Search Documents

By Mototsugu Matsuno

A new process has been developed to treat fly ash generated from municipal incinerators, which contains not only toxic metals such as lead and cadmium, but also dioxins. The process includes the following steps; fly ash is formed into green pellets with some additives and the pellets are then roasted to eliminate or stabilize the toxic metals and to decompose dioxins. A pilot plant with a capacity of approximately 100 kg/hr was used to test the process. The tests verified that heavy metals were either volatilized or stabilized and dioxins were decomposed by high-temperature roasting. The pelletized ash was found to be non-toxic, so that it can be recycled as artificial lightweight aggregate. It was also found that volatilized metals collected as secondary ash can be recycled as smelting resources.

Jan 1, 2003

By Michael S. Moats, Scott C. Campin, J. Brent Hiskey

"Electrochemical techniques are a valuable means of analyzing the passivation of commercial copper anodes. Electrochemical impedance spectroscopy (EIS) provides information concerning transport and reaction phenomena occurring at an electrode surface. Commercial. copper anodes of varying compositions have been examined using EIS. Experiments were conducted in a flat cell with an electrolyte of 40 gil Cu2 + and 160 gil H2S04 maintained at 65 DC. Impedance spectra were obtained at the potentials characteristic of the open circuit voltage and passive region for each anode. The spectra of the passivating films exhibited a flattened resistive/capacitive loop at middle to high frequencies and an inductive loop at low frequencies. An equivalent· circuit utilizing an inductor-resistor series in parallel with the double layer capacitance and charge transfer resistance was adequate in modeling the impedance data. The influence of anodes impurities on the components of the equivalent circuit is discussed and correlated with a hi-layer passivation model.IntroductionPassivation of copper anodes during industrial electrorefining has received considerable attention in the past few decades. Great strides have been made in understanding the roles of anode impurities [1-25], electrolysis parameters [20,26], and electrolyte chemistries [20,26]. Even so, passivation still occurs even in the most modem of refineries. The exact cause of passivation is not fully understood. It is known that the anode surface becomes covered by a passivating film. This film has been proposed to be CuS04'&5H20, Cu20, or mixed oxides. The localized concentrations of Ft, Cu+, and Cu2+ ions determines which phase is more favorable. The presence of these ions is controlled by the reaction kinetics and diffusion of species through the slimes layer.Reaction kinetics between Cu, Cu +, and Cu2+ are based on the dissolution mechanism of copper. There exists four different models to describe the dissolution of pure copper. The classical model of Mattsson and Bockris [27] involves two single electron transfers with the cuprous-cupric reaction being the rate detennining step. More recently, Wong, Collier, and MacFarlane [28] used ac impedance to elucidate a more complex mechanism involving the affect of pH and anions. Their findings indicate that the formation of cuprous ions in solution, Cu(I)so~ is favored over Cu(1I) ions adsorbed to the electrode surface in the presence of sulfate and as pH increases from pH 1 to pH 5."

Jan 1, 1997

By N. Kanari

Chalcopyrite concentrates and their pure constituents were chlorinated by C12+N2 between 25 °C and 750 °C. The reaction products were analyzed by SEM, XRD and chemical analysis. The effect of gas flow rate and chlorine content of the gas mixture on the reaction rate were investigated. At room temperature, these solids start to react with chlorine giving metal and sulfur chlorides. Complete reaction is achieved at about 300 °C and the iron and sulfur chlorides were fully volatilized. The chlorination residue is composed of valuable metals' chlorides. A simplified flow - sheet for the treatment of chalcopyrite concentrates by chlorine was suggested.

Jan 1, 1998

By Fan Jiang, Haigang Wang, Shi Liu

"This paper describes several applications of Electrical Capacitance Tomography (ECT) in gassolid two phase flows. A new image reconstruction algorithm was evaluated by both simulation and experiments. It is then applied to the online measurement of solids distributions in square circulating fluidized beds (CFBs) and good results were obtained. From the measurement of solids distributions in the bottom zone of a CFB, a bubbly fluidization pattern is identified. A cross-correlation technique was combined with the solids concentration measurements to obtain the flow rate through the dip leg of the cyclone, i.e. the circulating rate of a test CFB. The same· technique was applied in a dense phase pneumatic transport pipe provides the solids concentration, and the flow rate of a wavy gas-solids flow.IntroductionElectrical capacitance tomography (ECT) has been developed for imaging multiphase distributions in the 90's of the ·last century. It is a non-intrusive method. The principle of ECT can be firefly described as follows:Firstly ECT uses a number of electrodes to surround the measuring zone, depicted by Fig. I. The capacitances between the electrodes are measured in turn and an array C is obtained that contains a total number of m independently measured capacitances. Meanwhile the measuring zone is virtually divided into a grid of n pixels, represented by an array G, named the image vector, the gray level of each pixel represents the local value of the concentration of the material. As the material distribution will be reflected by the capacitances between each pair of electrodes, such distributions can be reconstructed according to the measured capacitance, a process called image reconstruction. A common image reconstruction method is called linear-backprojection (LBP). It linearize the relationship between the dielectric distributions in the measuring zone and the capacitances between the electrodes as the following:"

