Search Documents

By Paul R. Cook

The ore deposit of the Buckhorn Mines Co., Buckhorn, Nev., is peculiar in being a shallow kaolinized mass of material with basalt walls, and having apparently no direct connection with any of the usual gold-bearing rocks. The average ore contains 16 per cent. water of hydration, and the cyaniding of this hydrous clayey material offered unusual difficulties as compared with an average Nevada quartz ore. The orebody was thoroughly developed; then the mill was built according to the latest cyanide practice, with such changes as were thought to be demanded by the peculiar nature of this ore. Upon starting the mill, the ore proved more difficult to handle than had been anticipated. It is hoped that an account of how these difficulties were met may prove of interest to anyone having a clayey ore to handle and to the profession in general. Geology The Buckhorn orebody lies along a north and south fault plane of perhaps 1,000 ft. dislocation, that can be traced for miles; but the only other known mineralization consists of similar ore in the Murphy mine, a mile farther north. The east or hanging wall is hard and smooth, being a typical fault plane. The best ore is along this wall, gradually grading down toward the west until at 30 to 60 ft. it is too low-grade to mine. The country rock on the west consists of alternating layers of hard and soft basalt and basalt scoria, pitching toward the mine. One of these basalt layers on the hillside a little above the mine is marked, for 3 or 4 miles in length, by a line of springs which seep out along it. Perhaps the meeting of the surface drainage, passing down these basalt layers, with the fault-plane solutions explains the formation of the Buckhorn orebody.

Jan 1, 1917

Jan 1, 1940

New York Meets first Wednesday after first Tuesday of each month: DAVID H. BROWNE, Chairman. JOHN H. JANEWAY, Vice-Chairman. F. E. PIERCE, Secretary, 35 Nassau St., New York, N. Y. P. A. MOSMAN, Treasurer. LEWIS W. FRANCIS. BENJAMIN B. LAWRENCE. Boston Meets first Monday of each winter month. HENRY L. SMYTH, Chairman. ALFRED C. LANE, Vice-Chairman. HENRY A. WENTWORTH, Secretary-Treasurer, 60 India St., Boston. Mass. A. H. EUSTIS, F. G. STANTIAL. Columbia Holds four sessions during year. Annual meeting in September or October. FRANK A. ROSS, Chairman. RUSH J. WHITE, Vice-Chairman. LYNDON K. ARMSTRONG, Secretary-Treasurer, P. O. Drawer 2154, Spokane, Wash. FREDERIC KEFFER, FRANCIS A. THOMSON.

Jan 1, 1916

By Young C. Kim, Francis Martino, Ish Chopra

For the past two and one-half years, various emission control strategies were jointly developed by the University of Arizona and the Homer City Owners to com- ply with the clean air requirements at its Homer City Power Plant. Some of the available options for the SO2 emission control by the Homer City Owners were:l)cleaning of run-of-mine coal,2) scheduling of mining operations at its captive mines, 3) blending the captive mine coal with externally purchased low sulfur coa1,and 4) placing a partial FGD system. This paper describes two specific emission control strategies developed and implemented. These are: 1) production scheduling at the mining face to minimize sulfur variability, and 2) external purchasing of low sulfur coal for further blending. The main objective of this paper is to share our experiences on implementing the developed strategies. This paper emphasizesthe need for proper mine planning on a short-term basis, if the power plant is to meet the desired objective.

Jan 1, 1983

By H. L. Riley, B. W. Gandrud

As far as the present writers know, this system of flotation has not been used elsewhere in this country, but in the last couple of years it has been introduced, with minor variations, at one plant in England and one in Wales. The system has been described and discussed in a number of publications. The following is quoted from an abstract of the latest of these," a paper presented at an International Conference on Industrial Combustion in 1952. On the basis of experience to date with the commercial plants, it is believed that the kerosene-flotation process incorporates all the necessary elements to make it greatly superior to anything else now available for treating of fines in wet processes of coal preparation. Additional study and investigation are still needed, however, to determine if certain phases of the process can be improved to such an extent as to make it generally satisfactory and acceptable to the industry. Further improvements will be needed with respect to the capacities of the flotation cells and the reagent consumption.

