Search Documents

By M. J. Marcinkowski, A. Szirmae, R. M. Fisher

Room -temperature hardness measurements obtained from single and polycrystalline samples of a 47.8 at, pet Cr-Fe alloy which were aged for various times al 500°C show a two-fold increase over that of the unaged alloy after annealing for 1000 hr. A detailed examination of the deformation markings in the neighborhood of the hardness imbressions reveals that twinning becomes an increasingly more important mode of deformation as aging proceeds. this observation is shown to be inconsistent with the Proposals that the transformation is eve of order-disorder On the other hand, the results are in agreement with previous observations of Fisher et al. of a coherent chromium-rich precipitate which forms in an iron-rich matrix as a result of a miscibility gap in this alloy system as proposed by Williams . Using the coherent precipitate hypotlzesis as a model, a detailed analysis of the various possible strengthening contributions to both the slip mid twinning stresses is made. In the case of' slip, lattice friction within the chromium-rich phase and the chemical energy associated with the interface between the two phases contribute about 60pet to the total strength. The contributions from coherency strains and modulus differences are thought to contribute the remaining 40 pet of the strength but are difficult to evaluate because of uncertainties regarding the flexibility of the dislocation line. All of the factors have nearly the same or else a smaller effect on the twinning stress in the aged alloy. Twinning is never observed in the unaged alloy because the twinning stress is much higher- than that for slip. With increased aging times, the various contributions to the total stress for both twinning and slip increase, but most of those for slip increase much more rapidly, so that, in the fully aged alloy, it surpasses the stress for twin propagation. When a twin is nucleated by the chance occurrence of an internal stress concentration during a test, the subsequent twin burst results in a low hardness reading. FeRNTIC Fe-Cr alloys from about 15 to 80 at. pet Cr content show considerable change in properties such as hardness, electrical resistivity, saturation magnetization, and so forth, after aging in the vicinity of 500°C.* The most marked change is a large increase in hardness accompanied by a sharp decrease in ductility, so the phenomenon has often been referred to as the 475°C (885°F) em-brittlement problem. Changes in microstructure are rather subtle and most investigators have not been able to observe any X-ray diffraction or metal-lographic changes during aging. There is little doubt that the phenomenon is inherent to the Fe-Cr binary system and is not directly related to the formation of a phase. Two distinct schools of thought have developed during the past decade concerning this problem. Masumoto, Saito, and sugiharal have concluded, from their own specific-heat measurements, that atomic ordering occurs in this temperature range. Pomey and Bastien2 have also attributed the changes in physical properties with aging in the neighborhood of 500°C to atomic ordering. In addition, Takeda and Nagai3 claimed to have found X-ray verification for superlattices corresponding to the compositions FesCr, FeCr, and FeCr3. However, all known attempts to observe superlattices in Fe-Cr alloys using neutron diffraction, which should be much more sensitive, have been unsuccessful. These have been reported by Shull et al.4 for 25 at. pet Cr, williams5 for 75 at. pet Cr, and Tisinai and samans6 for a 28.5 at. pet Cr. steel. The second and more prevalent opinion ascribes the 475°C embrittlement phenomenon to the formation of a coherent precipitate due to the occurrence of a miscibility gap in the Fe-Cr system below about 550°C. This latter concept was first indicated by the results of Fisher, Dulis, and Carroll,7 who were able to extract fine particles about 200Å in diameter from samples of 28.5 at. pet Cr steels aged from 1 to 3 years at 475°C. The extracted material was found to be nonmagnetic, to have a bee structure with a lattice parameter between that of iron and chromium, and to contain about 80 at. pet Cr. Williams and paxton8 and williams5 confirmed these results and first explicitly proposed the existence of a miscibility gap below the a region in the equilibrium diagram. Alloys aged within this gap

