Search Documents

By Edgar Bain

THE results are presented of an investigation to discover the fundamental atomic conditions existing in Corson's high-copper alloys hardenable by means of silicide solution and reprecipitation. The study attracted the writer because it offered a very convenient example of the general type of hardenable alloys exemplified by duralumin, Sykes' iron-tungsten and iron-molybdenum alloys and the hardenable lead antimony. SUMMARY OF RESULTS AND CONCLUSIONS In brief, the investigation shows that very perfect crystallinity exists in the solid solutions prepared at high temperature to contain as much dissolved silicide as possible. The lattice parameter of copper is altered very little by the amount of cobalt, nickel or chromium, and silicon dissolved. The hardening by drawing at a temperature to initiate precipitation of excess silicon and metal produces a remarkable change in the atomistics of the solid solution. The old perfection of crystallinity in the solid solution is destroyed and the new atomic spacings are of variable magnitude even in one grain, and a condition in a measure resembling that found in martensite is observed. Were no particles whatever precipitated by the drawing action, still ample causes for hardness would be in evidence in the solid solution alone. The lack of plane continuity in the crystal grains would oppose slip in a very effective manner. Complete annealing restores the crystalline perfection in large measure. In these alloys even the most sensitive methods failed to reveal the characteristic pattern of the silicide precipitated by the anneal, but this was largely to be expected as the amount is relatively small.

Jan 1, 1927

By C. H. Stewart, R. A. Fagin

A two-dimensional, three-phasereservoir simulator was programmed for a large memory digital computer. It was designed to provide a practical solution to describing the complex physical relation between the natural forces and the physical properties of a heterogeneous reservoir when subjected to a specific set of conditions. A reservoir study is briefly described to illustrate application of the model. A full volumetric account of three phases (oil, gas and water) is performed simultaneously throughout an integration net representing the reservoir. Absence of one or two of the phases is treated as a special case of the more general situation. Expansion (or contraction) of all phases, including rock expansion, is performed so that the pressure calculation is the general unsteady-state case. To account for the large variations of subsurface elevation encountered in some reseruoirs, and to allow for segregation of the various phases, a gravity head term is included in the basic drive potential. Appropriate fluid and rock properties are used in polynominal surface form (functions of pressure and/or depth) or they can be entered as space variables at each position of the integration net. An unsteady-state water influx calculation, based on the method of van Everdingen and Hurst, l was connected to the boundary of the matrix to simulate aquifers of various sizes. In addition to reservoir calculations, three-phase fluid flow from the producing depth to the wellhead, including provisions for gas lift, was incorporated in the simulator. A workover routine was also built which can automatically switch to a different set of production relations when a gas-oil ratio or water fraction reaches a limit; or it can shut-in the well if prescribed. INTRODUCTION This paper describes a reservoir engineering mathematical simulator used to represent the complex interaction of natural forces and physical properties of a reservoir during natural depletion or with various injection schemes. The simulator, which was programmed for a large memory digital computer, is a two-dimensional calculation which handles three mobile fluid phases simultaneously (oil, gas and water). Basic requisites for the method are individual well production and pressure data, hydrocarbon fluid properties, geological data (producing depth and net sand), capillary pressure data, relative permeability data and permeability and porosity information. Matching the past performance of a combination drive reservoir often has yielded information concerning continuity and the validity of basic data. Detailed predictions of future performance can be made for continuation of current depletion methods (natural depletion) as well as for various types of recovery by gas or water injection. Combination injection cases and pattern studies can also be performed. Workover programs, gas lift and different types of artificial lift programs have been investigated using a technique similar to that described by Kern and Nicholson2 except that conditions of pressure and saturation at the block within which the well is located are used rather than average reservoir conditions. Drilling additional wells to optimize profit was explored, both as to number and location, by placing wells at different spots within the reservoir matrix. Special depletion processes can be examined, such as upstructure drainage and lateral (or strike) waterfloods in thin oil columns. In one case the mathematics of the simulator were modified to calculate the displacement in the vertical plane rather than in the horizontal plane. In this manner specific reservoir problems can be studied, such as coning of gas and/or water around production points, fingering along permeable stringers or, more generally, frontal advances in a heterogeneous section.

Jan 1, 1967

By Oliver Bowles

When a new type of equipment revolutionizes methods of quarrying one kind of stone, producers of other kinds focus their attention on its potentialities in their particular fields. The purpose of this paper is to discuss the accomplishments of the wire saw in slate, to show its more limited attainments in other kinds of stone, and to point out the possibilities of much wider application. A wire saw consists of a 3/16-in. or ji-in. three-strand wire cable that runs as a belt and cuts the rock by abrasion. (Fig. 1. The teeth of the saw are sand grains carried in the grooves between the strands. Accomplishments in Slate† Initial experiments with wire saws by the U. S. Bureau of Mines in the Colonial Slate Quarry, Wind Gap, Pa., in 1926, attained success so immediate and pronounced that within two years in virtually every quarry in the neighborhood of Wind Gap, Pen Argyl and Bangor, the most productive slate area in the United States, wire saws were substituted for channeling machines. An 80-ft. cut in slate is shown in Fig. 2. The technique of operation has been described in several reports (references at the end of the paper). The present purpose is to summarize the accomplishments in a large, typical slate quarry after nine. years of experience. Parsons Bros. Slate Co., at Pen Argyl, Pa., substituted two wire saws for six channeling machines in 1927. The following comparisons are made between the present method with wire saws and the former channel-ing-machine method. Rate of Sawing.—The average rate of cutting with a wire saw in the early days of its operation, as determined by the Bureau of Mines', wits 14 to 17 sq. ft. per hour. Parsons Bros. Slate Co. estimates the present rate of cutting at about 25 sq. ft. an hour, whereas the channeling-rnarhirle

