Search Documents

By Edward B. Cook

INTRODUCTION. THE installation of the Gayley Dry-Air process appealed specially to the management of the Warwick Iron & Steel Co., for the. reason that for fifteen years records had been kept at the works of the company, showing the amount of water entering the furnace in the form of aqueous vapor, and careful observations had been made of its effect upon the working of the furnace. Some years had proved much worse in their effect than others, on account, not only of excessive moisture, but also of great variation in the moisture from day to day, and sometimes within a few hours. It had been found impossible to. make a satisfactory percentage of high-silicon foundry-iron in summer, even on high fuel; and for some years the endeavor had been made so to arrange the sales that, during July and August, only a small percentage of the iron produced would be required to carry more than 2 per cent. of silicon. Our larger furnace, running on basic iron, year after year, produced in February a tonnage 20 per cent. higher than in August, on a much lower fuel-consumption, while, at the same time, the summer months were marked by ? messes," tuyeres closed by slips, and other irregularities, constituting serious additional business losses. It will be easily understood, therefore, that the records made at the Isabella furnace after the installation of the dry blast in 1904 possessed special interest, and were closely watched by us. On the basis of our own experience, we argued that if the moisture could be kept low, and also uniform, the cost of installation would be more than justified. The subject was brought before our Board of Directors in the fall of 1905; and in the spring of 1906 it was decided to install a plant of sufficient capacity to treat 70,000 cu. ft. of air per min., an amount

Nov 1, 1908

By Victor L. Stevens

The Oso tunnel is one of three tunnels located on the San Juan-Chama Project in south-central Colorado. The purpose of the tunnel is to carry water from the upper San Juan watershed through the Continental Divide into the Rio Grande watershed. The Oso tunnel contract was awarded by the U.S. Bureau of Reclamation to a joint venture of Boyles Brothers Drilling Co., Gibbons & Reed Co., and Cimco in February 1966. The Oso tunnel is 26,660 ft long and has a rock section of 10 ft, 2 in. with a lined diameter of 8 ft circular. The main portion of the rock formation was in the Lewis shale. This formation is quite consistent in hardness and texture with exception of localized limestone concretions and sandy siltstone inclusions. The job was bid on the basis of using a James S. Robbins mole of the P221 series. The decision for using a mole was predicated on the geology and the experience of the same joint venture on the adjoining Azotea tunnel where a mole was successfully used. The Robbins P221 series mole is capable of cutting from 9 ft, 11 in. to a 10 ft, 7 in. diam without any major change. It is 40 ft long and weighs 60 tons. The cutting head has 22 disk-type cutters and one center pilot (standard 9 7/8 -in.) tricone bit. The head is powered by four 75 hp electric motors. Gripper pads at about the midway point on each side of the machine are pushed into the tunnel ribs and thrust-cylinders in front of each gripper apply pressure to the face as the head rotates. The regripping cycle is 3 ft and then the grippers are retracted and advanced. Each cutter on the perimeter of the head is followed by a bucket which scoops up the cut material, almost in the same manner as a water wheel, and dumps it into a conveyor situated along the top of the mole. The muck from the mole conveyor is dumped into a gantry-type conveyor. The gantry conveyor is 350 ft long and is pulled

