Search Documents

By Frederick Burbridge

The Morning silver-lead-zinc mine of the Federal Mining & Smelting Co. is about 'two miles northwest of Mullan, Ida. The lode is a metasomatic fissure vein. The orebody is approximately 2000 ft. long within the bounds of the property and varies in width from knife edge stringers to 50 ft. It has been developed to a depth of 3600 ft. and stands nearly vertical in Revett quartzite, which .strikes north 65" west. The high-grade veins and lenses are generally mixed with waste (siderite, quartz, and quartzite). The average grade of ore to sorting plant in 1921 was 4 oz. silver per ton, 8.6 per cent. lead, and 4.1 per cent. zinc. Wall rock stands only a short time without timbering. The minimum angle of gravity flow is 45". The ratio of waste sorted out to ore is 6 per cent. No gases are generated underground and temperature has no influence on mining operations. Fresh air is forced down the air raise and up the main shaft. Drifting and Stoping Main drifts 12 ft. wide and 13 ft. high are driven every 200 ft. (vertically) and are connected by raises 125 ft. apart. These raises consist of three compartments (chute, tramway, and timber slide) and are for the purpose of ventilation, access, and hoisting supplies to stopes. Ground is stoped between raises. Chutes are placed every 25 ft. for drawing off ore broken in stopes. Waste for filling is obtained from waste raises off the stope in walls or waste is dumped from the level above down the chute compartment of raises, which is bulkheaded so that waste can be drawn off at any floor as required. Timbering Posts and caps for square sets (varying in diameter from 6 to 24 in.) are cut to length in a sawmill on the surface. No preseratives are used. Timber is taken on a flat car along drifts to a raise nearest the working place and hoisted as required. Practically no timber is salvaged for

Jan 1, 1925

By D. A. Farmen

INTRODUCTION In early 1978, engineering personnel at The Carter Mining Company began using photogrammetry coupled with a computer modeling technique to aid in mine planning efforts. The decision to develop this approach was based on the following needs: 1. A method to accurately capture excavated quantities for reporting purposes, 2. A method to produce accurate up-to-date maps for planning purposes, and 3. A computer-based mine-planning technique that would be compatible with techniques used in the past. The system developed utilizes a photogrammetric contractor to provide thousands of aerially-surveyed data points for input into the computer system. Each month the Rawhide and Caballo mines are flown by the photogrammetric contractor. The terrain of the active pit area is digitized and punched out on computer cards. This information is read into The Carter Mining Company's computer facilities, and an updated two-dimensional topographic grid model of the pit is generated. This surface is used to generate quantities moved during the month, to update isopachs, and to update quantities contained in fixed block progression polygons used for forecasting purposes. The system has greatly reduced the amount of manhours spent in field surveying and provides a useful tool for expeditiously evaluating many different forecast cases. It also provides the

Jan 1, 1983

By H. S. Drinker

THE first discovery of zinc 011 the property now worked by this company was made by the celebrated mineralogist, Prof. William Theodore Rapper, in 1845. Different claimants kept the property in continual litigation till 1861, when everything was satisfactorily settled by the purchase of the land by the company, who have worked it ever since. The mines are situated in a valley, four miles south of Bethlehem, Pa., in Lehigh County. The valley is from two to three miles broad, and is bounded 011 the north and south by syenitic hills. Syenite underlies the valley, and upon this is deposited the Potsdam sandstone, then a layer of slate, and, finally, a dolomitic limestone, belonging to the Chazy or Black River formation, in which the zinc deposits are inclosed. The rocks occur in folds, and have evidently been subjected to tremendous pressure from below, the zinc deposit being found in an anticlinal axis, in nearly vertical veins. I t is supposed that the zinc was originally disseminated through the

Jan 1, 1935

By J. Van Steveninck, A. C. Pols, R. Feenstra

In the course of time, an increasing number of investigations on jet cutting all kinds of material, such as rock,1,2,3 metal,4,5 and wood6 have been reported to serve various applications. A number of papers have been published on these subject, 7,8,9 some of which refer to jets purposely containing abrasives, termed 'jetted particle drilling'.7 Since such abrasives complicate fluid handling considerably and do not appear to be absolutely necessary for making holes, only conventional drilling fluids have been considered. A large part of our investigation has been performed with the aid of three laboratory-type drilling machines, which permit tests on both micro-bits (1 ½ in. ) and full-scale bits (6 ½ -9 5/8 in. ) . In view of the application of jets in deep holes, care has been taken to simulate hydrostatic pressures as they exist in the field on the hole bottom. These have been found to have a major effect on the bit-penetration rate for various drilling fluids.

