Search Documents

By Michael Arnold, Jonathan Delgado

In 2017, Bauer Foundation Corp. (BFC) was awarded the contract to install the deep foundations for the new 17-story Hotel Tower and the Low Rise Casino Expansion at the Seminole Hard Rock Hotel and Casino in Tampa, Florida. The site was underlain by extremely challenging Florida Limestone geology and surrounded by occupied existing buildings and infrastructure. To overcome the challenges of the difficult subsurface conditions, and to successfully complete the foundation installation without impact to the surrounding buildings and casino operation, Langan Engineering (EOR) and BFC were required to modify both the design and installation techniques during construction. The scope of work included 147 temporarily cased drilled shafts to depths up to 230 ft (70 m) below ground surface (BGS), 76 permanently cased micropiles up to 200 ft (61 m) BGS, and more than 300 augered-cast-in-place (ACIP) piles up to 125 ft (38 m) BGS. Voids and zones of high permeability in the limestone created many challenges for execution of the foundation scope including ACIP piles overbreaks of more than 400% above neatline volume, and construction induced ground subsidence/collapses adjacent to structures supported on shallow foundations. This paper will discuss site limitations, design and construction challenges, difficult geology, varied soil conditions, and lessons learned. PROJECT The project is located at Seminole Hard Rock Hotel and Casino Tampa, Florida, as shown in Fig. 1. Seminole Tribe, the owner, started the construction of a new 17-story Hotel Tower and the Low-Rise Casino Expansion at the beginning of 2017.

Jan 1, 2018

By Mary E. Cocklan-Vendl

Regulatory processes associated with development of major mining operations in Alaska and British columbia were evaluated using specific case studies. Included were one hard rock mine in Alaska (Red Dog Mine), one hard rock mine In British Columbia (Snip Mine), and one offshore gold dredging project in Alaska (WestGold SIMA). Based on a comparison of the three case studies, it became clear that the primary incentives for cost effective permitting are: 1) early and continuing coordination of proposed project plans, designs and schedules with key regulatory agencies and local area residents and 2) development of a sufficient level of baseline information on air quality, water quality, wetlands, endangered species, fish and wildlife, and socia-cultural conditions to support the required permit application. The U.S. permitting process worked in much the same way as the Canadian permitting process. Disincentives of mine permitting include high initial costs for baseline data gathering. However, a relatively high early investment resulted in more efficient permit acquisition and reduced long-term monitoring requirements. A common problem Identified was the inadequate supply of trained agency personnel with the requisite technical and permitting experience. This sometimes resulted in poor decisions and unnecessary changes in project plans and schedules.

Jan 1, 1993

By D. Mohapatra

Extraction of Al(III) from aqueous sulfuric acid solutions into organic Cyanex 272®-carbon tetrachloride systems was investigated from a multi-component mixture containing aluminum, cobalt and nickel. Al(III) extraction efficiency was quantitative with 1.0 M Cyanex 272® in two stages at an aqueous: organic (A:O) phase ratio of 1:1 and an equilibrium pH of 3.2. The stripping of Al(III) from the loaded organic (LO) with different acids indicated sulfuric acid to be the best stripping agent. More than 99% stripping of Al(III) from the LO was achieved using 2 M H2SO4 at an A:O phase ratio of 1:1 in a single stage. The stoichiometry of the extracted species of Al(III) was determined by the slope analysis method. The extraction reaction proceeded via the cation exchange mechanism and the extracted species was assumed to be AlA3?3HA, where HA refers to the dimeric and A the anionic form of the extractant, Cyanex 272®. The extraction of Al(III) was studied in the presence of various ions to ascertain the tolerance limit of individual ions.

