Search Documents

By Thierry Bernard, Guy Gagnon

Blasting at very close proximity to urban areas is typically a situation where both local communities and mining stakeholders get nervous. The context becomes logically even more tensed when the blasting operations have to be performed above an old underground mine. When mitigating subsidence risks requires firing the largest possible shots, the nuisance control (flyrock, vibration, and noise) required by local and national regulations, contrarily urge for being more conservative.

Jan 1, 2014

By Thompson D. R, Milton R, Perry K. M A

From the Department for Research in Industrial Medicine (Medical Research Council), The London Hospital; and the De Havilland Aircraft Company:M.R.C. INVESTIGATIONS IN 1936In 1936 the Industrial Pulmonary Disease Committee of the Medical Research Council investigated both clinically and radiologically a group of fifty workers who had been exposed for a number of years to the inhalation of alumina in the reduction factory of the British Aluminium Company. The results are shown in Table 1.They also considered the sickness records of all the workers (Hill, 1936), as compared with those in other parts of the factory (Table 2).

Jan 1, 1945

By Norman F. Schulz

The technical excellence of separation achieved in a mineral concentration process, or any other process where two constituents of any kind are physically separated from each other, is expressed uniquely and quantitatively by the separation efficiency (E,): E. = (R - R,), where R is the percentage of the valuable constituent and R, the percentage of the waste appearing in the concentrate. The separation efficiency meets all the usual requirements of a true efficiency and is independent of the nature of the process used. It can be visualized as the percentage of the feed material that, in effect, actually undergoes complete separation while the rest of the feed is distributed randomly and unchanged into the two separation products. The problem of quantitatively assessing the results of a mineral concentration process recurs whenever one tries to decide which of two similar test results is more desirable. Although economic factors may greatly influence the eventual choice of process, they usually have very little to do with the technical excellence of a separation and are, therefore, not a consideration at this point. Concentrate grade and recovery, used simultaneously are the most widely accepted measures of performance, and if both the grade and the recovery are greater for one case than for another, the choice is simple. However, when the results of closely competitive operations are compared, it often occurs that one set of test results shows a higher grade and a lower recovery than another and the choice is no longer obvious. Laboratory investigations of a mineral concentration process applied to a given feed material can often be designed to yield successive paired values of concentrate grade and recovery over the practical range of the course of a separation process.' These results may be plotted as some combination of the cumulative values of grade, weight recovery, or unit recovery in the concentrate. The resulting correlations for two slightly different sets of conditions can then be compared qualitatively, or even quantitatively in particular cases.2 Such comparisons are not applicable, however, to individual concentration test results. The reduction of a separation test result to a single efficiency figure, preferably as a percentage of ideality, would afford the simplest and most precise means for comparing the results of competitive tests. The effective proportion of feed material that undergoes complete separation in any real concentration process, hereafter referred to as "separation efficiency," is such a figure. It is essily calculated from the usual feed and product data and can even be evaluated, in many cases, from data in publications describing various concentration processes. Mineral Concentration Processes and Their Evaluation Mineral Concentration Processes: The overall concentration process may be subdivided into a liberation process which severs the bonds between unlike mineral species, and a separation process, which sorts the resulting liberated particles into two products—a concentrate rich in mineral A and a tailing lean in mineral A. A perfect mineral concentration process is represented by the idealized scheme shown in Fig. 1 in which liberation and separation are not differentiated. The feed mixture consists of two mineral types which are completely liberated early in the process and then sorted by type. All the mineral particles of type A which respond uniquely to the selection forces acting in the ideal separator, report to the concentrate, while all the mineral particles of type non-A report to the tail-

Jan 1, 1971

By R. L. King

This report describes a method for designing and constructing ground beds that has been developed under the sponsorship of the Bureau of Mines. The procedures for designing and constructing a driven-rod ground bed with a resistance of 5 ohms or less are given. Some of the theory of soil resistivity and fall-of-potential resistance measurements is included. Results of a bed constructed at the Bureau of Mines mine car roadway are presented.

