Search Documents

By M. Muskat

A theory has been developed describing the behavior of wells and reservoirs producing by the action of bottom water drives. It is assumed that the pressures are maintained above the bubble point, and that the permeability to viscosity ratio of the water in the flooded zone is the same as for the oil in the oil-saturated pay. Accordingly, the treatment is based on the homogeneous fluid potential theory. The effect of the difference in density between the oil and water is neglected. .4fter deriving the proper potential distrihutions, the nature of the rise of the water-oil interface below the producing wells is calculated. The primary clean-oil-production phase is expressed in terms of the displacement efficiency, defined as the fraction of the pay flooded out by the rising water table at tlle time of first water entry. The variation of this displacement efficiency is calculated as a function of the well spacing, pay thickness, the ratio of the horizontal to vertical permeability, and the well penetration. The important parameter, other than the well penetration, is found to be the ratio of the well separation to the thickness of the oil pay multiplied by the square root of the ratio of vertical to horizontal permeability. It was found that the displacement efficiency continually decreases as this parameter increases, and for values of the latter >3.5, the efficiency varies inversely as the square of the parameter. It also increases with decreasing well penetration. Perhaps the most striking result of this phase of the analysis is the conclusion that in order to explain the delay in entry of water in wells producing by bottom water drives for periods longer than a few days normal production, with drawdowns large compared with the differential density head between the oil and water, it is necessary to assume that the vertical permeability is a very low fraction of the horizontal permeability. An analysis is also given of the production history after the water has broken through, on the assumption that the production mechanism and details of the flow distribution continue to be the same as during the phase of clean-oil production. As is to be expected, it is found that the water cut will increase at an accelerated rate as production proceeds. However, the initial differences between systems of different well penetrations or well spacings with respect to the total clean-oil production gradually decrease in terms of the variation of the water-oil ratio with cumulative production. In particular, by the time the water-oil ratio has reached values of the order of 5 or greater the cumulative recoveries will generally differ much less among various producing systems than their corresponding clean-oil recoveries. Introduction On the basis of elementary geological principles, one may classify effective water-drive fields in two groups. In the first, the entry of water into the oil-producing formation may be characterized as an edge-water encroachment. This term is used to suggest that the motion of the water proceeds largely in a direction parallel to the planes of stratification. This type of water intrusion occurs usually in thin producing zones and in strata lying along structural flanks of appreciable dip. In the second group—"bottom water-drive" fields—the water-oil interface lies in a plane of zero or slight inclination to the

Jan 1, 1947

By A. L. Fentress, P. R. Bucky

The purpose of this paper is to present a scientific method for determining the proper span and shape of roof for safe and economical mining; at present, these two vital factors wherever pillars are left to support the roof are determined by local practice or general experience. To develop the method described here, experimental laboratory work was done. The arch adopted was a segment of a circle, a flat roof being considered an arch with an infinite radius. Hitherto, arches have been used underground without the background of stress analysis that generally precedes arch construction on the surface. In many cases results have not been as expected, because of the lack of knowledge of the factors affecting its strength and behavior. A theoretical and experimental study of arches should furnish information that will make it possible to design safe and economical surface structures as well as underground openings. For example, on the subject of mine drifts and tunnels, the present idea is that arching their backs increases their strength; this paper will indicate that this is not always true, and if it can be shown that under certain conditions arching becomes unnecessary an economic saving will result. In room-and-pillar work a question may arise as to whether arching the roof and gobbing the excavated material will result in timber saving, and a decrease in the dangers from falls of roof. It is to be distinctly understood that each mine must be treated as an individual problem, and that answers to these questions and many others can now be found after experimental laboratory data have been obtained. Mine-Arch Structure Fig. 1 shows the elements that affect the strength or behavior of the experimental arch. They are the span, crown thickness, radius of curvature, rise and restraint. The restraint in all cases was made sufficient to cause the arch to fail without displacing the restraining sides. Fig. 2a is a photograph of a model arch prepared for testing in the centri-

Jan 1, 1934

By R. K. Hopkins

For a great many years fusion welding has been used in and around petroleum refineries, but it is only within six or seven years that the more important pressure vessels have been constructed by this process, because before that time the properties of fusion welds would not with-stand such rigorous service. Since the adoption of fusion welding for the construction of this equipment, the refiner has required pressure vessels suitable for operation over a very wide range of conditions. On the one hand, vessels must operate at extremely high temperatures, in the range of 950° to 1000° F., and on the other vessels must be suitable for operation at sub-zero temperatures down as low as -75° F. Also, vessels are required suitable for operation at pressures upwards of 1000 lb. per sq. in., and as low as a 29-in. vacuum. In addition, vessels are required to withstand the attack of very corrosive mediums. It has been a rather difficult task for the fabricator to meet all of these require-ments, but as a result of the extensive research carried on by steel manu-facturers and several fabricators of class I vessels, practically all of these demands have been met. In order to meet the refiners' requirements for this wide range of conditions, the fabricator has worked closely with the metallurgist. This has enabled him to choose the proper base metal for each service condition, but it has been the fabricator's problem to develop a welding rod and welding technique, as well as a heat-treatment, that would produce in the welded vessel characteristics in and around the weld comparable to those in the base metal. Where corrosion is not a serious problem, and where the operating temperatures are not too high, ordinary carbon steel has served very well. But when corrosion is serious, and/or when the temperatures are either very high or very low, it is necessary to use some form of alloy steel to give satisfactory service.