Jan 1, 1964

By R. J. Fruehan

The oxygen activity and concentration were measured in Fe-Cr-0 melts in equilibrium with an oxide phase at 1600°C (2912°F). The activity was determined by ,use of the following solid oxide -electrolyte galvanic cell CY-Cr8,(s) I ZrOz(CaO) I Fe-CY-G(saturated)(l) The oxygen concentration decreases with increasing Cr concentration to about 270 ppm 0 at about 7pct CY and then increases gradually. The activity coefficient of oxygen (fo) decreases with increasing Cr. In melts containing up to about 20 pct Cr, log f is approximately a linear function of wt pct Cr with a slope (e q 2) of —0.037. The activity of chromium was calculated and found to exhibit a small negative deviation from Raoult's law. From the activity and solubility data for low chromium melts, the free energy of formation of chromite, FeCr204, was found to be -79.8kcal per mole where pure liquid chromium and oxygen at I wt pct in Fe are the standard states. ThE effect of chromium on the chemical behavior of dissolved oxygen in liquid iron is of great importance in controlling the deoxidation of steels containing a significant amount of chromium. Chen and chipman' equilibrated Fe-Cr melts in the presence and absence of slag with hydrogen-water vapor mixtures. They concluded that at 1595°C chromite was the oxide phase in equilibrium with Fe-Cr alloys containing less than 5.5 pct Cr while at higher chromium concentration Cr,O, was the stable phase. In the composition range 0 to 10 pct Cr they found that the interaction coefficient, was equal to -0.041. Turk-dogan,' Schenck and Steinmetz,, and pargeter4 measured egr) in a similar manner and found the value to be -0.064,-0.04, and -0.052, respectively. McLean and Be11 evaluated egr) from their data on the equilibrium of Fe-Cr-Al-0 alloys with H2/H20 mixtures and found it to be -0.058. However, McLean and Bell's value should only be considered an estimate because the effect of aluminum on the activity coefficient of oxygen is about a hundred times greater than that of chromium. Consequently, an error in the value of egl) used, which at the present time is not well-known, or an error in aluminum analysis, which is present in very small quantities, will result in a significant error in egr). Fischer et a1.6 determined the interaction coefficient (eEr) in Fe-Cr-0 melts not in equilibrium with an oxide phase and containing less than 18 wt pct Cr at 1600°C electrochemically. They determined a value of -0.031 for egr). Hilty et aL7 measured the oxygen content of Fe-Cr melts in equilibrium with an oxide phase containing up to 50 pct Cr. They found that the solubility of oxygen decreased as the chromium content increased to about 6 pct Cr and then increased gradually. They concluded that the equilibrium oxide phase was chromite below 3 pct Cr, distorted spinel from 3 to 9 pct Cr, and Cr,04 above 9 pct Cr. Adachi and lwamotoa also investigated this system, but did not find Cr30,. They X-rayed the equilibrium oxide phases and did not find the presence of Cr,O,. They also X-rayed the oxide phase extracted from a 65 pct Cr melt which was heat treated and did not find metallic chromium as would be expected if Cr3O4 were the equilibrium oxide phase as indicated by the reaction : 3Cr3O4 — 4Cr2O:, + Cr [lj It was the purpose of the present investigation to determine the effect of chromium on the activity coefficient of oxygen in Fe-Cr melts by measuring the activity and solubility of oxygen equilibrated with an oxide phase in the composition range 0.18 to 50.5 wt pct Cr at 1600°C (2912°F). The activity of oxygen in the melts was determined by use of the following galvanic cell: The relationship between the partial pressure of oxygen in equilibrium with the melt and the reversible electromotive force of the cell (E) is where 11 = 4, F is the Faraday constant, pb, is the oxygen pressure in equilibrium with the meit and is the oxygen pressure in equilibrium with Cr203 as determined from the free energy data compiled by Elliott et al? The oxide phase in equilibrium with pure chromium was assumed to be Cr If Cr30, were the equilibrium phase the activities derived would be approximately the same, since the best estimated free energy of formation of Cr,O,, if it does exist, is approximately % the free energy of formation of The activity of chromium in Fe-Cr alloys at 1600° C was also determined from the measured electromotive force. The activity of chromium (aCr) is related to the electromotive force as follows: , The oxide phase in equilibrium with pure chromium and Fe-Cr melts from 10 to 52 pct is assumed to be Cr203 so that n equals three. If future work proves the existence of Crs04 in equilibrium with Fe-Cr melts and pure chromium, the experimental results can be reevaluated using a value of $ for n in Eq. 141. A value of ^ for n will make the activities about 10 pct higher. In order for Eqs. 131 and [4J to be valid the electrolyte, ZrOa(CaO), must exhibit predominantly ionic conduction at the temperature and oxygen partial pressure of its use. Previous work1' has demonstrated that ZrOz(Ca0) is predonlinantly an ionic conductor

Jan 1, 1970

By O. B. Ellis

Although thousands of tons of stainless steel have been used successfully for many types of equipment, there have been few cases of failures due to the phenomenon described as stress corrosion cracking. During the past seven years only six cases of such failures have been drawn to our attention and investigated in the Research Laboratories with which the author is associated. These failures oc¬curred in two coffee urns, two wool con¬ditioning units, one dyeing machine, and another in a part of a steam-jacketed stock pot. In each case the equipment failed in a comparatively short time after exposure to conditions of high humidity at tempera¬tures in the range of 100 to 200 F. The failures in all cases were characterized by general embrittlement and cracking of the stainless steel, with only slight indications of general corrosion except at the cracks. The first failure of this type was a coffee urn returned for investigation in 1937. The top and bottom sections showed a general corrosive attack and embrittlement and cracking of the stainless steel. The chemical analyses of these sections were as follows:

Jan 1, 1945

By Woolf, W. G.

Filtration of hot (60°C) supersaturated zinc sulphate solution (sp gr 1.540) from slimy leach residues at the electrolytic zinc plant of Sullivan Mining Co., Kellogg, Idaho, is de- scribed. Separation of liquids and solids in the finished leach is by Burt filters modified to meet conditions of high-acid, high-density process for electrolytic zinc. Operating characteristics of the Burt filter on this pulp are presented.