Jan 1, 1978

By Randy Reed, Barbara J. Arnold

Respirable crystalline silica poses a significant health risk, with the American Lung Association estimating that 2.3 million workers are exposed to silica in the workplace. This includes mine workers as well as those in many other industries. Reducing dust formation is sometimes not possible so other methods to reduce exposure are critical. These methods include the use of surfactants to reduce airborne dust particles. However, it is the proper selection and application of surfactants that leads to reduced dust exposure. A discussion of how surfactants work, especially for silica dust, leads to guidance for surfactant selection followed by a review of technologies for their application.

Feb 1, 2024

By R. Ribacchi, P. Tommasi, C. Consorti, P. Campedel

The runout of dry blocky rock avalanches produced by planar rockslides affecting a limestone formation with clayey interbeds is analysed by means of distinct element modelling. Numerical analyses are validated by means of the back analysis of a historical rockslide occurred in the investigated area and physical aspects of the phenomenon evidenced by modelling are discussed. On analyse par la méthode aux élements distincts la distance de parcours des avalanches rocheuses sèches produites par des glissements plan interessant une formation de calcaire à intercalaires argilleux. Les analyses numeriques sont validées à l’aide de la back-analysis d’un glissement historique survenue dans le site en examen. On décrit les aspects physiques su phénomène mis en évidence par la modélisation efféctuée. In diesem Beitrag wird die Reichweite von Steinlawinen besthend aus trockenem blockhaftem Fels mittels der Distinct Element Methode untersucht. Die Steinlawinen werden erzeugt von Rutschungen in einer Kalkstein-Formation mit tonhaltige Schichten betreffen. Die numerischen Berechnungen wurden anhand einer Simulation einer historischen Bergsturzen verifiziert, der sich auf den untersuchten Gebiet ereignete. Auf der Basis der erhaltenen Ergebnisse wurden die physikalischen Aspekte der untersuchten Steinlawinen analysiert.

Jan 1, 2003

By J. Don Scott

Analytical predictions of the rate and magnitude of settlement of deposited oil sands tailings slurries generally overestimate how fast pore pressures will dissipate. Field deposits of nonsegregating tailings to mature fine tailings show continued high pore pressures near the surface which impede surface reclamation. In geotechnical analyses which predict the consolidation behavior of soft soils a finite strain theory is used. Effective stress-void ratio and void ratio-hydraulic conductivity relationships determined from laboratory large strain consolidation tests, are used in the finite strain predictions. This theory, however, cannot predict the full range of sedimentation, consolidation and pore pressure dissipation which occurs in large scale deposits of thixotropic tailings slurries. A new large strain consolidation model which assumes that the creep rate of the slurry exceeds the pore pressure dissipation rate is being investigated. This model is relevant for rapidly deposited, low permeability thixotropic slurries where the upwards drainage path increases by several meters a year, such as, in oil sand fine tailings ponds and nonsegregating tailings deposits. The model will be verified by analyzing the 10m high column of fine tailings at the University of Alberta which has been monitored for over 20 years and in which the excess pore pressures are still very high.

May 1, 2004

By Victor V. Nazimko

Multiple mining generates gob-interaction displacements. They redistribute stress m strata and obey laws of irreversibility thermodynamics. An irreversible state causes inhomogeneity of the stress distribution on the mass. A destressed zone develops along a working panel, and worked out panels are deprived of the destressing. The inhomogeneity is smoothed out during elapsed time.

Jan 1, 1996

(This paper reviews the reasons for and the principles followed in designing and constructing complete new surface works at the mine of the Zinc Corporation Limited, Broken Hill, New South Wales, and describes the layout, plant, buildings and services.)The Zinc Corporation mine produces high grade lead, silver and zinc sulphide ore. Lead and zinc concentrates are sent by rail to Port Pirie, where the lead is smelted and the zinc concentrate is shipped to Tasmania, England and other overseas countries.Some time ago consideration was given to the advisability of sinking an additional shaft. For some years the old main shaft had been working at full capacity and developments underground had indicated that the mine would eventually be capable of an output greater than that which could be handled through the shaft. It was therefore decided to sink a new main shaft and the site chosen was in footwall country 900 feet south of the old main shaft. The reason for the move south was so that the new shaft would be opposite the centre of gravity of the ore-bodies at depth. The size of the new shaft is 27 ft. ,6 in. x 15 ft., and the work was put in hand early in 1936.It was intended to haul the whole mine output through this shaft, which was 1,600 feet from the mill then operating. An extensive conveyor system thus became necessary unless a new mill was built near the shaft. A careful study of the situation was made by the management and consideration was given to requirements for expansion, the condition of...