Jan 1, 1935

By J. D. Ridge

The geologic setting and mineral relationships of seven European massive sulfide deposits that more or less conform to the bedding of the largely noncal-careous sedimentary rocks and/or bedded volcanics in which they are found are considered here. These orebodies consist largely of massive beds or lenses of sulfides usually surrounded by halos of disseminated sulfides and distorted by tectonic activity. The formations containing these deposits have been metamorphosed in varying degrees at times subsequent to their lithification. The ore-forming process is thought to be essentially volcanic, with the ore constituents being brought to the shallow-water site of deposition through tectonic fissures from magma chambers at depth as gases or relatively concentrated hydrother-mal solutions. Certain European ore deposits of base metal sulfide have previously been considered to be of hydro-thermal or magmatic origin, but today a number of European mining geologists consider them to be syngenetically produced. In an effort to provide American geologists with some idea of the reasons behind this change in thought, the geological settings of seven of these deposits have been studied. These are: Ldkken, Meggen, Rammelsberg, Ergani-Maden, Outokumpu, Boliden and Roros. These deposits lie in bedded rocks that have undergone metamorphism from causes not universally agreed upon; most of the formations were originally shales, and may have been intercalated with limey and occasionally quartzitic beds, volcanic tuff, agglomerate, extrusive lavas and usually basic intrusives. Deposits of the conformable type, however, are not confined to these rock types but may be in calcareous and associated igneous rocks or almost entirely in volcanics. These deposits may be closely associated in space with igneous rocks that, again, are usually basic types. Although the ages of the enclosing rocks range from mid-Precambrian (Boliden and Outokumpu) to Eocene (Ergani-Maden), the bulk of them are Paleozoic, with two (Meggen, and eammelsberg) being upper middle Devonian and two (LØkken and RØros) being Cambro-Ordovician. Geographically, two are in West Germany, four in Scandanavia and one in Turkey. Of the seven deposits, six are mined for copper, with three of these also producing zinc, and two lead; one is mined for zinc and minor lead. In the discussions of the seven conformable deposits that follow, I have attempted to present as uniform a treatment as their varying characters will permit. For each deposit, I have considered the stratigraphy of the area, its major structural characteristics, the form of the orebodies, their mineral content, and the origin of the ore. In the last of these subdivisions, I have presented only the viewpoint of those who believe the ores to have been formed by syngenetic processes, processes that went on at the same time as those which produced the beds that enclose the ores but that are not, in the deposits in question, thought to have been sedimentary in the strict sense of the term. The materials of which these orebodies are composed, it is suggested, did actually collect by falling through sea water to the floor of that portion of the sea in which they accumulated. The ore constituents, however, are believed by a considerable number of European geologists to have been added to the sea water from intratelluric sources, probably igneous magma chambers, as exhalations — hydrothermal solutions or volcanic gases. The effect of the encounter with sea water on these ejected gases or water-rich vapors was to precipitate their potentially solid constituents with great rapidity; they were deposited so quickly, in fact, that the amounj of normally accumulated mechanical or chemical sediment deposited over the same period of time was essentially negligible. The ores formed in this manner, however, are generally interbedded with normal sediments or with lava flows, or with any combination of these two types of rock-forming materials. Such departures as these deposits may have from their original mineral content and attitude are thought to be directly related to the degree of dynamic or static metamorphism that they may have undergone after their accumulation. I have not attempted here to present alternate hypotheses to that of so-called exhalative sedimentation although, of course, such exist and, in my