Jan 1, 1970

By Joachim J. Hauser

William F. Hosford, Jr. (Massachusetts Institute of Technology)—Dr. Hauser has used a very interesting method to study the interaction of dislocations on different slip systems, but it should be pointed out that the analysis of the experiments is subject to a serious criticism. He states that "the effect of the compression can be adequately described by one slip system." The effect of frictional constraint during the compression makes this quite unlikely. When a block of metal is compressed its lateral expansion requires a sliding of the metal over the compression platens. The role of friction in the interface between the deforming metal and the platens is to increase the normal force required for the compression. Analyses1213 have shown that, in general, the additional force, p, required for the compression is a function of l/h where is the coefficient of friction, I is the length of the speci- men in contact with the platens. For a constant COefficient of friction, isho' shows that P should increase exponentially with pl/h for both plane strain and axially symmetric compression. For a compression specimen, Fig. 7, whose cross section perpendicular to the compression axis is a rectangle whith one dimension L, much larger than the other W, a much larger force would be required for appreciable flow parallel to L than for flow parallel to U7. Therefore lateral strain in the W direction, EW, should be much greater than the lateral strain in the L direction EL. Since L/H = 14.5 for Dr. Hauser's crystals, and since no lubrication was used, it seems questionable that appreciable lengthening of the crystals could occur. Because the theories of frictional constraint have been derived for isotropic polycrystalline materials, it was decided to make experimental measurements on a single crystal. A section 3.590 in. long was sawed from an aluminum single crystal with a square section of 0.249 in., so that L/W= 14.4. This crystal was tested in compression between dry ground steel platens. Fig. 8 shows the orientation of the crystal and the axis of compression. The face for compression was chosen so that the operation of the single-slip system which would be predicted in the absence of friction would lead to a larger strain in the length direction than in the width direction. The dimensional changes of the width and length as well as the height were measured frequently during the compression with micrometers. Width strains were calculated from the average of readings near each end and at the center. A plot of the length strain, EL, against the width strain E w is given in Fig. 9. The slope indicates that the EL amounted to only 2.5 pct of cw. Other compression tests on similar crystals with shorter lengths also showed severely limited elongation. Even for a crystal with L/W = A.0, EL was only about 26 pct of cw. Because of the frequent interruptions of the tests for dimensional measurements should have decreased the frictional constraint by allowing a reseating of the platens, even smaller elongations under continuous testing seem probable. These tests on long narrow crystals show that essentially plane strain conditions prevailed. We may assume that Dr. Hauser's crystals deformed similarly. That the compression can be described by the

Jan 1, 1962

By Robert C. Linares

Cubic zinc sulfide has been grown from molten salt solutions substantially below the hexagonal-cubic phase transition of 1020°C. Crystals free of birefringence have been grown from molten lead chloride at temperatures from 500° to 800°C. Factors affecting the optical transmission and the birefringence are discussed. CUBIC zinc sulfide is of interest for electrooptic devices and as an optical coating material. However, it cannot readily be produced as large crystals which are free of birefringence. The birefringence arises from the fact that the cubic ZnS is usually grown as the high-temperature hexagonal phase and is transformed to the lower cubic phase by annealing.' This results in stacking faults, stress, and birefringence. A requirement for the growth of cubic ZnS is that it be grown below the phase transition of 1020°C.2 Crystals of cubic ZnS have been grown below 1020°C by the hydrothermal,3 flux,4 and vapor transport5 techniques. However, these all appear to have limitations in size or quality of material produced. It was felt that a new flux method might have a good chance of overcoming some of the previous problems. Mita6 reported the growth of hexagonal ZnS from molten NaCl and wilke7 reported the growth of iron sulfides from molten lead chloride solution, indicating that molten chlorides make good solvents for sulfides. An investigation of a number of possible molten chlorides as solvents showed that molten PbCl2 has an appreciable solubility for zinc sulfide and that crystals can be grown at temperatures from 500° to 800°C. EXPERIMENTAL Crystal growth was performed in open or sealed Vycor or fused silica tubes, in an argon atmosphere or vacuum. There were no deleterious effects due to using vacuum; however, a sealed essentially isothermal system must be used to prevent vapor transport mechanisms from dominating. This will be discussed later in detail. Noble metal containers were not usable as they were severely attacked by these melts. The materials used were: reagent-grade PbC12, reagent-grade ZnS, optical-coating-grade ZnS, and Irtran 2 (ZnS). Crystal growth was accomplished by both slow cooling techniques and gradient growth techniques. In the slow cooling techniques, 15 g of ZnS and 100 g of PbCl2 were used. The components were placed in the silica tube, heated at 800°C for 2 hr, and then slowly cooled (l° to 10° C per hr) to 500°C. The furnace was constructed so that the tube could be inverted, thus allowing the liquid to drain off the crystals at the end of the run. The gradient runs were made by placing the above mixtures in a silica tube at 550° to 600°c, Fig. 1. A temperature gradient was maintained such that the floating mass of undissolved sulfide was 10° to 50°C warmer than the bottom of the tube. Growth occurred on spontaneously nucleated sites at the cooler bottom. RESULTS When using high cooling rates (5° to 10°C per hr), crystals form in thin sheets perpendicular to the {111} face. Crystals 5 by 5 by 1.2 mm, Fig. 2, have been ob-

