Search Documents

The sphere of operations of dry crushing has been so much enlarged of late years that the following notes with reference to its advantages and limitations, and also some practical results in connection with the crushing of gold ores will probably be of service to the members of the Institute. Until recently, with one notable exception that of the Mt. Morgan Gold Mine, dry crushing has only been practiced to a very limited extent in Australasia, and elsewhere it might be said to belong to industries other than mining Its sphere of usefulness depends on the fact that the' product is delivered in a dry state without the separation of the finer particles from the coarser to any appreciable extent, thus enabling the following advantages to be achieved with different ores.

By J. -Y. Jia, G. -B. Qiu, C. -G. Bai, D. -F. Chen

Due to the great importance of the smelting process, it is essential to establish a calculation model on the viscosity of the slag system containing titania. In this paper, the calculation models of mass action concentrations and viscosity for the CaO-SiO2-TiO2slag system have been established according to the coexistence theory of the slag structure, as well as the referenced viscosities ofCaO-SiO2-TiO2at different temperatures and TiO2compositions. With the two models, corresponding calculated programs are made by means of programming language Matlab5.3, and the curves of viscosity of the TiO2concentration (?TiO2/%) at 1400°C, (R=0.9~1.0) are plotted. The results show that mass action concentrations of TiO2increases with increasing percentage ofTiO2, while the viscosity of CaO-SiO2-TiO2system is decreased. The results show that the models are in good agreement with the experimental and referenced data. They also shows that the models are reasonable for the CaO-SiO2-TiO2slag system. Keywords: coexistence theory; CaO-SiO2-TiO2slag system; viscosity ; calculation models.

Jan 1, 2004

Resources and reserves are critical inputs into the determination of an operating mineÆs financial results and balance sheets, but how well understood is this fact. Do the investors, directors, accountants and geologists/engineers responsible for preparing or relying on relevant aspects of the end results properly understand the inputs and outputs and the associated risks that may be established. The first step is to understand how financial reports are impacted. The most obvious, and best known, impact is in the calculation of depreciation and amortisation charges against long term assets. In addition, however, there is a requirement to regularly determine whether asset book values are impaired û this is nearly always performed globally by the preparation of a discounted cashflow model for a mine which is usually based on a mine life as determined from the resource and reserve statement û the particular driver here is normally the short and long term production plans. A key aspect of the short term production plan is that it would normally not assume that the reserve and resource statement implies consistent grade, stripping ratios, etc. However, outside of the early years of a plan, more generic assumptions of these variables are often made in conjunction with the reserve and resource statement. Depending on the timeframe of the detailed production plans, this can have a large impact on a projectÆs net present value. Other financial balances that may also be impacted include restoration and rehabilitation provisions, retrenchment provisions and deferred or equalisation stripping accounts. The age old question of whether all reserves should be used or whether some or all of the resources should be included for financial reporting purposes has never been adequately resolved. It is our view that there should be no prescriptive answer to this question but judgement of all professionals involved in the process needs to be included. Furthermore, the company needs to be able to support their conclusions with well thought out and appropriate answers. This may not be in line with the approach that certain accounting standard setters may be proposing or taking, and this paper will outline the current status of global requirement and the likely future directions. Whether reserves or resources are utilised, does not change the key requirement that those preparing or using reserve and resource statements need to understand key aspects. For example: geologists/engineers do they know how reserves or resources will be used? have they imparted information on variability of key drivers such as grade or depth or dilution? do they know that major financial/business altering decisions may be made based on the analysis? accountants do they understand where the numbers have been derived from and the assumptions that may have been made in their determination? do they understand the degree of accuracy (or inaccuracy) that may exist particularly with resources)? do they understand the history of resource reconciliations and what it may mean for the future? directors do they understand the processes undertaken by the company to prepare the financial report and the interaction between the geologists/engineers and accountants? do they understand the potential sensitivity of results to the input variables? Financial reporting is extremely reliant on the use of the reserves and resources, however, the geologists/engineers, accountants and directors do not always understand the interactions between themselves which may lead to misleading public reporting. More education and communication between various parties is needed.

