, but also, few have been found to be highly under-saturated. Due to gravity segregation, secondary gas caps usually form before the pressure has been reduced more than 25 per cent of its initial value. The effect of gravity has not only been apparent on a reservoir-wide basis, but has also caused segregation of the reservoir fluids in productive sections. Proof of this is found from the results of selective well tests, workovers, and electric and various other types of logs. Evidence that

By J. Mote, P. Ward Flynn, J. E. Dorn

The effect of strain and strain rate on the critical resolved shear stress for prismatic slip in specially oriented single magnesium crystals was determined over a range of temperatures in an effort to identify the thermally activated strain-rate controlling dislocation process. Below about 450°K prismatic slip was preceded by twinning and fracturing. Above 450°K extensive prismatic slip was obtained followed by fracturing. Neither the Peierls&apos; mechanism nor the dislocation intersection mechanism can account for the observations. The data, however, are in good agreement with the dictates of Friedel&apos;s theory for cross slip to the prismatic plane. PREVIOUS investigations on single and polycrys-talline magnesium have resulted in the identification of the mechanisms of plastic deformation summarized in Table I. The-only well-confirmed mechanisms are {0001}, (1010}, (1011) slip plus (1012) twinning. The other twinning modes were only tentatively established and additional investigations are required to further confirm their operation. As noted in Table I, slip in this hexagonal close-packed metal invariably occurs in the direction of greatest atomic density, revealing that the Burger&apos;s vector for-active slip dislocations is always given by b = a/3<1210>. Slip is easily induced on the basal plane, and recent investigations have shown that the strain-rate controlling mechanism at low temperatures is the thermally activated intersection of the glide dislocations with dislocations threading the basal plane. In contrast, very little is known about prismatic slip. It has been reported to be active at points of stress concentration in polycrystals below

Jan 1, 1962

By E. T. Turkdogan, L. S. Darken, R. G. Olsson, H. A. Wriedt

Several aspects of the calcination of Michigan limestone were investigated: the rate of calcination of limestone spheres with diameters from 1.8 to 14 cm at temperatures from 800° to 1200°C by a thermogravimetric method; the temperature profile across limestone during calcination; the excess pressure developed in the interior of the stone during calcination; the pore surface area, pore volume, and effective gas diffusivity in burnt lime; and the microstructure of polished and fracture surfaces. It is found that, over a wide range of experimental conditions, the difference between the surface and center temperatures remains essentially unchanged during the latter half of calcination. From the rate of weight loss after about 50% calcination, the value 0.00126 cal per cm sec degree is found for the effective thermal conductivity of burnt lime. From the excess internal pressure measurements, i.e., 0.4 to 6 cm Hg at 800° to 1200°C, the permeability of burnt lime is estimated to be within the range 8 X 10-&apos; to 5 X 10&apos; sq cm. With increasing temperature and time of calcination, the pore structure of burnt lime coarsens as indicated by a decrease in the pore surface area, pore volume, and an increase in the average pore size. For the temperature range 600° to 835°C the ratio (effective gas diffusivity/molecular diffusivity) is about 0.18.

Jan 1, 1974

By D. U. Deere, F. D. Patton

Introduction A close relationship exists between the geologic investigation and the stability analysis of the slopes of an open pit mine. One significant result of this relationship is that the stability analysis is no better than the assessment of pertinent geologic factors that enter into the analysis. In some slope stability problems the engineering solution becomes obvious once the geologic framework is established. In other cases, establishing the geologic framework is only the first stage in the process of analysis. However, even in these cases the geology should not be neglected once the analysis is made. The geology should be periodically reviewed when new slopes are excavated. This will help ensure that the basic assumptions for the analysis have not changed and will permit changes when new conditions are encountered. In recent years improved methods of stability analysis have been accompanied by advances in laboratory testing techniques and new knowledge of the shear strength of rock discontinuities. At the same time there have been improvements in field geological descriptions. As more experience is gained in analyzing and predicting the stability of rock slopes, the importance of certain geologic factors has become more apparent. Some of these factors were described in a paper given at the Open Pit Mining Symposium in Johannesburg, South Africa in September 1970 (I). This paper includes many of the points covered at that meeting but with additional emphasis on the significance of the major geologic structures. Other papers given at the South African symposium also considered geological and hydrogeological factors in slope stability analysis (2) (3) (4) (5) (6). This paper first describes the approach to a slope stability problem including assessment of the relative roles of field geology studies, laboratory testing, stability analyses, and continued slope monitoring studies. Next, is described a framework which has been found useful for classifying or separating the several types of slope stability problems encountered in open pit mines. The principal geologic factors in slope stability problems in rock are discussed and brief comments are made on how these factors distinguish stability problems in rock slopes from those normally encountered in soil slopes. The over-riding control of major geologic structures, especially faults, in most slope stability problems is emphasized. In this regard the relative importance of statistical studies is contrasted with knowledge of the positions of key structural