Jan 6, 1974

Jan 1, 1912

By L. R. Gremillion, G. H. McClellan

Chemical and mineralogical data on 25 apatitic phosphate ores of diverse origins from commerical deposits around the world were widely variable. From 14 to 18 chemical constituents of each sample were determined, and each sample contained four to ten mineral phases. Altogether there were 34 different mineral phases, many of which occurred in only one sample. Samples contained varieties of francolites, fluorapatites, and mixed hydroxyfluorapatites. The apatite compositions calculated from chemical data showed that certain types of substitutions were characteristic of different apatite varieties, but every variety had some degree of substitution of (CO3)2- for (PO4)3-, and the P205 contents of the apatites ranged from 35.1 %for a North Carolina apatite to 41.9% for a Missouri apatite. In a concentrate with a grade of 32% P2O5, the North Carolina sample should contain about 8.7% gangue and the Missouri sample about 23.7% gangue. To optimize the digestion process of a phosphate ore, it is necessary to consider the dissolution behaviors of different mineral phases during acidulation and their possible effects on chemical properties of a fertilizer intermediate. In the production of wet-process acids or superphosphates, acidulation of certain minerals may cause foaming and formation of sludge, filtration, corrosion, and handling problems.

Jan 1, 1982

The Library is a cooperative activity of the American Institute of Mining and Metallurgical Engineers, the American Society of Civil Engineers, the American Institute of Electrical Engineers and the American Society of Mechanical Engineers. It is administered as a public reference library of engineering and the allied sciences. It contains 133,000 volumes and pamphlets, 6700 maps and receives currently most of the important periodicals in its field. In order to place the resources of the Library at the disposal of those unable to visit it in person, the Library is prepared to furnish lists of references to engineering subjects, copies or translations of articles, and similar assistance. Charges sufficient to cover the cost of this work are made.

Jan 1, 1933

By F. S. Pettit

The oxidation of Ni-3 to 25 wt pd Al alloys has been studied in 0. 1 atm of oxygen at temperatures between 900° and 1300°C. These alloys have been found to oxidize by three different mechanisms which depend on the temperature of- oxidation and the alloy composition. Two of the three mechanisms do not permit a continuous layer of Al,0, to be formed on the alloy surface and the oxidation rates are greater than that for pure nickel. The third mechanism results in the formation of an external A1203 scale and lke oxidation rates are about three orders of magnitude smaller than those for pure nickel. The minimum amount of aluminum required for the formation of external scales of A L,0, has been determined. NICKEL-base alloys are currently the main source of materials for use at elevated temperatures in gas turbine engines. These alloys are usually coated to obtain oxidation resistance. Coatings on nickel-base alloys are frequently formed by reaction of the alloy with aluminum whereby alloyed nickel aluminides are formed. The alloyed nickel aluminides provide protection to the nickel base alloy because external scales of A1203 (alumina) are formed during oxidation and mass transport through A120, is slow in comparison to mass transport through most other oxides. In view of the protective properties of A1203, it is important to know how much aluminum is required in these alloys in order to form external scales of AlzO,. The present paper is concerned with the oxidation kinetics and the oxidation mechanisms of Ni-A1 alloys and the minimum amount of aluminum required in these alloys for the formation of external scales of Alz03. THEORETICAL CONSIDERATIONS When a Ni-A1 alloy is heated in oxygen at elevated temperatures, the following reactions can take place on the surface of the alloy where the oxide phases are assumed to be virtually pure: These oxide phases are in the form of nuclei scattered over the surface of the alloy and, in view of their rapid formation, they need not be in equilibrium with the alloy. As the oxidation process continues, equilibrium between the alloy surface and the oxide phases is approached and the stability of the oxide nuclei is determined by the composition of the alloy at the alloy/oxide interface because of the following reactions: 3NiA1204 + 2A1 (alloy) = 4AlzO3 + 3Ni (alloy) [41 4Ni0 + 2Al (alloy) = NiA120, + 3Ni (alloy) [ 5 1 Application of the mass-action law to Eqs. [4J and [5J yields the following equilibrium conditions for these reactions: where aA1 and aNi are the activities of aluminum and nickel, are the standard free energies of formation of NiO, A1203, and NA1204, respectively, R is the gas constant, and T is the absolute temperature. If the composition of the alloy at the alloy/oxide interface is such that (akl/ahi) is greater than the equilibrium values defined by Eqs. [6] and [7], then Reactions (41 and [5] will go to the right as written. Conversely, if the alloy composition is such that the activity ratio (aLl,/aki) at the alloy/oxide interface is less than the equilibrium values, then Reactions [4] and [5] will proceed to the left. The equilibrium activity ratios in Eqs. [6] and 171 can be calculated since values for the standard free energies of formation of the oxide phases are available. Standard free energies of formation for NiO and A1203 have been tabulated by Elliott and ~leiser.' The standard free energy of formation for NiA1204 can be obtained from the data of Tretjakow and Schmalzried.' The results of these calculations are tabulated in Table I. Table I shows that the following inequality is valid over the temperature interval 900" to 1300°C: (Reaction [5]) (Reaction [4]) « 1and therefore the aluminum activity for these compositions can be taken as equal to the square root of the activity ratios (i.e., aNi = 1). If equilibrium is estab-