Jan 1, 1963

By E. Miller, N. Chou, K. Komarek

The solid solubilities of the compounds PbS, PbSe, and PbTe have been determined by equilibrating single crystals with two phase alloys. The solubilities were determined by measuring the Hall coefficient of the equilibrated samples. The observed maximum deviations from stoichiometry on the lead rich and the chalcogen-rich side of the phase fields were: at. pct excess Pb at pct excess S at 850°C; PbSe--4 x 10'" at. pct excess Pb at at. pct excess at 800°C; and PbTe-2.8 x 10 4 at. pct excess Pb at 780°C, 10"1 at. pct excess Te at 720°C. The previously developed theory of retrograde solubility has been expanded to include intrinsic disorder in the compounds, and the experimental results are in agreement with the theory. THE solid solubility limits of intermetallic semiconducting compounds are of considerable interest, since many of these compounds have potential use as thermoelements in thermoelectric devices, as infrared detectors, or in semiconductor devices. The solidus curves of a significant number of these compounds have been reported to be retrograde with the maximum solid solubility occurring between the eu-tectic and the maximum melting temperatures. In a previous paper,' equations were derived which permit calculation of the maximum solid solubility of an AB compound exhibiting retrograde solubility. Derivation of these equations was based on the assumption that the compound is a nondegenerate semiconductor at the temperature under consideration, that the defects were unassociated, and that the vibrational contribution to the entropy of the compound could be evaluated by the Einstein approximation. It was shown that at the temperature of the maximum solid solubility The entropy term ASS is composed of the entropy of formation of the solid stoichiometric compound (AS$)*, and the entropy due to deviations from stoichiometric composition which is the sum of a con-figurational term (aS*), a vibrational term (AS,), and an electronic term (AS,). In the previous paper the positional entropy was evaluated considering the con- N. CHOU, Member AIME, formerly Graduate Student, New York University, N. Y., is with IBM, Yorktown Heights, N. Y. K. L. KOMAREK, Member AIME, formerly with New York University, is Professor, Department of Inorganic Chemistry, University of Vienna, Vienna, Austria. E. MI LLER, Member AIME, formerly with New York University, is Associate Professor of Mechanical Engineering, California State College at Long Beach, Calif. The paper is based on a thesis submitted by N. CHOU to the Graduate Division, School of Engineering and Science, New York University, in partial fulfillment of the requirements for the degree of Doctor of Philosophy in Materials Science. tributions from defects arising from deviations from stoichiometric composition. The derivation is generalized in the appendix to include intrinsic disorder. The electronic entropy term is also recalculated in the appendix. Of the various semiconducting compounds, the solidus curves of Pbs,' and ~b~e,~ have been most extensively studied. The solidus of PbSe has also been determined, but the temperature of maximum solubility has not been accurately established.5129 The present investigation was undertaken to compare the experimental solid solubility data for these systems with the values predicted theoretically. Since the temperature and composition of the maximum solubility of PbSe has not been accurately determined, experimental emphasis was placed on determining the solidus curves for PbSe in the region of maximum solubility, although experiments were also performed on PbS and PbTe at several temperatures. X-ray diffraction studies were also made on carefully prepared powder samples of PbSe to determine the variation of lattice parameter with composition. EXPERIMENTAL PROCEDURE The procedure of Brebrick and Allgaier was employed for determining the solidus data. Monocrystal-

Jan 1, 1970

By E. L. Tucker

IN THE metallurgy of precious metals, it has been standard practice for years to use cyanogen compounds, so it was but natural that early investigators in the field of flotation should consider these compounds as possible flotation reagents. In Australian Patent 9508, of 1913, alkali cyanides were described as suitable reagents for the separation of heavy sulfide minerals, the reagents being employed either in an alka-line or neutral circuit. In U. S. Patent 1236501, of 1917, to John M. Tibbet, the use of cyanide in conjunction with soda ash or lime is described. One of the claims of this patent reads, "An improvement in the cyanide process for the treatment of ores comprising, mixing the ore with cyanide solution and oil and alkali: emulsifying the oil in the presence of the ore, the alkali and the cyanide solution, floating a portion of the values in the pulp by producing gas bubbles in the mixture-and removing the values floated." More recently, Sheridan and Griswold, in U. S. Patents 1421585 and 1427235, describe a somewhat similar process and have, successfully introduced it in. the mill of the Timber Butte Milling Co. U. S. Patent 1429544, of 1922, to Stevens, describes the use of double cyanides of copper, zinc, and lead. The success of cyanide as a reagent in the differential flotation of lead and zinc sulfides in highly complex ores is proof that these patents have a solid foundation.. Although the technique of their application to particular ores has been worked out in many cases, no one, so far as is known, has attempted to describe the nature of the action of the cyanide or to determine the ideal conditions for its, application. It was the purpose of the present investigation to gather information on these points. Naturally this would have been an exceedingly ambitious.

Jan 8, 1925

By C. O. Rison

HIGH explosives, particularly nitroglycerin, have been used in torpedoes for the purpose of shooting oil and gas wells for more than 60 years. The early history of the oil industry in Pennsylvania is not clear as to who actually torpedoed the first well, although in 1865 the Roberts Torpedo Co. procured a patent covering the process. Gunpowder was first used, although nitroglycerin was substituted shortly afterwards. Wells are shot for the purpose of increasing the flow of oil and gas A shot-hole in the producing horizon, with its contributory fissures and fractures, increases the area of and stimulates drainage into the hole. The shot-hole also acts as a collecting basin from which the oil is pumped. As a rule, hard or close-grained sands or limes are shot, other more or less porous and soft formations usually do not require shooting. and might be injured by blasting. Shooting is also resorted to in mechanical trouble such as straightening crooked holes, sidetracking pipe or tools, and for severing frozen strings of casing or drill pipe. Explosives arc also used sometimes to extinguish oil or gas-well fires although that work, which involves unusual conditions and methods, does not properly come within the classification of oil-well shooting. Some Factors to Be Considered in Shooting Wells Although nitroglycerin has been used extensively for more than half a century in shooting oil and gas wells, there is still a great deal of uncertainty as to the proper method of shooting or the amount of explosive required to produce best results in a particular formation. The possibility of shooting unproductive or cavey formations above or below the productive horizons, shooting into lower water, destroying casing seats, and the splitting or collapsing of casing strings, are factors that require consideration. The engineering departments of a number of the larger oil companies are making a study of methods of shooting, and the amounts of liquid nitroglycerin or other explosives required in shooting various productive