Jan 1, 1971

By W. H. Bassett

Beads of metal frequently appear at the ends of cast-copper wire bars and on the sides of wedge cakes near the top. These are richer in cuprous-oxide than the rest of the casting. A micrographical study of these exudations has been made. It is suggested that the material is forced through the surface while the copper is solidifying. If not eliminated in process of manufacture, it shows on the finished polished sheet copper in patches differing in color from the main body of the sheet. FIGURES 1 to 4 show the copper exudations, at different magnifications, as they appear on the ends of cast wire bars, and on the sides, usually near the top, of wedge cakes. Sometimes the exudations are in fine "drops;" at other times, large masses of the material are found. Microscopic examination of the copper exudation indicates that it is high in oxide and of eutectic proportions. Because of the difficulty of securing a suitable sample, the protuberances have not been analyzed chemically; but the spectroscope shows no indication that there are any more metallic impurities present than in the balance of the copper. The lowest copper plus silver content of the coppers studied for this? paper was 99.914 per cent.; the highest, 99.966 per cent.; so the oxygen content of the whole casting would be well under 0.07 per cent.

Jan 2, 1926

By W. C. Elli, M. E. Fine

YOUNG&apos;S modulus of elasticity in metals ordinarily decreases with rising temperature. The range of the thermoelastic coefficient at room tem- 1/E dE/dT perature (temperature coefficient of modulus, is illustrated1 by the values for tungsten and hard-drawn aluminum, —95 and —1220x10-6 eg C-1. However, a nearly zero thermoelastic coefficient is observed in some ferromagnetic alloys over a limited temperature range. In these alloys, as the temperature is raised, an increase in modulus arising from loss of ferromagnetism compensates the normal decrease. Iron-nickel alloys containing 36 to 52 pct Ni behave in this manner. In the present investiga- tion, the dependence of the modulus and thermo-elastic coefficient on cold working and annealing were studied in iron-nickel alloys in this range of nickel. Although these alloys, when fully annealed, have a coefficient near zero over a very small temperature interval, the temperature range of low coefficient can be extended greatly by straining and then stress-relief annealing. The modulus of face-centered cubic iron-nickel alloys annealed at 1000°C does not vary linearly with composition at room temperature but, as shown by the solid line of fig. 1, from Koster,&apos; is minimum at 40 pct Ni and maximum at 87 pct Ni. The modulus increases with applied magnetic field but retains the minimum near 40 pct Ni. Schematic change of modulus with temperature for three compositions is shown in fig. 2.&apos;. &apos; With increasing temperature, the slope becomes less negative, goes through zero (temperature of minimum modulus for the alloy), becomes positive, and resumes its normal negative value above the Curie

Jan 1, 1951

By Heinrich 0. Hofman

A T THE meeting of the Board of Directors on June 24, Prof. Heinrich O. Hofman was elected an honorary member of the American Institute of Mining and Metallurgical Engineers. Professor Hofman is best known to the world at large for his publications, and in this respect he is to this generation what Schnabel was to the previous one. The first edition of Professor Hofman&apos;s "Metallurgy of Lead and Desilverization of Base Bullion"; was published in 1893; the fifth edition in 1898. In 1913, he published his work on "General Metallurgy;" this was followed by "Metallurgy of Copper" in 1914, and a revised and enlarged edition of the "Metallurgy of Lead" in 1918. "Metallurgy of Zinc and Cadmium" is now in press. He also published, through the Massachusetts Institute of Technology, "An Outline of the Metallurgy of Iron and Steel" for students&apos; use. Since the founding of "Mineral Industry" in 1892, he has been continuously the annual contributor on the metallurgy of lead, and all Institute members know that his contributions to the TRANSACTIONS have been liberal in the extreme. It is through this medium that the results of the extensive research work, which he has always carried on in connection with his work at the Massachusetts Institute of Technology, have been published. Of the greatest importance are his papers dealing with the formation temperatures of slags, but many other metallurgical subjects have been covered.

Jan 1, 1921

By T. Carl Shelton

The coal industry of the United States in 1967 had reasons to be both exuberant and concerned about its present and future role in the economy of the country. Continuing a momentum that began in the early 1960&apos;s, the industry has moved ahead in providing competitive customized products to strengthen its long-term domestic and foreign commitments, and has maintained with steady progress its position as a major supplier of energy. On the other hand, the industry must overcome air- water pollution and conservation-reclamation problems that have been identified by 1967 legislation. Throughout the year, the industry was characterized as "progressive," "healthy" and "dynamic." To have been termed a "growth industry" in 1967, is an accolade the coal industry can accept with pride. Culminating its efforts throughout the decade, the industry has emerged with a competitive image that is representative of its future strength.