Jan 1, 1938

By Oliver Bowles

When a new type of equipment revolutionizes methods of quarrying one kind of stone, producers of other kinds focus their attention on its potentialities in their particular fields. The purpose of this paper is to discuss the accomplishments of the wire saw in slate, to show its more limited attainments in other kinds of stone, and to point out the possibilities of much wider application. A wire saw consists of a 3/16-in. or ji-in. three-strand wire cable that runs as a belt and cuts the rock by abrasion. (Fig. 1. The teeth of the saw are sand grains carried in the grooves between the strands. Accomplishments in Slate† Initial experiments with wire saws by the U. S. Bureau of Mines in the Colonial Slate Quarry, Wind Gap, Pa., in 1926, attained success so immediate and pronounced that within two years in virtually every quarry in the neighborhood of Wind Gap, Pen Argyl and Bangor, the most productive slate area in the United States, wire saws were substituted for channeling machines. An 80-ft. cut in slate is shown in Fig. 2. The technique of operation has been described in several reports (references at the end of the paper). The present purpose is to summarize the accomplishments in a large, typical slate quarry after nine. years of experience. Parsons Bros. Slate Co., at Pen Argyl, Pa., substituted two wire saws for six channeling machines in 1927. The following comparisons are made between the present method with wire saws and the former channel-ing-machine method. Rate of Sawing.—The average rate of cutting with a wire saw in the early days of its operation, as determined by the Bureau of Mines', wits 14 to 17 sq. ft. per hour. Parsons Bros. Slate Co. estimates the present rate of cutting at about 25 sq. ft. an hour, whereas the channeling-rnarhirle

Jan 1, 1938

By Morris E. Fine, Richard A. Kloske

The stress-strain beha1,ior in tension of Au-Ag alloy single crystals containing nominally 1,3, 5, 95, 97, and 9.9 at. pct Ag was studied uS strain role and lektlperalure down lo 4.2K. A slrain aging yield hob lc,rrs observed on aging under stress in the temperature range 30° lo 75°C. The species diffusing to the dislocation is thought to be a divacancy-solute complex wilh /he. solute then pinning the dislocation by short-Range ovdering and possibly Suzuki locking. At room tempevullcve the critical reso1ved shear stress .follo~c.s an empirical equation of the form tc = A +Bc' where A and B are 90 and 420 ,g per sy mm tor gold base alloys and 60 and 510 g p~r sq )11ttz .tor si1ver base alloys. This strengthening was attributed to a long-range size ejtect. The alloy slrenglliening at i.2'K is greafer than at room temperature. The additional atrloutzf was altribuled lo a uwak skovl-range i?~levacIion between the solute and dislocallon cove. The activation energy .tor deformation a/ 4.Z0h7 decreases on alloying. 11 increases irr other fee systetns. hi the 5 at. pcl Air-Ag- alloy in pmvlicular there is very extensive easy glide and lavge overshooting- of the synmetry line at 4.Z°K. There is also u sharp decrease in the vale of. strain hardenitlg near the widdle of stage II with the new rate bezng abold the sarne as tlzal In easy glide. This uws attributed to a sudden reduction of activity on the pvitrrarg sgstertr. In Au-Ag alloys the critical resolved shear stress Tc. at room temperature is essentially a parabolic function of atomic concentration:' the 50 at. pct Ag-50 at. pct Au alloy is about 10 times stronger than the pure metals. This strengthening occurs in spite of the similarity in valence and atomic size. Solid-solution strengthening in fcc metals is characteristically greater at low temperatures than at room temperature. In Ag-10 at. pct Au and Au-10 at. pet Ag; r, (20.4K)/Tc (300°K) is 2.3 and 2.5. respectively.- compared to 1.2 in pure silver.3 Suzuki' and Flinn5 explained the alloy strengthening at room temperature as a combination of Suzuki locking and short-range order hardening. The agreement between the computed and measured strengthening was very good: however, in Ag base-A1 alloys Hendrickson and Fine6 concluded that Suzuki locking resulted mainly in a yield drop effect. Recent reviews of the solid-solution strengthening in fcc metals by Fleischer2 and Haasen8, 9attributed the strengthening at room tenl-perature to the combined effect of atom nlisfit and change in shear modulus 011 the long-range stress field surrounding a dislocation. The parameter used by Fleischer was The shear tnoduli of Ag-0 to 6 at. pct Au alloys were measured by Pur-wins. Labusch. and Haasen.In While addition of 4 at. pct Au caused an appreciable increase in the C,, elastic constant. there was a decrease on increasing the solute to 6 at. pct Au: C,, and C :: were not measured in the 6 at. pct alloy. The greater solution hardening at low temperatures implies the presence of short-range interactions between the solute atoms and dislocations These include size and electronegativity effects. Whether the extra alloy strengthening at low temperatures is due to locking or friction hardening is still a controversy."".' In the present research the stress-strain behavior of Au-Ag single crystals containing 1 to 5 at. pct Ag and 1 to 5 at. pct Au was measured vs strain rate and temperature down to 4.2' K. Particular attention was paid to yield drop effects. These have not been previously reported. PROCEDURES The alloys were supplied by the Engelhard Industries. Inc.. as strips 0.050 by 0.250 by 12 in. The compositions are given in Table I. Single crystals were grown under static vacuum using a traveling molten zone technique. Crucibles shaped to the size of the strips were made of high-purity graphite prebaked for 24 hr at 1100°C in vacuum. The crucible and its charge were placed in