Jan 1, 2008

By J. W. Givens, P. B. Crawford

A potentiometric model study has been made of the effect of vertical fractures existing in the matrix of the reservoir on the flooding or cycling performance. Fractures can have unusual flow characteristics. Fluid entering one side of a fracture can emerge on either the same or opposite side of the fracture, depending on the particular streamline. Fracture orientation has a great influence on the sweep efficiency. However, sustained fluid injection may still permit large areas to be swept. INTRODUCTION One can find considerable information available in the literature on the effect of fractures originating at the wellbore on sweep efficiencies of water-flooding or gas cycling programs.1-5 However, there arc few, if any, quantitative data reported in the literature on the effect of vertical or horizontal fractures existing out in the reservoir matrix on secondary recovery performance. Several papers have been presented on the effect of vertical and horizontal fractures on the productivity or conductivity of waterflood and gas injection patterns, but in all cases the fractures initiated at the well and simulated commercial fractures.6,7 It is believed that natural fractures may exist out in the reservoir matrix and would effect the displacement performance. The purpose of this report was to study the effect of a few isolated vertical fractures existing out in the reservoir matrix on the performance of waterflood or gas injection patterns. DESCRIPTION AND EQUIPMENT Since the potentiometric model was described by Lee8 it has been widely used to study numerous types of fluid displacement problems. The potentio- metric model can be used for fluid displacement studies when the following assumptions are valid: (a) steady-state conditions exist; (b) the mobilicy ratio is one; and (c) the capillary and gravitational effects can be neglected. Five-spot and direct line drive square patterns were studied using a copper strip of the desired length and orientation to simulate a vertical fracture in the reservoir matrix. The 20 x 20-in. model was considered to represent only one element of an infinite array of similar patterns. DISCUSSION AND RESULTS FIVE-SPOT PATTERN — ONE FRACTURE BETWEEN INJECTION AND PRODUCING WELLS Fig. 1 shows a quadrant of a five-spot pattem with the vertical fracture existing out in the matrix along a line connecting the injection and producing wells. Length of the fracture was equal to 35.4 per cent of the distance between injection and producing wells. In this particular pattern it is noted that fluid breaks through from the injection well to the producing well when the dimensionless time is equivalent to 26.9. Dimensionless time is defined as volume of fluid injected divided by the volume of displaceable fluid in the pattem expressed as a per cent. The cross-hatched areas of this

Jan 1, 1967

By Jeffrey R. Hill

To extend the life of the Merchants Railroad Bridge crossing the Mississippi River in St. Louis, MO, the owner implemented a rehabilitation and reconstruction project. The Merchants Bridge provides a key link in the transcontinental railroad system. The bridge is of local importance to the Terminal Railroad Association ? providing a link between St Louis and a rail switching yard in Venice, IL. The intent of the bridge rehabilitation is to keep the Merchants Bridge in service, even though the bridge was originally constructed in the 1890?s. The project involved replacing the East and West approach deck truss spans with new deck girder spans. The rehabilitation program required construction of new concrete piers to support the new spans. In order to reduce the track down time to two, ten day single track shutdowns, the specifications required that all foundation and substructure work be completed while leaving the existing spans in place. The preliminary bridge design specified rock-socketed drilled shaft foundations. Drilled shafts proved to be challenging due to working from beneath the existing bridge, a high water table, utilities, a flood wall, and existing rail way lines. The micropile alternative was technically appropriate given the access limitations, shortened the foundation rehabilitation schedule by several weeks, and realized a significant cost savings to the Owner.

Jan 1, 2006

By Claude Bazin, François Robichaud

"The control of the operation of semi autogeneous grinding (SAG) mills is mainly achieved through adjustments of feed rate, water addition and speed of rotation. With the introduction of image based sensors it is possible to have on-line measurements of the size distribution of the ore feeding a SAG mill. This information could be used for the development of a control strategy to regulate a SAG mill feed size distribution to a set-point. The control of the size distribution is carried out by adjustment of the speed of the ore extractors underneath the ore stockpile. The potential and difficulty associated with the implementation of such control are assessed using a multivariable statistical analysis of data collected from the operation of the grinding circuit of the Agnico-Eagle Goldex mine in Val d’Or, QC. A control strategy for the ore feed size distribution is assessed using a simulator of the ore stockpile operation.INTRODUCTIONThe popularity of autogeneous (FAG) and semi autogeneous (SAG) grinding mills has been increasing over the last 20 years (Napier Munn et al., 1996). These mills use the ore or a combination of ore and steel balls as the grinding media. Since the ore is used as a media for the size reduction the mill ore feed size distribution impacts the performance of the mill. Several papers were recently published on this subject (Dance et al.,2011; Wennen & Murr, 2011; Dance & Valery, 2011; Allaire et al., 2011) showing the advantages of preparing the feed size distribution to maximize the circuit throughput or mill efficiency (Wennen & Murr, 2011; Dance & Valery, 2011; Allaire et al., 2011). With the availability of particle size sensor based on image analysis of the ore on a conveyor (Partanen et al., 2001; Bobo et al. 2004; Edwards et al., 2002; Wei & Craig, 2009) it is possible to control the size distribution of the ore feeding autogeneous or semi autogeneous mills (Partanen et al., 2001).This paper describes a method to control a size distribution index to a set point via the manipulation of the speed of the extractors that withdraw the ore from the stockpile feeding the grinding circuit. The paper consists of 4 sections. The first section describes the considered grinding circuit. A statistical analysis of the collected data on the grinding circuit is presented in the second section. This analysis demonstrates the necessity of using real-time adaptation mechanisms to develop a control strategy for the size distribution of a grinding circuit. The third section describes the method used to simulate the ore stockpile operation and the last section describes the preliminary development and assessment of a control strategy of size distribution of the ore feeding a SAG mill."

