Search Documents

By AIME AIME

AT the meeting of the Iron and Steel Division at Cleveland, Sept. 10-12, the morning of Thursday, Sept. 12, has been set aside for an excursion to visit the ore docks, blast furnaces, and steel plants. A special train, made available through the courtesy of Appleton Cleveland, general superintendent of the Pennsylvania Railroad, will leave the siding near the Auditorium at 8.35 a. m. The trip will be free, but tickets must be' obtained in advance at the booths for registration for excursions at the Auditorium. An hour will be spent at the docks, an hour at the Central blast furnaces, and two hours at the Cuyahoga works of the American Steel and Wire Co. A buffet luncheon will be served, with the compliments of the Pennsylvania Railroad Co., on board the train en route. At the Tuesday morning session, Sept. 10, a motion picture showing the operations in making wrought iron by the Aston process will be shown for the first time.

Jan 1, 1929

By William Marsh Baldwin

THE ROLLING OPERATION proper is applied to metals and alloys not only in the production of flat products but also in the production of shapes, rods, wire and even in specialized forms in the production of tubes. The present discussion of rolling copper and copper alloys will be [ ] limited to a consideration of rolling flat products such as strip, sheet, foil, plate, and others. In this case (as in the others listed above), the rolling operation itself is only part of an integrated sequence of operations. In Fig I such a sequence going to make up a brass strip mill is sketched out. It is seen that the rolling opera-

Jan 1, 1948

Jan 1, 1969

By R. E. Head

UNDER existing economic conditions, the treatment of gold ores occupies an outstanding position in metallurgical activity. The increased price of gold has automatically brought about a reclassification of old dumps and low-grade orebodies, and many that formerly were considered valueless are now being vigorously investigated and worked. This situation has developed problems that have taxed the ingenuity and ability of metallurgists to the utmost. Some gold ores give a high extraction of gold by standardized methods of treatment; other ores of apparently similar character yield but a relatively small percentage of their gold when treated by the same processes.

Jan 1, 1936

By William E. Ford, Edward Salisbury Dana

34. Axial Ratio, Axial Plane. - The crystallographic axes have been defined (Art. 22) as certain lines, usually determined by the symmetry, which are used in the description of the faces of crystals, and in the determination of their position and angular inclination. . With these objects in view, certain lengths of these axes are assumed as units to which the occurring faces are referred.

Jan 1, 1922

Jan 1, 1894

By Wilhelm Rohn

When a metal solidifies, gas, initially present in solution, may be concentrated at the grain boundaries, leading to brittleness, or it may form solid compounds which, if localized at the grain boundaries, impair the properties. On the other hand, the solid compounds formed sometimes distribute themselves more or less uniformly, and hence may be relatively harmless. If metallic oxides are heated under a partial oxygen pressure less than that corresponding to the dissociation pressure of the oxide in solution in the melt, they will decompose and oxygen will tend to be eliminated from the melt. This paper presents data on the partial oxygen pressures of copper and nickel oxides over a wide range of temperatures; it also presents data regarding the amount and nature of the gases evolved in the vacuum melting of a 3500-kg. charge of nickel-chromium alloy and gives test values indicating the improvement in impact values ascribed to vacuum melting. The results of commercial experience with a 4-ton vacuum melting and casting furnace indicate that this method entails an increase in cost of about 10 cents per pound of ingot over orthodox practice, which may be justified for special products and may be lowered if hot metal is charged into the vacuum furnace. DISCUSSION (Howard Scott presiding) J. H. ScafF, New York, N. Y. (written discussion).—In the section of Dr. Rohn's paper describing the effect of melting -metals in vacuo, he says, "In this way plain copper, nickel and iron may be easily purified. For example, vacuum-melted copper does not contain any oxygen and for this reason it is never sensitive to hydrogen embrittlement." This statement is contrary to the results of our experiments at the Bell Telephone Laboratories on the effect of vacuum melting on the properties of copper. Several 150-gram samples of tough-pitch copper were melted in a vacuum of the order of 1 X 10-5 to 1 X 10-6 mm. Hg for 2 hr. Portions of the ingots obtained were swaged to 0.100 in., then drawn to wire 0.050 in. in diameter for physical and

Jan 1, 1933

By K. P. Gupta, P. A. Beck, N. S. Rajan

By determining the a phase boundaries in the following ternary systems: V-Fe-Si (at 1175oC), V-Co-Si (at 1175°C), V-Ni-Si (at 1175oC), Cr-Mn-Si (at 1000°C), Cr-Co-Si (at 1175°C), Cr-Ni-Si (at 1175°C), V-Fe-A1 (at 1175°C) and Cr-Co-A1 (at 1175°C), it was found that Si exerts a stabilizing effect on these a phases, while A1 tends to destabilize them. Si atoms in solid solution occupy sites D in the a structure, The co/ao ratio increases with increasing Si-, Mn- or Fe-content. The volume of the unit cell decreases with increasing Si-content. THE stabilization of certain metal silicides (the Nowotny phases) by the addition of relatively small