Jan 1, 1970

By Donald A. Corrigan, John Chipman

It is shown that the heat of solution of nitrogen in liquid-iron alloys is Proportional to the interaction coefficient. This proportionality forms the basis for a method of predicting nilrogen solubility at any temperature when the interaction coefficient is knoun at 1600°C ov when the solubility is known at some one temperature. A method for predicting the solubility of nitrogen in liquid steels, including alloy steels, was proposed some years ago by Langenberg.' Since the data available at that time were restricted to temperatures of about 1600°C, his predictions were similarly restricted. More recently, Nelssonz devised an approximate method for estimating nitrogen solubilities at higher temperatures. It is the purpose of the present paper to present a method by which the solubility of nitrogen at any temperature within the steelmaking range may be predicted from the known interaction coefficients at 1600°C. Nitrogen in iron and in all of the alloys to be considered here is known to obey Sieverts' Law; hence the activity of nitrogen in an alloy of fixed composition is proportional to its concentration, here expressed in weight percent. The activity of nitrogen is defined as equal to its weight percent in the binary Fe-N solution at any temperature. Its activity coefficient in any alloy is the comparison being made at equal values of T and PN2. In all alloys the activity coefficient changes with composition, log fN being a linear function of the percent of alloying element at low concentrations. In the following calculations the alloy compositions are restricted to those in which this linear relation is exhibited. For most systems this is a fairly wide range, for example up to 5 pct V and to 10 pct Cr or Ni. For this composition range. complex alloy is the same as that in the Fe-N-j ternary solution. Langenberg's method of prediction was based on Eq. [3], the values of log fN for various additions being taken from a graph. Instead of using the simple addition indicated in Eq. [3], he used a more complex method suggested for Fe-S-j alloys by Morris and Buehl.3 For the composition ranges in which Eq. [2] is valid the two methods are equivalent. Nelson extended the prediction to other temperatures on the assumption that logfN is inversely proportional to absolute temperature. It may be shown that inverse proportionality would result if the partial molal entropy of nitrogen were unaffected by addition of the alloy element, an assumption which Nelson designated as a "regular" solution. It has been shown recently by the authors4 that this assumption is not a good approximation. The heat of solution of nitrogen (N2) in an alloy may be obtained if the solubility is known as a function of temperature. Measurements of this nature have been reported recently by Beer5 for Fe-Mn alloys, by Nelsson2 for Fe-C, by El Tayeb and parlee6 for Fe-V, and by Pehlke and Elliott7 for many alloys embracing a wide range of compositions. In connection with the work of the last named authors it is noted that their Fig. 22 gives the heat effect per half mole rather than per mole of N2. In using their data we have shifted some of their values slightly by using the best straight line in preference to their curve. Their data, supplemented by others from the literature, are summarized in Table I. In Fig. 1 the heat of solution of nitrogen is shown as a function of composition for the several alloy systems. The difference between the heat effect in the alloy. AH; and that in pure

Jan 1, 1965

By R. L. Loofbourow, Roger V. Pierce

THE degree to which our mineral requirements are being met by mining leaner, more complex or more remote deposits is indicated by developments during 1953. Heavy capital investment, skilled technical advice, planning, and able execution are requirements for the typical venture. Producers, faced with rising costs and with softer prices, are seeking improved mining and recovery. Developments in production of iron ore are typical of the course being followed in metal and nonmetal mining. Iron ore development in the U. S. is concentrated on the spectacular work with Lake Superior taconite, while in Canada new production is expected from Labrador and output from Steep Rock, Algoma, and Newfoundland is being increased. Shipment of iron will soon be made from Venezuela.

Jan 2, 1954

In 1970, the federal Clean Air Act was passed, promulgating limits on the emissions of sulfur dioxide (SO2) from large stationary sources that would affect local air quality. The brunt of this regulation was felt by the electric utility industry, especially those units generating electricity with coal-fired boilers. The law hastened development of a new industry, flue gas desulfurization (FGD), which is composed of three major segments: the electric utility, the FGD equipment suppliers (the scrubbing modules), and the scrubbing chemical suppliers. Dravo's experience suggested the equipment end of the business, but market analysis recommended investigating the chemical processes involved in the removal of the SO2 gas. This resulted in the formation of Dravo Lime Co. to manufacture and market reagents to the FGD industry. This paper will briefly describe the Thiosorbic lime scrubbing process and review Dravo's innovative mine and calcining facility.