Jan 1, 1968

By W. R. Johnson

In the spring of 1935 the writers undertook to compare the geomagnetic and direct-current earth-resistivity methods of tracing a concealed dike along its strike. As far as they are aware no such direct test has been attempted.# The area surveyed lies along United States Highway number 15 about one and one-half miles east of Chapel Hill, North Carolina, and northeast of Bolin Creek (Fig, 1). To the south of the highway is the flood plain of Bolin Crook, and to the north is a hill that rises almost to the elevation of Chapel Hill. A diabase dike, which strikes slightly west of north, out-crops in a. gully just south of the highway. Southward it has been covered by alluvium but northward outcrops again on the southeastern slope of the hill north of the highway. South of the highway the country rock is Triassic shale and sandstone, the northern limit of which is slightly north of the road. On the Geological Map of the United States I the pre-Triassic formations are shown as lower Glenarm and assigned a pre-Cambrian age. Since the ago of the Glenarm has been called into question in Pennsylvania 2, the writers prefer not to commit themselves as to the ago of these rocks further than to say that they are definitely pre-Triassic.

Jan 1, 1937

Ore deposits of commercial grade are local concentrations of great rarity when considered in relation to the area of unmineralized land surfaces, and they must therefore be considered as the products of exceptional and complex conditions. The data collected from a great number of individual deposits are sufficient to permit certain broad generalizations in regard to the conditions favorable to ore deposition which even numerous exceptions do not invalidate. The broadest general relation of ore deposits is with intrusive rocks, and while there are notable exceptions, the great majority of ore deposits have a visible or closely inferred connection with intrusive rock masses. Conditions that permit the dissipation of the ore-bearing vehicles do not permit the concentration of metals in deposits; the prime factor to consider in this connection is that structural conditions must be such as tend to concentrate and not to dissipate the ore-bearing solutions. The disadvantage of extrusive rocks is at once apparent; any metals the magma may have contained are dissipated at the surface and are lost; with the exception of tiny vugs and cracks in quickly cooled flows, no concentrations of metals are known in extrusive rocks, and the lack of confinement and quick cooling apparently do not permit extrusives to exert mineralizing effect upon the rocks with which they come in contact. The close mineralogical similarity between extrusives and intrusives, and the great difference in mineralizing power is a proof of the ease with which magmas part with their metallic content, and of the mobility of the ore-bearing vehicles in comparison with the parent magma.

