Search Documents

By W. A. James

NATURE endowed the Niagara Frontier with great resources but it was the molding of these resources by the early pioneers that assured its future development. This great industrial district of New York stretches along about fifty miles of shore line on the eastern end of Lake Erie and the Niagara River, embracing the two counties of Erie and Niagara, with the city of Buffalo about in the center. This location at the junction of the eastern end of the Great Lakes and the western boundary of the State, a great focal point of land and water, transportation, guaranteed the development of the Frontier. Although the first white settlers came to this section in 1784, it was not until after the turn of the nineteenth century that real development started. Perhaps the most significant influence in the early days was the completion of the Erie Canal between Buffalo and Albany in 1825. This then monumental achievement gave Buffalo an advantage in the race for the best trade route to the Western

Jan 1, 1938

By Orson Shepard

THE leaching method that was first widely used with the cyanide process consisted of percolation leaching of crushed ore in vats or leaching tanks. It was frequently necessary to separate the sand for cyanide treatment and discard the slimes, because only granular material allows the necessary amount of solution to percolate through it in a reasonable time. Later a slime process consisting of agitation followed by thick-ening and filtration was developed, and is extensively used to the pres-ent day. Even though the agitation-leaching slime process is considered satis-factory, the cost of plant and of operation are both greater than for a percolation-leaching plant of equal capacity. This situation has been recognized in the hydrometallurgical treatment of copper-bearing slimes; and a considerable amount of j work has been done at the Southwest Experiment Station of the U. S. Bureau of Mines in an effort to develop a percolation method of treating slimes. Experimental work on the copper-leaching problem was started by H. E. Keyes1, and later tests were made by J. D. Sullivan and A. P. Towne2. The Bureau of Mines work resulted in the development of a process by which slimes were moisture-agglomerated with sand and crushed ore, to form a permeable mass through which solution could be trickled without breaking clown the glomerules. The agglomeration trickle-leaching method was devel-oped on a small scale and finally tried out in a 12-ton vat. Successful results were obtained as long is the leach solution was added slowly, so that the agglomerated charge was never flooded. If the leach solu-tion flooded the charge, the glomerules broke down and, the charge became impervious. There are two important difficulties in the application of the agglom-eration trickle-leaching-method to the cyanide process for gold and silver ores:

Jan 1, 1937

By R. S. Dean

REQUIREMENTS for war materials have led to large scale experimentation upon metallurgical innovations. It is of interest to inquire what this may contribute of permanent value to our existing technology, as innovations adopted during war are apt to be discarded promptly at its end. This is because utilization of substandard ores usually requires a new technology for ore treatment, and a new use-pattern for employment of the products. Thus two very different problems are involved: first, devising a process; then, adopting its products by industry, with readjustments of the use-pattern if necessary. A new process may be as good or better than an old one, but the readjustments required for use of its products may prevent its general adoption if this implies scrapping existing plants and investing much additional capital. Metallurgical innovations are of three kinds: I. The use of substandard material in processes already established; 2. The grading-up of substandard material to render it more suitable for established processes; 3. The adjustment of technology and use-pattern to the raw materials that we have.

Jan 1, 1945

By Anthony William Deller

MAJOR battles in the present war have been fought in American research laboratories. Without the outstanding contributions made by our scientists, engineers, and technologists in mining and metallurgy, many of our achievements in the present war would have been impossible. All recognize the fact that modern research has found the answer to problems which seemed insuperable. For the duration, many of these inventions must be maintained as war secrets. But aside from these, the record of accomplishment in peace and war, especially in the past few decades, known to all, demonstrates what scientific and industrial research can accomplish. It may be regarded as axiomatic that the development of modern industry is based principally upon research devoted to making inventions and discoveries. We have come a long way from the sixteenth century, when Agricola published his classical "De Re Metallica:" With our vastly increased knowledge we are now commercially producing dozens of metals entirely unknown at that time. Further, with our modern methods of research and development, a large number of invaluable alloy compositions have been produced. These include numerous age-hardenable alloys, cupronickels, "Everbrite", "Everdur", "Duralumin", "Elinvar", "Hastelloy", "Inconel", "Invar", "Monel", "Ni-chrome", "Ni-Hard", "Ni-Resist", "Permaloy", "Silcrome", stainless steels and irons and other alloy steels, "Stellite", and zinc die-casting alloys.