Nov 1, 1955

By Terry Ramsey

INTRODUCTION The Cyprus Pima Mine is located 20 miles southwest of Tucson, Arizona and about fifty miles north of the Mexican border. The Cyprus Pima orebody was discovered in 1950. Feasibility studies were begun in 1952 employing underground development. Economic studies showed open pit operations to be feasible and stripping of overburden was begun in late 1955. The first ore was reached in October of 1956. A 3,000 tpd (tons per day) concentrator was completed and began operation January 1, 1957. From these beginnings, Cyprus Pima Mining Company has expanded into a plant processing approximately 54,000 to 56,000 tpd. Four expansions were required to bring the plant up to its present capacity. Each expansion incorporated what had been learned in previous operation of the plant. The first expansion was completed in August of 1963 doubling design capacity to 6,000 tpd. In reality, because of softer than average ore, capacity was closer to 8,000 tpd. Expansion II was completed in July 1966 bringing design capacity to 18,000 tpd. Expansion III followed immediately. Completed in the summer of 1967, this expansion increased the design capacity to 30,000 tpd. The actual dry tonnage of this portion of the operation in 1974 averaged 38,400 tpd, again, primarily as the result of treating softer than average ore. The latest expansion (Expansion IV), completed in December 1971 and utilizing a semi-autoge- nous grinding circuit, is located in a separate building (Mill II) approximately 200 yards southeast of the original mill (Mill I). Expansion IV was designed for 14,000 tpd, but after circuit modifications, averaged 16,500 tpd in 1974.

Jan 1, 1976

By R. B. Mears, G. F. Sagar, R. H. Brown

There are well recognized procedures for determining the various tensile, fatigue, and other mechanical properties of the common structural materials. This makes it possible for engineers to design structures of various materials which have adequate initial strength to stand the stresses to which they are subjected in service. There is also considerable general information about protective measures suitable for protecting the usual structural materials from the effects of ordinary environments. However, often insufficient quantitative information is available on the combined effects of stress and corrosion to permit the designer satisfactorily to appraise the structure from the stress-corrosion standpoint. This situation is further complicated by the fact that the stresses causing stress¬corrosion failures are usually not the design stresses but rather the residual forming and assembly stresses which are generally of unknown magnitudes. Thus, tests which will rapidly evaluate the susceptibility of materials to stress-cor¬rosion failures are extremely useful. Of particular value are tests which can be applied to built-up structures as well as to simple specimens, since, as mentioned above, residual stresses often are caused by fabricating procedures and assembly operations. The present paper contains