Jan 1, 1932

By H. H. Podgurski, Hsun Hu

Large cryslals of high-purily iron (99.996+ pcl) cannot be obtained by the usual strain-ameal technique. Repealed phase transformation by thermal cycling prior to crilical deformation improves the capabilily of cryslal growith but fails to yield satisfactory crystals. Imperfect columnar crystals can be produced by the phase-transition method. The addition of a small amounl (0.005 wl pet) of nilrogen IT was reported'-4 that for metals of very high purity the usual procedures of the strain-anneal technique fail to produce large crystals. This was eliminates practically all the difficulties in crystal growth by the normal strain-anneal procedures. An actual example is presented, showing that most parts of a strip have been converted into a large crystal by this method. The addition of nitrogen, which can be removed from iron with less difficulty, is believed to be more desirable than carbon additions for the same purpose. thought to be due to the strong tendency for recovery in the high-purity metals: hence the critically strained matrix undergoes polygonization instead of recrystallization upon annealing for crystal growth. Talbot1,2 succeeded in overcoming this difficulty by adding 0.03 to 0.04 pct C to high-purity iron before critical deformation. followed by annealing in hydro-

Jan 1, 1965

By E. S. Greiner

STUDY of the plasticity of germanium or other semiconductor crystals affords unusual opportunities to extend our knowledge of deformation mechanisms. Crystals are available having extraordinary perfection and very high purity. They deform by slip on the systems {111} <110>,1-3 as do crystals of the simple face-centered-cubic structure. Dislocations generated in them during slip are easily revealed in the form of etch pits on either (111) or (100) surfaces.4,5 This fact alone makes possible more detailed studies of mechanisms than is usually the case with metals but, even further, the effect of deformation on their electrical conductivity is very large compared with metals. This comes about not only because the mobility of the charge carriers is reduced, as in deformed metals, but also because the number of these carriers is greatly altered. This latter effect seems closely related to the formation of both line and point imperfections during deformation and thus provides a needed tool for the study of the kinds and distributions of these imperfections. Other investigators have deformed germanium at elevated temperatures by bending,1, 6-8 compres-sion,6, 0,10 tension,2,3,6,11,12 torsion,23 and indentation." Wang and Alexander" have also reported successful indentation at room temperature. Dislocation etch pits consequent to deformation have been observed and studied.7,8,10,18,14,20 The experiments to be de- scribed here include principally the compression and the subsequent annealing of germanium with concomitant studies of etch pits, microstructures, and electrical properties. Both single crystals and heavily twinned specimens were used. Some indentation studies are included. Experimental Methods Plastic compression was effected in the apparatus shown schematically in Fig. 1. It consists of two tantalum platens contained in a helium atmosphere and so arranged that pressure can be applied by a hydraulic press. The specimen between the platens is heated by the surrounding furnace. The specimen is usually a small crystal cube about 0.30 in. on an edge. A control specimen is always inserted so, that it is subject to the same thermal cycle as the one being deformed. This serves to detect any impurity contamination that might accompany the thermal treatment. For high temperature work, where such impurity contamination often occurs, the specimens were first plated with gold whenever subsequent electrical properties were to be determined. This method" is effective in preventing significant contamination of germanium up to temperatures at least as high as 750°C, as evidenced by the constancy of the electrical conductivities of control specimens subjected to the same heat treatments. The total range of temperature used for deformation was from 375°C, the lowest at which significant flow was observed, up to 900°C. Microscopic examination was made after mechanical and chemical polishing and etching. Dislocation pits were revealed with CP-4 etchant by the tech-

Jan 1, 1958

By N. A. Ziegler

A CERTAIN amount of interest has been indicated recently in the resistance to oxidation at high temperatures of iron-aluminum alloys (rich in iron). Hautman1 published a paper in. which some interesting results are given. According to his paper, only alloys containing at least 8 per cent aluminum indicate a marked improvement in their resistance to oxidation. At about this aluminum content, however, alloys become brittle, which considerably reduces their commercial value. About two years ago the author, performed a series of experiments, the results of which are presented here. A series of iron-aluminum-carbon alloys was prepared by melting electrolytic iron, aluminum and high-carbon iron alloy in an induction vacuum furnace.2 The list of these alloys is given in Table 1. Each alloy was forged in the ordinary way to