Jan 1, 1945

By Clarence A. Seyler

The object of all classification is to group together things which are alike, and separate those which are unlike. This object is essentially a practical one, enabling us to apply past experience to new conditions. Many costly large-scale experiments lose half their importance for want of proper description of the coal used, and the consequent impossibility of predicting that other coals will behave in the same way. I do not, therefore, make a fundamental distinction between "scientific'' and "use" classifications, except in so far as use depends on conditions, such as size or impurities which are not related to the nature of the coal substance itself. The characters chosen to define the classes of coal must be such as are accompanied by as many other properties as possible. It is not to be expected that any system of classification will enable us to predict every property of coal, since all specimens have an individuality of their own. But specimens can be grouped by a number of resemblances into species. Further, species which resemble each other can be grouped into genera. Elementary Composition as a Basis of Classification There can be little doubt that the ultimate or elementary composition of "pure coal" is the best basis of classification. It was soon after the perfection of the method of elementary analysis of organic substances by Liebig that Regnault, the distinguished chemist and physicist, laid down the principle that coals of the same kind vary only between narrow limits of elementary composition. This is still the widest generalization that can be made about coal. Upon it the metallurgist Gruner based his classification. In some quarters the value of the ultimate composition was denied, Stein going so far as to say that it teaches us nothing of importance about coal. One still hears statements that it is like crushing a work of art in a mortar and analyzing the powder, or like counting the number of times a given letter occurs in a sentence. Such comparisons are misleading, and the criticism might be applied to organic chemistry as a whole. Nor is the existence of isomerism, or of entirely different substances which

Jan 1, 1928

By C. V. Millikan

THE year 1930 in the petroleum industry has been characterized by the establishment of large potential production of crude oil. This has resulted in closer cooperation between companies by proration and unit operation agreements in order to afford an equitable outlet to all, and to prevent a flood of oil being forced on the market with attendant tremendous material and economic waste. Drilling wells in proved areas and wildcat wells are fewer than in the past several years. Restricted production and low prices have caused greater effort to increase producing and recovery efficiencies. Increased refinery efficiencies have amplified the effect of overproduction. Pipe line departments have been especially busy. New oil lines have reached more refineries by new and shorter routes. Establishing greater gas reserves by new fields has justified new gas lines to industrial centers, and has brought this fuel to thousands of new domestic consumers. Two long gasoline lines, a new venture in pipe lines, are being built to obtain a lower cost of transportation and less loss between the refineries and their distribution centers. The chairmen of the various divisions have discussed the developments of their respective branches more fully in the following reviews.

Jan 1, 1931

By C. C. Whittier

CIVILIZATION'S PROGRESS, which has multiplied man's comforts, conveniences, a n d happiness, is based upon the extensive employment of natural minerals and sources of energy. Mineral resources are basic factors in modern economic development, machine industry, international trade and world power. A survey of mineral consumption shows that the United States leads the world in the production and consumption of energy materials, of metals, and of the large and diverse array of earth materials that fall in the nonmetallic mineral group. The use of nonrnetallic minerals exceeded both the metals and the fuels in the long period before the industrial age, but it is only in the last two decades that consumption of non- metals has kept pace with and approximated in value the output of metals. Although the data of production in the first half of the last century are meager and fragmentary, the record of the past fifty years-the period of most rapid growth-is available, and reveals an astounding growth.