Jan 1, 2004

By Maija-Leena Metsiirinta

The behaviour of copper and lead in zinc roasting has been studied in laboratory scale roasting experiments as well as in large scale trials in an industrial fluidized bed, with the background of Outokumpu Kokkola Zinc smelter. Commercial zinc concentrates with a low and high ( up to 3 wt % ) copper content and with a low and high ( up to 3.5 wt % ) lead content were oxidized to various desulphurisation degrees in the fluidized bed to establish the reaction mechanisms and the paths for copper and lead oxidation in the roasting. Influences of the agglomerate size on the roasting kinetics and micro- scale phenomena were also determined. Optical microscopy was used on the calcine and the findings are presented as numerous photographs of the polished cross sections. SEM/EDS techniques were used for analyzing chemically the phases and particle morphologies present in the samples. Computational thermodynamics was applied to the complex phase equilibria occurring during roasting in the agglomerating calcine. A complete oxidation of zinc concentrate with a high copper and lead content requires a careful control of oxygen coefficient in the roasting in order to maintain a stable operation of the fluidized bed. Oxygen coefficient thus seems to have a significant impact on the hydrodynamic stability of the fluidized bed with fine raw materials.

Jan 1, 2003

By Alvear G. R. F. Flores

It is now 35 years since the organization of the first sulfide smelting conference in 1983. Since then, the smelting base metals industry has experienced several changes driven by the necessity to improve economic, operational and environmental performances and resource efficiency and meet the increasing market demand for metals. In this continuously challenging environment, it is relevant to recognize which are the main challenges that the industry will face in the coming years and critically address our preparedness to respond to them. This analysis have to consider not only the effort required from the fundamental research and technology aspects but also how these pillars interact with the drivers behind the base metals industry. This paper discusses some relevant aspects required to continue developing the base metal industry focusing on copper. Aspects such as the need to supporting the generation of fundamental metallurgical knowledge, acquisition and proper use of data with advanced analytics methods, technological innovation to develop sustainable process flowsheet are discussed with emphasis on efforts conducted by Aurubis.

By Torma A. E.

Biotechnological processes are considered to be cost effective especially for situations where the recovery of metals from 'Very large volumes containing trace metal concentrations (less than 10 ppm) is concerned. Microorganisms, alive or dead, or their products can be highly efficient and selective biosorbents for metal concentration. It is important that the metal bound to the biosorbent can be stripped by suitable agent(s) and regenerated for repeated use. The stripped solution should be concentrated enough to be introduced into the common metal recovery circuit. The industrial acceptance of biosorption processes is dictated by increased competitive advantage over other processes. This paper reviews the pertinent literature?, regroups the information, and points out future possibilities for the mineral and metal processing industries.

Jan 1, 1992

By Maija-Leena Metsärinta

The behaviour of copper and lead in zinc roasting has been studied in laboratory scale roasting experiments as well as in large scale trials in an industrial fluidized bed, with the background of Outokumpu Kokkola Zinc smelter. Commercial zinc concentrates with a low and high ( up to 3 wt % ) copper content and with a low and high (up to 3.5 wt % ) lead content were oxidized to various desulphurisation degrees in the fluidized bed to establish the reaction mechanisms and the paths for copper and lead oxidation in the roasting. Influences of the agglomerate size on the roasting kinetics and micro-scale phenomena were also determined. Optical microscopy was used on the calcine and the findings are presented as numerous photographs of the polished cross sections. SEMIEDS techniques were used for analyzing chemically the phases and particle morphologies present in the samples. Computational thermodynamics was applied to the complex phase equilibria occurring during roasting in the agglomerating calcine. A complete oxidation of zinc concentrate with a high copper and lead content requires a careful control of oxygen coefficient in the roasting in order to maintain a stable operation of the fluidized bed. Oxygen coefficient thus seems to have a significant impact on the hydrodynamic stability of the fluidized bed with fine raw materials.

Jan 1, 2003

By Ben Hogg

Since the development of the top-submerged lance (TSL) technology for copper and lead smelting by the cooperation of Mount Isa Mines (MIM), now owned by Glencore, and the Commonwealth Scientific Industrial Research Organisation (CSIRO) the core of the ISASMELT™technology has always resided in the lance system. Through continuous innovation and operation of our own smelters, first at MIM, subsequently at Mopani, and also at both the Kazzinc Copper and Kazzinc Lead smelters, Glencore Technology have expanded the core equipment supply to enhance the plant operability. The success of Glencore Technology’s expertise can be directly measured by the success of the Kansanshi Copper Smelter plant, which achieved 100% nameplate capacity within three months of start-up. This paper describes the ISASMELT™ core equipment and how it is applied to smelt sulfide materials. It highlights the strength of the ISASMELT™: continuous innovation to facilitate the versatility and continued increased capacity with every plant implementation.