Jan 1, 2002

By Jerry Gagnon, Matt Burr, Dave Evans, Timothy Ellis, Davies Kakengela, Abbas Mirza, Larry Webb, François Leclercq, Andrew Johnston

Lead-based alloys are the primary anodes used in electrowinning from sulphate-based aqueous systems. Lead anode technology has evolved over the years, migrating from pure lead and lead-antimonial alloys to the present day lead-calcium-tin alloys for copper electrowinning and lead-silver alloys for zinc electrowinning. It has also migrated from cast to rolled microstructures in search of improved mechanical properties and higher corrosion resistance. Although great strides have been made in the development of new alloys and production processes, the industry still has unresolved issues related to untimely corrosion which limits anode life and may lead to higher contaminant levels in the metal being produced. Lead anodes corrode because of the difference in the chemical/electrochemical potential across the microstructural features of an anode. Given a very high purity material, we find that the grain boundary areas corrode significantly faster than the rest of the grain. The desire to minimize grain boundary corrosion by a balance of alloying element selection and microstructural design allows the grain boundary area to be engineered. However, operational issues can lead to unexpected corrosion behaviours which we will discuss moving forward. The comments in this work, though directed toward copper electrowinning, can be extended to similar phenomena in other metals electrowon from sulphate media (i.e., zinc, nickel, cobalt, manganese). The lifecycle of electrowinning anodes is dependent upon electrowinning tankhouse operating conditions and maintenance of the anodes, including cleaning and straightening. This paper will focus on the operational aspects of maximizing the utilization of lead electrowinning anodes.

Jan 1, 2015

By Forrest T. Moyer

THIS CHAPTER of the Minerals Yearbook contains injury experience and related employment information for the coal-mining, coking, oil and gas, peat, and native asphalt industries in the United States for 1963. No attempt has been made to combine these data and present injury-frequency rates reflecting the mineral-fuel industries because the hazards of the separate industries are not comparable. Tabulations showing the trend of injuries and employment for all mineral industries are presented in Volume III of the Minerals Yearbook. COAL Injury experience of the coal-mining industry was improved slightly in 1963, as measured by the 2-percent decline in the Injury-frequency rate. Although the total number of fatal and nonfatal injuries increased 1 percent, the greater proportional increase of 3 percent in man-hours worked accounted for the improved frequency rate. Employment and injury data for 1963 are based on final data for anthracite mines and preliminary data for bituminous coal and lignite mines.

Jan 1, 1964

By A. Iannacchione

Longwall mining began within the Pittsburgh coalbed of Pennsylvania (PA) in the early 1970?s. Originally, longwall mine layouts were designed to fit within existing room-and-pillar operations, where panels were limited to that of typical production panels, e.g. a few hundred feet wide by a few thousand feet long. In these early designs, the gate entries were comprised of chain pillars similar to those found along main entry systems or within pillar recovery sections. The modern longwall mine has little in common with their 1970?s predecessors. Today the entire mine layout is designed around the longwall mining method. The longwall panels have grown to well over one thousand feet in width with lengths now measured in miles. In addition, development pillar sizes and shapes are matched to specific performance requirements.

Feb 27, 2013

By Ludovic Charpentier

Production of metallic wires directly from liquid jets would avoid drawbacks of extrusion (space needed, damaging, cost?) and enable recycling. But liquid jets tend to break, due to capillary instabilities, unless a solid layer (coating or start of solidification) surrounds it. We recently developed a process to produce tin wires, cooled by water flow parallel to the jet. Superficial oxidization of tin produces a glass coating around the jet. Studies showed the length of wires increased when increasing speed of tin jets, and that water average speed should be the closest possible to the jet one to have smooth fibers. Producing 1 mm diameter wires is possible. The length of wires is limited by the experimental setup, which does not provide possibilities to coil the wire. Most of other metals do not generate glass-like oxides. The lack of coatings makes it necessary to reduce the capillary instabilities to obtain fibers.