Jan 1, 1945

By L. Himmel, R. F. Mehl, C. E. Birchenall

The rates of self-diffusion of iron in artifically prepared wustites of various compositions have been determined using the decrease in surface activity technique. Similar measurements are reported for artificial magnetites of nearly stoichiometric composition and for natural hematite single crystals. These data, together with appropriate thermodynamic data derived from the present study or from the literature, are used to calculate the rates of oxidation of iron and its oxides, taking as a basis the theoretical rate equations developed by Wagner. The calculations are compared with experimental rate constant data for these same reactions and are shown to provide essential confirmation for the Wagner theory. For the most part, the results are also consistent with the previously proposed transport mechanisms in the oxides of iron. WHEN a metal is exposed to an oxidizing atmosphere at elevated temperatures, a superficial oxide layer is formed which then thickens according to some characteristic rate law. Provided that the oxide layer is dense and continuous and does not present any paths for gaseous diffusion, continued growth must inevitably involve the migration of the reactants—either the metal or oxygen or both—through the lattice of the solid oxide. This is true whether the reaction rate is controlled by the diffusion process itself or by a slow step in a reaction at one of the interfaces. If the overall rate is limited by diffusion, and if the concentrations or thermodynamic activities of the reactants at the boundaries of the oxide layer are independent of time, the familiar parabolic rate law is observed. Under these conditions, Wagner1 has shown that the rate constant may be expressed in terms of the mobilities of the reacting components and the appropriate concentration or activity gradients which are established across the growing oxide layer. In presenting the phenomenological basis for the theory, Wagner has emphasized the role played by lattice defects in diffusion processes in oxides. The essential validity of this theory has been confirmed by experiment for a number of simple systems including the growth of Cu2O on copper.'-' One of the objectives of the present study has been to extend the Wagner approach to the more complex process of the oxidation of iron and its oxides, and particularly to wustite, which is normally the major constituent of the oxide scales formed on iron at temperatures above approximately 570°C. For this purpose the rates of self-diffusion of iron in w?stite, magnetite, and hematite have been measured by tracer techniques and the necessary thermodynamic data have been obtained from equilibrium studies involving the oxides and their atmospheres. These data have subsequently been used to test the underlying assumptions of the Wagner theory as well as the detailed mechanism of the scaling of iron previously proposed by Davies, Simnad, and Birchenall.5 Lengthy treatments of diffusion and conduction phenomena in ionic crystals have been published." * The latest, by Jost,8 also summarizes much of the existing experimental data. In general, however, the oxides of iron have not been considered specifically and hence a brief review of the available

Jan 1, 1954

(Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members.) Members who registered at Institute headquarters during September: William B. Phillips, Austin, Texas. Will L. Clark, Jerome, Ariz. Olof Wenstrom, Boston, Mass. Robert H. Richards, Boston, Mass. Anthony F. Lucas, Washington, D. C. Hennen Jennings, Washington, D. C. P. H. Griffin, New York, N. Y. Waldemar Lindgren, Boston, Mass. H. N. Lawrie, Portland, Ore. C. Snelling Robinson, Youngstown, 0. Clarence P. Linville, Everett, Pa. E. P. Ross, Johnson, Tenn. Members of the XII International Geological Congress who made the Institute Office their headquarters while in New York A. Bigot, Caen, France. E. Gentil, Paris, France. J. Caillebotte, Paris, France. H. Saint-Clivier, Paris, France. John Ashworth, Manchester, England. Tadasu Hiki, Kioto, Japan. T. Dahlblom, Falun, Sweden. L. Milch, Greifswald, Germany.

Jan 10, 1913

By A. P. Miller, T. S. Washburn

Improved procedure in the manufacture of rail steel has come as the rail user demanded better wearing qualities combined with greater unit weight. With each weight increase per lineal yard has come greater difficulty in making a product that would successfully withstand all tests that modern rails must meet. With these facts in mind, and with a sincere desire to produce a rail whose service in track would be satisfactory in all respects, the steelmaker was quick to realize that all of the factors entering into his process would have to be more closely controlled. Control of rail-steel slags was recognized as one of the most important of many interdepending factors. The object of slag control is to hold the slag compositions within a range that gives the best results with respect to economy of production, uniformity of analysis, and quality of the finished rails. The most important component of the slag from the standpoint of these production and quality factors is the ferrous oxide content. This component is a good indicator of the basicity and oxidizing power of the slag, and these largely govern the effect of the slag on the steel. Consequently, the

Jan 1, 1935

By A. P. Miller, T. S. Washburn

Improved procedure in the manufacture of rail steel has come as the rail user demanded better wearing qualities combined with greater unit weight. With each weight increase per lineal yard has come greater difficulty in making a product that would successfully withstand all tests that modern rails must meet. With these facts in mind, and with a sincere desire to produce a rail whose service in track would be satisfactory in all respects, the steelmaker was quick to realize that all of the factors entering into his process would have to be more closely controlled. Control of rail-steel slags was recognized as one of the most important of many interdepending factors. The object of slag control is to hold the slag compositions within a range that gives the best results with respect to economy of production, uniformity of analysis, and quality of the finished rails. The most important component of the slag from the standpoint of these production and quality factors is the ferrous oxide content. This component is a good indicator of the basicity and oxidizing power of the slag, and these largely govern the effect of the slag on the steel. Consequently, the