Jan 1, 1929

By C. B. Alcock, M. G. Hocking

The kinetics of the growth of sulfate layers on blocks of Cu20 has been studied between 688" and 800°C. At 788c the over-all weight increases followed the parabolic rate law, with k = 216 30 sq mg per cm4 min, using a 1:1 entering gas mixture of SO2:02. At 757 after an initial linear period the parabolic rate law was followed, with k = 57.8 10 sq mg per cm4 min. The gas mixture required a platinum catalyst to produce the maximum SOs pressure. The sulfation rate at 757' and 788c was high until all the CUZO had changed into a core of CuO, when it became very much lower. At 757°C marker experiments showed that the sulfates (CuO. CuS04 and CuSO4) grow outwards from the oxide surface, but CuO. CuS04 mixed with CuO was found beneath the markers. At 688 markers were found at the CuO. CuS04/CuS04 interface. Visual observations at 757 showed a liquid eutectic moving beneath the sulfate surface. causing very rapid sulfation and extruding to solidify as thick 'needles" up to 8 mm long. Marker experiments have shown conclusi.cely that CuO grows on Cu20 in air by the outward migration of copper. ThermODYNAMIC measurements on the sulfate and basic sulfate of copper, reported recently,' are followed here by measurements of the rates of formation of these sulfates on cuprous oxide, in order to provide a background for the understanding of roasting processes. peretti2 and McCabe and Morgan3 have shown that the phase Cu20 lies next to Cu2S when the sulfide is roasted under conditions where sulfates will be formed. Since this would present too complex a system for kinetic study, the present work4 has been based on the kinetics of sulfation of the oxide phase. The results of a study of the kinetics and mechanism of the sulfation of cobaltous oxide have recently been reported.4,5 Results on the sulfation of cuprous oxide have also appeared,6 but are at variance with those to be reported here. This seems to be because the previous workers6 did not obtain constant SO3 pressures from the SO2/O2 sulfating gas mixtures used, as will be discussed later. Wadsworth, Leiter, Porter, and Lewis found that the sulfates produced when SO2/O2 mixtures are passed over Cu20 at red heats are CuS04 and the basic sulfate CuO.CuSO4. When the decomposition of CuS04 was followed' by differential thermal analysis, a stage corresponding to CuO .CuS04 was reached before decomposition into the oxide occurred. APPARATUS The vertical furnace used for quantitative studies was a conventional resistance-heated and propor- tionately controlled furnace with an even zone (1 deg) which was 4 cm long. The gas mixtures of SO2 and 02 were made by mixing measured flows from capillary flowmeters and drying over phosphorous pentoxide before passing them into the Pyrex top-piece of the furnace assembly. A mullite tube of bore 2% cm was used as reaction vessel and at the bottom of this tube was a trap for SO3, which condensed as a colorless liquid. The residual gas was led into a fume cupboard for ventilation to the atmosphere. The furnace used for visual observations of needle growth and other phenomena consisted of a transparent silica reaction tube of bore 3 cm, having an optically flat silica window sealed into its wall. The reaction tube was clamped vertically, inside a mullite tube of bore 4 cm and length 42 cm which was heated by Kanthal windings. The window in the silica reaction tube was arranged opposite a hole 3 cm wide and 2 cm tall which had been cut in the wall of the mullite winding tube 19 cm from its top end. A binocular microscope was used to look through the window, illumination being provided by a focusing microscope-lamp offset sideways and downwards. The oxide block to be sulfated was suspended from the removable Pyrex top-piece to the reaction tube, by means of which it was inserted at the start of the experiment, and through which entered the S02/02 gas mixture. The variation of the temperature inside the reaction tube with horizontal and vertical displacement from the window was investigated, and, while it can be said that the temperature was constant 1 deg, its value at a given position was known only to 12 deg. In both furnaces, the oxide block to be sulfated was suspended from a small silica hook immediately downstream from a platinum thimble used as catalyst, which was held on a long silica rod from a Pyrex spring attached to the removable Pyrex top-piece of the furnace. The spring was only included in the quantitative sulfating furnace; its sensitivity was 1.4 cm per g and it was found to be free from creep in a 16-hr test when carrying the working load. The extensions were followed by a cathetometer which could be read to 0.001 cm, corresponding to i0.7 mg. Extensions of the spring were measured on adding weights between 5 and 500 mg to the working load (thimble + oxide block), and Hooke's law was closely obeyed. SAMPLES Cuprous oxide blocks were prepared by oxidizing Johnson Matthey "Specpure" copper sheet of 1 mm thickness (impurities: iron at 3 ppm, silver at 2 ppm, lead, nickel, sodium, and silicon each at 1 ppm, calcium, chromium, magnesium, and manganese each at less than 1 ppm) for 6 days in air at 1000°C in a re-crystallized alumina boat. It has been reported7 that when Cu20 is prepared by heating copper sheet for 1 day the central plane of the blocks produced consists

