Search Documents

By Sayan Sarkar

HAMR (Hydrogen Assisted Magnesiothermic Reduction) process is a promising alternative route of titanium production, which is convenient due to reduction at relatively lower temperatures below 750 °C and usage of cost-efficient TiO2 as the starting material. A crucial step involved in this process requires the Mg reduction of TiO2 subjected to H2 atmosphere which produces porous TiH2 along with residual magnesium impurities. Before the final heat treatment and deoxygenation steps for consolidation of the Ti powder, leaching plays a significant role in the removal of Mg impurities. In this report, we present a systematic study on the role of acid concentration (HCl), temperature and the kinetics of MgO dissolution. In addition, we also report the controlling mechanism during kinetics of MgO dissolution in acid. This parametric study will provide a platform to ensure very low Mg content that meets with ASTM standards during production of Ti in the HAMR process.

By Edward P. Hagarty

The Hazardous and Solid Waste Amendments (HSWA) of 1984 added Subtitle I to the Resource Conservation and Recovery Act (RCRA), authorizing the Environmental Protection Agency (EPA) to develop and implement a new regulatory program for Underground Storage Tanks (USTs) containing petroleum and other regulated substances. Technical standards required for release detection, prevention, and correction as necessary to protect human health and the environment were promulgated as described in 53 Federal Register 37082 (September 23, 1988). Virginia State Regulations (VR 680- 13-02) and U.S. Army Regulations require that a Corrective Action Plan and a Site Clearance Report be prepared to explain the details of remediation of any contaminated media. Construction of new buildings is proposed in two different areas at Fort Myer in Arlington, Virginia, where USTs containing gasoline, diesel and heating oil were located. Tightness testing performed on these USTs in September 1991 indicated that some of the tanks were leaking. Many of the tanks were removed for permanent closure. Initial Abatement (excavation of contaminated soil) was &ed out immediately. A detailed Site Characterization Study which included Hydropunch", field screening using immunoassay, and pilot test - dual phase (water and soil gas) extraction was conducted. Environmental media were analyzed for volatiles, semi-volatiles and metals. A detailed risk analysis (RA) was performed to determine risk-based clean up levels for benzene, toluene, ethylbenzene, xylenes (BTEX); polycyclic aromatic hydrocarbons (PAHs); and methyl-tertiary butyl ether (MTBE). The RA also discussed the presence of lead in the soil. Before constructing any buildings in these contaminated areas, remediation must be conducted in accordance with the State, Federal and other applicable regulations. The remedial alternatives evaluated included Vapor Enhanced Groundwater Extraction, Soil Vacuum Extraction, Soil Washing, Soil Steaming, Active and Passive Ventilation SolidificationlStabilization, Vapor Barrier Construction, and Excavation with Off-site Disposal. This paper discusses: (a) delineation of soil contamination @) risk analysis (c) evaluation of remedial alternatives and selection of the most appropriate technology and (d) consideration of various regulatory issues.

Jan 1, 1994

By Francis C. Furman

Microscopic evidence indicates that the high sinterability of certain commercial dolomites is tied to specific dolomite textural characteristics. This study encompasses detailed characterization of the unprocessed dolomite and sintering doloma results. The chemical and mineralogical compositions, insoluble residue, chemistry homogeneity, crystal size, primary carbonate texture, secondary dolomite texture, deformation structure, porosity type, porosity, and density of the raw dolomite were observed. These characteristics are compared with sintering trials of <74um powder-compacts samples in which holding times were varied. The evolution of the dolomite characteristics are reviewed and related to the final sintered doloma characteristics. The critical characteristics of a single-stage sintering brick dolomite are the following: 1) primary oolitic texture, 2) dolomite purity, 3) dolomite stoichiometry 4) minimal impurities, less than 1 weight {%} Fe2O3 Al2O3 and SiO2, 5) chemical homogeneity, 6) high density, 7) very low porosity, S) very coarse homogeneous crystallinity, 9) nonplanar dolomite texture, 10) abundant strain related slip microdeformation structures, 11) minimal subsequent alteration. Even with grinding to <74um the nonplanar dolomite texture and slip deformation still have a major effect on doloma sintered density. The three newly identified characteristics of single-stage sintered refractory brick dolomite are their primary oolitic texture, secondary nonplanar texture and abundance of stress related microdeformation structures. The primary oolitic texture reflects a homogeneous pure carbonate with respect to chemistry and crystal size secondary nonplanar texture produces crystals with large surface area to volume ratio. Stress related slip deformation moves CO, groups in to the same site of another CO, group but different orientation which is very unstable. All of these characteristics may facilitate the formation of higher density dolorna sinters.