Jan 1, 1935

By H. L. Riley, B. W. Gandrud

AS far as the present writers know, this system of flotation has not been used elsewhere in this country, but in the last couple of years it has been introduced, with minor variations, at one plant in England and one in Wales.' The system has been described and discussed in a number of publications.2-5 The following is quoted from an abstract of the latest of these,5 a paper presented at an International Conference on Industrial Combustion in 1952. On the basis of experience to date with the commercial plants, it is believed that the kerosene-flotation process incorporates all the necessary elements to make it greatly superior to anything else now available for treating of fines in wet processes of coal preparation. Additional study and investigation are still needed, however, to determine if certain phases of the process can be improved to such an extent as to make it generally satisfactory and acceptable to the industry. Further improvements will be needed with respect to the capacities of the flotation cells and the reagent consumption. The situation referred to above explains why an investigation is being made of the possibilities of achieving better cell capacities. Results obtained from this investigation, which is still in progress, are believed significant with regard to both cell capacity in general and the relation of cell design to cell capacity in particular. Commercial equipment now being used in a laboratory-type investigation should have performance characteristics similar to those of the larger machines. Equipment and Procedures: All flotation tests have been made in a standard Denver sub-A 24x24-in. unit cell of 12-cu ft volume. Cell modifications to make it more suitable for the tests were an adjustable front-wall section for varying cell depth and a perforated scraper-drag assembly for removal of the float product. There is also an apron dry-coal feeder, a gravity-feed water supply, reagent feeders, and a centrifugal pump that feeds the mixture of coal, water, and reagents into the flotation cell. A wattmeter connected into the drive-motor circuit records the power requirements of the impeller throughout each run. Dry coal, water, and reagents are all fed through a pan-type intake to the feed pump. A Sturtevant blower was set up to furnish air for supercharging. A centrifugal pump with a garbage-can intake provides for disposal of refuse flow to an outside settling tank. Figs. 1 and 2 show the flotation cell; Fig. 2 also illustrates the blower for supercharging. For purposes of this investigation, the percentage by weight of the feed coal recovered in the float product under a standard set of conditions has been considered as the criterion of cell capacity. The authors realize that such a criterion may be somewhat unorthodox, as the term cell capacity is usually understood to refer to feed input and ordinarily takes into account the ash analyses of the float product and refuse. However, the word capacity is flexible enough so that Webster gives one definition as maximum output, a definition which seems to justify, at least partly, acceptance of the above criterion. It has been the authors' experience in the Birmingham district that the ash-reduction efficiency of the coal-flotation process is generally satisfactory and that the only real problem is to increase the rate of float recovery so that the feed rate to any given bank of cells can be increased without undue loss of coal in the refuse. Originally it was planned to operate the flotation cell to simulate continuous operation during sampling periods. It was assumed that operating for reasonable time with feed coal, water, and reagents turned on would stabilize conditions so that the weight of float coal discharged during a fixed time interval would be an accurate measure of the rate at which the coal was being floated. It developed, however, that this supposition was erroneous. The float coal, caught for fixed time intervals and weighed, gave widely varying results in duplicate runs. Efforts to correct this trouble failed, and it was decided to try to operate on a batch-test basis, whereby all the float coal produced during a run on a known weight of feed coal would be caught in tubs, dewatered, and weighed. This method gives consistent and reproducible results, with total float product weight rarely varying by more than 3 or 4 pct on duplicate runs. The standard test procedure is as follows: A 132-lb sample of dry feed coal is weighed and placed in the feed hopper. The feeder is adjusted for a rate of 800 lb per hr. Feed water and reagents are turned on, and the feed and refuse pumps are started. One minute later the impeller is started. Six minutes are allowed for the cell to fill up with the water-reagent mixture. The feed of dry coal is started at the end of this 6-min period. One minute later the float-coal removal drag is started. The float coal is caught in one tub for the first 6 min after the flow of feed coal starts. Tubs are then changed, and the float coal is caught in a second tub until the feed coal runs out, when the tubs are again interchanged to catch the float coal for the remainder of the run in the first tub. The cell is kept running for 3 min with the water and reagents on after the feed stops to allow residual float coal to be removed. At the end of a test the wet float coal in both tubs is weighed and the total weight recorded. The product in the second tub is used for moisture determination and screen-size analyses. When the