Jan 1, 1932

By J. Parke Channing

THESE days of great industrial and social problems in America produce many suggested solutions and great changes. The practical engineer and employer of labor views these problems differently from the labor leader or the social reformer, but as never before he is sincerely interested in solving them in a way that will be just to all. The inevitable tendency of the day is toward "industrial betterment," "safety," "industrial education," "efficiency," and the many other things&apos; which have become so familiar to progressive employers. There is no longer any question that these things are worth while from both the hu¬man and economic standpoints. They "pay" in dollars and cents. The very center of final success in improving conditions and increasing the efficiency of workingmen must be the spirit of fairness and a knowledge on the part of the employer of how to deal sympathetically and intelligently with his employees. Every progressive employer knows how greatly he desires foremen, superintendents, managers and others who possess these qualities. On the other hand, we are all familiar with serious mistakes made by young graduates of engineering schools who have had no opportunity to develop these qualities, and who have no real appreciation of the worth of the workers. Indeed, one wonders whether much ill-feeling, labor difficulties, and many strikes could not be avoided if such men had the right attitude. Is there any way of remedying this condition? If this particular difficulty can be solved, if these young engineers, many of whom are our coming leaders of industry, can be given the right perspective and the right understanding of these other problems in addition to fair, sympathetic methods of handling men, many of our other problems will be solved-not at once, but gradually and permanently, as these men make good and become influential in paths of industrial righteousness and industrial peace. Many progressive employers of to-day have enlarged their own perspective and realize the great importance of enlarging the perspective of those who shall follow them.

Jan 3, 1915

Meeting of Mar. 27, 1914.-President Thayer announced the appointment of H. S. Munroe as a member and E. Gybbon Spilsbury as Chairman of the Library Committee of the Institute. The President announced the appointment of the Committee on Papers and Publications, the Technical Committees, the Committee on Increase of Membership, and the Committee on Junior Members and Affiliated Student Societies. The President announced the appointment of Dr. George F. Kunz as a member of the Reception Committee of the International Engineering Congress, 1915. It was voted that the Institute accept the invitation of the Mining and Scientific Press to occupy space at the Panama-Pacific Exposition next to them and avail itself of the service of their representative to receive and register members of the Institute who visit this space during the exposition.

Jan 5, 1914

Edward Dyer Peters, the only child of Henry Hunter Peters and Susan Barker Thaxter, was born in Dorchester, Mass., June 1, 1849. From his father he was a descendant of the Peters family of Ipswich and Andover, Mass., whose earliest ancestor settled in Essex County in 1659; while upon his mother&apos;s side he descended from several old Hingham families, as well as from the Quineys and from Governor Bradford. Between the ages of fourteen and sixteen he was a student at the Episcopal School for boys in Cheshire, Conn. Near the school was an old tin mine, and he used to spend his Saturday afternoons exploring it. When Edward was sixteen, his father sold his property in South-borough, and for the next three years lived in Europe. Sept. 26, 1865, Edward entered the Royal School of Mines at Freiberg, Saxony. In the summer of 1867 he joined his family on Lake Geneva, and spent a part of the season in that vicinity, going to Chamounix and taking other trips. Extract from a letter to his father: Elbingerode, Harz, Aug. 30, 1868: I left Freiberg with my friend Lilienthal, on Wednesday the 19th of August, reached Leipzig in the evening and spent the night in that city: the next morning we took the cars and in the afternoon reached Eisleben, in Prussia, which was to be our first stopping-place; there are immense copper-mines and smelting-works at this place, and the method of working the mines is very peculiar ... The next morning we got up at five and spent the whole day in the smelting-works where I obtained a number of drawings of the furnaces they use here and a good many valuable data. Saturday morning we got up at four o&apos;clock, and descended a mine about three miles from the town; the Director of this mine was one of the most intelligent and agreeable men that I ever met; he accompanied us in the mine and explained everything that was new to us. The system of mining at Eisleben is peculiar to this town, and is not used at any other place in the world; the copper ore comes in narrow, flat veins eighteen inches high, at the utmost, consequently the men work lying flat on their left side and using the pick with both hands: the ore is carried out of the side passages into the main ones, in very low waggons about twelve inches high, and four by two feet; the boys who pull these waggons have a board buckled to their left thigh and their left arm; they pass their bare foot through a strap in the waggon and wriggle along on their side dragging the waggon after them, with their foot, almost as fast as a man can walk above ground. In the afternoon we walked over to Hittstadt, about twelve miles, and remained there Sunday and Monday. Monday night, at ten o&apos;clock we went out to one of the smelting-works, to see the refining of the copper; this is only done at night, so we worked there from ten in the evening till eleven the next morning, and came home all blackened up and with blistered hands, for our skin was not quite so tough as that of the workmen: at noon the same day we took the stage to Ascherls-leben, and then the train to Stassfurt, where there are immense salt-mines, as well as factories for the manufacture of bromium, which latter process is, however, kept a profound secret, so we had very little hope of seeing anything but the salt mines; we were talking with our landlord about our disappointment, that evening, when he told us that the director of the Bromium works was sitting in the next room with no company but his glass of beer, so we went over to him, introduced ourselves as Americans, and actually succeeded in persuading him that it could do his business no earthly hurt if he showed us his works; at last he consented, after making us give our word of honor