Jan 1, 1950

By M. R. Geer, H. F. Yancey

With the exception of pneumatic processes and a few special beneficiation methods of comparatively limited application, all mechanical coal-cleaning and mineral-dressing processes involve the admixture of solid particles with a liquid, generally water. Upon completion of the beneficia-tion process the solids must be reclaimed from the water. With coarse particles separation of solids from water is accomplished readily by the simple expedient of screening, but recovery of fine solids presents a much more difficult problem. Thickening and dewatering are practiced so generally, both within the mineral industry and elsewhere, that they have been the subject of study through the years and a number of processes for making the solid-liquid separation have been developed. Dorr-type thickeners have been standard equipment lor many years, and more recently driers employing centrifugal force have gained in popularity.' A cyclone device employed to thicken the loess suspension is a novel feature of the loess heavy-medium coal-cleaning process developed by the Netherlands State Mines in the thirties. The cyclone thickener was first mentioned by Driessen2 in 1939 in a paper describing the loess process and has been the subject of two more recent reports by the same author.3 The cyclone does not differ greatly from cyclone dust collectors used in this country for years, except that it is operated wet rather than dry. Advantages of the cyclone over other thickening devices are its simplicity of construction, high capacity, and the fact that, having no moving parts, it is simple and inexpensive to operate. The Bureau of Mines became interested in the cyclone after one of the present authors observed it in operation in the Netherlands in 1945. The first experimental work with the cyclone conducted by the Bureau of Mines was an investigation of the unit functioning as a heavy-medium cleaner for fine coal—a use for the cyclone that was conceived long after it had been perfected as a thickener. The results of this investigation were published last year.4 The present investigation deals exclusively with operation of the cyclone as a thickener. Object and Scope of Investigation Although the cyclone thickener has been dealt with in three reports by Driessen, its use as a thickener was not the principal subject of any of these reports and therefore neither the cyclone itself nor its operation was described completely. The design of the cyclone was described only in a very general way, only limited operating results were given, and virtually nothing was disclosed about the influence of the various possible operating variables. Moreover, the Netherlanders apparently had employed the cyclone exclusively for thickening loess and had not employed it On coal 'lurries. One English colliery has used a cyclone to thicken coal slurry,5 and as it appeared that

Jan 1, 1949

By A. Blake Caldwell

Tyrone-a complete mining and concentrating facility built by Phelps Dodge Corp.-straddles the Continental Divide where surface water on either side flows in opposite directions although all water is taken from and returned on the northwest side of the Divide. At the outset, Tyrone was saddled with a problem of an adequate water supply, and the Gila River some 23 miles distant appeared to be the logical source. This in itself presented a major obstacle to Phelps Dodge because of the distance water had to be pumped and because of an adverse head which had to be overcome between the Gila River and the two 4-million-gal-capacity terminal water supply tanks at the mill. Having acquired water rights on the Gila River and in order to control the seasonal fluctuations in water volume, the company built the Bill Evans, off stream, earth-filled dam. This reservoir will contain 2100 acre-ft of water when full and it was constructed by the Hamilton Construction Co. for Phelps Dodge. The dam impounds fresh water for the Tyrone plant's use and four vertical turbine pumps (4500 gpm each) lift the water 275 ft from the Gila River into the reservoir. Since construction, Phelps Dodge has optioned the lake to the New Mexico State Game Commission for recreational purposes. In addition to the lake, land around the reservoir has been optioned to the State Game Commission for public use. The lake has already been stocked with trout and by next summer some keepers should be available for the taking.

Jan 12, 1969

By J. Ruzicka

IN creep testing, material is subjected to a constant load, preferably at a constant temperature, and its rate of deformation is measured. The method of loading can be of various types but in this paper only creep testing under tensile load will be considered. The ordinary tensile test is essentially a comparison test in conditions that frequently bear little or no relation to those under which the test material is to be used in service. The purpose of creep tests is to measure the strength of the test material at slow rates of deformation that more nearly approach the rates realized in service. One purpose of this paper is to illustrate that the creep test, in addi-tion to its value as a service test, is superior to the ordinary tensile test as a sensitive tool for the comparison of certain metals in investigative testing. The other purpose is to describe equipment having distinctive features of design that make it especially suitable for such tests. Representative data obtained with this equipment on a group of rolled zinc-base materials are given. These data are compared with those from practical comparison tests of the creep type on weatherstrip fabri-cated from the same group of materials. The comparison illustrates the value of the fast creep test and of the equipment.