Jan 1, 1967

By Robert T. Howard, Morris Cohen

THE purpose of this paper is to direct attention to the lower part of the austenite transformation diagram, or TTT curves, where considerable uncertainty still exists as to the blending of the bainite and martensite reactions. The dissimilarities between these two low temperature trans- formations have been summarized recently by Troiano and Greninger.1 Of particular importance to the present work is the fact that martensite formation, unlike bainite formation, is not suppressed by the fastest quenching rates attainable. However, most of the investigations in this direction have been concerned primarily with the start of the martensite transformation [(M,)] during cooling, rather than with the quantitative aspects of the subsequent reaction on either further cooling or isothermal holding. Several years ago, Cohen2 suggested a form of transformation diagram which reconciled, at least schematically, the isothermal characteristics of the bainite transformation with the insuppressible nature of the martensite transfoi mation. In essence, the diagram consisted of a family of horizontal lines (representing the progress of the austenite-martensite reaction during quenching) which were interrupted in point of time by the bainite family of C-curves extending down from higher temperatures. This picture received later support by metallographic3 and dilatmetric4,5 studies, but the techniques employed were not sufficiently critical to substantiate some of the details. Elmendorf6 and Grange and Steward7 have shown that the Greninger-Troiano metallographic techniques may be used not only for [M,] determinations, but for studying the course of further austenite decomposition. In fact, the latter investigators have observed the amount of martensite formed as a function of temperature below [M,] in fourteen commercial steels. In the present paper, the Greninger- Troiano technique has been combined with the lineal method of Howard and Cohen9 to provide a unique, quantitative treatment of the austenite-martensite reaction. Furthermore, isothermal transformations have been similarly measured on holding at temperatures above and below M,, thus permitting a fairly detailed presentation of the lower part of the conventional austenite transformation diagram. EXPERIMENTAL DETAILS Materials The steels, listed in Table I, were selected for study because they exhibit a satisfactory range of M, temperatures and have not received as much attention as the lower carbon grades. They were prepared as 30 lb induction furnace heats in the laboratories of the Vanadium-Alloys

Jan 1, 1947

By Joseph Jensen

CURTAILMENT of oil production in California began in 1922 and 1923 when certain of the major companies completely shut down some pumping properties. Efforts of this kind were generally carried on without coordination by individual companies until 1923. From May to August of 1923, oil production in the Los Angeles Basin was curtailed because of lack of pipe-line outlets. This work was handled by a small committee of executives and engineers of some of the pipeline companies without any established. Method such as obtains at present. Not all of the major companies participated in ibis curtailment and the effort was not well organized. The problem then was principally to move the oil. The crisis passed in September of 1923 from then on the major companies each on it own initiative, shut in additional production. At Domiuguez, in 1921, Shell, Union and Associated agreed to limit drilling to a 100-ft. zone for one Near. In the summer of 1925, operators at Ingde-wood agreed to limit developments to a 1300-ft. zone during the 1925 drilling campaign. In the summer of 1927, the Ventura operators cut back their production one-third and deft it thus for 90 day. Drilling in this field has always been at a slow and conservative rate.

Jan 1, 1932

By R. W. Raymond

ChaRles William HenRy Kirchhoff was born March 28, 1853, at San Francisco, Cal., where his father, Charles Kirchhoff, was at that time consul for his native country, Germany. A few years later, the family moved' to Hoboken, K. J., in which city the son received his preliminary education at the Hoboken Academy, proceeding later to Germany, where he was graduated in 1874 as mining engineer and metallurgist at the Prussian Royal Mining Academy of Clausthal, in the Harz. Upon his return to the United States, he became chemist of the Delaware Lead Refinery at Philadelphia, and retained that position for three years. But in 1877 he began what was to be an almost uninterrupted life-long association with David Williams, the publisher of The Iron Age, of New York, who established in that year, and continued for a brief period, a journal entitled the Metallurgical Review, on the editorial staff of which Mr. Kirchhoff received a place. The enterprise was doubtless an attempt to cover a wide metallurgical field outside of that which properly belonged to The Iron Age. But it was soon abandoned, and Mr. Williams wisely concentrated his energies upon the older journal, which, under his vigorous and skillful management, and the labors of the able editors and correspondents whom he selected, became one of the greatest institutions of its class in the world. From 1878 to 1881, Mr. Kirchhoff was assistant editor of The Iron Age. From 1881 to 1884, he was managing editor of the Engineering and Mining Journal; in 1884 he returned to The Iron Age, to become for five years its associate editor, and in 1889, on the retirement of James C. Bayles, editor-in-chief. This list of dates and employments, without further comment, sufficiently indicates, at least to the eye of an expert, that Mr. Kirchhoff had found his congenial career in trade journalism. His qualifications for this profession were somewhat exceptional. He possessed the scientific training, the knowledge of foreign languages and literatures, and the power of making and keeping friends, which enabled him to get early notice of technical novelties; he had the taste for statistics which made him both industrious and intelligent in their collection and use; and to these traits he added a mastery of the meaning of such accumulated data, and a sane, critical judgment of the situations which they represented, as well as of the sources and the figures themselves, which made his opinion weighty