Jan 1, 1933

By William H. Spice

Exploratory drilling in South Central Texas for the year 1944 showed a marked increase over that of 1943 and resulted in a similar increase in new fields discovered. In this area, which comprises the 30 counties included in district No. I, Oil and Gas Division, Railroad Commission of Texas,? 61 exploratory wells were drilled during 1944 as compared with 29 exploratory wells drilled during 1943, or an increase of over 100 per cent. Three new oil fields, two new gas fields and one gas-distillate field were discovered during the year, as compared with one new oil field and one new gas field discovered during 1943. These new fields were the result of exploratory drilling throughout the district along the Wilcox trend and the deeper Edwards lime trend, which was started during the previous year. The Wilcox trend yielded the new Loma iilta-Wilcox oil field and the San Caja gas-* tlistillate field, both in McMullen County. The Charlotte field, in Atascosa County, was discovered along the deeper Edwards lime trend. These three discoveries were of considerable importance and subsequent development should indicate the desirability of continued exploration along these trends. The other three discoveries, United oil field in Guadalupe County, Pederson gas field in Milam County and Van Cleve gas field in Zavalla County, were of minor importance. Charlotte Field, Atascosa County, was discovered by the Humble Oil and Refining Company's No. 3 Pruitt, completcd on Aug. 9, 1944, flowing 176 bbl. per day, 3/16-in. choke, 710 lb. tubing, 475 lb. casing pressures, 37.7º A.P.I. gravity, from the top of the Edwards lime from 6917 to 6923 ft. Two oil wells were completed during the year in this field. This discovery is 14 miles southwest of the same company's Imogene field, also producing from the Edwards lime but with considerable difference in reservoir characteristics. The discovery of this field is the result of surface geology and subsequent seismograph survey of the area. Loma Alta-Wilcox Field, McMullen County, was discovered by the Atlantic Refining Company's No. I Atkinson, completed on June I, 1944, flowing 102 bbl. per day, 9/64-in. choke, 1900 lb. tubing pressure, 37º A.P.I. gravity, from Wilcox sand from 6866 to 6869 ft. after being drilled to a total depth of 7185 ft. This discovery is the result of subsurface geology and an extensive seismograph survey of the entire area. Sun Caja Field, McMullen County, was discovered by Edwin M. Jones No. 2-C Ezzell, completed on June 2, 1944 as a dual completion in the Wilcox sands, flowing 1,740,000 cu. ft. gas with 53 bbl. distillate, 1/4-in. choke, 2035 lb. tubing pressure, 53.2º A.P.I. gravity, from sand 6416 to 6453 ft. and flowing 2,000,000 cu. ft. of gas with 127 bbl. distillate, 1/4-in. choke, 2500 lb. tubing pressure, 50º A.P.I. gravity, from sand 6889 to 6916 ft., after being drilled to a total depth of 7264 ft. Three gas-distillate wells were completed during

Jan 1, 1945

By Ellis H. Gates

BENEFICIATION of the manganese oxide ores at Three Kids Mine near Henderson, Nev., has evolved over a period of years. Commercial application of the process is on a secure basis, and an effective working hypothesis has been formulated to help solve the problems encountered in flotation. An outstanding difference between the Manganese Inc. operation and other flotation processes is the necessity for high recovery of slime mineral values. Part of the manganese minerals in the Three Kids ore deposit occurs as primary slime or as minerals that are easily slimed by grinding. High recovery of this slime portion is essential to an economic overall manganese recovery. The aim of much of the research at Manganese Inc. was to recover these slimed and finely ground minerals by flotation. Early Agglomeration Processes: Tunbridge' in 1880, followed by Everson2 in 1886 and Cattermole" in 1904, discovered that under certain pulp conditions precious metals and sulfide minerals could be agglomerated if enough soap or oil were mixed into the pulp slurry. These agglomerated particles, Which under ideal conditions ranged from 1/16 to 1/4 in. diam, were recovered by screening, tabling, and hydraulic classification. Even flotation by air occluded in the agglomkrate particles by vigorous stirring was suggested. Cattermole nearly succeeded in getting his process into commercial operation, but it was finally abandoned, presumably because he could nat compete with the low reagent requirements of the new agitation froth process. Since Cattermole's time Christensen in 1921, Borcherdt4 in 1926, and Chapman and Littleford- in 1934 have attempted to apply the principles of agglomeration. In the light of current research at Manganese Inc. on conditioning of pulp at high energy input levels, it is interesting to note the variety of equipment such as tumbling mills, mixing drums, and shakers described by Borcherdt in his patent to produce the agglomerated particles. Ore Characteristics: Manganese in the Three Kids ore occurs as a 'complex mixture of manganese oxides commonly Known as wad. The manganese minerals have Been identified as psilorflelane, hollandite, coronadite, and pyrolusite with minor amdunts of rhodonite and rhodochrbsite. The ppincipal gangue miherals are quaktz, opal, kaolinite, montmoril-lonite, calcite, gypsum, fcelesitite, and barite. Most of the mangandse ore minerals are either porous and sponge-like in structure or soft clay-like masses composed of fine grained mineral particles approaching the size range of colloids. Consequently the ore minerals from the Three Kids mine have relatively large surface areas and high void content per unit weight. The specific area of various manganese ore samples measured at the California Research Corp. laboratories ranged from 32 to 58 sq m per g. The great surface area and high void content explains in part the unusually high reagent consumption required in the treatment of this ore. Current Milling Practice: At Henderson6 he ore is crushed to —1 in. and ground with rod mills in a closed circuit with spiral rake classifiers and cyclones. Sulfur dioxide solution is added to the pulp as it leaves the grinding circuit, immediately followed by addition of a reagent mixture of soap, oil, and wetting agent in the form of an emulsion. The reagents are initially well mixed into the pulp during their passage through centrifugal pumps to the conditioning equipment. All reagents are added prior to conditioning. The intense conditioning or mechanical stirring of the pulp, in which large amounts of power are consumed, is the principal difference between the flowsheet used at Manganese Inc. and a standard flotation circuit. As much as 38 kw-hr of energy per dry short ton of ore in a pulp containing 18 to 23 pct solids is used for conditioning. After conditioning, the pulp passes to a flotation circuit that consists of one roughing stage, a scav-