Jan 1, 1995

By Mark R. Jolly, Jean-Christophe Gebelin, Aleksander Cendrowicz

"Injection of wax patterns is the first stage of the multi-stage process of investment casting. The quality of the final casting and its dimensional accuracy is highly dependent on this stage of the process. Pattern waxes used in the industry behave in a complex visco-elastic-plastic manner. The modelling of such material behaviour is therefore not simple.In this paper a number of configurations of die will be shown in which the injection of the wax has been carried out for a range of processing conditions. Some of the dies are transparent and the movements of wax front observed can be compared with those predicted by simulation. Surface defects in final components will also be shown and compared with the location predicted by simulation software. Some discussion will be presented on the limitations of the software used and the time-scales achieved for practical use as a design tool within the foundry environment. IntroductionThis paper presents the research activities carried out at the University of Birmingham on the modelling and prediction of the behaviour of industrial investment casting waxes during the injection of wax patterns. These research activities are done in the context of a more global study of the fundamental aspects of the investment casting process, the FOCAST project. Regarding the wax injection process, the aim of the project is to achieve a better understanding of the key factors that will lead to better castings. The filling of the die during the injection has been studied. Some other phenomena such as shrinkage/warpage or creep under residual stresses are also studied, but not presented here. Two commercial investment casting waxes have been characterised in order to model their behaviour and predict mould filling and subsequent defects.This paper will present the models that have been used in our work, the simulation packages used, the experiments carried out to validate the modelling and exhibit the defects due to bad filling, and finally the numerical simulation results."

Jan 1, 2001

By Jari Aromaa, Antti Kekki, Olof Forsén

"The deposition of copper on inert substrate depends on the number of active sites that will react at certain overpotential. The critical overpotential depends on surface morphology, surface film resistance and additives on cathode surface. The effects of surface properties on copper nucleation and growth rates were studied for used stainless steel blanks from several tankhouses. The surfaces of the blanks were characterized with electrochemical and mechanical methods. Electrochemical deposition tests were done at current density of 300 A/m2 for 10, 30 and 60 seconds. The nucleation density and copper coverage were estimated using image analysis. The surface film resistance did not correlate with copper growth. Increasing surface roughness correlated with lower copper growth.IntroductionStainless steel cathode blanks in copper electrorefming are usually made of AISI 3 I6L type steel. They have a typical lifetime over 10 years. During use the surface will collect deposits and become rough due to wear and corrosion. These factors can affect the nucleation and growth of copper. The nucleation and deposition of copper on inert substrate depends on the number of active sites that will react at certain overpotential. The critical overpotential can depend on surface film resistance, surface morphology, and additives adsorbed on cathode surface.The deposition potential of metallic ions on a foreign substrate is usually higher than the deposition potential on the electrode made of the same metal due to crystallographic substrate/metal misfit [I]. If the substrate has traces of the depositing metal they will be preferential growth sites. For a smooth deposit a large number of simultaneous nuclei is necessary. However, excessive nucleation density can lead to porous deposits [2]. Surface films of good conductivity are needed for dense nucleation and small nuclei. On cathode blanks the number of active sites increases with increasing surface film conductivity [3-5] and/or surface film porosity [6]. On AISI 3 I6 L stainless steel a more resistive oxide has been found to limit favourable sites for copper nucleation and more conductive film promoted high-density copper nucleation [7]. Also Urda-Kiel et al. have concluded that thicker oxide layers on AISI 304 stainless steel resulted in lower nucleation [8]. Increase in overpotential or current density activates more and more of the potential nucleation sites and this can be seen as higher number of nuclei [9] or smaller average distance between nuclei [10]."