By V. I. Lakshmanan

Crown ethers are gaining importance in separation technology specifically for rare earth elements (REE, La to Lu plus Y) and precious metals (Au, Ag, Pt, Pd, Rh and Ir) due to their specific binding ability, metal complex stability and high extraction efficiency. The selectivity of crown ethers in extraction of these metals depends on different factors, including the cavity diameter and nature of a donor atom of the crown ether, size and charge of the metal ion, diluents and counter ion. Demand for strategic REE and precious metals are consistently increasing in the world while the separation of these metals is most challenging tasks. In this paper, the use of crown ethers in separation of REE and precious metals, reaction mechanisms and simplified process flowsheets will be elucidated. New reagents with high selectivity for the separation of these metals are further expected to produce high purity metals.

By H. Bai, B. G. Thomas

"A three-dimensional finite difference model has been developed to study the liquid steel-argon bubble two-phase turbulent flow in continuous casting tundish nozzles. Experiments have been performed on a 0.4-scale water model to verify the computational model by comparing its prediction with velocity measurements using PIV (Particle Image Velocimetry) technology. The computational model was developed using CFX and then employed to investigate the effects of various casting process variables. A fast, simple inverse model to quantify relationships between those process variables was developed, based on interpolation of the numerical model results, using Bernoulli's Equation and advanced multivariable curve fitting methods. Predictions using this model compare well with plant measurements. The model has been applied to present trends and observations on the relationship between casting speed, tundish depth, slide gate opening, and argon gas injection rate. The results can also be used to predict .the theoretical steel flow rate through the nozzle, so that clogging conditions can be identified in the plant.IntroductionTundish nozzle geometry is one of the few variables that are both very influential on the casting process and relatively inexpensive to change. Designing an effective nozzle requires quantitative knowledge of the relationship between nozzle geometry and other process variables on the influential characteristics of the flow exiting the nozzle. This relationship depends on the flow pattern within the nozzle components. Most previous modeling studies of flow in the nozzle have focused on single-phase flow [1-4]. Argon injection into nozzle is an efficient and widely employed method to reduce nozzle clogging, even though the real working mechanism(s) are still not fully understood [5]. Argon injection may greatly affect the flow pattern in the nozzle, and subsequently in the mold. Therefore, two-phase flow modeling is needed to improve understanding of fluid flow in the nozzle."

Jan 1, 2000

By M. Wallin

Millions of tons of sludge from different metallurgical processes are produced worldwide annually, and the environmental impact of landfilling these often hazardous sludges stresses the need to understand their role as valuable resources. The current work explores the potential of producing a saleable low-phosphorous ferromanganese alloy by utilizing sludge from the silicomanganese industry together with an iron source. The aim of the project is to explore the feasibility and practical challenges related to reduction and dissolution of manganese and silicon from the sludge to liquid metal and slag. Parameters such as ratio of input material as well as the effect of adding limestone and coke to the mixture were explored by thermodynamic calculations and adapted experimentally. Results show that a ferromanganese alloy, in fact, can be formed, while silicon and calcium forms a complex slag that captures a significant amount of impurities.

By Zhang Libo, Li Wei, Peng Jinhui, Guo Shenghui, L. Jing

Partially stabilized zirconia ceramics (PSZ) were prepared by microwave sintering using natural baddeleyite which was obtained by flotation of baddeleyite ore as starting materials. Because of using natural baddeleyite as raw and the process producing no waste, it realized shorter process, energy savmg, environmentally-friendly and non-damage processing. In this work natural baddeleyite stabilized with 3.8wt.% CaO were sintered at 1300°C for 60min in a multi-mode 2.45GHz microwave furnace. Microwave sintering could fast heating and sintering. Besides that, microwave sintering could heat materials wholly, low the sintering temperature, improve the materials properties and save energy. X-ray spectrum displayed the product composed by the tetragonal phase and monoclinic phase that also showed the product was PSZ. Fine and uniform microstructures were observed in the product through scanning electron microscopy. PSZ which was with high density was confirmed by the method of the Archimedes technique.