Jan 1, 1958

By Ralph Arnold

IN OPENING the symposium under the auspices of the Petroleum and Gas Committee of the American Institute of Mining and Metallurgical Engineers, I wish to call to your attention the following, among other subjects, which it is hoped may receive proper attention: 1. The recording of as accurate an appraisal of the oil possibilities of the various countries as is possible, with information as to the immediate availability of their supply. 2. The development of further support for the move-ment to bring about active cooperation among Ameri-can oil companies in their foreign exploration and development work. 3. The furtherance of the efforts of the industry in securing governmental assistance in foreign oil develop-ment: (a) along the lines of a modification of our domestic oil policy, so that we can go to foreign coun-tries and consistently ask fair treatment as to royalties and bonuses; (b) by a closer cooperation between the State and Commerce Departments and the oil industry. 4. The calling of attention to the unjustifiably drastic action of the price-fixing group of the oil industry during the last year or so, with the hope that it will use gentler methods in the future. None of these subjects are new, and some of them have been discussed before various organizations for years. Our justification for again bringing them forward is the hope that by everlastingly harping on them the industry, the Government, and the people who shape the destinies of this country may some time, some how, realize their importance and take effective constructive action.

Jan 6, 1922

By AIME AIME

MEXICO embraces one of the great metal and petroleum producing provinces of the world. In this respect its history dates back to the overthrow of the Aztec empire by a Spanish force under Hernando Cortes between 1519 and 1.521. Even before then, its richness in silver and other minerals was not unknown. But it was a treasure house for the Spanish conquerors until the country became independent in 1821. It has been computed that in the 400 years following 1521, Mexico yielded 1.55,000 metric tons of silver, worth $3,000,000,000, two-thirds of the entire world production. In 1935 the country accounted for 36 per cent of the world's silver output, 14 per cent of its antimony (in 1934), 13 per cent of its lead, 3 per cent of its zinc and copper, and 21/2 per cent of its petroleum. Contrary to the impression of some, its gold output is now comparatively small, though important in the past. Its oil, as well, formerly hulked much larger than now, in 1921 being one-fourth of the world output.

Jan 1, 1936

By R. E. Allen

ONE of the most unusual oil field engineering accomplishments of the past two years is the development and rapid advance in the directed drilling of wells. Directed drilling as referred to herein is the controlled steering of the drill stem in the required direction to a given location in the oil sand. The deliberate drifting of holes is an act so far removed from what has been considered good drilling practice that all of the old questions of correlation, drillability and production difficulties are revived. Only a few years ago, during the boom days of Seminole and Santa Fe Springs, the crooked-hole problem, as it was then called, occupied a primary position among the topics of the day in the fields of California and the Mid-Continent. The net result of all the discussion and study at that time was the conclusion that oil wells should be drilled with as little deviation from

Jan 1, 1933

By J. S. Marsh

AN incomplete statistical analysis performed wearily on the morning after Thursday, Feb. 12, indicates that the unavoidable items of conversation among steelmen were the current shortage of sleeping time and the "Normandie." No analysis is needed, however, to be certain that many thousands of valuable words were uttered, both in and out of technical sessions, concerning matters of deep interest to members of the Iron and Steel Division. The opening session consisted mostly of papers that have appeared, or will appear shortly, in Metals Technology. One, however, that was not finished in time to be printed in any form, but that aroused great interest, was by E. L. Ramsey and L. G. Graper (Wisconsin Steel Works). Its subject was the production of high-sulphur steel by treatment with sulphur dioxide derived from anhydrous sodium sulphite or bisulphite added to the ladle or to the mold. The sulphide distribution in the finished steel is such that increased machinability and longer tool life result. Both items are of obvious importance in these days of mighty production.