Jan 1, 2012

By J. D. Miller

Low-level radioactive contaminated soils (10-500 pci/gm) created by defense-related activities at certain superfund sites, such as Nevada Test Site (NTS), is a current environmental concern. Many of these contaminated sites may require appropriate cleanup and restoration, which could cost billions of dollars and put tremendous pressure on our limited financial resources. Therefore, the development of a selective flotation process to separate such radionuclides from contaminated soils should be considered. In this study, both a pure depleted UO2 sample and three synthetic UO2/soil mixtures were used to evaluate surface chemistry features and to examine the possibility for the flotation of fine UO2 particles from selected soils. It was intended that this model system would be a reasonable representation of contaminated soils such as those found at the Nevada Test Site which are reported to be contaminated by PuO2 fallout. The effect of reagent schedule, particle size distribution, and surface charge are discussed with respect to the flotation separation of the UO2/soil mixtures. It was found that both commercial fatty acids and reagent grade sodium oleate are effective collectors for UO2 flotation provided the pH is adjusted to the range of pH 8-9. The bench-scale flotation results successfully demonstrated that froth flotation technology can be used to remove UO2 from such model contaminated soils with appropriate flotation chemistry conditions which depend on the soil characteristics and other pretreatment procedures. In the best case, 90.2% of the UO2 was removed from a UO2/NTS soil mixture (119 ppm UO2) and the soil reduced in UO2 contamination from 119 ppm to 17 ppm in a single stage bench flotation. The impact of clay slimes present in the soil is revealed by the results which show that, for example, for a deslimed soil (28x400 mesh and 100 mg UO2/kg soil) 85¬90% UO2 recovery can be obtained with a reduction in contamination to 4.6 mg U02/kg soil.

Jan 1, 1995

By S. Yuan

Oxygen ion conducting yttria-stabilized zirconia (YSZ) tube was used to remove oxygen from molten Cu at 1373K. Outer surface of the tube was in contact with the melt and the inner surface containing a thin layer of porous Ni-ZrO2 cermet electrode was in contact with a reducing gas. The migration of oxygen species (O2-) from the Cu melt through the YSZ tube is accompanied by an equal and opposite flux of electrons maintaining electroneutrality. Without applying an external EMF, the fluxes are maximized by short circuiting the melt with the cermet electrode. For efficient oxygen removal, the YSZ tube must be thin, contact resistances should be negligible, and the electrodes must be porous and cover the entire electrolyte surface for charge transfer. This refining process is environmentally sound, can use reducing gases such as H2, CH4 and CO without running the risk of increasing H or C content of the melt.

Jan 1, 1993

By Batric Pesic

Reactions of metallic iron were studied in several different aqueous solution systems: water, medium salt solution used for the growth of T ferrooxidans, ferric iron solution and solution containing T ferrooxidans. Each system was studied under abiotic and biotic conditions in the presence of T ferrooxidans and as a function of pH, particle size of iron powder, temperature, ferrous and ferric iron concentrations. It was found that metallic iron reacts with water differently than does with ferric iron in water. Surprisingly, T ferrooxidans were non-functional in the dissolution of metallic iron. Also, the reactions of metallic iron with pure water were indistinguishable from the reactions with water containing medium salts for bacterial growth. The reactions with ferric iron were also independent of medium culture compounds. The mechanisms of metallic iron reactions with ferric ions are different from the mechanisms of metallic iron reactions with water.

Jan 1, 2001

By F. F. Lins

There is a large use of mercury in Brazil by the gold miners in the so called "garimpos" (non registered mining operations), where it is usual to recover the gold contained in the gravity concentrates by amalgamation, which is highly deleterious to environment if not conducted properly. Unfortunately, this is a common practice there. After presenting in brief the modus operandi generally practiced in the garimpos and the environmental problems, this work reviews some of the research conducted in CETEM according to two approaches: (i) replace amalgamation by other processes and (ii) develop technology to treat mercury-contaminated soils and effluents. Conventional processes like froth flotation, to recover gold from gravity concentrates, and centrifuges were considered. Also as alternatives to amalgamation, innovative process like the recovery of gold by coal-oil agglomerates and a technology that is currently under development in our laboratory, called gold-paraffin process, are described in brief, some results presented and their potential use assessed. To reclaim sites already polluted a technology was developed to float mercury selectively from contaminated soils. The potential use of centrifuges to pre-concentrate the mercury is also discussed. The scope for applying the last techniques is to concentrate the pollutants in a small volume of mass which would be suitable for recycling or isolation from the environment. A prospective technology to treat contaminated soils, or mercury concentrates, is the immobilization of mercury by adding inorganics. Concerning the ionic mercury which may be present in effluents, precipitation of the ions and flotation of the precipitates are being studied.