Jan 1, 1937

By Ottey M. Bishop, William G. Peryam, Fred E. Johnson

THE Lepanto Consolidated Mining Company is the largest copper producer in the Philippines, and the only one that makes a concentrate valuable principally for its copper; also, it has the only productive copper mine situated at considerable distance from the sea, and is the only one in the islands operating its own smelter. The Lepanto mine is in the Municipal District of Mankayan, sub-province of Benguet, near the heart of the Mountain Province of Northern Luzon. It is 165 km. from its shipping point at San Fernando, Province of La Union, on the shore of the China Sea. Elevations at the property range from 3200 to 4500 ft. The climate is very mild; temperatures are seldom below 50° or above 80°F. Annual rainfall approaches 170 in. and is mainly confined to a rainy season lasting from May to October. The months from December to April, inclusive, are usually extremely dry. This climatic pecularity entails the problems of landslides on the roads during the rainy season and water shortage during the dry season. The Mountain Trail, an improved rocksurfaced toll road maintained by the Commonwealth Government, gives access to the property. The 105 km. over this road may be traveled in about 4 ½ hr. during the dry season. Very few sections of the road are straight for more than 100 meters, and about one third of it is a one-way road controlled by gates. All freight for the property is delivered by the Manila Railroad Company to Bauang, La Union, 45 km. west of Baguio and at sea level, where it is picked up by freight trucks and hauled via Baguio to Lepanto. Granulated matte is hauled in bulk from Lepanto in four-ton lots on freight trucks to the storage bins at San Fernando. Freight rates from Bauang to the property amount to [P]8.oo per ton, and from the property to San Fernando the rate is [P]16.00 per ton. The company pays the road toll, [P] 1.00 per truck, each way. THE CAMP The company maintains a modern camp, well separated from the mine and reduction plant. Comfortable and sanitary living quarters, water, and light, as well as free medical service are provided all employees. A hospital staffed by a doctor and two nurses takes care of all medical treatment. Considering recreational facilities of great importance, the company has provided two tennis courts, two basketball courts, and badminton courts for employees. Bowling alleys and a motion picture theater are operated by the company, the profits being expended for other recreational purposes. A moderate sized recreation hall serves for barrio dances, meetings,

Jan 1, 1942

By John R. Lotz

DEVELOPMENTS in Iran currently arousing interest in a considerable portion of the world, particularly on the part. of that country's immediate neighbor on the North and in our own country, an inseparably related to and largely dependent upon the government's attempts to strengthen its economy and improve the standard of living of its people. These efforts are encompassed by provisions of the Seven-Year Development Plan recently enacted and not, in the process of implementation. It is a fine example of what one financially sound but extremely backward and poorly equipped country has undertaken to do on its own account and with its own resources. This Seven-Year Plnil was formally authoriztld by an act of the Iranian Parliament in February 1948. Its stated objects are to carry out such plans for the development of the country and its economy as ail1 raise the standard of livinc: and standard of education of the people, and re- duce the cost of living. A seven-yrar program for carrying out the work within the limits of appropriations was assigned under the law. The total amount to be expended during the seven- year period was fixed at the equivalent of $670 millioil at current rates of exchange.

Jan 1, 1950

By Kenneth Seaver

(San Francisco Meeting, September, 1915) INTRODUCTION IT is rather gratifying that in the field of the manufacture 'of refractories, in which, as a whole, foreign practice has surpassed us, the United States stands pre-eminent in the making of silica brick. In some instances European manufacturers have refused point-blank to credit the possibility of making to such specifications as are common with us, until the actual 'completed shapes were shipped for inspection. But both the manufacturer and consumer in foreign lands are now frankly learning from us, and benefiting by our advanced practice in this field, as is evidenced by the orders placed here and the efforts put forth abroad to come up to the standard of American-made material. In no metallurgical operation has the employment of silica brick spread with. such leaps and bounds as in the building of plants for the carbonization of coal, particularly in the byproduct coke oven. Today, in practically all types of oven, the structure above the floor level (except the facings) is of silica, while in the recuperative and in some regenerative types, its use is extended to that portion of the oven below the floor as well. By reason of the fact that there are a number of classes of refractories of higher silica content than the usual so-called fire-clay brick, there is sometimes a misunderstanding as to the class of material referred to as "silica" brick. We here refer only to a brick having a silica content of 94 per cent. or more and made usually from quartzite rock with a small percentage of lime as a binder. The term "silica" brick is sometimes rather loosely applied to brick front highly siliceous clays, or to a quartzite refractory of mingled fire-clay and quartz rock; but such products are not considered in this discussion.