Jan 1, 1942

By K. P. Gupta, A. K. Pal, L. Chandrasekaran, U. P. Singh

The Mn-Sn binary system, investigated at the high-manganese end and between 500° and 1000° C, shows four phases at temperatures below 727"C, namely the u Mn, the p Mn, the Mn3 Sn, and the Mn, Sn phases, while at higher temperatures only the last three phases remain stable. The solubility of tin in a Mn is very small and the maximum solubility of tin in P Mn phase appears to be abollt 10 at. pct Sn. The solubility range of the Mn,Sn and the Mn, Sn phases is 23.0 to 26.0 and 37.0 to 40.0 at. pct Sn, respectively. The lattice parameter of the 13 Mn phase increases with increasing tin content. The Mn, Sn thase is hexagonal with and appears to be basically of the Ni3 Sn type structure except that for quite a few X-ray diffraction lines the calculated and observed relative intensities do not agree well. The Mn-Sn binary system has been studied by several investigators.''~ Their results indicate that three intermediate phases, namely, the Mn3Sn, Mn,Sn, and MnSn, phases, exist at high concentrations of tin. However, so far the proper phase equilibrium has not been established at the manganese-rich end and very little data is available for the composition range between pure manganese and Mn3Sn. Moreover, earlier investigators differ in their opinion about the exact composition range at which the Mn3Sn and Mn,Sn phases appear and some doubt has been cast by some investigators3 regarding the structure of Mn3Sn phase which has been reported to be isotypic with Ni3Sn (Mgscd type) structure. In this investigation an attempt has been made to establish the proper phase equilibrium between pure manganese and Mn + 50 at. pct Sn composition in the temperature range of 500" to 1000°C. PROCEDURE The raw materials used were from three different sources. For exploratory work five alloys containing 5, 10, 15, 20, and 25 at. pct Sn were prepared using 99.9 pct pure manganese and tin supplied by E. Merck & Co., Germany. The rest of the alloys and one more 25 at. pct Sn alloy were prepared using 99.9 pct Mn supplied by Gallard Schlesinger Chemical Mfg. Corp., U.S.A., and 99.999 pct Sn supplied by Semi Elements Inc., U.S.A. Weighed amounts of manganese and tin were melted in recrystallized alumina crucibles in an inert gas (argon) high-frequency induction melting furnace. By careful control of temperature and time of melting the losses were reduced to below 0.2 pct in all cases. Since the losses were very small, no attempt was made here to analyze the samples chemically. Alloys were wrapped in molybdenum foil and sealed in small evacuated fused silica capsules. The alloys were annealed at different temperatures, controlled within + l°C, for sufficiently long periods to attain proper phase equilibrium, and subsequently quenched in cold tap water. The annealing periods used at different temperatures were 15 days at 500°C, 7 days at 600°C, 5 days at 700" and 750°C, 3 days at 800°, 850°, and 900°C, 2 days at 968"C, and two alloys annealed at 968°C were reannealed for 10 hr at 1000° C. From each annealed specimen, a part was utilized for metallographic study while another piece was used for X-ray diffraction study. 1.0 pct HNO, solution and oxalic acid solutions of concentrations 0.05 to 1.0 pct were used for etching Mn-Sn alloys above and below the MnsSn composition, respectively. Since all alloys were brittle, X-ray specimens were prepared using the as-crushed -325 mesh alloy powders. Only one 25 at. pct Sn alloy powder was reannealed in an evacuated silica capsule at 800°C for 5 min and water-quenched. X-ray diffraction patterns . for the Mn3Sn phase with the as-crushed and the reannealed powders did not show appreciable change. Un-filtered iron radiation at 25 kv, 15 ma was used with either Norelco 114.6-mm-diam Debye Scherrer Camera (for phase identification) or Norelco 12-cm-diam symmetrical focusing camera (for lattice parameter determination of the 6 Mn phase). The estimated accuracy of lattice parameter determination for the focusing camera was * 0.001A. RESULTS AND DISCUSSIONS The results of metallographic and X-ray diffraction study made with different alloys are shown in Fig. 1. The variations in lattice parameter with composition for the p Mn and the Mn3Sn phases are given in Tables I and 11, respectively, and the lattice parameter as a function of composition for the p Mn phase is shown in Fig. 2. The lattice parameter of the p Mn phase increases with increasing tin content while for the Mn,Sn phase the data obtained from two two-phase alloys and one single-phase alloy indicate increase in a,, and decrease in c, parameters with increasing tin content. The results, Fig. 1, indicate that the solubility of