Jan 1, 1969

By Roland J. Lapee

A history of the progress made in copper refining in Montana is presented. The casting furnaces and the newly rebuilt electrolytic refinery are descmbed and operating details are given. Experiences with various addition agents, effects of rernoval of chlorine from the electrolyte, and effects of separan on electrolyte and on copper deposit are discussed. Observatzons are made on the effect of various impurities in anode copper and behavior of thezr salts in electrolyte and in slime, on treatment of slime for removal of copper, and on electrolyte puriification problems. The improved method for production of starting sheets is described. Attention is given to new materials for construction and to improvement in matrials handling ad quality control. COPPER refining at Great Falls, Montana, dates back to 1892. The original plant produced 65,000 lb. of cathodes per day at a current density of 16 amp per sq ft. In this plant anodes and cathodes were handled to and from the cells by means of hand-operated chain blocks and were moved about the plant by hand trucks. Cathodes were melted in coal-fired, reverbera-tory furnaces, were charged by hand, and refined copper was dipped by hand and cast in iron molds. In 1916, a new, modern plant with capacity to refine 18 million Ib. copper per month was built. Two refining furnaces were built, and each was provided with a twenty-mold Clark casting wheel. In 1922, the furnaces were converted to the use of pulverized coal: in 1923, to the use of oil; and in 1928, to the use of natural gas. In 1926, the plant was enlarged 50 pct. The use of pulverized coal for refining copper at Great Falls was discussed1 in a paper presented at the Salt Lake City meeting of the Institute in September 1925. Also, a comparison of the use of various fuels in copper refining furnaces was discussed 2 in a paper presented at the New York meeting of the Institute in February 1932. Prior to 1943 the cellroom was operated with twenty-five 720-lb. anodes and 26 cathodes per cell. Four cathodes, each weighing about 165 lb., were produced from an anode. In 1943 the weight of the anode was reduced to 460 lb., and two cathodes, each weighing about 190 lb., were produced from an anode. In 1949, a Billet Casting Wheel for the production of 3 in. diam phosphor deoxidized billets was built. A paper, presented at the New York Meeting of the Institute in February 1956, describes3 this plant and operation. In the electrolytic refinery, production is controlled by variation of the current density. In 1956, germanium rectifiers on a separate electrical circuit were provided for the starting sheet section so that current density could be maintained at any desired figure. Also in 1956, a program of modernization and enlargement of the Electrolytic Copper Refinery was started. This program, when completed, will raise the capacity of the Great Falls Electrolytic Copper Refinery approximately 33 pct, to 33 million lb. of cathodes per month. Furnace capacity for melting cathodes and anode scrap is ample to take care of the increased production from the electrolytic refinery. This fortunate condition came about primarily as the result of the three following changes: 1) The furnaces were lengthened 10 ft in 1922 when the fireboxes were found unnecessary for burning powdered coal. 2) Furnace life, and hence furnace capacity, was increased by the successful efforts of the Copper Refinery staff to develop a method for sanding furnace side walls and roof. 3) The natural gas being used has a very low sulfur content. As a result, it is possible to reduce time spent rabbling and poling and thus greatly increase tons per furnace charge. TANKHOUSE AND TANKS The Great Falls Electrolytic Refinery is 535 ft long by 252 ft wide. The cells are arranged in four crane bays in which are operated seven 10 ton Whiting Cranes. The old cells are in groups of ten, with circulation of electrolyte through five cells in cascade and with aisles between the groups of ten cells. The new cells are nested in groups of sixteen with no aisles, are all on one level, and have individual circulation to each cell. Present plans call for 1792 commercial cells and 128 stripper cells. To reduce confusion during the construction period, and to use the cranes, cars, and other equipment already on hand, the cells in the rebuilt section were designed to have approximately the same inside dimensions as the cells in the old part of the

Jan 1, 1962

MINING ENGINEERING presents the annual membership report of the Society of Mining Engineers; see page 147.

Jan 7, 1964

Between July 10 and August 15, 1918, the Secretary of United Engineering Society, of Engineering Foundation, and of Engineering Council visited 17 cities which are headquarters for large numbers of engineers. His mission was to tell men in all branches of the profession about "Centralized Activities of National Engineering Societies." Stops were made at Denver, Salt Lake City, Reno, San Francisco, Sacramento, Portland, Seattle, Spokane, Anaconda, Butte, Duluth,

Jan 10, 1918

By Roland Kammel

For electrolytic recovery of silver from dilute aqueous solutions improved mass transfer is necessary to achieve favourable current efficiencies and high space-time yields. The many cell designs proposed for this application can be divided into two different groups: cells from which the silver must be redissolved and cells from which the deposit can be reclaimed as a metal. Introduction Electrolytic silver recovery methods have proven advantageous under technical and economic aspects for the treatment of rinse water, still rinses and spent silver solutions in the electroplating and surface finishing industry, of exhausted fixing baths from photographic processing, bleed electrolytes from silver refining processes and leach liquors. Examples of the compositions of typical dilute silver solutions are listed in Table I.