Jan 1, 1994

By Marietta Canty

A paper is presented in which an innovative biological process is described for the treatment of cyanide-, metals-, and nitrate-contaminated mine process water. The technology was tested for its ability to detoxify cyanide and nitrate and immobilize metals in wastewater from agitation cyanide leaching. A pilot-scale demonstration is described in which a pilot plant was constructed to demonstrate the technology on a mine process waste stream at a mine in Nevada. The demonstration was performed Jointly under the Mine Waste Technology Program (MWTP), which is funded by the U.S. Environmental Protection Agency (EPA) and is jointly administered by the U.S. Department of Energy&apos;s (DOE) Western Environmental Technology Office (WETO) and the Superfund Innovative Technology Evaluation (SITE) Demonstration Program under Interagency Agreement Number DW89938513-0 I-0. MSE Technology Applications, Inc. (MSE) located in Butte. Montana, was the contractor responsible for conducting the project, and Pintail Systems, Inc., of Aurora. Colorado, was the technology provider. The pilot-scale unit was field-tested at the Echo Bay McCoy/Cove Mine southwest of Battle Mountain, Nevada. The biotreatment process was considered to be successful in destroying cyanide in the mine process water. The process was also determined to be effective in removing metals. The pH was consistently neutralized, and nitrates were successfully removed from the mine process water. As a result of conducting these pilot-scale tests, the biotreatment process was concluded to be an innovative, cost-effective alternative for the treatment of mining wastewaters.

Jan 1, 1998

By M. Misra

The removal of lead and other heavy metals present in an active US Army small arms firing range soil was evaluated in a pilot scale test program at Ft. Polk, Louisiana. Two different acid based extraction processes in conjunction with conventional physical separation methods were used. Physical separation processes consisting of screening and gravity operations removed most of the coarse lead particulates and slugs. Hydrochloric acid leaching followed by precipitation of lead as hydroxide recycled clean soil containing less than 500 mg/L. total lead and less than 5 mg/L TCLP lead. Lead extraction efficiency with hydrochloric acid was 96 percent. The results of lead removal by physical separation in conjunction with acetic acid leaching were not consistent over the whole test period and the total soil processed.

Jan 1, 1998

By Ramana G. Reddy

Thermodynamic modeling and experimental study on impurity capacities and their distribution between mattes or metal and slags in smelting, converting and refining of non-ferrous metals was discussed. A brief review on the recent developments in copper smelting and converting is presented. The analysis showed that, copper smelting capacity increased by a factor of 10 since 60&apos;s, smelting rate increased by a factor of more than 5 and process fuel equivalent decreased by a factor of 2. A thermodynamic model for prediction of impurities capacities in slags and their distribution in mattes and slags was developed. The impurities capacities (i.e. sulfur and arsenic) of slags were calculated a priori with no adjustable parameters using the Reddy-Blander model. The capacities predictions were made in a wide range of matte and slag compositions, PSo, and temperatures in conditions pertaining to copper and lead industrial slags. The calculated results for sulfide and arsenate capacities are in good agreement with the available experimental and industrial copper and lead industrial slags data. The sulfide and arsenate capacities in copper slags (fayalite, ferrite and olivine) and lead slags are reviewed. The application of RB model predicted ratios of O2 and S2 partial pressures in industrial copper smelting processes are discussed. Application of this model for the prediction of Sb, Bi and other impurity capacities and their distribution ratios in mattes or metal and slags, in industrial smelting and refining processes is discussed.

Jan 1, 2003

By K. Osseo-Asare

"The molecular structural and solution chemical characteristics that underlie the surface activity of solvent extraction reagents are highlighted, with particular emphasis on the tendency towards reverse micelle and microemulsion formation. The physicochemical factors that lead to microemulsion-enhanced solvent extraction with chelating extractants are elucidated. Membrane-based contactor systems are described which are uniquely suited for enhanced solvent extraction with microemulsions. The possibility of combining solvent extraction with microemulsion-mediated materials synthesis is discussed. IntroductionThe discovery of new selective extractants has resulted in major breakthroughs which have helped to establish solvent extraction as a versatile separation technology (1-3). A complementary strategy towards new process development is to seek new ways of using the available reagents. This paper explores this second approach. From a molecular structural standpoint, an extractant may be viewed in terms of two components: a polar functional group and a hydrocarbon radical. In the conventional view of solvent extraction, this molecular structure serves two main purposes: The polar functional group provides the binding sites for complexation of metal ions, while the organic group is needed to render the resulting metal-extractant complex organic-soluble. But are these the only properties of the organic and the polar groups that are relevant to the solvent extraction process?In this paper, attention is directed to the fact that solvent extraction reagents possess the molecular structures of amphiphiIes; that is, they are characterized by the presence of spatially separated hydrophilic and hydrophobic groups on the same molecule. A case is made for the view that this amphiphilicity offers interesting opportunities to develop new separation processes which collectively may be described as enhanced solvent extraction (4-6)."