Jan 9, 1915

By A. M. Turkalo

IT is a well-known fact that martensitic steels show a greater resistance to brittle fracture than do pearlitic and bainitic steels. It was, therefore, thought worthwhile to investigate the mode of brittle fracture with respect to structure by studying the effect of various austenite decomposition products on the propagation of brittle fracture in steel by means of electron microscopy. Newly developed replication techniques together with the advantages of the electron microscope such as great depth of field, available high magnification and easy adaptation to stereophotography make electron microscopy very suitable for fracture studies. EXPERIMENTAL PROCEDURE An essentially plain carbon steel containing 0.56 pct C, 1.30 pct Mn, 0.02 pct P, 0.03 pct S and 0.22 pct Si was used in this investigation. The following table gives the heat treatments used to obtain the various austenite decomposition products: The resulting austenite grain size from the 870°C austenitization treatment was about an ASTM No. 7 grain size. The specimens which were 2 in. long, 1/4-in. diam bars were austenitized in a tube furnace through which argon gas was blown. The tube was not, however, air-free and the specimens were not completely oxide-free. Isothermal treatments were done in a lead bath. With the exception of the fully hardened specimen and the one as-isothermally transformed at 300°C the heat treated specimens were notched in the following fashion with a jeweler's saw. A cut about 0.08 in. deep was made perpendicular to the length of the bar. The specimen then was rotated about 45 deg and another cut about 0.08 in. deep was made. In the case of the hard martensitic and bainitic specimens, only one cut was made and the depth was not controlled. The design of the two-cut notch caused fracture to initiate at the point of intersection of the two saw cuts. The specimens were broken at -196°C in a Charpy impact testing machine. In order to hold the specimens securely in the impact machine two square pieces of mild steel were made about 5/8 in. long having the same cross section as that of a standard Charpy specimen but containing a hole 1/4 in. diam through the center of the cross-section. These adapters were slipped over the ends of the test specimen which was then secured tightly by means of set screws in the adapters. The specimen with the adapters was cooled to -196°C in liquid N,, then placed in the impact machine and broken within 3 sec. One half of the broken specimen was used for the electron microscope study of the actual fracture surface. The other half was nickel-plated and a cross section through the notch and fracture was polished for electron microscope examination. Carbon replicas of the fracture specimens for the electron microscope study were made essentially according to Bradley's evaporation technique.' Both direct carbon and two-stage carbon replication techniques were used. In the case of the direct carbon technique, a thin layer of carbon was evaporated first at an angle of about 45 deg to the mean fracture surface and then another film of carbon was evaporated normally to the fracture surface. The carbon replica was freed electrolytically.2 The specimen was made an anode in a 10 pct Nital polishing solution. It was etched intermittently by shutting off the power now and then. The freed replica was washed in 40 to 50 pct water solution of nitric acid for 10 min or so, then washed in water and picked up on a screen for examination. The two-stage carbon replication technique involved first making a primary replica of cellulose * acetate from which a carbon replica was then made. One side of a strip of cellulose acetate wet with acetone was pressed lightly against the surface of the specimen, allowed to dry and then stripped. Prior to the deposition of carbon, which was done at 90 deg to the cellulose acetate replica surface, chromium was evaporated at 45 deg. After the carbon evaporation the cellulose acetate was dissolved in acetone according to the Jaffe method3 leaving the carbon replica preshadowed with chromium for examination.

Jan 1, 1961

By H. LeChatelier, B. Bogitch

Page Introduction........................... 134 Methods of Investigation....................... 135 The Tridymite Network...................... 137 Independent Variables....................... 146 Manufacturing Operations..................... 153 Introduction Silica brick are indispensable in the manufacture of steel because they alone are able to withstand the high temperature of regenerative furnaces. All attempts to replace silica brick by other refractory materials for this purpose have failed, but the reason for this failure has remained obscure; we shall give an explanation later in this paper. Before the war, silica brick employed in France came principally from abroad, for which reason, since the beginning of hostilities, certain French steel works have been seriously handicapped. Our attention was first directed to the question by M. Bied, Engineer of the Teil Works. With him, we began certain investigations, at first using our laboratory and the furnaces of neighboring steel works. The larger part of our experiments, however, have been made in the laboratory of the Faculty of Sciences at the Sorbonne. For the heating of our samples, we are deeply obliged to MM. Charpy, Yeatmann and Guerineau. In undertaking these studies, our first aim has been to render assistance to French industry, by indicating, as precisely as possible, the necessary conditions for the manufacture of high-grade brick; but at the same time me have

Jan 1, 1919

By R. Woods

INTRODUCTION Gaudin (1), considered that "the mechanism of mineral collection is the central problem of flotation theory". From their work on adsorption phenomena in flotation for more than fifty years (2), Gaudin and his co-workers have made major contributions to the elucidation of this mechanism, a fact acknowledged by their contemporaries in the field (e.g. (3)). Their investigations in a number of areas, e. g. demonstrating that submonolayer quantities of adsorbed collector species can induce flotation, or identifying the influence of substances which can activate or depress (1), have helped to provide the basis for and the development of a theory to account for the interaction between mineral and collector. It was established in the late fifties (4) that the presence of oxygen is a prerequisite for the flotation of metal sulfides with thiol collectors. This fact rendered inadequate the concept of simple ion adsorption being responsible for rendering these minerals hydrophobic. The requirement for oxygen has been explained (1) in terms of this species being a component in chemical reactions between the sulfide surface and the collector. Gaudin has been instrumental in identifying the products of chemical reactions at sulfide minerals (1, 5), a line of work which has been continued particularly by Finkelstein and co-workers in South Africa (6). In presenting a detailed mechanism of the mineral-collector- oxygen interaction, it has often been considered that the mineral surface [must] first be oxidized to a metal oxy-sulfur species which