Jan 1, 1984

By C. E. Jackson, E. C. Nelson, A. L. Christenson

Much information regarding the transfornlatio~lal characteristics of a steel as it cools in a known manner from the austenitic state can be obtained from dilatometric studies. This method has received more arid more attention because of its great flexibility, accuracy, and ease of interpretation. 'The method is entirely applicable to any rate of heating and cooling although the experumental procrdures for high rates of cooling have offered some difficulties. This paper presents a description of equipment employing cooling rates up to 500 °C. per secorld and the results of dilatometric observations on six commercial steels are included. French and Klopsch1 studied the cooling transformations of a serirs OF carbon steel, using the thermal arrest method. This was followed by the systematic investigatiol1 of Esser and co-workers on the effect of carhon2 and other alloying additions. in which the transforlnation temperature\ were determined by magnetic induction measurements indicated by a string galranoineter. Emphasis was placed on determining Ar' trailsformations and the critical cooling rates for these steels. The maglietic measurements wrere used in an effort to obtain more accurate data at higher cooling rates. Measurements of thermal arrest were made also to check the validity of the magnetic indications, and good correlation was found between the two, although Esser's,Ar' temperature measurements on iron-carbon alloys were about 200°F. lower than the measurements made by Fresnch and Klopsch. A notable contril~ution by Esser was the introduction gas quenching. wever and Rose4 used a moving-coil galranometcr in the study of the .Ar and Ar" of iron-carbon alloys by the thermal arrest method and obtained somewhat lover Ar" temperatures than those observed by Esser below I per cent carbon and considerably higher ahove. They concluded that the cooling rate had little influcncc on the Ar" temperatures above 0.4 per cent carbon, although Esser had observed a decrease in the -4r" temperature with increasing cooling rate with similar steels. Digges determined the .Ar" temperature4 for a scries of high-purity iron-carbon alloys, and close agreement with his results was obtained by Greninger. The thermal arrest method. together with metallographic observation used in both these studies, represents the latest investigations of this type. Any investigation by thermal analyses is dependent on the heat of reaction and the specific heat of the

Jan 1, 1945

By J. G. Eberhort

ThE literature of surface phenomena shows that, except for most of the rare-earth elements, surface tensions have now been determined for almost every liquid metal. The situation for liquid metal oxides is, in contrast, characterized by a great scarcity of surface-tension data. A surface-tension correlation between these two classes of substances has been found which provides a means of estimating unknown liquid-oxide surface tensions from the corresponding known liquid-metal surface tension. Lf the surface tension of the liquid metal is a(M) and that of the liquid metal oxide is o(M,Oy), then oxides of all stoichiometries can be brought into one correlation if is plotted against with the surface tensions taken at the respective melting points. The available data is displayed in this fashion in Fig. 1 where the relationship between the surface tensions of the two classes of liquids is found to be The correlation in Fig. 1 is based on data found for nine liquid metal oxides and the corre- sponding liquid metals In cases where several sur-face-tension determinations were available on the same substance, higher values were generally favored over lower ones because they usually indicate greater Sample purity. All of the metal-metal oxide pairs are in good agreement with Eq. [I] except for B-Bz03. The reason for the departure of this pair from the correlation is not understood. To estimate the surface tension of other liquid metal oxides the corresponding liquid-metal surface tension must be found. A nearly complete bibliography of the surface tension of liauid elements is available in the 46th edition of the Handbook of Chemistry and physics. Some additional references on metals are included here for convenience Se,26Sr,'?ThanduZ5). It is also possible to estimate the surface tension of a solid metal oxide or metal from the corresponding liquid-state data. As a liquid material is cooled through its melting point the surface tension increases abruptly by an amount Ao. bondi' has estimated that the maximum value of Aa at the melting point is Ao = Ahf/A [2] where Alzf is the heat of fusion per atom and A is the area per atom in the interface. Thus with heat of fusion and crystallographic data the surface tension of a solid at the melting point can be estimated as o + Ao.