Jan 1, 1996

By N. L. Piret

Reprocessing of low zinc-bearing residuals with a zinc content of less than 10%, originating from the iron and steel industry, has been given more and more attention in the last few years, due to the potential landfill liability and the increasing cost of disposal by dumping. Whereas, recycling of hazardous electric arc furnace dust is already being performed commercially on a large scale in the U.S., Japan and Western Europe, almost no reprocessing takes place in the case of these low grade zinc-bearing materials. In blast furnaces and basic oxygen furnaces dusts and / or sludges are generated at a rate of 1 to 2 % of the respective production. The technologies for the retreatment of these types of materials, either commercially available or still being developed are briefly described hereafter. They involve internal recycling, upgrading by physical separation methods, separate hydrometallurgical processing and pyrometallurgical treatment. Their scope and limitations are critically assessed in terms of technological applicability, economic feasibility and environmental compatibility. Since, the possibtlity of achieving economic profitability is unlikely with this type of material, the main criteria for acceptability of the treatment process are: generation of a iron-rich material, suitable for treatment by the iron/steel industry, acceptance of the non--ferrous metal-bearing sub-product by zinc smelters, generation of non-hazardous waste materials.

Jan 1, 1992

By Marc Liebman

We present the results of a telephone survey of electric arc furnace (EAF) steel producers. This report characterizes the current status of EAF dust generation, treatment and disposal. It indicates the quantity generated, zinc content, other relevant constituents, and plans and trends that will impact on the quantity and characteristics of the dust generated. The survey covers EAF based steel producers in the United States and Canada. It identifies the processors currently employed, opinions about the use of these processors and services, as well as new technologies being considered.

Jan 1, 2000

By Ken-ichi Machida

"Surface modification of R-Fe-N intermetallic compounds was made to improve their magnetic property and nitrogenabsorbing ability, arid high-performance resin-bonded magnets and nitrogen storage materials were developed: Surface coating for Sm2Fe11Nx by the zinc metal produced via photodecomposition of Zn(C2Hs)2 was effective to avoid the further oxidation in the molding process of the fine powders for bonded magnets and the resulting (BH)max values were improved to -186 kJm-3. Meanwhile, R2Fe17 as the mother compounds for RzFe11Nx was highly active for decomposition of NH3 molecule and subsequent nitrogen absorption as metal nitrides. Furthermore, even inert Nz molecule was dissociated on them by impregnating Ru metal and the resulting nitrogen atoms were absorbed in the crystal lattice of R2Fe17. These results demonstrated that the nitrogen storage system was established by cycling the nitrogenation and hydrogenation of RzFe11/R2Fe11Nx materials.IntroductionProcessing for rare earth metals and intermetallic compounds requires well-controlled conditions in order to avoid the oxygen contamination involved in it due to their high reactivity, as causes the serious damage for materials such as magnets, metal hydride for hydrogen storage, and so on. Rare earth-iron intermetallic compounds, R2Fe17, provide the corresponding metal nitrides (R2Fe11Nx) by heating in N2 or a mixed gas stream ofNH3-H2 [l] and, among them, Sm2Fe11N3 has been particularly noted as one of the promising materials for high-performance permanent magnets such as bonded ones [2- 6]. Usually, the nitrogenation for Sm2Fe17 is made in Nz, but it needs the much more hard conditions of reaction pressure (-10 MPa), temperature (-550°C) and time (-72 h) than the nitrogenation in the NH3-H2 mixture [l]. In the latter case, a significant amount of nitrogen can be interstitial introduced in· the R2Fe17 crystal lattice (x=-7) under the more moderate conditions than in N2 (at 0.1 MPa and -450°C for -3 h) [3-6] and then, in a similar manner as metal hydride systems [7], the excess nitrogen in RzFe1 7Nx (x>3) is reversibly desorbed by heating at a temperature around 500°C in Ar to form the RzFe11N3 compounds. This behavior of nitrogen absorption and desorption has a close relation to the sites for nitrogen in the crystal lattices."