Jan 1, 1940

This paper provides an overview of possible approaches for structuring the ventilation systems for mines that will become operational within the next decade. Features addressed in the paper include: aspects of airway design and layout in the absence of centralized vertical return shafts, the impact of using diesel-powered trackless equipment in conjunction with conveyor belts in the development and production phases of the project, and the need to balance increasing electrical power costs against the requirement for reduced capital expenditure. The paper provides brief descriptions of the strategies employed in real-life situations and presents an overview of various operational parameters affecting the design of ventilation systems that will be used as ?platforms? for much deeper mines in the future.

Jan 1, 2007

By M. G. Zabetakis, T. D. Moore

The use of a partially slotted 6.5-inch-inside-diameter vertical pipe to remove methane from a longwall gob area at a depth of 2,260 feet in the Pocahontas No. 3 coalbed ms investigated. The value of gas removed by such a pipe under free-flow conditions was found to equal the cost of the installation in this case. Approximately 25 percent of the available methane passed through the pipe without the use of an exhauster; an additional 10 percent was removed when an exhauster was employed. The diversion of methane through a vertical slotted pipe to the surface permitted the use of increased mining rates and decreased the ventilation air requirements.

Jan 1, 1972

With the exhaustion of orebodies close to the main haulage shaft of the Emperor mine, an increased rate of development, aimed at earlier investigation of values disclosed by exploration drill holes has been attained with an overall reduction in unit costs.This paper describes the techniques used in rates of advance up to and exceeding 1,000 ft per 28-day period.

Jan 1, 1966

By J. Hartikainen

Kemi cardboard mill is founded on the alluvial bed of Kemi river at the north-eastern cost of Botnic Culf in Northern Finland. The alluvium consists of sandy and silty layers underlain by thick medium dense silty moraine layer. The first cardboard machine, having a belt width of 7,4 m, was constructed in 1972 on 7,5 to 9,5 m long wedge-shaped precast driven piles. Because of the excessive differential settlements and sometimes unexpected dynamic malfunctioning of the machine it was decided to strengthen the foundation before installing the partly new machine and increasing the running speed from 500 to 750 m/min. Piling was done under extremly strick limitations concerning space, vibrations, settlements, dust etc. Extra vertical support was made by using 23...25 long x-form steel piles driven by compressed air pile hammer down to rock. The piles were held together with old piles by a conctrete frame with diagonals, which made the total system - machine - foundation frame, piles and ground - ridgid enough to avoid resonance during dynamic loading.

Jan 1, 2010

By R. P. Harvey, J. E. Walstrom, A. A. Brown

In view of the large number of wells directionally drilled from offshore platforms and urban drillsites, greater interest is being focused on the directional survey and on the uncertainty inherent in calculating the position of the bottom of the hole, or other benchmarks in the wellbore. Of the two methods presented here for evaluating this uncertainty, the first is analytical and uses the principles of probability and statistics. The second method uses Monte Carlo simulation to generate a pattern of the scatter of possible bottom-hole locations. Both methods are based on a model for which the usual assumption is made that the curvilinear axis of the wellbore is adequately represented by a large number, M, of linear segments joined end to end from the top to the bottom of the hole and closely following the course of the hole. The errors due to this approximation are assumed to be negligible and are not studied here. One form of the model is to consider that for a given hole there exists a perfect set of data describing it, of the above form. Each linear segment has an angle of inclination with the vertical 7, in radians, an azimuthal angle from true north xi in radians, and a length Si, in feet. The subscript variable, i, extends from 1 to M. Each of the M linear segments representing the axis of the wellbore has three components in the X, Y, and Z directions. These components are calculated from the equations: The bottom-hole coordinates as determined from the reference set of data for the wellbore are given by the following for i = 1 to M: X=SX, Y = Sy, Z=SZ; . (2) A directional survey instrument, lowered into the wellbore to the M segments, or stations, measures the values of the 7; and the 3,. In general, because of errors from various sources, the resulting angular measurements will not be precisely equal to the 7" and xi. Random variables l, and Ai are therefore considered with associated probability density functions fi(li) and gi(Ai), respectively, which represent the distributions of potential survey measurements for this hole. Since it is assumed that the values Si are accurately measured they are treated deterministically. The random variables corresponding to the surveyed bottom-hole coordinates are given, for i = 1 to M, by:

Jan 1, 1970

By Mazany, M. S.