Jan 1, 2013

Contents.SummaryIntroductionSituation, climate, topographyHistorySize of depositsPrevious investigationsGeological History of AreaMap compilationHistorical summaryNature and Significance of Granitic RocksSynchronous granitesMain subsequent granitesSignificance of types of bathylithsGeological StructureNorth-south anticlineCross-foldingFormation of channelwaysHydrothermal Depth-Zoning at CobarAssociation of Ores with PorphyryOrigin of replacement porphyriesTransgressive porphyriesSummary of ore-porphyry relationshipsSource of the Copper and GoldProspecting Targets, Cobar-NymageeGeneral ApplicationBroken HillThe Bendigo FieldKalgoorlie-Coolgardie, Western AustraliaConclusions

Jan 1, 1950

By J. H. East, D. Harrington

"INTRODUCTION Burning refuse dumps are a common and by no means pleasant sight in most coal-mining distracts; they have been and largely continue to be accepted as a necessary, if undesirable, adjunct to coal-mining operations. The odor, smoke, and fumes emanating from the burning dumps have caused much property damage, as well as aroused unfavorable public sentiment in the areas thus affected; and there is reason to believe that, in at least some cases, they have had an adverse effect on the health of certain communities, adjacent to mines. In some instances such communities have been owned or controlled by the mining companies and in others they are incorporated towns.After the start of World War II, it was necessary for Great Britain to take prompt and effective measures to extinguish or at least blanket the burning refuse dumps at collieries, since the fires served as beacons for the enemy planes; the problem thus became a matter of national security rather than one of local inconvenience. If the United States should become involved in a bombing war, these dumps might became a source of national danger, hence now is a propitious time to at least make a start on available methods of solving this problem. Much progress was made in Great Britain in extinguishing the dump fires that had burned for years and in preventing newly made dumps from taking fire.Burning refuse dumps have not been a national problem in the United States, but they are a nuisance and frequently a danger and often a fruitful cause of poor public relations on account of the odor and fumes. Many progressive coal-mining companies are taking effective and positive action in trying to extinguish old dump fires and to build new dumps so they are less likely to fire.The purpose of this paper is to provide information about the problem as well as on ways to extinguish refuse dump fires, to describe methods of constructing dumps that probably will prevent them from firing, and to point out some of the danger that exists when dumps are improperly built and when they are on fire."

Mar 1, 1948

By R. O. Williams

A recent article by Chernock, Singer, Mueller, and Beck 1 which supports the use of the integral of I sin $ d$ for comparing fiber texture data does not settle what happens to I sin ø as ø approaches zero, where I is the diffraction intensity for poles oriented 0 deg from the fiber axis. They indicate that they believe that it should approach some constant value (that is, I increases without bound) and the fact that in reality it does not was a result of the diffraction

Jan 1, 1960

By A. B. Parsons

Jan 1, 1971

By G W. Clamp

The most traum atic event within the lUK coal industry during the last 30 years was its privatisation. Who were the relatively unknown people from RJB: white knights or robber barons? This paper highlights the strong safety and progressive engineering cultures th at existed and continues within the company. A long-term view of the business coupled with proven professionalism is amply developed. Quite dearly, to revert to private ownership is not a return to Victorian values but ‘back to the future’.