Jan 1, 2006

By Richard Mainiero, Donald A. Hurd, James H. Rowland

In previous conferences the authors have reported on toxic fumes generated by the detonation of ANFO. The research reported here extends the earlier work to include an emulsion blasting agent and ANFO/emulsion blends. Explosive mixtures were shot in 4-inch Schedule 80 steel pipe in a chamber in the experimental mine at the Pittsburgh Research Laboratory (PRL). Following each shot, the fumes in the chamber were analyzed using on-line instrumentation. A major goal of the research was to gain a better understanding of the factors that lead to the generation of toxic fumes in blasting operations. Earlier studies have suggested that the high nitrogen dioxide and nitric oxide concentrations in product clouds might be the result of the poor confinement provided by relatively weak ground strata or the exposure of the explosive to ground water prior to shooting the shot. Various mixtures of ANFO and emulsion were detonated in schedule 80 steel pipe and galvanized sheet metal pipe to evaluate the effect of confinement. Explosive mixtures were also allowed to soak in water for less than one day, one week, one month, and two months to determine which explosive mixtures would be degraded and observe what effect this degradation had on fume production. Results indicated that the production of nitrogen dioxide increased with low confinement of the detonating explosive and with exposure of the explosive to water.

By J. Kerr

The first stage of the development of a new modified 201-type low nickel austenitic stainless steel is described in this paper. The alloy is intended for use as a structural alloy, and so requires a yield strength >400MPa as well as acceptable weldability and toughness. The low nickel content will give a lower material cost in comparison to more conventional austenitic grades, and the processing route is required to be similar to that of Type 304 to keep the processing cost low. The base alloy was designed using empirical methods developed for stainless steel, and the properties of the base alloy were verified using a range of small-scale melts. The base alloy had a 0.2% proof strength of ~320-400MPa, and so it is planned to use V additions of ~0.15% to bring about precipitation strengthening in the hot rolled condition, so raising the alloy?s proof strength above the 400MPa minimum.

Jan 1, 2004

By Forrest T. Moyer

The overall injury experience, excluding officeworkers, at metal mines and mills during the period 1961-63, reported by operators, was 174 fatal and 11,357 nonfatal disabling work injuries during an aggregate worktime of 451 million man-hours. These injuries occurred at a frequency rate of 25.55 per million man-hours, comprising 0.39 for the fatal and 25.17 for the nonfatal injuries. The combined severity rate of the disabilities was 3,779 days lost or charged per million man- hours, consisting of 2,314 for the fatal and 1,465 for the nonfatal injuries. The average severity of all disabilities during 1961-63, was 148 days per injury. The number of days lost and/or charged, ex- cluding officeworkers, at metal mines and mills during the period 1961-63, was 1,440,000 days charged to fatal injuries and 661,290 days lost from nonfatal injuries. An average of 70,966 men were at work daily. The outstanding cause for fatal injuries was the fall of rock or ore from the back, while most of the nonfatal injuries were caused by handling materials, slips or falls of persons, machinery, falls of rock or ore from back and side, and haulage. Injury experience at primary nonferrous smelters, refineries, and reduction plants during 1961-63, excluding officeworkers, was 23 fatal and 3,214 nonfatal disabling injuries during a total work- time of 277 million man-hours. The injuries occurred at frequency rates of 0.08 per million man-hours for the fatalities and 11.61 for the nonfatal disabilities. The severity rate for all injuries of 1,085 days lost or charged per million man-hours comprised 498 for fatal and 587 for nonfatal injuries. The number of days lost, excluding officeworkers, at primary nonferrous smelters, refineries, and reduction plants during 1961-63 was 138,000 from fatal injuries and 162,385 from nonfatal injuries, An average of 34,938 men were at work daily an active plant days during the three year period. The injury experience for officeworkers at metal mines and mills during the period 1961-63 was 20 nonfatal disabling work injuries, (there were no fatal injuries reported), during an aggregate work-time of 28,694,244 man-hours. These injuries occurred at a frequency rate of 0.70 per million man-hours. There were no fatal injuries reported for officeworkers at non-ferrous smelters, refineries, and reduction plants during 1961-63, but seven nonfatal injuries were reported during an aggregate work-time of 30,814,772 man-hours. The frequency rate for these injuries was 0.23 per million man-hours for this period.