Jan 1, 1969

By F. H. Deily, L. W. Ledgerwood, J. E. Eckel

A new method for drilling the earth's formations has undergone extensive laboratory and shallow earth drilling experimentation. This method, pellet impact drilling, uses the energy of a large mass of high velocity steel spheres to break and crush the rock. Pellets are confined to a region close to the hole bottom. Motive fluid for transporting and recycling the pellets is supplied by a modified jet pump. The pellet drilling method has inherent advantages over conventional rotary drilling. First, only a nominal amount of weight need be applied to the hole bottom. Second, only a very small amount of torque is required for bit rotation. Third, means are available for continual replacement of the cutter medium. The experimental laboratory work and analytical procedures necessary for the design of a pellet drill bit are described. In the laboratory program approximately half the effort was devoted to the development of a better understanding of the physical process, and half to the empirical testing of new bit configurations. Factors such as pellet size and velocity, jet pump characteristics and modifications, and power distribution are discussed. The design and construction of a pellet impact bit for drilling a 9 in. hole with 1 1/4 in. steel pellets are described. Drilling performance in representative rocks, hydraulic operating characteristics, and metallurgical problems are discussed. INTRODUCTION This paper discusses an attempt to reduce drilling costs through the development of a drilling method basically different from rotary drilling. Publications on drilling research indicate that the major effort on the part of manufacturers and operators has been confined to research in rotary, or rotary-percussion drilling. This applied drilling research has produced significant gains in drilling rates and bit life, but thus far it has failed to achieve any major decrease in general drilling costs. From recent statistics released by Drilling Contractors, it can be shown that the total cost of drilling an "average" well in 1953 was about 2 1/4 times the corresponding cost in 1935. Analysis of the costs will show that they are not due to inefficient field operations; they are due instead to both an inflated economy and greater "average" well depths. Diligent work by the industry has reduced the backlog of potential economic improvements in rotary drilling to a group of rather marginal prospects. Increasing depths and poorer quality reservoirs at these depths continue to make the drilling cost problem more acute. Hence, the aim of the work reported here was to develop a new drilling method not limited by the inherent characteristics of rotary drilling and thus capable of attaining further significant reductions in drilling costs. The effort devoted to research on this proposed new drilling method was of considerable magnitude and represented .in excess of 37 man-years of research. The affiliates of Standard Oil Co. (N. I.) sponsored this development program which was conducted by the Drilling Methods Section of the Carter Research Laboratory in Tulsa, Okla. The purpose of this paper is to

Jan 1, 1957

By W. A. Ver Wiebe

The year 1938, with a production of 58,784,250 bbl. from 18,790 wells shows a slight recession from the high peak of oil production reached the previous year, when slightly over 68 million barrels of oil was marketed. The previous high peak had been reached in 1917 with a total of 45,451,000 bbl. Another still earlier peak was reached in 1904, during which year slightly less than 5 million barrels was produced and sold. The production of gas, on the other hand, probably reached a new peak during 1938 with a total of over 60 billion cubic feet. This peak, however, was not the highest peak, for during the year 1908 over 80 billion cubic feet was produced. Between these two high peaks the production dropped down to 16 billion cubic feet in the year 1921. The number of wells drilled during the year totals 1569. This figure is somewhat lower than the figure given in several trade journals because it does not include wells that were deepened or recompleted in a different geological horizon. Nearly three-fourths (or 1107) of the total number of wells were completed as commercial oil wells (915 in western and 192 wells in eastern Kansas). The commercial gas wells completed number 50, of which 4 are in eastern Kansas and 46 in western Kansas. The remaining 412 completions include 130 dry holes in eastern and 282 dry holes in western Kansas. Based on daily potential capacity, the new discoveries of the year accounted for 70,000 bbl. of new oil for eastern and 1,220,000 bbl. of new oil for western Kansas. It is interesting to note in this connection that the number of wells completed in the state rose gradualIy to a first peak in 1904, when 2782 were drilled. The number dropped off rapidly to 368 three years later, but rose to the second and highest peak in 1918 when 4671 wells were completed. In the period between 1904 and 1912 more gas wells than oil wells were completed. Between the high peak of 1918 and the somewhat lower peak in 1937, the low point was reached during 1931, with the completion of only 470 wells. In the matter of new pools discovered, Kansas again ranks high. The exact number depends somewhat upon the interpretation of a new area whether it should be called a new pool or a long extension of an