Jan 1, 1961

Jan 1, 1923

By R. G. Hudson, H. W. Paxton

The activities of iron and chromium in their binary system have been measured by the Knudsen orifice technique. The system is close to ideal at 1200- 1250 C with slight positive deviations. The effect of this on the liquidus and solidus is discussed and these are calculated for two limiting assumptions. The vapor pressure of pure iron, pure chromium, and one alloy is compared with that obtained by the Langmuir free-evaporation technique. The results agree, indicating a vaporization coefficient close to 1. HERE are no reported data on the thermody-A namic activity of iron and chromium in the solid portions of the phase diagram. It is generally assumed'.' that the liquid solutions of iron and chromium obey Raoult's law. Chen and Chipman" have inferred that the liquid solution obeys Raoult's law. The minimum' in the solidus-liquidus curves for the iron-chromium system shows that there are deviations from ideality in either the solid or liquid or both. Because of the importance of developing reliable techniques for obtaining activity data in alloy systems at high temperatures and of the data so obtained, an investigation of the activity of iron and chromium in the binary at 1200-1250 C was undertaken using the Knudsen cell. Experimental The apparatus and experimental procedures used in this investigation were described in a previous paper." The various materials used for the construction of the Knudsen cell are listed in Table I. The metal used for the determination of the vapor pressure of chromium was 99.9 pet pure, obtained from A. D. Mackay, Inc. The iron was obtained as electrolytic grade from Fisher Scientific Company. The Fe-Cr alloys used are shown in Table 11. The largest error and controlling factor in the accuracy in the experiments reported here are introduced because of temperature uncertainty, which is estimated to be ±3 deg C. This introduces an uncertainty of 26 pet in the measured pressure. Experimental Results and Calculations The vapor pressures of pure iron and pure chromium were calculated from the measurements by the Knudsen equation3 on the assumption that only Cr or Fe atoms were present in the gas phase. For metal vapors, at the high temperatures and low pressures involved in these measurements this should be a reasonable assumption. Whitman" corrections for the cells were made. The data and results of pressure calculations are presented in Table I, and are plotted in Fig. 1. In addition the heat of vaporization at the absolute zero, ?E°°, has been calculated for chromium. These calculations are summarized in Table 111. The data used in these calculations are as follows kelley13 (F° - E°°/T ) Speiser, et al H (F° - E°°/T ) 010 where F" — standard free energy at temperature T It was necessary to calculate the total pressure above the alloys from the total weight loss W of the cell during a run, because of the fact that all attempts to collect and analyze the chromium and iron vapor effusing from the cell in the apparatus available failed. The failure resulted from the re-

Jan 1, 1959

By G. W. Jones

THIS paper describes experiments in which eight test samples of gelatin dynamite were fired in three different types of apparatus and the quantity and composition of the gaseous products of detonation determined. The special dynamites were so prepared that the oxygen balance of the samples varied from -35.0 to +6.0 g. per 100 g. of explosive, including the wrapper. By means of this graded series of explosives, the relation between oxygen balance and gaseous products of detonation could be studied explicitly. The effect of varying oxygen balance on explosive strength has been discussed in another paper.1 The apparatus employed in the work described in the present paper included (1) the Bichel gage, a steel bomb of 15-1. volume; (2) the Crawshaw-Jones confined detonation apparatus, a steel cannon from which the explosive is fired into a pipe of 90-1. volume; and (3) the Hercules tank, an apparatus in which the explosive is confined in a quartz block which is placed in a steel tank of about 4500-1. volume. A full description of the apparatus is given later. VARIABLES AFFECTING COMPOSITION OF DETONATION PRODUCTS The character of the detonation products of commercial explosives is governed in part by the same factors that affect the combustion products from explosive mixtures of air with gases or vapors. In either case, combustible materials-namely, carbon, hydrogen, and sometimes sulfur-are present and combined variously. In an exploding gas mixture the combustibles are oxidized by oxygen in the admixed air, whereas with explosives the necessary oxygen is provided by oxygen-carrying materials in the explosive ingredients.