Jan 2, 1968

By R. A. Greenkorn, R. C. Smith

Hele-Shaw cells are used to model creeping flow through porous media (where Darcy&apos;s law is valid). The effects of inertia on flow about obstructions in a Hele-Shaw cell can be calculated by a perturbation method if one can determine a solution to Laplace&apos;s equation. Results of a computer solution for flow about circular, square and elliptical obstructions are presented. These results show that or a modified Reynolds number of less than I, the inertia terms are small; and for values of less than 3, the average streamline predicts the ideal flow. Therefore, the analogy might be used for studying flow in porous media up to a modified Reynolds number of at least 3. INTRODUCTION The nature of fluid flow in porous media is of interest in the fields of soil mechanics, ground water flow, petroleum production, filtration and flow in packed beds. Because it is very difficult to study the phenomenological behavior of flow in porous media, homologs and analogs are used to study flow characteristics. A Hele-Shaw model, made of two closely spaced plates - usually glass — is often used as an analogy to two-dimensional flow in porous media. Hele-Shaw2 showed experimentally that the streamline configuration for creeping flow around an obstacle located between two closely spaced parallel plates is the same as for two-dimensional, ideal flow about the same obstacle. Stokes7 verified these observations mathematically. The usual equation of motion for flow in porous media is Darcy&apos;s law. The form of the mathematical statement of Darcy&apos;s law is identical, within a multiplicative constant, to the expression for the average velocity over the plate gap in the plane of a Hele-Shaw model. These models may be used to describe flow in both homogeneous and heterogeneous porous media. In the mathematical proof of the Hele-Shaw analogy it is assumed that the convective terms in the Navier-Stokes equations are negligible and that the equations of motion degenerate to Laplace&apos;s equation, with pressure the dependent variable. Whenever a Hele-Shaw model is used as an analogy to flow in porous media, .the validity of this assumption is in question. Riegels5 showed that if convection is not neglected, the velocity distribution around a cylindrical obstruction in the flow field depends on a Reynolds number, the plate spacing, and a dimension characteristic of the obstacle. Riegels&apos; solution, a perturbation solution, uses the boundary condition that the flow rate into the obstacle averaged over the plate gap at any point on the obstacle is zero. The method requires that a solution to Poisson&apos;s equation for the perturbation pressure be found. Riegels evaluated this solution for the case of the cylindrical obstruction. His method may be simplified by eliminating the need for solving Poisson&apos;s equation for the perturbation pressure. Instead, an analytic expression for the perturbation pressure gradient is obtained (valid for arbitrary shapes) and used to eliminate pressure from the equations for the perturbation velocities. The results show, for symmetrical shapes, that if NRe < 1, the convective acceleration terms are small, and that the average velocities represent ideal flow up to at least NRe = 3, where: L is a characteristic dimension of the obstacle perpendicular to flow, b is the plate spacing, u is viscosity, v, is velocity of approach and p is density. THEORY* Incompressible fluid flow through a Hele-Shaw model and a porous medium are analogous because the equations for the average velocity components in two-dimensional flow are identical if:

Jan 1, 1970

By Robert T. Chapman

The revolution in equipment for blasthole drilling, ore loading, and ore hauling has been so rapid over the last ten years that it has generated an important new profit potential in the mining industry. With the new high-capacity machinery now available, it is possible for a mining enterprise to earn a profit from larger and lower grade orebodies than ever before despite the ever-increasing burden of rising costs. Just what such equipment can accomplish when coupled with improved mining practice has been demonstrated with startling success at the No. 1 mine of Minerva Oil Co. near Cave-in-Rock in Hardin County, Ill. The No. 1 is an underground operation which has been producing fluorspar and zinc ores and concentrates continuously since 1944. A few years ago, when the mine neared the familiar cross-roads where rising costs, increasing tonnages, and relatively static product prices converge, company officials decided to bolster the operation with new mobile equipment. They chose three machines which proved so effective that output at the No. 1 doubled between 1963 and 1965,while costs dropped by about 40% in the same period.