Jan 1, 1982

By W. D. Ludemann, J. E. Dor, L. A. Shepard

Recovery of the creep resistance of 99.99 pct pure Al was studied at temperatures 540°, 573°, 600°, and 611°K. Poly-crystalline specimens crept under a stress of 950 psi to a strain of 5.5 pct were allowed to recover for periods of from 1 min to 16 days under a residual stress of 4.4 psi. Increased creep rates upon reapplication of the 950 psi stress evidenced softening of the material. The activation energy for the recovery process was found to be 64,000 cal-per mol. THREE major observations have clearly revealed that the creep of polycrystalline aluminum above about 510°K is controlled by the rate of climb of jogged edge components of dislocations past the barriers impeding their motion: 1) Extensive polygonization, characteristic of climb, takes place during creep.'9' 2) The activation energy for creep equals the estimated activation for self-diffusion. 3) The stress law for creep coincides with theoretical predictions based on the climb mechanism.4,5 The decreasing rate during the primary stage of creep must be ascribed to the introduction of additional barriers to the glide of dislocations. During secondary creep the density of barriers must remain constant, the rate at which new barriers are formed being equal to the rate at which they recover. For this reason the nature of the barriers, and their rates of formation and recovery, are significant to a complete understanding of creep. It is proposed here to study the kinetics of the recovery of barriers to creep of high-purity polycrystalline aluminum in the climb range. The technique will consist of creeping a series of tensile specimens under a prescribed stress to given state following which the specimens will be recovered for various times and temperatures under approximately zero stress. The amount of recovery will be determined by comparing creep curves following the recovery. EXPERIMENTAL PROCEDURE The material used for this investigation was a 99.99 pct pure Al supplied by the Aluminum Co. of America in sheets of 0.001-in. thickness having an H-18 temper. The spectroscopic analysis of impurities gave Cu-0.004 wt pct, Fe-0.002 pct, Si-0.001 pct, others-0.000 pct. Creep specimens were machined with their tensile axes in the rolling direction of the sheets. Annealing in a molten potassium nitrate-potassium nitrite bath for 1 hr at 686K, followed by air-cooling, resulted in a grain diameter of from 0.22 to 0.27 mm. Creep machines were equipped with constant stress lever arms of the type suggested by Fullman, Carreker, and Fishher,' which maintained the applied stress to within 0.04 pct of the reported value of 950 psi. Creep strains were calculated from extensions over a 6-in. gage section to the nearest 3 X 10"5. The temperatures of testing, 540°, 573", 600°, and 611°K, were obtained by immersing the specimen and extensometer assembly in a molten KNO2-KNO3 bath. Temperatures during the periods of creeping could be maintained constant to within better than ± 1°K. Correlation of creep data at different temperatures of testing demanded the use of an appropriate temperature-compensated time 8. Previous investigations have shown that the creep of pure metals at temperatures above about 0.55 of their melting temperatures can be correlated by the functional relationship3" e=f(0), s= const. [1] where e = total plastic strain during creep f = a function that depends on stress a = stress 6 = te-Q/RT = a temperature-compensated time t = time under test Q = 35,500 cal per mol = activation energy for creep R = gas constant, and T = absolute temperature In the present series of tests all of the creep was conducted under the same stress of 950 psi. To provide identical initial conditions for the recovery all specimens were first crept to a temperature-compensated time of = 47 X 10-14 min which resulted in a creep strain of 0.055 + 0.005 regardless of the creep temperature. During recovery, a small stress (4.4 psi) was permitted to remain upon the specimens to maintain tautness in the pulling assembly and to prevent mechanical damage to the soft specimen. After each recovery period, the full stress was reapplied and