Jan 1, 1976

By Albert Wiggin

THE copper-bearing sulphide ores from the mines in Butte, Mont., which are for the most part concentrated at the Boston & Montana duction Works in Great Falls and at the Washoe Reduction Works in Anaconda, contain the following minerals of economic value: Chalcocite, Cu2S; enargite, Cu3AsS4; cupriferous pyrite; bornite, Cu3FeS3; covellite, CUS; tetrahedrite, 4 CuS2Sb2S3; and tennantite, Cu8AsS7;. All of the ores carry a high percentage of pyrite. Many of the above sulphides are argentiferous and also carry from 10 to 20 cts. per ton in gold. The gangue is quartz and highly altered granite, with sphalerite and galena and more rarely barite and hubnerite as accessory minerals. An average chemical analysis of the second-class ore concentrated at Great Falls and Anaconda would be as follows: Copper 3.2 to 3.4 per cent. Silver 2. 3 to 3.0 oz. per ton. Gold 0.0-1 to 0.15 oz. per ton. Si02.. 55 to 60 per cent. FeO 12 to 15 per cent.. Sulphur 12 to 1.5 per cent. Al2O3, S to 10 per cent. CaO 0.5 to 0.8 percent. As203, 0.5 to 0.6 percent. Lead 0.2 to 0.3 percent. Before describing the Great Falls flow sleet as installed, at Anaconda, a brief history of the Great Falls concentrator will be given, including a description of the various concentrating machines and systems which have been tested in the search for a flow sheet which would give a higher recovery of copper.

Jan 8, 1913

PUBLIC hearings began before the Committee for Reciprocity Information on May 24, 1950, for the purpose of unearthing data and opinion that will be helpful in the forthcoming reciprocal tariff and other trade-barrier negotiations at Torquay, England, on September 28th of this year. The conference this fall will constitute the "third round" of tariff negotiations under the General Agreement on Tariffs and Trade concluded at Geneva in 1947. The United States plans to negotiate with 17 other countries on possible tariff modifications on various articles all the way from baby carriages and bottle caps to lead and zinc-bearing ores. On May 31, June 1 and June 2, spokesmen appeared before the Committee for Reciprocity Information on behalf of the domestic lead and zinc mining industries. Producers of these metals protested the inclusion of paragraphs 391 (lead-bearing ores, dust and mattes), 392 (lead bullion, lead in pigs and bars, and scrap lead), 393 (zinc-bearing ores of all kinds), and 394 (zinc in blocks, pigs or slabs, and zinc dust) of the Tariff Act of 1930, as amended in the list of articles to be considered for possible tariff concessions at Torquay. It was pointed out that although operating costs have more than doubled since 1939 tariffs on these metals were actually higher in that year than at present. This, coupled with the detrimental effects of the recent series of devaluations, has sounded the death knell for a substantial number of domestic lead and zinc mines-a most undesirable development in the face of the ominous international situation, according to these spokesmen. It was urged that higher rather than lower tariff rates are needed on these metals. The opinion was expressed that it was inconsistent to foster a high living standard in our western areas and then, once it is attained, to undermine that condition by minimizing the protection that was partly responsible for it. The main theme of some arguments implied that although every effort should be made to close the "dollar gap" abroad, serious consideration must be given the methods employed lest our national security position be jeopardized in the process. The House Committee on Foreign Affairs completed hearings on H. J. Res. 236, to provide for United States membership and participation in the International Trade Organization. Hearings began on April 19th and ran for over five weeks. Many witnesses from industry and government presented voluminous testimony, which will not be available for public distribution for several weeks. However, it is no secret that the most controversial provisions of the Draft Charter of the ITO are: (1) Article 17 (Chapter IV on Commercial Policy) which would obligate members to negotiate for the reduction of tariffs and the elimination of trade preferences; (2) Article 20 which would prohibit the use of quantitative restrictions for protective purposes; (3) Article 16 which promulgates rules to implement the principle of non-discrimination in international trade; and (4) provisions permitting the use of protective measures for promoting economic development, particularly in backward areas, even though such provisions are inconsistent with those of the three articles cited above. United States membership in the International Trade Organization is essential to the successful operation of that body in view of this country's position as the economic giant in the present international trade pattern. Many countries are reluctant to take any action toward the ratification of the charter until it is known what course America will pursue. However desirable or undesirable the ideal of free multilateral trade may be it is unlikely that this Government's participation in the ITO will materialize soon. Advices in Washington indicate that H. J. Res. 236 will not be enacted during the present session of Congress. The legislative pattern designed to secure Congressional approval of the ITO is similar to that of the St. Lawrence Seaway project. The Seaway project was pending in treaty form for several years before the Foreign Relations Committee of the Senate and when the Administration decided to incorporate this project into bill form it was found that, while it passed the House promptly, the Senate decided to pigeonhole it because of the obvious intent to circumvent the constitutional prerogative of the Senate to advise and consent to the ratification of treaties. The ITO bill may be slated for a similar fate. It is deemed essential by western Senators and Congressmen that the present session of Congress enact some form of mining legislation before its adjournment, now set for July 31st. These legislators from prominent ore-producing states do not desire to return to their home areas in the fall emptyhanded. Aside from that, it is entirely superfluous to reiterate the necessity for maintaining a healthy domestic mining industry as a bulwark against a sharp rise in the temperature of the "cold war". Now that S. 2105 has failed a new bill is taking shape in the Senate Interior and Insular Affairs Committee. It is similar in language to H. R. 8221 (to encourage the conservation and development of the mineral resources of the United States) reported by the House Public Lands Committee on May 3, 1950, but so far has failed to receive approval of the House Committee on Rules. There are some qualified observers in high circles in Washington as well as in the mining industry who favor a tax incentive program to stimulate investment in mining enterprises, as opposed to a conservation and exploration program. The Bureau of Mines and the Treasury Department have undertaken a joint study to determine the need for modification of the tax laws as they apply to mining. The study is scheduled for completion before the end of the year, and appears to be supplementary to the investigation initiated by the National Minerals Advisory Council which culminated in the submittal of recommendations to the Secretary of the Interior in December 1949. The "cold war" is largely responsible for the increased demand for metals. Stock-pile purchases and heavy industrial demand due to military needs distort markets and disrupt normal price trends. Such activity has an unhealthy influence on metal production, luring some producers into a state of dependency on the continuation of this condition. When stock-pile objectives are met sometime in the future purchases must then come to a halt unless international "fireworks" are touched off. It can only be hoped that technological improvements and further mechanization of mines coupled with the stimulus of a rising population will offset the anticipated drop in industrial demand and cessation of stockpile purchases when the international crisis abates.