THE Caletones copper smelter of the Braden Copper Co. is in the " Teniente" mining district about SO km. (49.7 mi.) southeast of Santiago, Chile. From the seaports of San Antonio and Tralparaiso, the property is reached via the Chilean State Railway (66-in. gage) to Rancagua, whence the Braden railroad (30-in. gage) leads to the smelting plant at Caletones, 60 km. away at 5100 ft. elevation, and continues on to the mine and concentrator at Sewell, at 7000 ft. elevation, 12 km. farther into the Andes. The smelting plant was completed and put into commission in February, 1922. At the start, it smelted daily 750 tons of concentrates produced at Sewell from 10,000 tons of ore; later, its capacity was increased to 900 tons of concentrates from 12,000 tons of ore per day; and it is now being increased to 1100 tons of concentrates from 15,000 tons of ore per day. The smelting plant production is governed chiefly by the

Jan 1, 1925

By D Connelly

There is now a new generation of mobile crushing and screening plant systems available which have been developed based on the motivation of reducing truck haulage. Newly designed mobile crushing and screening plant systems have the advantages of mobility, flexibility, economy and reliable performance, making this system very appealing for small- to medium-sized projects or projects where a number of resources are separated by distance.A brief review of the past history and experience with transportable crushing plants provides an insight into some of the issues with transportable plants in mineral processing. A closer look at a simple model based on exploiting small but high-grade orebodies suggests the concept has merit, however there are many more engineering, logistics, legal, technical and management aspects which have limited the application of such a concept in the resource sector. This paper explores the concept in detail and endeavours to analyse the preferred commodities and scenarios under which the concept could be used and the economic and logistical limitations for iron ore. The paper also looks at the risk assessment criteria to be applied in selecting the type of resource projects where the model could be applied successfully. Other aspects considered in this paper are the project planning requirements, technical and economic feasibility, bankability and operability. Reference is made to the operating experience of contractors at a number of sites and feedback from the resource companies as managers of the projects.CITATION:Connelly, D, 2013. Mobile crushing and screening plant applications for small- to medium-sized iron ore projects, in Proceedings Iron Ore 20 13, pp 349-354 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By K. D. Dill, S. D. Rosenthal

"This project analyzed the efficiency of incorporating the use of directional drilling technology into coal overburden blasting. Directional drilling is currently in use in the petroleum industry and it is believed that it will be a valuable asset in the mining industry. This project has shown that directional drilling can be a viable technology for use in the coal overburden removal process resulting in increased drill utilization and potential for cost savings. Future work regarding blasting and geotechnical evaluation should be performed to solidify the concept. INTRODUCTION Determine the Potential Drill Utilization Improvements and Rock Fragmentation Requirements Using Directional Drilling in a Coal Mining Overburden Highwall Application was a project funded by Atlas Copco Drilling Solutions (Atlas Copco) based in Garland, Texas. The project was developed and researched by Montana Tech of the University of Montana. This project was intended to show how the use of directional drilling can increase drill utilization, while decreasing costs, without sacrificing overburden blasting results. This paper discusses a review of the literature, the methods performed, conclusions and future work Background Atlas Copco theorized that an alternative approach to drilling a cast blast pattern would be beneficial to coal mining operations by increasing drill utilization and therefore, decreasing overall costs. Increasing drill utilization results in an increase in the amount of time the drill is being productive, more drill bit time in ground. Atlas Copco’s theory is that by incorporating directional drilling in the design of a cast blast pattern, a drill rig could drill multiple directional holes, which are the length of the cast blast, from a single drill set up. A drill goes through a series of steps to complete a blast pattern, these steps include: tramming to the hole location, leveling the drill, drilling the hole, cleaning the hole, and retracting the drill steel. This process is repeated hundreds of times until the whole pattern is completed. The most time intensive part of this process is drilling out the blast pattern. Integrating directional drilling into this process could decrease the overall time it takes to drill out a blast pattern by minimizing the amount of time spent tramming and setting up for each subsequent hole. Tramming and drill set up are two aspects of the drilling process where the drill tool is not engaged with the ground and, therefore, not being utilized. A cast blast pattern designed to utilize directional drilling will allow the drill tool to be “in the hole” longer and will improve drill utilization. This change in drill utilization was analyzed. Drilling and blasting is an integral part of the mining process, without it mining would be a slower process and less material could be mined. Drilling provides holes for explosives to be loaded and then blasted. Blasting has been found to be the most cost effective method of fracturing rock in mining for material removal. Blasting is also used as a low-cost method to move the rock in open cast mines, commonly referred to as cast blasting. A cast blast is a large blast designed to allow for the maximum amount of overburden to be removed using explosives in a single blast thereby uncovering more coal at a lower cost. Not all the material is blasted to cast-to-final, which requires that material to be moved with large mining machinery. Material that is considered cast-to-final is material that has been thrown far enough to never be moved again in the coal extraction process, therefore it is in its final resting place. A typical cast profile and cast-to-final area is shown in Figure 1."