Jan 1, 1928

By R. S. Dean

THE first attempt to establish an equilibrium diagram of the lead-antimony series was made by Roland-Gosselin1 in 1896. This investigation classified the system as a purely eutectiferous one, with the eutectic at 12.5 per cent. antimony and 228° C. In the next year, Stead2 placed the eutectic temperature at 247° C. The error in temperature made by Roland-Gosselin, however, has been perpetuated in the literature with a remarkable degree of persistency; this value was accepted by Campbell (1902), and Ewen (1910),3 and will be found in the last edition of Desch's3 Metallography (1922). Gonterman's investigation, made in 1907, was the most complete one available at the time the present investigation was started. He concluded' that the system was a simple eutectiferous one and placed the eutectic at 13 per cent. antimony and 247°C. Other investigations by Tammann (1907),5 Garbow (1909),6 Rudolfi (1910),7 Loebe (1911),8 and Leroux (1913)9 added little, if any-thing, to Gonterman's diagram. A number of investigations have been made of physical properties of the alloys. The electrical conductivity of the series was studied by Matthiessen (1860)10 and by A. W. Smith (1921);" the thermoforce by Rudolfi (1910),12 and Pelabon (1923);13 the specific heat by Durrer

Jan 2, 1926

By R. B. Muter, W. C. Grady, T. D. Wheelock, D. G. Chedgy

INTRODUCTION Topics of special interest, such as preparation plant flowsheets and noise pollution, are described in this chapter along with a discussion of non- state-of-the-art processes such as chemical cleaning, high intensity magnetic separation, and bacterial oxidation. PREPARATION PLANT FLOWSHEETS by RICHARD B. Muter In determining the layout or combination of unit operations to be utilized in a modern preparation plant several factors must be taken into account.

Jan 1, 1979

By Charles B. Dudley

DEAR SIR: It is now nearly three years since my first report to you on the subject of steel rails was written. That report, as you will remember, dealt principally with the question of the relation between the chemical composition and physical properties of steel rails end their power to resist crushing and fracture in actual service. Other matters were referred to or touched upon in that report, but the main question was, Why do some rails crush or break in service while others do not? Yon will doubtless remember that the principal conclusion arrived at was, that the softer rails are less liable to Crush or break in service than the hard ones. Or, in other words, so far as conclusions could be drawn from the chemical analysis and physical test of 25 samples of steel rails which had actually been in service, these conclusions were that those rails which have the smaller amounts of carbon, phosphorus, silicon, and manganese are less liable to crush or break in service than those which have larger amounts of these elements. Or, again, looked at in the light

Jan 1, 1881

By J. S. Ross

Few Canadians realize the role of their domestic industrial minerals industry because it is over-shadowed in production value by a large metallic minerals industry. But since 1960, Canada has had a reasonably well balanced, mature industrial minerals industry; and although the nation's sparsely scattered population has not been able to support an industrial minerals industry in a manner comparable to the domestic and foreign support given the metal mining sector, Canada is, nevertheless, exporting large quantities of higher priced nonmetallic minerals. Production of many of the basic minerals had been firmly established long before 1960, but it was not until the late 1950's that the output of cement, salt, titanium dioxide pigment and slag, sulfur, gypsum and sodium sulfate reached relatively high levels. Shortly after 1960, the significant potash and lithium chemicals industries were established and their effect is just now being realized.

Jan 11, 1964

By Rudolph G. Wuerker

MUCH descriptive matter[ ] has appeared on the subject of suspension roof supports, or roof bolting, as it is more commonly called. The wide- spread introduction of roof bolting into coal mines and metal mines is truly phenomenal. Mine operators were quick to recognize the advantages of supporting wide openings without hindrance to machine maneuverability and ventilation.

Jan 6, 1953

By R. F. Mehl

Jan 1, 1936

The discovery of nickel at the Wallace Mine in 1846, recorded in the Report of Progress of the Geological Survey of Canada, 1.848-49, was not the first find in the Sudbury mining district. As long ago as 1770 a company had been formed to work the rich deposits of, copper whose existence was then known. .But it was during the first mentioned year that, incited thereto by fresh finds and a favorable report by Mr. W. E. Logan, then Provincial Geologist, two [ ] groups of Canadians organized "The Montreal Mining Company and "The Upper Canada Mining Company." By the former company the Bruce Mines Location' was purchased and work was immediately commenced upon it. The Wallace Mine acquired by the Upper Canada Mining Company, was abandoned after a shaft had been sunk and a few test pits opened.

Jan 1, 1907

By Thomas W. Healy

Particles present in mineral processing systems that are termed ultrafine are those that are small enough to be unaffected by gravity or the flow conditions imposed on the pulp. As such, their interaction with one another and with other larger particles are controlled by specific attractive and repulsive colloidal or surface interactions. Electrostatic repulsion between ultrafines is dominated by surface potential, double layer thickness and specific adsorption potential effects - controlled by pH, salt and complexing ion concentrations. Attraction due to van der Waals interactions must be assessed in terms of bulk and surface coating effects and of particle size and shape. The net effect of attraction and repulsion must finally be related to the average kinetic energy of particles in the real system.

Jan 1, 1979

Jan 1, 1961