Jan 11, 1966

By TRUMAN S. FULLER

THE GREAT INTEREST in decomposition and trans- formation, so evident in the study of alloys during the last two years, was reflected in the many papers on this subject, presented at the first session of the Institute of Metals, Tuesday morning. Dr. F. A. Thomson, of Montana State School of Mines, presented the first paper by C. Wilson, H. F. Silliman, and E. C. Little, "Rate of Precipitation of Nickel Silicide and Cobalt Silicide in the Hardenable Copper-nickel-silicon and Copper- cobalt-silicon Alloys." Dr. R. F. Mehl, in discussing this paper, stated that the title was somewhat deceptive, as it indicated that the rate of precipitation is determined; the method used is a measurement of electrical conductivity and hardness, neither of which is suitable for a quantitative measurement of rates of reaction or precipitation in the solid state. Hardness is also uncertain because it depends so much upon particle size. Of the various methods proposed for the study of rate of reaction and precipitation the evaluation of volume of reaction produced from the area of photomicrograph is the best.

Jan 1, 1933

By John L. Schroder

The demands for increased productivity on the 1967 coal industry have generated new operating trends and fresh approaches to old methods, which have enabled the industry to keep pace with the expanding economy. Changes, while not radical in concept or design, have been plentiful and are marked by the refinement of the already tried, tested and proven. Perhaps not since World War II have there been demands on equipment manufacturers to design and deliver such diversified types of machines as those required by the industry in the past year. Equipment developments-following a plan which calls for higher productivity, lower maintenance costs and greater machine availability- have tended more toward increased horsepower and heavier, more rugged equipment. Electrical and mechanical components, designed in many instances with maximum reliability rather than initial costs as the main criterion, have contributed to the improvements in over-all performance. High-strength, specialty steels are finding use in a wide range of equipment applications. The horsepower capacity of electric motors being installed is more frequently being rated on a continuous basis rather than the former one hr or less and, as a result, fewer failures now occur because of overloading. These developments reflect the pyramiding cost of equipment down-time and represent definitive progress in reducing the magnitude of the problem.

Jan 2, 1968

By N. J. Grant, H. Brunner

This paber is concerned with the determination of equations relating elongation to the amount of shear taking place both along grain boundaries and in slip planes of poly crystalline aggregates during creep. Certain discrepancies with previously used equations are pointed out. Grain boundaries were observed to become serrated during creep, but it is shown that this does not necessarily prevent further grain boundary sliding. Direct obser-vations of subgrain boundary ingration lead to the conclusion that this migration facilitates sliding along serrated grain boundaries. It is bointed out that the state of stress at triple boints is still unknown. MOST of the mechanisms of deformation contributing to elongation are shear processes, such as slip, kinking, grain boundary sliding, and twinning. For quantitative investigations of individual deformation mechanism it is necessary to know the equation which permits the calculation of speci-tnen elongation from measured amounts of shear. This calculated elongation must then be compared with the observed total elongation. The authors&apos; special interest concerned grain boundary sliding during creep. Although this subject has already been investigated quantitatively by McLean,&apos; Rachinger,&apos; and Fazan, Sherby, and Dorn, calculations indicated that none of the equations used thus far to relate shear with elongation were sufficiently well founded. A basic study of this relationship was thus made and the results of this study (which do not entirely agree with those previously used) are presented. Most of the ideas set forth apply not only to grain boundary sliding but to other mechanisms of shear as well. THE SPEAR-ELONGATION RELATIONSHIP Basic Models—The relationship between shear and elongation is trivial in the simplest case of shear, which is shown in Fig. l(a). The vector A; designates the displacement across the shear interface, and Au, and Aut are its components parallel and normal to the tensile direction, respectively. It is evident that the specimen elongation due to shear is equal to the longitudinal component of the shear vector, and it should be noted that the normal component does not contribute to the elongation of the specimen (there are, of course, two normal components in a three-dimensional model). The model shown in Fig. l(b) may be applied to mechanical twinning and to subgrain boundary tnigration. In this case the width (h) of an already existing shear band increases by the migration of an interface, but the shear angle y (angle of mis-orientation in the case of a subgrain boundary) remains constant. The geometrical relationships indicated in Fig. l(b) permit this case to be reduced to the one shown in Fig. l(a). For the resulting elongation A6 we find: where AV/V = fraction of the volume of the specimen swept by migrating interfaces , and 1 = length of specimen. Thus, assuming for example that the angle of mis-orientation is 1 deg, and that P = 45 deg, we find that the specimen elongates 0.87 pct of its length if the entire volume of the specimen is swept once by such a subgrain boundary. An example of deformation by migration of subgrain boundaries is shown in Fig. 2. The specimen shown was repolished after 9.8 pct creep strain and the test then continued for another \ pct. Since the shear vector has, in general, a component normal to the surface, subgrain boundary migration results in the formation of an inclined band delineating the region swept by the subgrain boundary. These inclined bands become clearly visible when observed with oblique illumina-

Jan 1, 1960