Jan 1, 1967

By AIME AIME

THOUGH born in England-on Nov. 23, 1372 William Wraith was brought to this country at the age of ten. Eight years later he entered the University of Illinois, transferring to the Michigan College of Mines where he got his E.M. in 1894. For the next three years he was a mine surveyor for the fuel department of the Santa Fe Railroad. Then he got into the copper-mining industry, which has occupied his attention for the last forty years. First he was engineer, at Butte, for the Boston & Montana company, and then helped to build the Washoe smelter at Anaconda, of which he was assistant superintendent from 1906 to 1913. The Anaconda company then sent him to Salt Lake City as manager of its subsidiary.

Jan 1, 1938

THE CHAIRMAN (G. H. CLEVENGER, Stanford University, Cal.).¬I would like to ask Mr. Pyne if he has had any experience inn the use of chromite as refractory under conditions that are highly reducing? I am reminded of an experience I once had with an electric furnace. I imagined that chromite would form a splendid lining, but it soon disappeared; hence it seems probable that, under highly reducing conditions at a high temperature, chromite is a very poor refractory. F. R. PYNE.-In copper smelting the atmosphere is generally neutral, or slightly oxidizing; we do not use highly reducing atmospheres at all, not even in the matting furnace. You can take the chromite brick and treat it as you would an iron ore, obtaining ferro-chrome very readily, from which the copper will separate. We have done this; in fact, at one time we considered installing a small electric furnace for the production of ferro-chrome. FOREST RUTHERFORD, New York, N. Y.-During the time I was general superintendent at the smelter of the Copper Queen Consolidated Mining Co., at Douglas, Ariz., a great many experiments were made on the furnaces and settlers with different kinds of brick, and I agree with Mr. Pyne's statements about chrome brick. Their power to absorb metals is very great, and as they cannot be smelted at any temperatures obtainable in a copper furnace, to get rid of the bats and extract the metal from them is quite a problem. We finally got down to using chrome brick only for lining the settlers, out of which we often got a life of upwards of 2 years, and for lining the blast-furnace bottoms, for the reason that chrome brick can be heated and wet, or wet after being heated, without going to pieces, whereas under these conditions magnesite brick will break down very rapidly. We also used a layer of chrome brick above and below an 18-in. band of magnesite brick put on the slag line of the reverberatories, in order to separate the magnesite from the silica brick, fearing that they would slag each other and let the wall drop. The idea worked, but became unnecessary on account of a change made in the method of feeding the furnaces. Chronic brick will not stand up under pressure so well as a good Grecian or Austrian magnesite brick, on account of the poorer bonding properties of the materials from which the chrome brick is made.

Jan 4, 1918

CONTENTS PAGE ANDERSON, ROBERT J., and ENOS, GEORGE M.-Corrosion of Brass as Affected by Grain Size. Discussed by Henry S. Rawdon, Robert J. Anderson, Francis B. Coyle, William B. Price, and W. R. Webster 1 RAWDON, HENRYS., and MUTCHLER, WILLARD H.-Effect of Severe Cold Working on Scratch and Brinell Hardness. Discussed by W. H. Bassett, John Livermore Christie, John R. Freeman, Jr., W. R. Webster, William B. Price, Norman B. Pilling, D. J. McAdam, Jr., F. G. Smith, Zay Jeffries, F. E. Carter 3 WILLIAMS, ROBERT S., and HOMERBERG, VICTOR 0.-Relation of Heat Treatment to the Microstructure of 60-40 Brass. Discussed by 0. W. Ellis 14 Corrosion of Brass as Affected by Grain Size Discussion of the paper of ROBERT J. ANDERSON and GEORGE M. ENOS, presented at the New York Meeting, February, 1924, and issued as Paper No. 1282, with MINING AND METALLURGY, December, 1923. HENRY S. RAWDON,* Washington, D. C. (written discussion).-So numerous and so varied are the factors that affect the corrosion of metals that particular care is necessary in corrosion tests to eliminate so far as possible all extraneous factors. It appears to the writer that the question may well be asked as to whether all the necessary precautions have been observed in this investigation. It may be that the points to be mentioned were considered by the authors and found to be insignificant; however, there is nothing in the report to show this.