Jan 1, 1917

By R. W. Gurry

IN the course of a series of measurements of the rate of diffusion of carbon in austenite at about 960°C. (1760°F.) and 1110°C. (2030°F.), it became necessary to determine carbon concentration when austenite is saturated with graphite, because of indications that the hitherto accepted value of the solubility of graphite in this temperature range is too low. Specimens of carbonyl iron were saturated at temperature in a hydrogen-toluene atmosphere which was in equilibrium with graphite. The carbon content of the steel was measured either by combustion or by the loss of weight after substantially complete decarburization in an atmosphere of hydrogen saturated at room temperature with water vapor. The absence of carbide or graphite as a phase at temperature was demonstrated by microscopic examination of saturated specimens that had been drastically quenched. The mean result of concordant measurements is that gamma iron saturated with respect to graphite contains 1.39 per cent carbon at 957°C. (1755°F.) and 1.89 per cent at 1110°C. (2030°F.). These two values, plotted along with what appears from the literature to be the best value (0.69 per cent) at the iron-graphite eutectoid temperature (738°C. or 1360°F.), yield a curve that is almost linear, and which, continued upward through a short interval, leads to a limiting solubility of 1.98 per cent at the iron-graphite eutectic temperature 1135°C. (2075°F.) instead of the commonly accepted value of about 1.7 per cent. EXPERIMENTAL PROCEDURE The samples of carbonyl iron, with the exception of those for microscopic examination, were cylinders 3.8 cm. long, 0.475 cm. in diameter. They were placed in a graphite holder and suspended in a vertical furnace, the temperature of which was controlled precisely by means of the resistance of the platinum winding.1 In the empty furnace the range of temperature over a distance of 4 cm. at the heat center was 9°C. (16°F.) but at a given location the temperature remained within ±0.5°C. (0.9°F.); it was measured by inserting a platinum-rhodium couple calibrated at the melting point of palladium, 1555°C. Since the presence of the sample probably improved the uniformity of temperature, it was decided to consider the average temperature of the sample to be 3°C. lower than the maximum measured in the empty furnace with the same setting of the controller. Data were obtained in the vicinity of two temperatures, 960°C. (1760°F.) and 1110°C. (2030°F.). The samples for microscopic examination, 2.2 cm. long, 0.475 cm. in diameter, were suspended individually on pure iron wire; for these no temperature correction was applied. The carburizing gas passed into the furnace was dry, oxygen-free hydrogen saturated at room temperature with

Jan 1, 1942

By D. K. Crampton

Internal stress and season cracking in brass have been studied for many years and the technical literature contains many data on various phases of the subject. A resume of the literature shows certain fairly well established points upon which various authors are mostly agreed: 1. Season cracking is primarily caused by the presence of relatively high internal stresses, or possibly in some cases by external stresses, or both. 2. A specific corrosion is also essential to season cracking. Certain agents, particularly mercurous salts, mercuric salts and ammonia salts, have such a specific corrosive effect. 3. The tendency to season crack under given conditions increases with increasing zinc content, brass containing less than 20 per cent. zinc being relatively immune. 4. In alpha brass the season cracks are intercrystalline; in alpha-beta brass they lie between the two constituents; and in beta brass they are transcrystalline. 5. The ordinary impurities or added elements in special brasses have little or no effect on the tendency to season crack. 6. Internal stresses can be eliminated, or at least reduced to a safe limit by annealing treatments at temperatures that do not produce visible microstructural changes or appreciable softening of the worked brasses. There are, however, some points in connection with the phenomenon of season cracking which have not been thoroughly investigated, or wherein different authors and investigators are not entirely in agreement. The investigations described in this paper were undertaken to determine: 1. The correlation between mercurous nitrate tests and actual season cracking on long-time atmospheric exposure. 2. The quantitative effect of type and degree of drawing operations on the intensity of internal stress and on the tendency to season crack in brass tubes. 3. The possibility of drawing high-brass tubes in such a manner as to prevent the occurrence of harmful stresses rather than to find a remedy for such stresses once having obtained them.

Jan 1, 1930

By Y. G. Shiau, J. E. Burke

Several attempts have been made to account for the fact that grains in a fully recrystallized metal will coarsen on annealmg. Two fundamentally different hypotheses have been advanced, with several variations of each. One school considers that the cause of grain growth is the surface energy of the grain boundary. The theory of Jeffriesl that grain size and grain size contrast control growth is an example. The second school considers the primary cause to be a difference in the lattice energy on either side of the grain boundary. The more perfect grains are considered to grow at the expense of their less perfect neighbors, with a decrease in free energy, and a consequent increase in the stability of the system. Burgers2 presents the case for the strain or lattice imperfection theory of grain growth quite completely. The latter theory is attractive, since there is no doubt that differences in lattice energy or lattice perfection can cause grain boundary migration. A recrystallization nucleus grows for this reason as was beautifully demonstrated by van Arkel and Ploos van Amstel.³ Although it is generally stated that grain growth does not precede recrystallization, several workers4-5 have shown that small strains may induce a single crystal in an aggregate to grow, or at least may cause some grain boundary migration. The origin and nature of the imperfections that are considered to be responsible for normal grain growth have never been clearly described, but it is generally agreed that they are a consequence of the difficulty of atomic reorientation in the solid state, and that they do not seriously differ from the type of imperfection that can be introduced by mechanical deformation. An object of the present work was to determine whether the introduction of mechanical deformation would cause grain growth in a specimen which would not otherwise show it under the conditions used. It was also planned to determine the effect of such deformation on the rate of growth in a specimen which would show growth in the unstrained condition. Recently Maddigan and Blank6 have indicated that slightly strained specimens of alpha brass can undergo considerable growth prior to recrystallization if annealed at low temperatures. French7 has reported that at deformations less than 17 pet it is very difficult to detect the beginning of recrystallization in the same material. It was therefore planned to broaden this work to include a complete study of the microscopic behavior of alpha brass under condition~ of temperature, time, grain size and deformation such that recrystallization would not occur or would occur to only a Small extent. Experimental Procedure The brass was prepared by melting cathode copper and commercially pure zinc