Jan 7, 1950

By W. A. Bruce

Studies of reservoir behavior of 12 Smackover limestone oil and condensate pools are presented. Buckner, Midway, McKamie, Magnolia, Mt. Holly, Schuler (Reynolds) and Village are treated in considerable detail and subjected to analysis with an electrical device for analyzing reservoir behavior. Results and comparisons of these analyses are presented. In addition to these reservoir-behavior studies, an attempt is made to assemble trans-missibility and storage data on the Smackover limestone formation from cores and logs taken in dry holes and producers. This together with the behavior of individual reservoirs leads to a better understanding of the formation as a porous aquifer. The ultimate purpose of this type of study is to improve predictions concerning the future behavior of these pools in such a system. Predictions are presented for several pools. Introduction In 1937 the Phillips Petroleum Co. drilled its J. D. Reynolds No. I to the Smackover limestone formation at Snow Hill, Arkansas. This well found oil in the porous, permeable, upper part of the Smackover, thereafter referred to as the Reynolds lime. Since then, six oil pools and six condensate pools have been discovered in the Reynolds lime, and more than 75 dry holes have explored parts of this formation. By the first of 1943, 44 million barrels of oil and 83 billion cubic feet of gas had been withdrawn from the various reservoirs. The original reserves estimated by the Arkansas Oil and Gas Commission were 342 million barrels of oil and rzoo billion cubic feet of gas. So far all of the production has been from anticlinal structures, most of which are asymmetric and have their axes roughly perpendicular to the dip of the formation top. This is indicated in Fig. I, which shows the pools, dry holes drilled, and contours on top of the Smackover.' These pools are of particular interest for reservoir-behavior studies because the production and drilling has been controlled, and in most cases the records of reservoir data are complete. In addition to the excellent production and pressure information available, more than one half of the wells drilled were cored and all of them were electrically logged. All of the pools show evidence of water drive. While this paper is in a sense a collection of reservoir-behavior studies for several different pools, there has been an attempt to go one step further and to show the importance of the iormation as a porous continuum or a single aquifer in which the withdrawals of fluids from any pool has an important effect on the behavior of all of the pools. An effort will be made to show that the water drives of these pools are dependent upon a much larger area of the Smackover limestone than that occupied by the petroleum accumulations.

Jan 1, 1944

By W. A. Bruce

Studies of reservoir behavior of 12 Smackover limestone oil and condensate pools are presented. Buckner, Midway, McKamie, Magnolia, Mt. Holly, Schuler (Reynolds) and Village are treated in considerable detail and subjected to analysis with an electrical device for analyzing reservoir behavior. Results and comparisons of these analyses are presented. In addition to these reservoir-behavior studies, an attempt is made to assemble trans-missibility and storage data on the Smackover limestone formation from cores and logs taken in dry holes and producers. This together with the behavior of individual reservoirs leads to a better understanding of the formation as a porous aquifer. The ultimate purpose of this type of study is to improve predictions concerning the future behavior of these pools in such a system. Predictions are presented for several pools. Introduction In 1937 the Phillips Petroleum Co. drilled its J. D. Reynolds No. I to the Smackover limestone formation at Snow Hill, Arkansas. This well found oil in the porous, permeable, upper part of the Smackover, thereafter referred to as the Reynolds lime. Since then, six oil pools and six condensate pools have been discovered in the Reynolds lime, and more than 75 dry holes have explored parts of this formation. By the first of 1943, 44 million barrels of oil and 83 billion cubic feet of gas had been withdrawn from the various reservoirs. The original reserves estimated by the Arkansas Oil and Gas Commission were 342 million barrels of oil and rzoo billion cubic feet of gas. So far all of the production has been from anticlinal structures, most of which are asymmetric and have their axes roughly perpendicular to the dip of the formation top. This is indicated in Fig. I, which shows the pools, dry holes drilled, and contours on top of the Smackover.' These pools are of particular interest for reservoir-behavior studies because the production and drilling has been controlled, and in most cases the records of reservoir data are complete. In addition to the excellent production and pressure information available, more than one half of the wells drilled were cored and all of them were electrically logged. All of the pools show evidence of water drive. While this paper is in a sense a collection of reservoir-behavior studies for several different pools, there has been an attempt to go one step further and to show the importance of the iormation as a porous continuum or a single aquifer in which the withdrawals of fluids from any pool has an important effect on the behavior of all of the pools. An effort will be made to show that the water drives of these pools are dependent upon a much larger area of the Smackover limestone than that occupied by the petroleum accumulations.