Jan 5, 1924

By Frederick A. Mumpton

For more than 200 years zeolites have been familiar minerals to geologists and mining engineers as minor, but ubiquitous constituents in vugs and fractures of most basalt and traprock formations. More than 35 different species have been recognized including several, such as chabazite, erionite, mordenite, and faujasite, whose adsorption properties rival those of many synthetic molecular sieves. Igneous occurrences of this type have never been mined on a commercial scale; they are generally small and low grade, and they commonly contain as many as four zeolite minerals, along with small quantities of calcite, quartz, and other silicate minerals. Their economic beneficiation to monomineralic zeolite products has also not been achieved and, for the most part, industrial applications of zeolites have relied primarily on synthetic molecular sieves that were crystallized from hydrous aluminosilicate gels. During the middle 1950s, when Union Carbide Corp. and other groups were developing processes and markets for their fledgling synthetic zeolite businesses, natural zeolites

Jan 1, 1975

By Roberto Fernandez

Want of knowledge on the part of experts from abroad respecting the amalgamation-system, known as the Mexican or patio process, has been the cause in this country of trouble to many foreign mining companies. This process has not been looked upon by their managers as a satisfactory method of treating silver-ores, and they prefer to employ others, which, although more modern, and often more profitable in other countries, have not proved to be so under the exceptional conditions of this country, where labor is cheap and paid in silver, while fuel is very dear. The cause of this error of judgment is probably the inexact information which has been furnished by several authors respecting the economical results of the patio process. This treatment is not suitable for silver-ores of every kind. Simple sulphides of silver are best adapted to it, and, next to these, the combinations of complex sulphides, viz., pyrargyrite, polybasite, stephanite, proustite, etc. Chlorides, bromides and iodides of silver are considered rebellious ; argentiferous galena, blende, bournonite, as also argentiferous arsenical pyrites of iron and copper, are absolutelg unsuited to this treatment. Experience has proved that high-grade ores do not give as satisfactory results as those of mediurn grades, as, for instance, carrying from 1 to 2 kilos of silver per metrical ton. The patio process, as actually practiced in this district, comprises the following operations: 1. The ore is crushed in a dry state in a roller-mill, reducing it to pea-size, from which uniform samples, and, in consequence, correct assays, can be obtained. 2. It is then thrown into the arrastra, and pulverized with water, so fine that it will pass through an 80-mesh screen.

Jan 1, 1900

By Brian Mason

Wire Ropes in Mines. Proceedings of a conference held at Ashorne Hill, Leamington Spa, Warwickshire, September, 1950. Published by the Institution of Mining and Metallurgy, Salisbury House, London, 1951. 828 P. $7.00-The volume contains 18 pages on the manufacture and properties of rope wire and wire ropes. In addition, wire rope practice in Britain, Ontario, the Witwatersrand, The United States, South Africa, and other countries are discussed. Testing, government regulations, and inspection are also treated. The book contains a three day discussion on these subjects complete with a summary of conclusions and recommendations. Heating Ventilating Air Conditioning Guide 1952. Published by the American Society of Heating and Ventilating Engineers, New York, 1952. 1496 P. $7.50.Contains a technical data section of reference material on the design and specification of heating, ventilating and air conditioning systems. Also has a section containing information on equipment and manufacturers. An index to technical and equipment sections is included.