Jan 1, 1939

By W. A. Ver Wiebe

The year 1938, with a production of 58,784,250 bbl. from 18,790 wells shows a slight recession from the high peak of oil production reached the previous year, when slightly over 68 million barrels of oil was marketed. The previous high peak had been reached in 1917 with a total of 45,451,000 bbl. Another still earlier peak was reached in 1904, during which year slightly less than 5 million barrels was produced and sold. The production of gas, on the other hand, probably reached a new peak during 1938 with a total of over 60 billion cubic feet. This peak, however, was not the highest peak, for during the year 1908 over 80 billion cubic feet was produced. Between these two high peaks the production dropped down to 16 billion cubic feet in the year 1921. The number of wells drilled during the year totals 1569. This figure is somewhat lower than the figure given in several trade journals because it does not include wells that were deepened or recompleted in a different geological horizon. Nearly three-fourths (or 1107) of the total number of wells were completed as commercial oil wells (915 in western and 192 wells in eastern Kansas). The commercial gas wells completed number 50, of which 4 are in eastern Kansas and 46 in western Kansas. The remaining 412 completions include 130 dry holes in eastern and 282 dry holes in western Kansas. Based on daily potential capacity, the new discoveries of the year accounted for 70,000 bbl. of new oil for eastern and 1,220,000 bbl. of new oil for western Kansas. It is interesting to note in this connection that the number of wells completed in the state rose gradualIy to a first peak in 1904, when 2782 were drilled. The number dropped off rapidly to 368 three years later, but rose to the second and highest peak in 1918 when 4671 wells were completed. In the period between 1904 and 1912 more gas wells than oil wells were completed. Between the high peak of 1918 and the somewhat lower peak in 1937, the low point was reached during 1931, with the completion of only 470 wells. In the matter of new pools discovered, Kansas again ranks high. The exact number depends somewhat upon the interpretation of a new area whether it should be called a new pool or a long extension of an

Jan 1, 1939

By P. Gobin, J. Perez, P. Peguin

The strain-amplitude- dependent part of the internal friction of alluminum after several ther momechanical treatments has been measured in the I-cycle range and at the ambient temperature. The internal friction in the outer layer of the torsional specimen us stress is computed from the experimental data. The curues obtained are analyzed in tevnzs of u coirzbinntion of AH and p, which aye, respectively, due to the vecersible unpinning from weak pills and to the plastic strain. Considerirlg the notion of thermally activated unpinning and repinning, it is shown that in our experimental conditions tlze dislocation lines acl as in the H model of Granato and Liiclze. It is also seen that the internal friction p which appears at higher- strains call be described by a simple expression which is in good agreement with our results. A qualitative interpretatiorz is proposed by combining these new types of intelpnal fviction. We define the internal friction 6 as half the ratio of the dissipated energy aW during one cycle to the maximum supplied strain energy W of a material submitted to a periodic stress. Experiment and theory show that internal friction varies with stress above a critical value.' Below this value the internal friction is strain-amplitude-independent and is often masked by an experimental background; so we shall call it AB. ~bove this critical value, the internal friction is strain-amplitude-dependent. This quantity is usually called aH:' and it can be explained as a thermal unpinning of dislocations.3-6 Furthermore, at higher stresses, a rapid increase of internal friction appears. This phenomenon could be caused by the plastic strain,' so we shall call it Ap. It seems interesting to us to study the influence of several t her momechanical treatments on the curve internal friction 6 vs strain E, in order to study the variation of AH and p with the concentration and the repartition of linear and point defects. In order to try to explain the results obtained, we shall propose and discuss models for H and hp and shall show that we obtain a combination of these two types of internal friction. 1) EXPERIMENTAL PROCEDURE 1) Preparation and Treatment of Specimens. We