Jan 1, 1961

By F. D. George, M. J. Salkind

Al3Ni whisker-reinforced aluminum was found to exhibit good Charpy impact toughness and little notch sensitivity even though its room-temperature tensile elongation parallel to the whiskers is only 2 pct. This impact behavior was maintained d liquid nitrogen temperature (-196"C). It is postulated that this behavior is due primarily to the presence of the continuous aluminum matrix which provides sufficient 10calized ductility in the vicinity of the crack tip to absorb considerable energy from the advancing crack. The impact behavior of Al-Alni was found to be quite anisotropic. Of six orientations studied, the transverse orientation having the notch normal to the whisker axis was found to exhibit the lowest impact energy, whereas the transverse orientation having the notch parallel to the whisker axis was found to exhibit the highest impact energy. A significant differnce was noted between the impact behavior of material containing needlelike whiskers and that containing bladelike whiskers. Only two of the six orientations studied exhibited complete fracture for the material containing needlelike whiskers. On the other had, most of the specimens containing bladelike whiskers exhibited complete fracture. It was postulated that the bladelike whiskers block transverse flow, thus reducing the amount of plastic deformation ahead of the crack tip. One of the more significant advantages of composite materials is the prospect of combining high strength with toughness. In general, toughness is associated with materials which exhibit considerable ductility and can deform plastically in the presence of a stress concentration. Very strong materials which resist plastic deformation generally exhibit low toughness. At first glance, then, it would appear as though strength and toughness are mutually incompatible so that useful engineering materials would have to be a compromise between the two. One approach to the problem of combining the high intrinsic strength of ceramics with the toughness of metals was to mix them together to form a cermet. Unfortunately, the toughness of cermets was found to be rather disappointing. Whisker reinforcement of metals, however, appears to be a more promising approach. It has been demonstrated that whisker-reinforced metals produced by unidirectional solidification exhibit enhanced strength due to the presence of high strength nonmetallic whiskers. The total strain capacity of these composites in the direction of fiber alignment is limited to that of the fibers, the matrix being unable to carry the load once the fibers have failed. A characteristic, then, of whisker composites is low ductility in the direction of whisker alignment, on the order of a few percent elongation. This low elongation, which is usually associated with brittle behavior, should not be taken as an indication of low toughness. Such a material can exhibit significant ductility in directions other than parallel to the fibers7 and can therefore possess significant intrinsic toughness. Toughness in a fiber-reinforced metal is derived from several mechanisms. The first is due to the toughness of the matrix itself. A continuous ductile metal matrix can act as an effective crack arrest medium by undergoing localized plastic deformation. Cracks initiated from the surface of the composite or from a brittle fiber failure must travel through the matrix before reaching another brittle phase particle. A second crack arrest mechanism peculiar to fiber composites is due to the fact that, as a crack travels through the matrix and approaches a fiber, the plastic deformation ahead of the crack tip will result in loading of the fiber. This causes the matrix shear strength in the plastic zone to be apparently higher, thus extracting more energy from the crack and diverting the crack at an angle to the original direction of propagation. A third crack arrest mechanism occurs in fiber composites which exhibit a weak bond between fiber and matrix. The idea was proposed by Cook and Gordons that if a crack propagating transversely in a fiber composite were made to turn and run along the fibers by decohesion of the fiber-matrix bond, then toughness would be imparted by the blunting of the crack tip and the creation of new surfaces. The last mechanism, interfacial decohesion, is commonly noted in naturally occurring fiber composites such as wood, bone, and bamboo, and has been observed in man-made composites such as glass fiber-reinforced resins,g silica fiber-reinforced aluminum," laminated steel," and tungsten and silica fiber-reinforced electroplated copper.'' The first mechanism, crack arrest by plastic deformation in the matrix, has been noted in tungsten wire reinforced cast copper." The purpose of this investigation was to quantitatively assess the toughness of a whisker-reinforced metal as a function of orientation. Previous investigation considered only cracks propagating nominally perpendicular to the reinforcement. In this investigation, crack propagation in three mutually perpendicular directions as well as three intermediate orientations was investigated. The system chosen for study was the unidirectionally solidified A1-A13Ni eu-tectic alloy which has a microstructure consisting of 10 pct by volume of A13Ni whiskers in a matrix of aluminum This material exhibits two different kinds of whisker morphology, depending upon the rate at which it is solidified.' At low rates of solidification (less than 2 cm per hr) the whiskers are bladelike, whereas at higher rates of solidification they are

Jan 1, 1969

By Richard W. Brummett, Robert L. Dubms

Located some 180 miles east of Los Angeles in Riverside County, California, the Eagle Mountain mine supplies iron ore concentrates for the Kaiser Steel Corporation steel plant in Fontana, California, and for export to Japan. Although the deposits were first discovered in the early 1890's, no production was realized from the area until 1948 when Kaiser Steel Corporation commenced operations. A part of the large Basin and Range province, the Eagle Mountain area's geologic column comprises a thick series of metasediments resting on Precambrian gneisses and schists that have been intruded by sill-like masses of porphyritic quartz monzonite. The metasediments are composed of three quartzite units that are separated by a schistose meta-arkose and by two ore zones. They have been folded into a large east-west trending anticlinal structure that extends completely across the Eagle Mountains. The iron ore deposits occur in two well-defined horizons in the metasedimentary series, and they are found only along the north limb of the major anticline. Host rocks for the ore zones were a series of limestones and dolomites with associated quartzites. Magnetite plus pyrite comprised the primary mineralization that formed many replacement lenses and stringers of ore within the ore zones. The primary ore has been oxidized to hematite and goethite in a broad zone at higher elevations in the deposits. Hydrothermal alteration formed actinolite- tremolite granofels, local phlogopite, and minor tourmaline in the ore zones. This alteration and the ore deposition seem related to the same magmatic event that formed the porphyritic quartz monzonite intrusion

Jan 1, 1968

By B. Wilshire, W. J. Evans

W. J. Evans and 8. Wilshire SEVERAL recent investigations1-6 have shown that the strain, c, during transient and steady-state creep is well-represented by the expression: € = e0 + et(l - e-mt) + Esl [l] where Eo is the instantaneous strain on loading, ET the total transient strain, C, the steady creep rate! and m a constant relating to the rate of exhaustion of transient creep. However, it has been noted6 that deviations from this equation occur over the first 10 to 15 pct of the transient stage, when the creep rate, (. decreases more rapidly than is predicted by this equation. This rapid decrease has been attributed to a large change in work-hardening coefficient. It 1s widely accepted that steady-state creep results from a balance between the rate of strain hardcning h and the rate of recovery r (=-s(st) as: dE/dt = Es = r/h [2] Comparison of values obtained for h at the end of the initial extension and during steady creep suggests that h increases several fold during the transient stage. which has the effect of reducing the creep rate proportionally.7 To examine the dependence, on r and h, of the deformation behavior during transient and steady-state creep. a series of constant-stress creep tests was carried out at 413°C at 6000 psi using 70-30 a brass. Prelinlinary investigation showed that. with this material. the transient stage constituted a significant portion of the total creep life (-0.4tf. where tf is the time to fracture). The alloy. obtained from Metals Research Limited. was made from high-purity copper, 99.999 pct. and zinc. 99.99 pct. Heat treatment at 675°C for 4 1/2 gave a uniform grain size of 5 mm-1. Details of specimen preparation and creep testing procedures have been given previously.6 Values of h (?s/?E) were determined by measuring the instantaneous strain. ?E. which occurred on increasing the stress during creep by a small amount. ?s. Similarly. v (= -?s/ ?t) was derived from the incubation period. At, after a small decrease in stress.' Several values of v and h were obtained throughout duplicate creep tests. using different stress increments in the range 300 to 800 psi. The accuracy with which Eq. [I] represents the present creep curves was established by determining the best value of the constants Es, Et, m , and 6, using a digital computer program based essentially on the graphical solution for this equation devised by Conway and Mullikan.9 About 40 strain/time readings were taken during transient and steady-state creep. Over most of the creep curve, the average difference between the measured reading and the calculated strain at the appropriate time was less than 0.0001. However.