Jan 1, 1956

By Arthur Phillips, E. N. Skinner

DURING the course of an experimental program concerned with the hydrogen embrittlement of copper containing oxygen in concentrations within the solubility limits it became necessary to make a critical appraisal of the literature dealing with the solubility relationships of oxygen and solid copper. The latest determinations, and perhaps the only data obtained on "spectroscopically" pure copper, are those of Rhines and Mathewson1 who reported that the solid solubility increases from 0.007 per cent oxygen at 600°C. to about 0.015 per cent at 1050°C. Hanson, Marryat and Ford2 had previously placed the solubility limit at less than 0.009 per cent oxygen at 1000°C. and Allen and Street3 had suggested, on the basis of an unpublished research by T. Hewitt, not over 0.005 per cent oxygen at 500°C. In the introductory stages of the investigation indirect evidence accumulated to suggest that the solubility limits were significantly lower than those previously reported. For this reason it was deemed essential to clarify this point before proceeding with a program intended to establish a quantitative relationship between hydrogen embrittlement and oxygen concentrations positively known to be within the solid solution range. Furthermore, the increasing production and the highly selective applications of the commercial "oxygen-free" coppers inevitably direct attention to the practical necessity for exact knowledge regarding the effects of minute concentrations of the elements ordinarily found in the high-purity coppers now available. Of these elements oxygen occupies a unique position, not only by virtue of its specific effects on copper but more particularly in view of its important reactive tendencies toward the other impurities with which it is associated. Rhines and Mathewson considered several methods for measuring the solubility of oxygen and finally adopted the simple plan of saturating the specimens, obtained from redeposited cathode copper, by heating at the desired temperature in air. After the removal of surface oxide by mechanical and chemical means, the oxygen content was determined in the underlying metal. In general, this process of saturation, with a few modifications, was followed by the present writers. Although the procedure is direct and has obvious advantages, its effectiveness, unfortunately, is reduced by an excessive scaling of the copper, particularly at the higher temperatures. After saturation treatments above 900°C. the writers found that the specimens, necessarily rather thin in the original condition, consisted largely of scale and yielded too little metal for a satisfactory analytical sample. Furthermore, great difficulty was experienced in effecting complete removal of the scale. Needless to say, it is necessary to exercise extraordinary care in the preparation of the surface of the analytical sample in order to eliminate submicroscopic fragments of cuprous oxide which ordinarily are lodged in the crevasses and

Jan 1, 1941

THOMAS T. READ, Palmerton, Pa. (communication to the Secretary*). -It is much to he regretted that in presenting a further discussion of these deposits, first described by myself' and later discussed by C. M. Weld,2 Mr. Wang bas not made a more complete presentation of the evidence on which he bases his conclusions as to their origin. Mr. Weld said in his paper that his visit was confined to a few hours, that he saw only one of the several exposures, and that he took away no samples for further study. My own visit was brief, and for another purpose than the study of the geological features of 'the deposits, so the fact that Mr. Weld described as a hornblende-granite the rock which I described as a "dark gray syenitic rock," and which Mr. Wang identifies as a hornblende-syenite, seems of no great importance, since this rock is generally decomposed along the contact, presumably the only place in which Mr. Weld observed it. Later in the same paper (p. 31), Mr. Weld says that his opinion is that the magnetite of the deposits is primary, but Mr. Wang makes no mention of this in stating his own conclusion to the same effect. When Mr. Weld's paper appeared, I did not discuss it, because, although I considered the evidence- that he brought forward to support his belief that the magnetite is primary too slender to support the hypothesis, my own evidence to the contrary was equally tenuous. .The opportunities for observation and study open to Mr. Wang must have provided him with