Jan 1, 1949

By J. E. Burke, Y. G. Shiau

Several attempts have been made to account for the fact that grains in a fully recrystallized metal will coarsen on annealmg. Two fundamentally different hypotheses have been advanced, with several variations of each. One school considers that the cause of grain growth is the surface energy of the grain boundary. The theory of Jeffriesl that grain size and grain size contrast control growth is an example. The second school considers the primary cause to be a difference in the lattice energy on either side of the grain boundary. The more perfect grains are considered to grow at the expense of their less perfect neighbors, with a decrease in free energy, and a consequent increase in the stability of the system. Burgers2 presents the case for the strain or lattice imperfection theory of grain growth quite completely. The latter theory is attractive, since there is no doubt that differences in lattice energy or lattice perfection can cause grain boundary migration. A recrystallization nucleus grows for this reason as was beautifully demonstrated by van Arkel and Ploos van Amstel.³ Although it is generally stated that grain growth does not precede recrystallization, several workers4-5 have shown that small strains may induce a single crystal in an aggregate to grow, or at least may cause some grain boundary migration. The origin and nature of the imperfections that are considered to be responsible for normal grain growth have never been clearly described, but it is generally agreed that they are a consequence of the difficulty of atomic reorientation in the solid state, and that they do not seriously differ from the type of imperfection that can be introduced by mechanical deformation. An object of the present work was to determine whether the introduction of mechanical deformation would cause grain growth in a specimen which would not otherwise show it under the conditions used. It was also planned to determine the effect of such deformation on the rate of growth in a specimen which would show growth in the unstrained condition. Recently Maddigan and Blank6 have indicated that slightly strained specimens of alpha brass can undergo considerable growth prior to recrystallization if annealed at low temperatures. French7 has reported that at deformations less than 17 pet it is very difficult to detect the beginning of recrystallization in the same material. It was therefore planned to broaden this work to include a complete study of the microscopic behavior of alpha brass under condition~ of temperature, time, grain size and deformation such that recrystallization would not occur or would occur to only a Small extent. Experimental Procedure The brass was prepared by melting cathode copper and commercially pure zinc

Jan 1, 1949

By S. N. Kesten, Richard Murphy, A. H. Land, W. F. James

Introduction—by W. F. James and A. H. Lang This paper describes the geology and present state of development of uranium and thorium deposits in Canada. It is expected that this information will be added to that now being assembled from available American and British data to provide a background for engineers and others who may be called upon in the future to examine or search for radioactive deposits. Some generaliza- tions regarding the Canadian deposits are included, but many of these are necessarily tentative. The information contained in the paper is up to date for the end of 1948. The information contained in this paper has been derived from many sources. Much of it is from the records of the Canadian government-owned Eldorado Mining and Refining (1944) Limited and from examinations of government and private properties made by officers of the Geological Survey of Canada. Some information on privately-owned properties has been quoted from other sources mentioned in the text. The information has been assembled by W. F. James of Eldorado Mining and Refining (1944) Limited and A. H. Lang of the Geological Survey of Canada, who have written the sections for which they are credited. The description of the Eldorado mine is based on reports by Richard Murphy, formerly chief geologist for Eldorado; the report by Mr. Murphy was published previously by the Canadian Institute of Mining and Metallurgy,' to whom the writers are indebted for permission to repub-lish. The section dealing with the geology of and development work in the Goldfields area, where Eldorado has important holdings, is by S. N. Kesten, field geologist for Eldorado. The geological diagram of the Goldfields area (fig. 2) was kindly supplied by A. M. Christie of the Geological Survey of Can-

Jan 1, 1951

By W. F. James, Richard Murphy, S. N. Kesten, A. H. Land

Introduction—by W. F. James and A. H. Lang This paper describes the geology and present state of development of uranium and thorium deposits in Canada. It is expected that this information will be added to that now being assembled from available American and British data to provide a background for engineers and others who may be called upon in the future to examine or search for radioactive deposits. Some generaliza- tions regarding the Canadian deposits are included, but many of these are necessarily tentative. The information contained in the paper is up to date for the end of 1948. The information contained in this paper has been derived from many sources. Much of it is from the records of the Canadian government-owned Eldorado Mining and Refining (1944) Limited and from examinations of government and private properties made by officers of the Geological Survey of Canada. Some information on privately-owned properties has been quoted from other sources mentioned in the text. The information has been assembled by W. F. James of Eldorado Mining and Refining (1944) Limited and A. H. Lang of the Geological Survey of Canada, who have written the sections for which they are credited. The description of the Eldorado mine is based on reports by Richard Murphy, formerly chief geologist for Eldorado; the report by Mr. Murphy was published previously by the Canadian Institute of Mining and Metallurgy,' to whom the writers are indebted for permission to repub-lish. The section dealing with the geology of and development work in the Goldfields area, where Eldorado has important holdings, is by S. N. Kesten, field geologist for Eldorado. The geological diagram of the Goldfields area (fig. 2) was kindly supplied by A. M. Christie of the Geological Survey of Can-