Jan 1, 1969

By P. A. Beck

ACCORDING to a recent hypothesis of Sully,' xY. binary CT phases are characterized by 1.7 bonding 3d electrons per atom, which completely fill the first Brillouin zone. This hypothesis appears to imply that there are no empty 3d orbitals in the u phase, and that, correspondingly, this phase must be dia-magnetic, or at most weakly paramagnetic. On the other hand, Bowen and Hoar' reported that a u phase extracted electrolytically from an alloy steel became ferromagnetic when cooled to about —113°C. In view of the fundamental interest of the problem from the point of view of the electron structure of the u phase, it seemed worthwhile to study the magnetic properties of massive u phase specimens of various known compositions. Sigma specimens of the following compositions were tested: 1—40 atomic pct Fe, 40 atomic pct Cr, and 20 atomic pct Mo 2—35 atomic pct Fe, 35 atomic pct Cr, and 30 atomic pct Mo 3—48.7 atomic pct Fe, 50.2 atomic pct Cr, and 1.1 atomic pct W 4—40.7 atomic pct Co and 59.3 atomic pct Cr All specimens were found to be strongly paramagnetic at room temperature, particularly alloy No. 1. At liquid nitrogen temperature, alloy No. 1 be- came ferromagnetic; the other u alloys remained paramagnetic. Even though apparently not all u alloys become ferromagnetic at liquid nitrogen temperature, in view of their strong paramagnetism it is probable that the electron structure proposed by Sully is not correct. Similar qualitative studies were made with the p, P, and 8 phases." A p phase specimen of 57.2 atomic pct Co and 42.8 atomic pct Mo; a P specimen of 19.9 atomic pct Cr, 37.8 atomic pct Ni, and 42.3 atomic pct Mo; and a 8 specimen of 50.4 atomic pct Ni and 49.6 atomic pct Mo were tested at room temperature, and all were found to be paramagnetic, although considerably weaker than the u phase specimens described above. A test at liquid nitrogen temperature gave similar results for all specimens; none became ferromagnetic. Thanks are due to D. K. Das for preparing several of the alloys and to Pol Duwez of California Institute of Technology for kindly loaning four specimens of cr alloys. References 1 A. H. Sully: The Sigma Phase in Binary Alloys of the Transition Elements. Journal Inst. Metals (1951) 80, p. 173. - K. W. J. Bowen and T. P. Hoar: Low Temperature Ferromagnetism of Sigma Phase in an Alloy Steel. Research (1950) 3, p. 484. 3 S. Rideout, W. D. Manly, E. L. Kamen, B. S. Lement, and P. A. Beck: Intermediate Phases in Ternary Alloy Systems of Transition Elements. Trans. AIME (1951) 191, p. 872; Journal of Metals (October 1951).

Jan 1, 1953

By J. R. Dunn

Planning quarry operations and control of the quality of rock materials at Hudson Cement Co. at East Kingston, N. Y., are special problems because of multiple uses for the stone and the great structural complexity of the rocks. Problems have been largely solved by detailed geologic work. These geologic studies have paid dividends in long and short range planning, in assessment of reserves, in vastly reduced cost of chemical analyses, and in reduced drilling costs. Limestones of the Hudson Valley outcrop along the Hudson River from Albany to Kingston. Old established cement companies are located just south of Catskill and just east and southeast of Hudson, N. Y. The new Atlantic Cement plant is being constructed at Ravena. Hudson Cement located at East Kingston, is a newcomer and is closest to the New York metropolitan area (Plate I).

Jan 11, 1961

By Charles White Merrill

Mankind's progress is measured in minerals. Man's emergence from prehistory is marked by passage through a Stone Age and a Bronze Age and into the present era, sometimes called the Iron Age or the Age of Metals. With the evolution of civilization and the development of a modem industrial economy, minerals become more and more important. Structures, roads, and machines are built largely of minerals; the energy to heat the structures and to drive the machines is mostly mineral; agricultural fertility is maintained by mineral fertilizers and water; and military strength is provided by fortresses, armaments, and munitions, largely of mineral origin. Thus in the material world, in the productivity of the economy, access to minerals has paramount importance. Every evidence indicates increasing dependence on minerals in the modem economy, particularly on the mineral fuels as energy sources to provide the power base for advancing industrialization. Both the total and the per capita consumption of almost every mineral is increasing in the industrialized nations. Moreover, nations with predominantly agrarian economies call themselves underdeveloped and universally strive to industrialize. Most mineral consumption trends in the more advanced economies have been greatly exceeding population growth-which itself has been advancing at an accelerating rate--and sometimes have surpassed the growth in real income. Some minerals have only recently been adopted or grown to importance in use. Titanium as a metal appeared as a commercial product only in 1948, and even coal seriously displaced wood as a source of heat less than two centuries ago. On the other hand, minerals have always played an important role in construction. The prehistoric megaliths that form the dolmens of Salisbury Plain are stone; the pyramids are andesite faced with limestone; and many other ancient structures are built of mineral materials. In modem times the whole course of architecture has been redirected by new building materials, mostly mineral. Most conspicuous is the sky-