Jan 1, 1968

By H. W. Hitzrot, R. H. Limons, L. V. Fegan

The testing of a new method for measuring pellet-bed temperatures in the traveling-grate or shaft furnace is presented in this paper. This method, using silver-palladium alloy wires as indicators, overcomes disadvantages existing in the methods based on the use of thermocouples which are costly and time-consuming. The authors have developed and tested a new method for measuring pellet-bed temperatures in the traveling-grate or shaft turnace through the use of silver-palladium alloy wires as indicators. This method overcomes the disadvantages of existing methods, which, based on the use of thermocouples, are generally costly and time-consuming. For example, in the case of the traveling-grate furnace, the installation of an instrumented pellet, together with its attached thermocouples, requires stopping the furnace, with resulting loss of production time. As for temperature measurement in the shaft furnace by the existing method, the movement of the shuttle-car feeder seriously interferes with both the actual insertion and the resulting distribution of continuously fed thermocouples. The authors have overcome these difficulties by using, as temperature indicators, a range of silver-palladium alloy wires that can be easily recovered, after firing at any desired location in a pellet furnace. Silver-palladium wires having specific melting points from 2000°F to 2500°F are enclosed in ceramic capsules. Each capsule is placed in a ni-chrome wire basket filled with a sample of green pellets, the baskets being the means for recovering the capsule after firing. After the encapsulated wires have been exposed to the firing cycle, the alloy wires are examined to determine the maximum temperatures attained by the pellet sample. This method gives accurate, rapid determinations of maximum temperatures attained during pellet induration in either the traveling-grate or shaft furnace The new method has the following advantages over existing methods: 1) it is less expensive; 2) no furnace downtime is required; 3) the testing units can, be made in quantity in advance; 4) measurements can be made in rapid succession at all desired locations; 5) measurements of maximum firing temperatures are more accurate; 6) on the basis of points 4 and 5, the new method gives a more reliable picture of the correlation of pellet quality, petrographic textures and maximum temperatures, thus providing a more effective quality-control tool. A disadvantage of the method is, of course, that the measurements are not continuous and only maximum temperatures are determined. TEST PROGRAM Preparation of Materials: CALIBRATION OF ALLOYS - In the following discussion the term "bead point" (see Fig. 1) refers to the temperature at which each alloy begins to melt and form a bead. Fig. 2 gives the bead point curve for silver-palladium alloys. Before the alloys are used in plant tests, the bead point of each alloy should be determined in the laboratory to verify the alloy compositions. Once a given alloy has been calibrated, it can be

Jan 1, 1965

By S. C. Sun

With the aid of emulsifiers, intense high-frequency sound waves are capable of emulsifying any collector in water. The data show also that ultrasonically emulsified collectors are more effective in floating minerals than the nonemulsified collectors. THE use of ultrasonics in forming emulsions is not new. As early as 1927 Wood and Loomis reported preparation of emulsions with ultrasonics. In 1935 Rschevkin and OstrawskyV escribed the use of great ultrasonic power in producing fine emulsions of various oils and paraffin in water. Recently Oyama and Tanaka3 employed ultra-emulsification to increase the effectiveness of sodium ethyl xanthate in flotation of chalcopyrite and galena. An emulsion is a two-phase system consisting of two incompletely miscible liquids, the one being dispersed as finite droplets In the other. The dispersed liquld is known as the internal or discontinuous phase, and the surrounding liquid is termed the external or continuous phase. There are two types of emulsions; one is oil-in-water (O/W) and the other water-in-oil (W/O). The word oil refers to the liquid other than water. Circumstances exist in which the emulsion type is not clearly defined, and the internal and external phases both contain portions of the opposite phase. This is said to be a dual emulsion. Among the many hypotheses, 5a, B proposed for the formation of emulsions, the Bancroft's adsorbed film or double interfacial tension theory is widely accepted. Bancroft 7, 8 deduced that in the process of emulsification the interfacial tension between oil and water is lowered by the formation of an emulsifying film, which contains the adsorbed molecules and/or ions from the emulsifying agent and the two liquids. This film has two interfacial tensions, one with the water and the other with the oil, which are not necessarily equal. The difference in interfacial tension between the two surfaces of the film is chiefly responsible for forming different types of emulsions. For example, if the interfacial tension between water and film is less than that between oil and film, the film will become convex on the water side, thereby tending to form an oil-in-water emulsion. On the other hand, if the interfacial tension between water and film is greater than that between oil and film, the film will become concave on the water side, thereby tending to make a water-in-oil emulsion. In line with this theory, emulsifying agents soluble in water have the tendency to form oil-in-water emulsions, while those soluble in oil form emulsions of the reverse type. Apparatus and Experimental Procedure: The ultrasonic apparatus shown in Fig. 1 consisted of a hypersonic generator (A), Brush Development Co. model Bu-204; a hypersonic transducer bowl (B) whose resonant frequency is 400 kc per sec; and a round-bottomed glass tube (C) of 2.2 cm ID and 21 cm in length. The acoustical output power of the hypersonic transducer bowl was standardized with a Hewlett Packard vacuum tube voltmeter, model 41 0B, across the hypersonic generator output. The glass tube, containing the materials to be emulsified, was placed 1 cm above the central surface of the transducer bowl, which was filled with water as shown in Fig. 2. Ultrasonic emulsification was performed in three steps, although a one-step method has been used: 1) emulsifying the predetermined amounts of col-

Jan 1, 1956