Jan 1, 1919

By S. S. Clarke

THE opening of sheet-ground mines in which the ore beds are only from 7 to 9 ft. thick led the Commerce Mining and Royalty Co. to con-sider mechanical loading, in order to avoid the high cost of hand shovel-ing in such mines. Scraper loaders were chosen because the capital investment would be comparatively low; because they are small enough to be used in low working faces, and because they can be mounted on a mobile carrier.

Jan 1, 1939

By J. M. McDowell

A study has been made to deter~r~irre how the behavior of a water drivee reservoir changes as a function of the permeability of the formation and as a function of the size of the aquifer. The effect of pressure maintenance programs on the rote of nat11rn1 water influx is also studied, (IS well as the influence on the influx of the position of water injection we1ls with reference to the oil-water contact. The results are determined by the use of an electrical reservoir analyzer and are plotted as families of curves of pressure, natural water influx, and water injection vs time or cumulalive production. Two size aquifers are studided. One is limited with a 36-inile radius, and the, other approximates an infinite reservoir. The field remains the same in all respects for the completed. study except that the permeability is changed to agree with that assumed for the aquifer. 1 N TR ODUCTI ON this study was undertaken in -dcr to determine how the pres- sure decline and water influx of a water drive field would change as a function of the rate of fluid withdrawals, as a function of the permeability of the formation, and as a function of the size of the aquifer. The effect of pressure maintenance programs on the rate of natural water influx was also studied as was the position of water injection wells with reference to the oil-water contact. The information has been determined by the use of an electrical reservoir analyzer1, sometimes referred to as a Carter type analyzer. This instrument is an analog type computer which can be set up to represent a water-drive oil field. It can reproduce the past performance of the field in terms of analogous electrical quantities when the proper circuit analog of resistors and condensers has been determined, also, it can determine the future behavior for any method of production which may be selected, or permit the comparison among several different methods. Although most applications of the reservoir analyzer"" have been to thc study of specific field performance, it is intended to use the analyzer here to help understand how various reservoir characteristics effect the final performance of the field and to sec under what conditions water injection will be of benefit and to what extent. Within the oil industry the performance of water-drive reservoirs was first described analytically by LV. Hurst&apos; and M. Muskat2 for certain types of boundary conditions. The solutions of the equations developed involved products of exponential functions and Bessel functions. Later publications by Hurst4 and van Ever-clingen" and the hooks of Muskat6 gave further information on reservoirs with other boundary conditions. They also presented rather extensive curves and tables to help evaluate the analytical expressions involved. A rccent series of publications by Chatas. bascd on the work of Hurst and van Everdingen, gives quite complete charts and tables of data to evaluate the pressure decline or water influx in infinite or limited radial reservoirs. and in linear reservoirs. The curves in all of these publications are given in dimensionless form

Jan 1, 1956

By G. A. Wells

The consumption of barytes in certain paints, polyurethane foams, seamless flooring, glass, brake linings, plastisol gaskets for food containers, and in fluids used for gastrointestinal X-ray examinations relies on the unique properties of barium sulfate. There are no readily available mineral substitutes. Barytes are also the essential raw material for the manufacture of industrially important barium chemicals. High quality barite ore has become scarce throughout the world. Processing ore into quality end products is both capital and energy intensive. These factors have tended to limit availability and increase Prices which have encouraged the use of alternative or competitive materials and restricted market growth.

Jan 1, 1981