Jan 1, 1959

By Evans B. Mayo

This study examines the structural framework of the Southwest for evidence of the four principal trends of lineament tectonics. It attempts to classify their intersections and compares the positions of those trends that appear most favorable with the positions of the presently known mining districts. This is a controversial topic. The author, in presenting his analysis, is aware that the study of lineament tectonics and relation of ore districts to regional structure is complicated by insufficient data and, unavoidably, by personal bias. The development of lineament tectonics has been summarized by Umbgrove.' Early attempts to fit ore districts into the Cordilleran framework were made by Billingsley and Locke, who do not refer to lineament tectonics, although their appoach is similar; they observe that heat and fluids, including the ore-depositing fluids, are most likely to rise at or near intersections of major structures where the crust is fractured, or weakened, to great depth. As a result of studies distributed over the earth-including ocean basins as well as continents— some tectonists recognize four dominant structural trends: 1) northwest; 2) northeast; 3) nearly east-west, or equatorial; and 4) nearly north-south, or meridional. Baker' proposed a theory to account for these trends and Sonder" called their world-wide arrangement the regmatic shear pattern. Moody and Hill proposed a much more complicated shear network which, although fascinating and perhaps ultimately useful, will not be followed here. In a recent review of deformation within the Cordillera, Wisser mentioned the four fundamental directions. The fact that many geologists deny the existence of the regmatic shear pattern implies that the fundamental structures are far from obvious. It may mean, also, that some geologists are not accustomed to examine regional and world maps analytically. The maps require much study, and certain features should be isolated on overlays. Even so, with the present limited knowledge, uncertainties remain. The following analysis is a qualitative experiment, subject to change as information accumulates, and should be supplemented by the western sheet of the Tectonic Map of the United States.' Many have probably gained the impression that the Cordillera of the West is oriented northwest-southeast and from this, unless experience rules otherwise, it is natural to assume that the structure likewise trends northwest-southeast. To an important extent this is true, yet anyone tracing off the western sheet of the Tectonic Map all the recorded north west-southeast structures may be surprised to see what a small part of the entire area they occupy. In southwestern U. S. (Fig. 1) the northwest-southeast structures are mostly restricted to the eastern, southern, and western parts. The eastern margin of the Cordillera from northern Colorado to the International Boundary near El Paso, Tex., is obviously determined by some structure other than northwesterly ones. In eastern Nevada and far southward toward the Gulf of California many mountain ranges, valleys, and faults are meridional. In the Rocky Mts. of Colorado, and at many places in southern Arizona, the crystalline Pre-Cambrian is foliated northeast-southwest. The Uinta Mts. of Utah trend approximately east-west, in much the same way as a broad belt of transverse, west-northwest structures—the Texas lineament of Hill",' and Ransome10 in southern Arizona, southwestern New Mexico, and southern California. It seems, then that there are four regmatic shear directions in the Southwest, but at many places they are discontinuous, and their projections must be inferred. To clarify these trends the four sets have been isolated into two systems: 1) northwest-northeast and 2) east-west-north-south (Figs. 2 and 3). Northwest-Northeast System: A number of prominent northwest-trending zones of structure are easily recognized. They are designated by circled Roman numerals, the northeast-trending structures by circled capital letters. Perhaps no two geologists would agree completely on the positions of all these belts. Names given below are for convenience only, and may be discarded where other names have priority. (I) The Sierra Nevada-Lower California belt contains the Jurassic-Cretaceous granitic massifs of the Sierra Nevada and Lower California. These

Jan 1, 1959

By AIME AIME

BY the end of 1943, the United States will be able to produce aluminum at a rate of 1,150,000 tons a year. How much aluminum is 1,150,000 tons? It is sufficient to replace every railroad passenger car in this country three times a year. Or, it would put a thirty-piece aluminum cooking utensil set in every one of America's 34,000,000 homes with enough metal left over to make 5,000,000 miles of aluminum transmission cable, such as was used in the electrification of much of rural America. Expansion of aluminum production capacity for the war program has occurred in three steps: (1) expansion by private industry; (2) the letting of contracts by the Defense Plant Corp. for the construction of additional aluminum plants which may remain after the war to compete with existing facilities; and (3) the more recently announced D.P.C. program for the building of emergency plants to make aluminum, using stand-by power available in large metropolitan centers power of relatively higher cost, making it questionable whether such plants, now gravely needed, will be able to compete in a peacetime economy.