Jan 6, 1917

By Cornelius F. Kelley

EVERY man connected with the mining industry should take a significant pride in the fact that he belongs to an industry and to a profession that, from the beginning, has been constructive. The miner digs his ore and he gives the metal to art, to industry, and to commerce. The nature of our business is destructive only in that we deal with a wasting asset. That should be a source of great pride to those who belong to the profession. But unfortunately, the product of our mines, our smelters, and our re- fineries does not always go to constructive purposes. There are times when, in the administration of the affairs of men, our product chiefly goes to purposes which are destructive. When we look upon the panorama of horror that is being enacted throughout the world today, we wonder whether any effort toward the development of civilization and culture and education and well-being has been worthwhile. We are appalled to see the things that have been developed, through the application of science, toward progress and efficiency, now used for the catastrophic destruction of those things which are the most valuable that man has built. We must find hope that this is but an episodic thing; that it must, in the infinite wisdom of the Almighty, usher in a period of peace and progress, of civilization and development that will make man's existence upon earth worthwhile.

Jan 1, 1941

Joseph Esrey Johnson, Jr., had already achieved rare distinction as an able metallurgist, clear thinker, brilliant author, and wise consulting engineer to bankers and operators; he had achieved the essentials of a great career when death cut short his activities on Apr. 4, 1919, in the forty-ninth year of his age. He belonged to a family of iron blast-furnace men and mine managers. His father, Major J. E. Johnson, after serving with distinction in the Army of the North, identified himself with the iron mines and blast furnace at Longdale, Va., with which he was connected during almost his entire business life. It is significant that, during those troublous times of reconstruction in the South, he enjoyed always the affection and respect of his neighbors and associates alike. From him his son obtained not only a thorough training in blast-furnace practice and iron mining, but great personal courage and force of character. His mother, who survives both her husband and sons, possesses rare intellectuality, humor and a tenderness and human sympathy which those who were privileged to know well J. E. Johnson, Jr., recognized beneath his exterior of aggressiveness and will power. In a recently published analysis of the qualities which characterize the world's great men, three traits stand out preeminently; viz., independence, courage, and intellectuality. Each of these characteristics J. E. Johnson, Jr., possessed in extraordinary degree. His early education was obtained under a private tutor at Longdale, and this circumstance probably enhanced , a natural tendency to independence of character and individuality which, however, under the control of his

Jan 5, 1919

CANADA, which appears to be growing into one big mining camp, may soon be the background for another impressively large iron ore development. And again it will be Fenimore Iron Mines who will be the motivating force. Dr. J. A. Retty, Fenimore president, who was one of the important figures in the development of Labrador iron deposits, predicts a great future for property on the west coast of Ungava Bay in deep northern area of New Quebec. Fenimore properties consist of a 200 sq mile concession in addition to several hundred claims over about 112 miles along the Labrador trough, mainly in the Ungava Bay region.

Jan 5, 1953

[Officers and Committees of the Society of Petroleum Engineers 1 Officers and Staff of the AIME 2 Officers of AIME Sections Predominantly Petroleum in Membership 3 Society of Petroleum Engineers By-Laws 5 Alphabetical List of Members 9 Geographical List of Members 110 List of Members by Companies 127 Advertisers' Index 137]