Jan 8, 1997

By S. K. Murphy, S. M. Spottiswoode, A. M. Milev, D. Geyser

A portable, stand-alone instrument especially designed for recording strong ground motion was used in this study to create a large database of peak particle velocities measured underground. A total number of 39 sites located in stopes mining Carbon Leader and Ventersdorp Contact Reefs were investigated. Peak particle velocities whith values up to 3 m/s were recorded at some sites. The data recorded on the skin of the excavations were compared to the data recorded by the mine seismic networks to determine the site response. The maximum site response was obtained for source radii of between 5 m and 30 m and events locating within 200 m of the site. The extreme values of peak particle velocities were obtained in cases were the face-area lay within the source radius. Un instrument portable unique spécifiquement conçu pour enregistrer les mouvements dynamiques des terrains, a été utilisé dans cette étude pour créer une base de données importante sur la vélocité maximum des particules, mesurée en souterrain. Un nombre total de 39 sites situés dans les excavations exploitant les récifs appelés ‘Carbon Leader et Ventersdorp Contact Reefs’, a été investigué. Une vélocité maximale avec des valeurs allant jusqu’ à 3 m/s a été enregistrée sur certains sites. Les données enregistrées sur le bord de l’excavation ont été comparées aux données enregistrées par les réseaux séismiques de la mine pour déterminer la réponse du site. La réponse maximum du site a été obtenue pour des sources de rayons entre 5 m et 30 m et des évènements situés dans les 200 m du site. Les valeurs extrêmes de vélocités maximales ont été obtenues pour les cas où la zone de face se trouve à l’intérieur du rayon de la source. Ein mobiles, alleinstehendes Instrument, speziell entworfen um starke Formationsbewegungen aufzuzeichnen, wurde in dieser Studie verwendet um eine große Datenbank von Partikelspitzengeschwindigkeiten, die Untertage gemessen wurden, aufzuzeichnen. Eine Gesamtanzahl von 39 Aufstellungsorten in den Schichtabbauorten vom Carbon Leader und Ventersdorp Contact Reef wurden untersucht. Partikelspitzengeschwindigkeiten mit Werten bis zu 3 m/s wurden an einigen Standorten aufgezeichnet Die an der Oberfläche des Grubenraumes aufgezeichneten Daten wurden mit jenen Daten verglichen, die vom seismischen Netzwerk der Grube notiert wurden, um die örtliche Reaktion des Standortes zu bestimmen. Die maximale Standortreaktion wurde für Ursprungsradien von zwischen 5 m und 30 m erhalten und Ereignissen die sich innerhalb von 200 m vom Standort befanden. Die extremen Werte der Partikelhöchstgeschwindigkeiten wurdenin jenen Fällen erreicht wo sich der Abbaubereich innerhalb des Ursprungsradiuses befand.

Jan 1, 2003

Understanding multiphase particulate systems is essential for the further advancement of mineral processing technology. Characterisation, analysis, and simulation of these complex systems provide a fundamental basis for the development of improved mineral processing technology. One of the more recent tools that can be used to help provide a foundation for improved mineral processing technology is high resolution cone beam X-ray micro computed tomography (CT). During the past ten years point-projection X-ray micro CT systems have been used for 3D visualisation and quantitative analysis of multiphase particulate systems. Analysis of packed particle beds containing as many as 30 000 particles can be accomplished in less than three hours with special software to establish the 3D characteristics of each particle in the population and the spatial organisation of the packed particle bed. Now, due to advances in X-ray optics, the resolution afforded with point-projection micro CT systems has been improved by at least an order of magnitude using a lens-based X-ray micro CT system. The development of software tools for the 3D characterisation, analysis, and simulation of packed particle beds using high resolution X-ray micro tomography (HRXMT) is discussed including examples of application in the areas of comminution (particle damage and preferential grain boundary fracture), exposure/liberation analysis (liberation-limited separation efficiency, including coal washability), and filtration/heap leaching (pore network structure of packed particle beds and simulated flow using the LB method of computational fluid dynamics).

Sep 13, 2010

By M. Dworzanowski

The beneficiation of fine iron ore will increase in importance in the future because most new iron ore resources will be in the form of lower grade ore deposits that will require liberation of iron ore minerals at finer sizes. Generally this fine iron ore will be beneficiated to produce a pelletizing concentrate with very strict chemical and physical specifications. In addition, because of the increasing demand for iron ore there are now more opportunities to produce by-product iron ore from mining operations producing other commodities. In the past the associated iron ore minerals would report to final tailings but now there is potential value to be realised from by-product revenue. These by-product iron ore opportunities are almost all centred on producing pelletizing concentrate. Currently pelletizing concentrates are produced mainly by various combinations of flotation and magnetic separation. The selection of the beneficiation route will depend on ore mineralogy and considerations around plant capacity and final concentrate quality. The main economic iron minerals are magnetic, haematite being paramagnetic and magnetite being ferromagnetic. This, therefore, means that magnetic separation can be applied, in principle, to all fine iron-ore beneficiation plants. While flotation has a considerable capacity advantage over magnetic separation, the real advantage of magnetic separation over flotation in fine iron-ore beneficiation is that treatment of -10 µm iron ore is possible-in flotation, the feed is deslimed at 10 µm and the -10 µm stream is considered to be final tailings, even though there is often a significant amount of contained iron ore. This paper describes a study around the recovery of fine magnetite in the form of a pelletizing concentrate. The study is based on an evaluation of an iron ore by-product opportunity from an iron oxide copper-gold (IOCG) deposit. Experiments were conducted to quantify the differences in magnetic separation performance with decrease in particle size treated. A mineralogical evaluation of all the test work products was undertaken to facilitate the interpretation of the test work results. These results were then used to propose an economically viable flowsheet for maximizing fine magnetite recovery using magnetic separation.