Jan 1, 1944

By Richard Downs, Stephen P. Burke

The oxidation of pyritic sulphur associated with coal is important for the following reasons: 1. It is the predominant cause for the formation of acid mine drainage issuing from bituminous coal seams. This drainage pollutes the streams in coal regions, making the water unfit for industrial purposes and causing the disappearance of fish and wild life. As a consequence the movement of industry and especially recreational industry, so important to the population of these areas as an alternative means of livelihood, is impeded. 2. It is instrumental in effecting a series of reactions, which bring about the degradation and ultimately result in the spontaneous combustion of bituminous coal in storage. 3. It contributes to the breaking and shattering of the coal structure and is one of the causes of roof falls and floor lifts in mines. 4. It is the primary cause of the many nuisances associated with gob piles and the refuse of cleaning plants. 5. Its proper control and application might possibly be employed in the preparation of coal to reduce the inorganic sulphur content. The research that has been conducted on the oxidation of the various forms of iron sulphides is extensive and the literature voluminous. Nevertheless, few efforts have been made to determine experimentally and with some precision the mechanism of the reaction under the conditions of its occurrence in bituminous coal mines. It has generally been accepted that the oxidation of pyritic sulphur proceeds according to the reaction 2FeS2 + 2H2O + 7O2 ? 2FeSO4 + 2H2SO4 [1] The ferrous sulphate in the drainage streams is further oxidized by air to produce ferric hydroxide and more acid. Yet the literature fails to disclose any pertinent investigation on the mechanism of this reaction. The present contribution is concerned primarily with this aspect of the problem and while the work to be reported is not yet complete, it has yielded results from which interesting and significant conclusions may be drawn.

Jan 1, 1938

By Richard Downs, Stephen P. Burke

The oxidation of pyritic sulphur associated with coal is important for the following reasons: 1. It is the predominant cause for the formation of acid mine drainage issuing from bituminous coal seams. This drainage pollutes the streams in coal regions, making the water unfit for industrial purposes and causing the disappearance of fish and wild life. As a consequence the movement of industry and especially recreational industry, so important to the population of these areas as an alternative means of livelihood, is impeded. 2. It is instrumental in effecting a series of reactions, which bring about the degradation and ultimately result in the spontaneous combustion of bituminous coal in storage. 3. It contributes to the breaking and shattering of the coal structure and is one of the causes of roof falls and floor lifts in mines. 4. It is the primary cause of the many nuisances associated with gob piles and the refuse of cleaning plants. 5. Its proper control and application might possibly be employed in the preparation of coal to reduce the inorganic sulphur content. The research that has been conducted on the oxidation of the various forms of iron sulphides is extensive and the literature voluminous. Nevertheless, few efforts have been made to determine experimentally and with some precision the mechanism of the reaction under the conditions of its occurrence in bituminous coal mines. It has generally been accepted that the oxidation of pyritic sulphur proceeds according to the reaction 2FeS2 + 2H2O + 7O2 ? 2FeSO4 + 2H2SO4 [1] The ferrous sulphate in the drainage streams is further oxidized by air to produce ferric hydroxide and more acid. Yet the literature fails to disclose any pertinent investigation on the mechanism of this reaction. The present contribution is concerned primarily with this aspect of the problem and while the work to be reported is not yet complete, it has yielded results from which interesting and significant conclusions may be drawn.

Jan 1, 1938

By D. C. McLean

This report summarizes the work that has been done during the past several years in adapting resins for use as auxiliaries in mine roof support. The resins were applied in two ways: 1) by injection into the strata, and 2) as a bonding agent for roof bolts and reinforcing bar. The Explosives and Mining Chemicals Department of the American Cyanamid Co. has worked during this period in cooperation with the Roof Control Research Group of the U.S. Bureau of Mines, the Pattin Manufacturing Co., the J. H. Fletcher Co., the Homestake Mining Co., the U.S. Steel Corp., the National Mines Corp. and the Pocahontas Land Corp. in an effort to create resin formulations and methods for applying them as a practical and sate type of roof support for mining areas particularly where conventional support is inadequate, yet expensive. This, work has involved much pioneering in a field where theory, speculation, and pure mythology predominates, and little basic engineering data is available. It is strange butt true that, despite the importance of roof control both from an operational and safely standpoint, there is scarcely a mining' company in this country that has an engineer, or anyone, assigned to the study of roof support problem, except temporarily--after a bad roof fall. The responsibility for improving roof control methods seems to have been placed entirely upon the shoulder, of the USBM, various State departments of mines, and individual roof bolt manufacturing; companies. It was in cooperation with the USBM that Cyanamid first developed resins for mining use.

Jan 1, 1964