Jan 1, 2017

There are available today many various types of mixing systems, tank types and process liquors confronting the process designer of gold adsorption circuits. This short paper is to give the process designer an insight into the special mixing requirements for resin-in-leach and resin-in-pulp, plus the advantages and disadvantages of the various mixing systems that are available to agitate the required tank shapes. An understanding of the latest developments in this important process area of gold production is addressed and information given on the results of resin degradation in various tank sizes over long periods of mechanical agitation.

Jan 1, 2007

By E. M. Cohn

The literature dealing with the electrical conductivity of solid dielectrics, including all its aspects and its relationships to other physical properties of these materials, is extensive and scattered in many books, phamphlets, and periodicals. It is believed that most of the important contributions to this field up to October 1943 have been listed and abstracted in this circular. Also included are some general references on static electricity. Methods of removing static charges are described; methods of and conditions for measurements of resistivity are discussed; equations for the calculation of resistivity are given; and methods of resistance measurements in Situ are reviewed. Data on the variations of resistivity with changing conditions as well as explanations for them have been collected, and three tables showing the resistivity of various dielectrics at different humidities are included. The appendix contains a short development of the mathematical formulation of the charging and discharging currents due to interfacial polarisation. INTRODUCTION Methods for Removing Static Electricity Of the various means employed for preventing or removing accumulations of static electricity in industrial processes, grounding is the most common and most generally effective. It is a precaution readily applied to stationary machines anti may often be utilized to good advantage to rid persons and portable equipment of an acquired charge. There are many situations, however, in which direct low-resistance grounding cannot be used, either because the charged bodies are insulators or are inaccessible, or because contact to a ground lead might give rise to a hazardous spark. If the charged body is a conductor, contact made to a neighboring conductor, even though the latter be insulated from ground and of relatively small capacitance, may also result in the occurrence of an incendive spark. In such instances, static electricity can sometimes be removed most satisfactorily by means of strong atmospheric ionization produced by radioactive material, X-rays, ultraviolet light, or A. C. high-voltage brush discharge. Where no danger exists from flammable

Jan 1, 1944

By Charles E. Semler

The possible utility of selected compositions in the systems SrO-ZrO2-MgO and SrO-ZrO2-Dolomite for commercial refractory products was confirmed in this study. Specifically the compositions of interest are located in the sub-systems SrZrO3-ZrO2-MgO and SrZrO3-ZrO2-Dolomite. Both sub-systems have regions that are not affected by hydration, but the sub-system SrZrO3-ZrO2-MgO has a larger candidate compositional region. Solid state phase relations were determined for the subject systems over the temperature range 1600°C to 1300°C, with compatibility diagrams presented for each. The systems appear to show good refractory character with no apparent low melting compositions. As the compositions of commercial interest lie mostly in the higher ZrO2 portion of each system, information is presented regarding the firing treatment required to develop stabilized cubic ZrO2. A list of suggestions for further study of these systems, to further delineate the characteristics required for possible commercial utilization, is presented.

Jan 1, 1982