Jan 1, 2012

By Y. C. Liu

Both the habit plane of martensite and the orientation relationship between the matrix and martensite platelets of different habit planes have been investigated in binary titanium alloys with molybdenum, chromium, and iron. The effect of the mode of deformation on the martensite habit plane was studied. A micrograph of an exposed mar-tensite platelet is presented. IN the study of martensitic transformation in Ti-Mn alloys,' two martensite habit planes—{334), and {344)8—were reported. The {334), habit was also observed in unalloyed titanium upon transformation,' although there is disagreement with respect to the exact indices. The other habit plane, {344),, has not been reported in martensitic transformation in any other alloys. The present investigation was made to determine whether other binary titanium alloys with P-stabil-izing elements would exhibit a crystallography of transformation similar to that of Ti-Mn alloys. Furthermore, since martensite platelets can be induced by deformation under certain conditions, it was of interest to investigate whether the mode of deformation, compressive or tensile, would influence the formation of martensite platelets on a specific plane in an alloy system which possesses two martensite habit planes. Experimental Procedure The material used for the preparation of the binary alloys of iodide titanium with molybdenum, chromium, and iron had the following purities: 99.99 pct iodide titanium, 99.9 pct molybdenum, 99.423 pct chromium, and 99.9 pct iron. The compositions of alloys listed in this paper are in nominal weight percentage. All specimens used were prepared and treated according to the procedure described in reference 1, unless stated. For the subzero temperature treat,ment the following experimental schedule was followed. After specimens had undergone the grain-growth treatment, they were quenched into an ice-water bath and were then metallographically examined. In specimens of higher alloy content, no martensitic transformation was observed. In those in which mar-tensitic transformation did occur, only specimens in which the martensite platelets existed as fine needles in localized regions were used. All specimens were reannealed 17 hr at 1200°C, quenched into ice water. and the capsule was broken. They were held in the ice water for from 5 to 10 sec, then transferred to a liquid-argon bath. This stepped quenching procedure was found to be more efficient than direct quenching into liquid argon. In the latter case, as soon as the hot specimen was immersed in the liquid argon, a protective, insulating layer of argon gas formed, and the specimen continued to glow vividly in the bath for some time. In the study of the habit behavior of martensite produced by deformation, specimens were deformed at room temperature either by compression, tension, or rolling. Martensite habit planes were determined by the two-surface analysis procedure described in reference 1. A stereographic net of 153/4 in. diam was used throughout the investigation. The method for determining the orlentation relationship between martensite and the matrix follows that used by Greninger and Troiano.' A diamond-polishing table with its auxiliaries was used in order

Jan 1, 1957

By M. Mostert

Mining companies sponsor a range of non-core, corporate social responsibility projects to adhere to social and labour plans and environmental management prerequisites that form part of a mining licence application. Some companies go above and beyond such projects, sponsoring initiatives that generate renewable energy through solar power, wind energy, natural gas, etc. The challenge for these companies is to choose between a variety of projects to ensure maximum value, especially in times when the economic climate might be less favourable for such projects. The focus of this research was to analyse the concept of sustainability as it exists today, and to apply that to the triple bottom line accounting method in an attempt to quantify the sustainability of a project. Research was done on the methane burn-off project at Sibanye Gold?s Beatrix Mine to establish how such projects are planned and financed, and what impact they have on the triple bottom line of a company. The financial bottom line is, by definition, one that executives understand. This paper also proposes a quantitative method for defining the social and environmental bottom lines as well. By considering the financial, social, and environmental values, the study attempts to determine a monetary value for a sustainable renewable energy project. This monetary value can be compared to similar values obtained for other sustainable renewable energy projects under consideration. The research suggests that monetary value alone is not enough to base a sustainable decision on, and qualitative measures are suggested for use in conjunction with quantitative methods. The selection method proposed should assist the board of a mining company to choose the most sustainable option and the project that will add the greatest value to the company across all three bottom lines. It will also provide increased justification for such renewable energy projects, even in periods of harsh or uncertain economic climates.