Jan 1, 2000

By Shenghui Guo, Ying Lei, Wei Li, Jinhui Peng, Libo Zhang, Yu Li

"In this work, the Panzhihua low grade ilmenite and graphite were milled for 1, 2, 4 and 8 h firstly, then the temperature rising behavior of milled sample in microwave field were studied. The average heating rate of samples milled for 1, 2, 4, 8 h were 1.86, 4.08, 2.82, and 2.32 K/s; Before optimize the microwave reduction process, several experiments were conducted in order to confirm the parameters range. After milled for 4 or 8 h and reduced above 930 oC, the Fe metallization are higher than 90%; Then the optimization was investigated by using response surface methodology (RSM), the significance of predict model and each terms were analyzed, and the optimization parameters were given as: milling time is 4 h; reduction temperature is 1001 or 1070oC; the holding time is 37.5 or 26.9 min. Under these conditions, the Fe metallization given by predict model is 91 or 92 %.IntroductionThere is about 9.66 billion tons of Vanadic Titan-magnetite deposits in Panzhihua, China. In this reserve, there is about 8.73×108 t of TiO2, accounting for 90.54% of the Chinese reserves, and 35.17% of the international reserves and ranking first in the world. [1] Titanium mineral deposits are classified into Rock type and Placer type. Rock type is the igneous mineral, which have high content of FeO (Relative to Fe2O3) and gangue. The Panzhihua ilmenite is a typical rock type ilmenite ore. The higher contents of MgO, CaO, SiO2 and the complex mineralogy are making its direct reduction progressively more difficult."

Jan 1, 2011

By Kotaro Ogura

"Ethylene has been produced in aqueous solution from CO2 by the electrochemical reduction driven by a natural energy. This process is useful for storing a large amount of the natural energy. In the closed system, the conversion efficiency of CO2 is almost 100%, and the maximum selectivity for the formation of ethylene is more than 70%. On the other hand, the current efficiency for the competitive reduction of water is less than 10%. The electrolysis is practicable under such special conditions as three-phase interface consisting of gas, solution and metal, concentrated solution of potassium halide, low pH and copper or copper halide-confined metal electrode. These requirements are thoroughly examined, and the grounds to reply upon are revealed. A series of chemical apparatuses including an electrolytic cell in a large scale are designed for the ethylene production, which allow us continuously to supply raw CO2 and to extract the product.IntroductionIn connection with the depletion of the petroleum reserve, much attention has been paid to the utilization of natural energies such as sunlight, wind force and waves. However, these energies are always changeable, and some means of storing them are necessary for the common use. In general, natural energies are transformed to the electric energy at the time of utilization, but the electricity is not very storable. This is one of the reasons why the application of natural energy is not so expanded. On the other hand, the storing of natural energy by plants is very skilful. In the photosynthesis, solar energy is transformed to chemical energy by fixing carbon dioxide."

Jan 1, 2009

By J. Wong

We report a successful use of x-ray absorption spectroscopy to probe the chemical and structural environment of trace elements in coal. When applied to vanadium in coal, it was found that vanadium exists in at least two environments: a trivalent site 6-fold coordinated by oxygens at ca. 2.0~ and a tetravalent site 5-or 6-fold coordinated also by oxygens, one of which forms a short V=O bond at ca. 1.6a. No evidence of nitrogen (porphyrin)1&apos;or sulfide environment was found. It was also found that the vanadium environ-ments in the raw coal did not survive unchanged in a liquefaction process. These findings have implications for coal cleaning processes and for trace element release into liquefaction process streams.

Jan 1, 1982

By T. J. White

Each year, thousands of tons of toxic concentrates are produced as the unwanted byproducts of industrial operations and smelting activities. The fate of these materials remains open, as in general their consumption is limited and potential markets contracting. Xtaltite (pronounced crystal-tight) is a Synthetic Mineral Immobilization Technology (SMITE) optimized for the concentration, detoxification and consolidation of toxic metal wastes. In this approach, we seek to mimic nature to produce durable synthetic minerals that survive for aeons in well characterized geological settings. This approach has high public acceptability because the concept is easily understood by the layperson and the long term stability of the waste form may be predicted with confidence. In addition, where Xtaltite is used for mine backfill, a system of ecologically sustainable mining development is established. This paper details the design and fabrication of Xtaltite under oxidizing and reducing conditions. To illustrate and contrast these stabilization regimes, specific reference will be made to the treatment of thallium, chrom~um and arsenic wastes. Waste form performance under TCLP, dynamic boiling water tests and in other leaching media will be compared and discussed with respect to their relevance to different disposal options.

Jan 1, 1995