Jan 1, 1967

By Gregory M. Molinda

Extremely difficult ground conditions were encountered in the main belt entry in a room and pillar mine in West Virginia. Several generations of supplemental support, including cable bolts, cribbing, and Heintzmann jacks and beams failed to halt roof falls that threatened workers safety and the life of the mine. Polyurethane (PUR) was injected into 27 intersections in the roof and the results were monitored by borehole video camera. The mine had averaged 2-3 falls in the beltway per year and, since the roof injection, no roof falls have occurred. Pre- and post injection monitoring of test holes showed that stability can be achieved without filling all of the existing void spaces. Video logging showed that the project goal of building a beam from 2-6 ft into the roof was successful. Pre-injection monitoring of roof fractures uphole can delineate the zones to target for reinforcement, and avoid pumping PUR into large voids to little effect. Multiple-injection zones can be identified, and the entire intersection drill hole array can be optimized based on knowledge of the fractured zones. In addition, pre-monitoring can prevent excessive hydrofracturing in solid zones. Polyurethane injection is a proven method of rock stabilization in even the weakest, most broken ground. Optimization of the injection design by pre-injection video diagnostics can greatly contribute to the successful and efficient roof stabilization.

By V. Riihimäki, M. Luotamo

The Unit of Toxicological Risk Assessment of the Finnish Institute of Occupational Health (FIOH) is conducting a 'Health Risk Assessment for Metallic Chromium and Trivalent Chromium' under the sponsorship of the International Chromium Development Association (ICDA) and the International Stainless Steel Forum (ISSF). This risk assessment will be conducted in accordance with the current European Union legislation in force (Council Regulation 793/93/EEC, Commission Regulation 1488/94/EEC, Dir. 67/548/EEC), but also to meet the regulatory obligations as set out in the European Commission REACH legislation proposal (Consultation Document, the Registration, Evaluation, Authorisation and Restrictions of CHemicals). Further aims include outlining the criteria for the setting of occupational exposure limits for metallic chromium and trivalent chromium compounds. Human Health Risk Assessment according to the current legislation shall entail hazard identification of the toxic end points (acute toxicity, irritation/corrosivity, sensitisation, repeated dose toxicity, mutagenicity, carcinogenicity, reproductive toxicity) including, as appropriate, dose (concentration) - response assessment, and derivation of the N(L)OAELs (No (Lowest) Observed Adverse Effect Level) and/or DNELs (Derived No Effect Level). Exposure assessments for workers, consumers and humans exposed via the environment take into account all the known intended uses. Risk characterisation will compare the typical and/or reasonable worst case exposure estimates to the N(L)OAELs or DNELs to determine Margins of Safety (MOS) for all human populations by each exposure scenario and type of effect, followed by conclusions about the presence or absence of risk. Although all of the key elements of existing legislation remain in REACH, the principal change is that, the burden of proof will be transferred from the member state authorities to industry. The new proposed format of Chemical Safety Report (CSR) will include Risk Management Measures (RMM) as an essential part of the report in addition to the risk assessment. The RMM plays a role in the evaluation of further testing needs and advocating reasons for possible waiwer of requirements. The research programme started in March 2002 and will be completed within the time frame of two years.

Jan 1, 2004

By K. Collett

Elandsrand started shotcreting back in 1991. This paper will share the experiences of the mine by looking into the past, the present situation and the way Elandsrand plans to approach the future. It looks at the application of drycrete and discusses the factors that led to the introduction of wet fibre reinforced shotcrete. The logistical constraints of getting shotcrete material underground will be solved by the development of an underground batch plant, using run of mine waste rock as an aggregate.