Jan 1, 1951

By Adrien Berton

FOR nearly a century, the Corocoro deposit has been renowned among geologists from the fact that it shares with the Lake Superior deposits of the United States the distinction of being the only important copper districts where native copper is worked commercially. The Corocoro district, named after the city of Corocoro, the capital of the Province of Pacajes (Department of La Paz, Bolivia) is situated towards the western edge of the Bolivian high plateau, at an altitude of a little over 13,000 ft. The most interesting part of the district is that immediately surrounding the city of Corocoro, at a distance, by railway, of 65 miles from La Paz and 210 miles to the Chilean port of Arica on the Pacific Coast. The climate of the region is that of the semi-desert, dry and relatively cold, with big differences of temperature between day and night. The rainy season begins in December and ends in March. The cupriferous lodes of Corocoro have not attracted as much interest as the silver mines of Potosi but they have been known for a long time. In the precolonial period the Indians were using the charquis, or natural native copper sheets, to make small brass objects, and the beautiful pale green brochantite of the outcrops as a source of green pigments. During the colonial period, the oxidized ores of the outcrops were worked for copper, which was used by the mint at Potosi for making currency. The native copper ores were neglected because the Spanish miners were at a loss how to concentrate and smelt them. About 1830, work by rudimentary processes, which were improved little by little, was begun on the native copper ores. The total production of native copper in the following hundred years amounted to 100,000 tons. This native copper, which was remarkably pure, was much appreciated on the European markets before the introduction of electrolytic copper. It was useful for making special ornamental brass or bronze and the granular concentrates of native copper, called barrilla, containing 80 to 85 per cent copper were suitable for making copper sulfate by direct oxidation and subsequent leaching with sulfuric acid.

Jan 1, 1936

By F. E. Bash

Constantan is an alloy of copper and nickel that is extensively used, under a number of trade names, as a resistance wire with a low temperature coefficient of resistance, and one of the elements of base-metal thermocouples, iron usually being the other thermoelement, although for low-temperature work copper is also used. Before the war, constantan was imported, in common with many other technical necessities. Since it required considerable time to receive the constantan after it was ordered, fairly large stocks were kept on hand; but after the beginning of the war no more was imported and the stocks of foreign material were exhausted about the same time that the steel and munition manufacturers began to need great quantities of it for thermocouples for the heat treatment of steel. To meet this demand, the International Nickel Co. began manufacturing constantan that met all the requirements of the users of resistance wire but did not give the same electromotive force against iron as the German material and consequently could not be used with instruments calibrated for a definite e.m.f.-temperature relation. It so happened that all the constantan made had an e.m.f. lower than that necessary to meet the specifications of the Leeds & Northrup Co. for whom this investigation was carried out. If some had been higher and some lower, good wire could have been obtained by a process of selection, but as it was no wire at all could be procured. To remedy this situation, a thorough investigation was started with the close cooperation of the International Nickel Co. and the Electrical Alloys Co. The specifications to which the constantan had to conform were that it should give an e.m.f. of 47.40 millivolts against pure iron at 1500" F. (816" C.) with the cold-junction temperature at 0" F., or a proportional e.m.f. at temperatures near 1500" F. The method of checking a wire was as follows: It was first welded to a piece of iron wire; Armco iron was found to be satisfactory but iron with greater than 0.1 per cent. carbon would give a lower e.m.f. against the same piece of constantan than pure iron. The couple was then insulated and the fire end was tied to the

Jan 1, 1921

By Hans Lundberg

IN ORDER to comprehend the help and information that may be expected from electrical prospecting, it is necessary to have at least a general knowledge of the methods and principles involved in preparing and interpreting results obtained in the field. Electrical prospecting is rather complicated, both in theory and practice, and in order to make a brief description clear to the practical mining man it has been necessary to idealize and generalize the problems, at the risk of having such simplification criticized by the theoretical man. This simplification must not be misinterpreted as showing a lack of theoretical knowledge. FIG. 1.-FLOW OF CURRENT IN AND AROUND A CONDUCTING BODY. For its operation, electrical prospecting mainly depends on-the fact that most metallic ores conduct an electric current much more readily than barren rocks. If an electric current flows through a block of ground within which a body of chalcopyrite is enclosed in country rock of schist, the current will find less resistance to its passage through the chalcopyrite than through the schist, even though the passage through the latter be much shorter. This is because the longer path through the chalcopyrite offers less resistance, owing to the superior electrical conductivity of the chalcopyrite (Fig. 1).

Jan 1, 1928