Jan 1, 2014

By P W. Wypych, D Curry, A P. Grima

The market has become highly competitive for engineering and equipment vendors, who are challenged to reduce costs while improving efficiency and productivity of mine operations through plant improvements and expansions. Although conveyor transfer systems account for a small percentage of the infrastructure cost of a mine, they form an integral part of the process supply chain. Malfunctions or suboptimal performance can result in substantial financial cost from delayed start-up, unscheduled downtime, reduced throughput and increased maintenance costs.Discrete element modelling (DEM) is a powerful simulation method used to virtually prototype and test the performance of transfer equipment throughout a design cycle. When developed and applied correctly, DEM can provide insight into performance that exceeds the traditional analytical methods, especially when dealing with complex ore properties, behaviour and/or situations.Using case studies sourced from the authors’ recent research and industrial project work, this paper will address the industry goal to increase efficiency and productivity as well as the methods available to the engineers responsible for delivering designs that meet the aims of this strategic approach.The main focus of the paper will be the new calibration technology, which has been developed by the authors to generate DEM material models that are linked to real-world properties and flow behaviours via unique dynamic testing and innovative parameter calibration methods. These calibrated DEM material models can be deployed by engineers into their existing workflows, whether it be for feasibility studies, concept or final design, plant troubleshooting or optimisation.This new technology allows engineers to gain greater insight than that provided by traditional approaches to the design of transfer chutes and other process equipment and also allows informed design decisions to be made that meet industry efficiency and productivity requirements.CITATION:Grima, A P, Curry, D and Wypych, P W, 2015. New discrete element modelling calibration technology to facilitate the increased efficiency of ore handling and processing operations, in Proceedings Iron Ore 2015, pp 449–464 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By James F. Archibald

In historic mining practice, typical thin liner support systems have been considered to comprise non-reinforced or mesh-reinforced shocrete linings. In the early 1990?s, development of alternate forms of liner systems was initiated in Canada which is now undergoing significant international growth in countries which sustain major mining activity. Now internationally designated as thin, spray-on liner systems, a wide spectrum of liner materials, ranging from liquid/liquid to liquid/solid component combinations, has become commercially available. This innovative family of products is characteristically identified as being rapidly deployable, capable of creating ultra-fast setting coverage over rock surfaces, and able to develop tenacious adhesion and pull strength capacities for resisting rock falls and movements. This paper presents a summary of current liner developments and use in principal mining districts world wide. Additionally, a database of material properties for principal product types used in mining and a review of common quality control testing procedures under development are provided. Such information is based upon recent Canadian and international efforts being taken to assess and develop user standards for the implementation of thin, spray-on liners as rock support in mines. This work is intended to continue for a period of years, with the eventual goal being to establish support and installation guidelines for mines based on quantifiable laboratory and field research.

May 1, 2002

By R. E. Wilmot

The problem of corrosion of reinforcement in concrete structures is internationally recognised and represents the single biggest expenditure in the preservation of steel reinforced concrete structures. While the corrosion protection of the reinforcing steel is no substitute for design and the placement of good quality concrete, it does provide for a viable and economical extension of structural integrity and service life in the day-to-day and practical environment in which concrete structures are constructed. The mechanism of corrosion attack and consequent deterioration of reinforced concrete structures is well understood and documented. New structures can be designed and built to withstand corrosion. However, due to short-term economical restraints, many new reinforced concrete structures continue to suffer as a result of corrosion damage, which results from the corrosion of the steel reinforcing. This paper explores the economic and practical benefits offered by the application of hot dip galvanizing as a viable means of protecting reinforcing steel concrete structures. The paper also discusses technical misconceptions that exist with respect to the application and performance provided by the use of hot dip galvanized reinforcing steel.

Jan 1, 2006

By D. K. Bose, R. H. Rakhasia, V. D. Shah, J. C. Sehra

A series of experiments was conducted to determine the effects of roasting temperature, soaking period and quantity of soda ash added. At a laboratory scale, under optimum conditions of roasting at 873 K for 2 700 s with soda ash 10 wt% in excess of stoichiometric, molybdenum recovery was 99%. The investigations indicate the technical feasibility of producing high-purity MoO3 by combining the roasting process with carbon adsorption/desorption. The process uses low-cost chemicals, can be scaled up readily and is free of the SO2 pollution generated by conventional roasting, as the sulphur content of the concentrate is converted to sodium sulphate

Jun 18, 1905