Jan 1, 1998

By M. Grodner

Underground excavations exhibit different hangingwall conditions in response to varying geotechnical and mining situations. These differences need to be quantified so as to accurately determine the effectiveness of the mining and/or support strategies. A useful tool for the quantification of these differences is hangingwall profiling. Two methods of hangingwall profile measurement are described?termed irregular and periodic methods. Several data analysis techniques are reviewed for these methods and the suitable ones are discussed in detail. For irregular data the suitable techniques are the determination of the length, the average of the profile and the average absolute deviation from the mean of the profile. All of these techniques as well as determination of the moving average of the height and examination of the spectral image of the profile can be successfully applied to regular data. The effect of preconditioning on the hangingwall is discussed as an example and it is quantitatively shown that it results in improvements of conditions. The techniques described allow the engineer to quantitatively identify the appropriate support type or mining strategy and thus represent a valuable decision-making tool. It is suggested that these techniques should be employed on a routine basis by the rock engineers on the mines as part of their geotechnical classification, as well as support manufacturers to quantify the effectiveness of various support types.

Jan 1, 2000

The Bureau has published much data on sulfur (4, 15, 23)3, most of it dealing with national or international aspects of the sulfur industry. Little information, however, is available on sulfur marketing in specific States or areas, Therefore, the Bureau has conducted a survey of the resources, production, consumption, and economic future of the sulfur and sulfuric acid industry in States of the Central and Southern Rocky Mountain area - Wyoming, Colorado, Utah, Arizona, and New Mexico - and in the Northern Plains States - North Dakota, South Dakota, and Nebraska, even though these States do not represent an economic or marketing unit. The purpose of this survey is to review the demand for sulfur and primary sulfur compounds that draws upon the natural resources of the region, to discover opportunities for better use of these resources, and also to analyze and evaluate the patterns of consumption, sources of supply, and other factors that affect the demand for these mineral products. While this survey stresses the economic and marketing phases of the industry, a complementary report (32) emphasizes the resources of sulfur in Wyoming, Colorado, Utah, New Mexico, and Arizona.

Jan 1, 1962

By X. Q. Cao, D. S. Zhang, L. Q. Ma

To solve the support stability control problem for a coal face with large angles along both strike and dip (CLSD), the ’support-surrounding rock’ mechanical model has been developed, which takes into account the impact of the dip angle of the seam on the stability of the support in the strike direction. The mechanical relationships of the critical topple angle and critical slip angle of the support along the strike of the coal face with large dip angle and the support height, support resistance, friction coefficient, and other factors have been derived through the mechanical analysis of support stability in the strike direction of CLSDs in the free state, the operating state, and the special state. The research findings were applied to a fully mechanized CLSD in Xinji Coal Mine. The maximum underhand angle and overhand angle in strike are 42° and 25° respectively, and the maximum dip is 39°. It is calculated that during underhand mining and overhand mining, the critical support resistances for avoiding support toppling are 3723 kN and 1714 kN respectively, and the critical support resistances for avoiding slipping of the support are 7405 kN and 6606 kN respectively. Thus, the selection of type ZZ7600/18/38 hydraulic roof support for the coal face is justified. Measures to prevent sliding of the support and the installation of a limiting stop maintain the support runs in good condition and ensure safe and efficient mining of CLSD.

Jan 1, 2015

By E. L. Garton

Michigan is becomining one off the important oil-producing States of the country, The amount of crude oil produced within its boundaries has increased from only 4,000 barrels in 19253/ to nearly 16 million barrels in 1935.4/ The Bureau of Mines method of crude-oil analysis and classification indicates that the oils from the several producing fields are predominantly paraffin-intermediate-base, wax-bearing crudes. In general, they will yield 25 to 35 percent of highly paraffinic gasoline and about the tame amount of kerosene and gas-oil combined, 12 to 15 percent of lubricating oil stock, and 20 percent of residuum with a carbon residue of about 6 to 7 percent. In addition, there appears to be some correlation between certain properties of the crude oils and both the geographical location and geological structure of the oil-producing areas within the State. These general conclusions are based on the analytical data presented in this report, which is one of a series of papers that record the general characteristics of crude oil from the many producing fields of the United States. This report discusses briefly the oil fields of Michigan and the characteristics of the crude oils produced from them. The analyses of 15 samples are given. These samples were obtained from 13 fields in S counties in the lower peninsula and represent crude oils produced from the Berea sandstone, Upper Traverse and Traverse limestones, and the