Jan 1, 1952

THOSE NOT MARKED ARE MEMBERS; MARKED THUS ?ARE ASSOCIATES. HEAVY-FACED TYPE SIGNIFIES HONORARY MEMBERSHIP JUNIOR MEMBERS ARE MARKED ' . THE FIGURES AT THE END OF THE ADDRESS INDICATE THE YEAR OF ELECTION. AARONS, J. BOYD See Honor Roll. '05 ? AARONSON, ALFRED E Pres., Tuloma Oil Co., Unity Bldg., Tulsa, Okla. '18 ABADIE, EMILE R., Min. En r Box 291, Porterville, Tulare Co., Cal. '76 ABBOTT, CLARENCE E., Gen'l Supt., Iron Mines Div., Tenn. Coal, Iron & R. R. Co., 1405 Minnesota Ave., Bessemer, Ala. '04 ABBOTT, Louis BENJAMIN, Chief Engr., Consolidation Coal Co., Elkhorn Div., Jenkins, Ky. '15 ABBOTT, ROBERT R Met. Engr., Peerless Motor Car Co., Cleveland, Ohio. '12 ABE, ASAKA Fujitagumi Taiwan Office, Taipeh, Formosa, Japan. '14 ABBY, HIROSHI Min. & Met. Engr., Mitsubishi Co., Tokyo, Japan. '17 ||ABOUCHAR, S. S., Cia. de Minerales y Metales, S. A., Minas Viejas, Villaldama, N. L., Mexico. '17 ABRAHAMS, A. I 1391 Madison Ave., New York, N. Y. '14 ?ACKER, E. O'C., Met.,128 East Washington Lane, Germantown, Philadelphia, Pa. '86 ? ACKERMAN, ERNEST R., Pres., Lawrence Portland Cement Co., Plainfield, Union Co., N. J. '15 ACOSTA, J. N., Min. Engr., Cons. Engr Hotel Brewster, San Diego, Cal. '15 ADACHI, JINZOO 11 Shiba Park, Shiba-Ku, Tokyo, Japan. '88 ADAMI, CHARLES J., Min. Engr., Gen'l Supt., St. Joseph and Doe Run Lead Companies, Bonne Terre, Mo. '12 ADAMS, ARTHUR K., Min. Geol., Andes Copper Min. Co., Casilla 230, Antofagasta, Chile. '06

Jan 1, 1923

By S. Chander, D. W. Fuerstenau

The inherently sluggish nature of the reactions involving sulfide minerals, particularly molybdenite, in aqueous solutions under ambient flotation conditions make their investigation complicated and difficult. Since the physicochemical nature of sulfides is known to be controlled by electrochemical reactions, a number of attempts have been made in the past to study sulfide mineral-collector interactions through rest potential and electrode polarization measurements. The purpose of the present investigation was to study the interaction of potassium diethyldithiophosphate (KDTP) with molybdenite. In the present investigation of the interaction of KDTP at the molydenite surface, molybdenite electrode rest potential measurements and electrode polarization behavior were experimentally determined under various solution conditions. The standard reduction potential for the equilibrium between dithiophosphate ions (DTP-) and bis(diethoxythiophosphoryl)disulfide (DTP) [(DTP). + 2e :i7-± 2DTP- (1)] can be evaluated from the electrode rest potential measurements on a platinum electrode in deoxygenated KDTP solutions saturated with freshly prepared (DTP)2. Experimental A platinum wire was used as the electrode for potential measurements. Prior to each measurement the elec-

Jan 1, 1975

By M. Tanaka, S. Kita, Y. Jinnouchi, Y. Sawada

This paper generalizes the results of the recent theoretical and experimental investigations on the air-pulsated jigs in Japan. The pulsating mechanism is analyzed as a special vibratory system, and the jigging mechanism as a mass system subjected to the law of hindered settling. The results of investigations on the following items are reviewed: dynamics of the pulsating mechanism; pulsation in a practical TACUB jig development of a new type of air valve; uniform pulsation in a large Baum jig; motion and mobility of bed particles; separating speed in hindered conditions; and standard deviation in practical jigs.

Jan 1, 1985

By Richard L. Stowe, Donnie L. Ainsworth

The static, rapid, and shock-loading response of rock is of interest to many in the field of rock mechanics. For example, the effects of loading rates on strength and stress-strain characteristics of rock are quite important in defining input loading for use in the design of underground protective installations. Response data on rock subjected to shock loading over a wide range of pressures are also vital in the field of underground nuclear testing. In addition, material response is needed in design of shock-absorbing liners. A number of investigators have reported that ultimate compressive strength of rock increases with increased rates of loading.1-6 Wuerker3 stated that modulus of elasticity, obtained from sonic determinations, increased in some rocks by a factor as high as 4.5. It appears that only a limited amount of work has been done on comparing static modulus and modulus obtained from impact testing.6 Phillips4 showed that with increased rates of loading the deformation decreased. More recent work by Atchley and Furr5 showed that when moderate-strength concrete is stressed with increased loading rates, the axial strain at failure increased. One would expect this to occur if we think in terms of purely elastic materials. For example, if E is constant and maximum strength [amax], increases, the axial strain would also increase. However, in rock testing thus far we have worked almost exclusively with nonhomogeneous and inelastic rocks. From this fact alone the increase in axial strain with increased load application is noteworthy.

Jan 1, 1972