Jan 1, 2011

By A. E. M. Warner

In co Limited has long and extensive experience in converting nickel-copper primary smelting mattes over a broad range of nickel/copper weight ratios and combined nickel-copper-cobalt contents. At the Copper Cliff Smelter, the composition of the converter product matte has to meet the requirements of the matte separation process; at the Thompson Smelter, converter matte of a different composition is cast into anodes for nickel electrorefining; and in Soroako, Indonesia, a very low copper product matte is granulated for the Japanese market. Recently, Inco has conducted pilot plant testing of three possible nickel-copper matte continuous converting routes, namely flash converting, oxygen top blowing-nitrogen bottom stirring, and tuyere blowing. This test work has generated substantial new information on nickel-copper matte converting chemistry. This overview paper reviews the metallurgy of nickel-copper matte converting, in particular the behaviour of cobalt and the operating conditions required to meet the iron and sulfur specifications of the product matte. The relevant thermodynamic information is used to discuss the industrial data.

Jan 1, 2003

By Yoichi Takeda

The CaO-FeOx-Cu20 slag has been practically applied to continuous converting of copper, and also has potential for refining of copper. Liquidus lines of the slag system and phase stability diagram for the liquid slag and the existing solid compounds under copper saturation are presented. Liquidus composition was determined by chemical analysis of slag sample saturated primary solid. The temperatures of invariant equilibria were investigated by thermal analyses. Oxygen potentials on the liquidus lines, the univariant and invariant equilibria were estimated from the relation slag composition and oxygen potential that relation was confirmed in separate experiments.

Jan 1, 2003

By C. Ek

In bismuth metallurgy, low-copper high-sodium mattes are by-produced. Different charges containing mixtures- of crude mattes, oxidized matte, and/or copper sulfide concentrate and/or copper silicate ore have been smelted to give a rich matte and a disposable slag, then converted to obtain blister copper with high recovery and a rich slag to be recycled.

Jan 1, 1983

By Lloyd R. Nelson

The feasibility of producing low carbon (LC) ferromanganese (FeMn) by lime-'ore' melt refining of high-grade ferromanganese silicon (FeMnSi) was investigated. Thermodynamic simulations demonstrated significant benefits in moving from a single-stage ladle operation to a two-stage counter-current reladling operation (to emulate the commercial Penin Process). The theoretical alloy silicon content was predicted to be refined from 1.57 to 0.005 per cent silicon, at a 6.2 per cent higher manganese yield (yield predicted to increase from 82.3 to 88.5 per cent). Extension of this counter-current refining principle, to a multistage Counter-Current Reaction Launder (CCRL) was investigated using the Slag Metal And Gas Klnetics (SMAK) software to model the mass transfer kinetics of the multicomponent coupled reaction system. Simulation results suggested that commercial production of 50 000 tonnes per annum (tpa) of refined LC FeMn, containing less than 0.5 per cent silicon, at manganese yields of up to 90 per cent, should be feasible in a compact CCRL (7 m long by 0.7 m wide).

Jan 1, 1994

By Ayşe Ece Yıldızçelik, Mehmet Buğdaycı, Onuralp Yücel

ZrB2 and TiB2 are significant metal borides. They are being used in various industrial areas from space technology to nuclear industry owing to their physical properties such as high melting point, high thermal/electrical conductivity and low density. Present study was conducted in two main stages: self-propagating high-temperature synthesis (SHS) reactions and leaching. ZrO2, TiO2, B2O3 were used as starting material and Mg was used as a reductant to produce ZrB2-TiB2 powders via SHS. Therefore, it was aimed to determine production parameters, leaching conditions and comprehensive examination of final product features. The samples were characterized by using chemical analysis (AAS), XRD, XRF and SEM/EDS techniques.

Jan 1, 2015

By I. Peerawattuk

Growing demand for Li-based battery technologies is leading to an unprecedented growth in the lithium industry. Although innovation in battery technologies has pushed lithium into the spotlight, lithium was not always known for its application in batteries. The primary use of lithium—prior to the introduction of commercial lithium-ion batteries in the early 2000s—was in the ceramics, glass, grease, and the medical industry. Before being converted into usable forms, lithium products must be upgraded from the raw material. Processes for recovering lithium may involve: thermal treatment, water leaching, solar evaporation, ion exchange, carbonation, and electrodialysis. Presented, is a historical review of lithium applications and the different techniques of converting lithium-rich minerals and brines into usable products with additional discussion on future lithium extraction processes.

By Fumito Tanaka

The Mitsubishi process is the sole pyrometallurgical process for the continuous production of blister copper from copper concentrates and has been successfully operated around the world. The development of calcium ferrite slag (CaO-FeOx-Cu20), the so-called "C-slag", has enabled continuous converting from matte to blister copper in the commercial scale operations. Commercial interests in the slag led to many papers over the CaO-FeOx slag. However, CU2O- bearing slag has not been studied well due to experimental difficulties. The authors have quantified the thermodynamic properties ofthe CaO-FeOx-Cu2O system. The results have been utilized to analyze various issues related to the converting furnace, such as the magnetite precipitation from the slag or from blister copper and to develop better controlling criteria for the continuous converting operation.

Jan 1, 2003