Jan 1, 1937

By Miklos D. G. Salamon

If all stratifications are horizontal, the computation of surface deformation induced by coal mining involves the prediction of roof and floor convergence and then the transfer of the effects of this relative displacement to the surface through the use of the appropriate influence functions. A laminated model, in the form of a quasi- continuum, provides a simple means of computing the approximate convergence distribution and leads to the Gaussian distribution as the influence function. The ideas presented in this paper represent a subtle but fundamental generalization of the influence function Method. It is postulated that the influence of a small area of extraction is proportional to the roof and floor convergence and not to the thickness extracted. This difference in definition removes many conceptual difficulties associated with the influence function method. To demonstrate the utility of the model, the surface disturbances induced by the extraction of a parallel sided long panel are derived. Formulae giving subsidence, tilt, horizontal displacement and strain are given.

Jan 1, 1989

By Bruce Watzman

"Few issues are more important to the National Mining Association (NMA), the U.S. mining industry and NMA’s MINExpo International 2016 exhibitors than safety.Global mining safety and health is a journey necessitating continuous improvement, collaboration and innovation on the part of both mining operators and their suppliers.MINExpo 2016, which takes place Sept. 26- 28, 2016, in Las Vegas, provides attendees with the opportunity to view technologies to help refine management of mining safety and health, utilizing NMA’s CORESafety system. CORESafety ‘One of the best’Launched by NMA in 2011 and moving forward ever since, CORESafety is driving continuous improvement in safety and health performance among participating industry companies by shifting from a command-andcontrol regulatory approach to a risk-based systems approach built on the Plan-Do-Check-Act model (Fig. 1).Considered an exemplary safety and health management system, NMA’s CORESafety system helps mining operators change their approach to safety and health management by enhancing the safety and health culture throughout their organizations. Although it is challenging to consistently and completely control all the factors and variables occurring in daily mining operations, experience has shown that applying systematic controls to as many variables as possible is the most successful approach for improvement in mining safety and health.When embarking upon the development of the CORESafety framework, NMA’s leadership set an ambitious goal to eliminate fatalities and reduce the injury rate 50 percent in five years, or the “0-50-5” goal. While the goal has not been met yet, the steady progress has been extraordinary with fatalities among participating companies dropping 45 percent during the period 2011-2015 (Fig. 2). Data also demonstrate that, as participating companies increase their level of implementation, total injury rates have also declined (Fig. 3).In a September 2015 interview with NMA, Penn State University mining engineering Professor Jeffrey Kohler praised CORESafety as “an inspired and timely program that brings together key elements to achieve safety and health goals.”"

Sep 1, 2016

By RIINA SALMIMIES, Paula Vehmaanperä, Antti Häkkinen

The dissolution of iron oxides in mixtures of acids is fairly uncommon but can result in a more efficient dissolution process. The objective in this work was to investigate the dissolution of synthetic hematite powder in mixtures of oxalic and sulfuric acid. Experiments were done at different acid ratios and temperatures. An increase in temperature from 15 to 35 °C increased solubility, whereas an increase from 35 to 50 °C did not change the solubility but had a profound effect on the kinetics. An important finding was that oxalic acid advanced the dissolution process since increasing the amount of oxalic acid in the system resulted in faster kinetics and higher solubilities. The dissolution kinetics were well described with the Kabai model, which was the only studied model able to describe the whole reaction time. However, the solid specific constant a varied for the different acid ratios and this is argued to be a result of changes in the solid phase. The changes in the constant a were not in line with the original study of Kabai, which indicates that a cannot be the solid specific constant but it can be the constant connected to dissolving media describing the changes in the dissolution mechanism.

Sep 23, 2020