Jan 1, 1943

By M. E. Fine

IN the apparatus for measuring internal friction shown in fig. 1, a modification of that described by Kê,1,2 the parasitic energy loss or background is equivalent to a Q-1 of approximately 4x10-5. This low value of background was obtained by using a jeweler's collet of appropriate size for the upper support, eliminating lateral motion without immersing the bob in oil, and designing the bob to reduce air resistance. The pendulum is supported on the frame through a snug fitting, sliding rotary joint (fig. I-B). A slight twist of the top imparts essentially pure torsional motion to the pendulum. No evidence of energy loss in the sliding joint has been observed. In the bob (E) steel balls are used in the torsion arm, and the bottom is filled with lead giving a total weight of 94 g. A lighter bob may be used for small diameter specimens. Another bob was a solid disc with provision for adding discs to change the frequency. The oscillating image of the filament is recorded on a revolving drum camera (fig. 1-3) driven by a synchronous motor. This allows use of frequencies higher than can be measured visually on a glass scale. Samples varying in diameter from 0.020 to 0.075 in. have been measured, the frequencies have ranged from 1 to 12 cps, and the maximum strain varied from 0.5 to 10x10-5. With appropriate modification the sample may be placed in a thermostat. The apparatus may also be used to measure the shear modulus. In the examples of measurement given in table I the internal friction of Permendur and the 46.8 Ni-Fe alloy are due, for the most part, to magneto-mechanical hysteresis8 (elastic hysteresis accompanying stress-induced magnetostriction) which depends on strain amplitude and increases with annealing. The internal friction of most materials decreases with annealing. References IT. S. K6: Physics Review (1947) 71, 533. 2 T. S. Kê: Transactions AIME (1948) 176, 448; Metals Technology (June 1948) TP 23703. 3 R. Becker and W. Döring: Ferromagnetismus. 365 (1939). J. Springer.

Jan 1, 1951

By C. R. Claus, G. A. Standish

Since March. 1945, the Magnolia Petroleum CO. has drilled 39 wells in Southwest Coastal Louisiana. All wells were drilled within a comparatively small radius, but the area provides a large variety of problems. The deepest well drilled was 13,518 ft, and the total depth averaged 10,977 ft. Throughout this period drilling mud control and types of mud handled were: (I) phosphate, (2) red lime (late conversion), (3) red lime starch (early conversion), (4) red lime starch oil emulsion, (5) precision controlled low alkalinity-low lime content. and (6) gel muds for completion purposes. Improvement has been obtained in effecting some or all of the following: (I) more rapid penetration, (2) reduction in drilling hazards, (3) better evaluation of cores and logs, and (4) better completions. The geological sequence of zones penetrated range from recent sediments at the grass roots through the Frio section. Anticipation of high-pressure zones and incompetent formations entails precision control of drilling mud weights, and the unconsolidated nature of the various zones requires constant attention to the filtrate, viscosity, and gel strength values. In the Chalkley field, particularly, this combination of problems exists, where the formation pressures and overburden weight density values are in very close proximity. Design of casing and drilling mud programs must be modified to fit each well. INTRODUCTION Field and research work on drilling fluids has made constant progress, enabling operators to prospect progressively deeper horizons. Numerous papers have been written on the theoretical aspects of drilling fluid devel- opment, but in the field engineers have found it difficult to evaluate the role of specific mud constitutents when dealing in terms of thousand barrel mud systems. For that reason field data is somewhat lagging in technical report writing. However, applications of new techniques in the field have usually paralleled, and in numerous instances preceded, research work. The information obtained by Magnolia Petroleum Co. in the course of drilling 39 wells within a comparatively small area in Southwest Coastal Louisiana provides an excellent opportunity of reviewing a specific example of drilling mud evolution. A large variety of problems has been coped with, the most important result being that every well was successfully drilled to its projected total depth. The discussion begins with the advent of deep drilling in this area in March, 1945, and is concluded with a resume of recent drilling operations in the Chalkley field. The primary purpose of this paper is to describe the evolution in types of drilling fluids as it occurred and its application in the solution of various drilling problems. All of this information and experience resulted in the successful drilling of the three wells in the Chalkley field, where a combination of the most sound techniques was necessary in carrying drilling operations to the projected total depths. Other operators along with service company engineers have contributed considerably through the interchange of ideas and information to this paper, but the data and conclusions which are contained are based on first-hand observation of Magnolia Petroleum Company's drilling operations. The 39 wells drilled by Magnolia Petroleum Co. average in depth 10,977 ft per well, while the maximum depth penetrated was 13,518 ft. The cost of drilling fluids have varied from $8,700 to $165,000, with the over-all drilling costs ranging from $74,000 to $543,000 per well. This wide variance illustrates the unpredictable nature of each well and the effects on over-all cost when high density muds are required to control

Jan 1, 1955

By NEWTON B. KNOX

THE war has forced the principal industrial nations of the' world into the strait jacket of a closely controlled economy; taxes have been heaped upon all enterprises in order to maintain the armed forces and to deprive the people of the ability to bid for goods now unavailable. These restrictions, controls, and taxes are unlikely to disappear entirely after the war has been won, for debts will remain to be paid with a long period of difficult readjustment. Although the new economy will doubtless offer plentiful opportunities for the advantageous use of capital, no investor can ignore the favorable conditions offered by industry in Latin America, where taxes are relatively low and the restrictions on free enterprise comparatively mild. In mining in South America, the great international corporations have

Jan 1, 1944