Jan 1, 1961

By R. P. Rothwell

THE milling of silver ores has arrived at a great degree of perfection in the mining districts of our Western States and Territories, and I have thought the record of the practical results obtained at the present time, in a few of the principal districts, would prove of value and interest to many of our members, both at home and abroad. An American silver mill is composed, in descending order from where the ore is dumped, of: 1st. A rock-breaker, usually of the Blake or Alden pattern ; 2d. The battery of stamps, the number of which varies from 5 to 120, generally in batteries of 5 or 10 heads, so arranged that a single battery may stand while the others are running; 3d. The tanks where the crushed ore settles (if it is a wet stamping-mill), or of a drying-floor if the crushing is done dry; 4th. Amalgamating pans ; 5th. Settling pans ; 6th. Agitators or pans in which mercury escaping in the tailings is caught; 7th. Blanket sluices, over which the tailings run, and where mercury and unamalgamated sulphides are saved. A reference to the engravings (see plate), which show one of the latest forms of an 80-stamp silver-mill run by a turbine water-wheel, will show clearly the arrangement of the several parts. THE ONTARIO, UTAH, SILVER MILL. One of the best examples of a silver-mill, and at the same time one of the most successful concerns in the West, is the mill of the Ontario Silver Mining Company, near Salt Lake, in Utah. This mill treats the ore from the Ontario mine, ore which at present is very base, being composed of zinc, lead, and silver sulphides and silver chloride in a quartz gangue. This ore has become baser as the mine attained greater depth, though the vein holds its own, or rather increases, both in thickness and richness. The mill is man¬aged in a skilful and economical manner, though the necessity for * Read at the Montreal meeting, September, 1879.

Jan 1, 1880

By O. E. Palasvirta

Close examination of most so-called n.eu processes in mineral dressing reveals that they were conceived and developed a long time ago. High-intensity magnetic separation is no exception. Although its application in iron ore beneficiation seems new, in Germany the process has been commercially successful for almost two decades. High-intensity separators have long been standard equipment in the glass sand industry; they have also been used in concentrating some of the more unusual para-magnetic minerals. The basic features of an induced-rotor, high-intensity magnetic separator were described by Desire Korda in Paris in 1905,' and many patents have since been issued for improvements on the original design. Fig. 1 shows the basic design of an induced-rotor separator. Several U. S. manufacturers have been supplying induced-rotor separators for many years, but these are all devices of relatively low capacity, not suitable for treating such low-cost commodities as iron ore. On the other hand, two German manufacturers are offering induced-rotor separators of high capacity, both proven in the field. The present investigation was prompted by the apparent success of the German installations and by the discovery of iron ores on this continent which may be amenable to high-intensity separation. The objective was to gain better insight into the underlying principles of separation in a high-intensity field and to use this knowledge in selecting or designing an optimum separator. THEORETICAL CONSIDERATIONS he well known low-intensity magnetic separators are. without exception, of the the magnet type with more or less similar field shapes. It is therefore permissible to speak of their comparative strengths in terms of field intensity alone. However, proper understanding of the high-intensity magnetic separation process requires somewhat deeper analysis of the relationship between the magnetic field and the attractive force. Contrary to a widely held belief, a magnetic field of parallel lines of flux exerts no attractive force on a magnetically susceptible particle, but merely aligns its poles parallel to the lines of flux. On the other hand, a non-uniform field attracts a magnetically susceptible particle in the direction of the converging lines of flux. Thus the force of magnetic attraction varies as the product of the field intensity and the field gradient: dH ds As the induced-rotor magnetic separator is primarily intended for separating feebly magnetic materials, it is important that maximum attraction be attained. For the designer, then, the relationship between the magnetic field and the attractive force has the following implications: 1) Insofar as possible, the separation gap must be saturated with flux. 2) The rotor surface must be shaped to insure maximum convergence of lines of flux toward the rotor. 3) The primary pole face (opposite the rotor, on the other side of the separation gap) must be shaped so that the lines of flux do not diverge from it at any location in the effective separation zone. The actual attractive force of the rotor, and its critical speed, can be calculated as shown by Runo-linna, provided that the true flux density, the field gradient, and the magnetic susceptibility of the mineral can be measured with sufficient accuracy. The irregular shape of the rotor surface makes flux measurements difficult, but it can be done if a suitable gaussmeter is available (see Fig. 2). Calculations by the author, and comparisons with the centrifugal force exerted by the rotor, indicate that the force pinning a hematite particle to the rotor is of the same order of magnitude as the force holding a

Jan 1, 1960