Search Documents

By L. H. Lewis

The relationships that link microstructural properties of advanced permanent magnet materials with magnetic properties such as the coercivity are often difficult to quantify, especially in materials with nano-scale structures. Recent work on RE2Fe14B-based powders fabricated with rapid- solidification techniques such as inert gas atomization (IGA) and melt-spinning provide insight into the nanostructural features which affect the acquisition and stability of coercivity. In all cases the coercivity is found to be a function of both the scale of the constituent microstructure and of the presence and distribution of minor phases.

Jan 1, 1997

By Manuel Zamalloa

The outstanding metallurgical performance of the Noranda continuous converter (NCv) in operation since November 1997 has allowed the company to meet production and environmental targets. This achievement positions this new technology as a strong alternative continuous converting technology for copper production. Knowledge of slag chemistry has been important in this respect. The purpose of this paper is to discuss the effect of key parameters including temperature, oxygen potential, slag composition and levels of copper oxide in slag on the conditions leading to magnetite precipitation, as well as on the conditions affecting the liquidus ranges of NCv slag. The above variables are evaluated using industrial data and thermodynamic predictions. Practical implications of customizing operational fluxing procedures to determine optimum operating windows are also discussed.

Jan 1, 1999

By D. J. Donaldson

The PAL process for recovering nickel from laterite ore requires large volumes of thick abrasive slurry to be raised lo high temperature (245°C+) and pressure (40 atm.+). Flow diagrams of the process typically result in facilities that have serious operating and reliability problems. Most of the problems can be attributed to using multiple pump stations to raise the slurry to autoclave pressure, large amounts of flash and live injection steam to heat the slurry to autoclave temperature and several steps of flash cooling to lower the temperature and pressure of the abrasive autoclave slurry down to atmospheric conditions. It is proposed that operating and reliability problems of PAL facilities can be mitigated by using Tube-in-tube heat exchangers and "float type" positive displacement pumps. The subject paper describes an innovative application of such equipment in the facility design of the PAL process. Keywords: Nickel, Laterite, PAL, Heating, Slurry

Jan 1, 2004

By Chen Yongming

In order to eliminate the serious environmental pollution caused by low concentration of sulfur dioxide smoke in antimony smelters, a new smelting process, named as reducing-matting smelting, is proposed in this paper. The effects of technical conditions such as smelting temperature, smelting time, Pyrite cinder addition and the amount of additive on the smelting of stibnite concentrate have been investigated by the method of single-factor experiment. The results show that the optimum conditions are as follow: The amount of pyrite cinder is 1.2 times of its theoretical amount. The addition of soda and sodium sulfate is 15% and 72.6%, respectively, to the amount of stibnite concentrate when the total amount of sodium is 30%. The reducing-matting smelting is conducted at 1100°C for 2h then the smelting temperature is raised to 1200°C for 50min. Under the optimum conditions, the direct and total recovery ratio of antimony can gain 90.99% and 98.87%, respectively, and the fixed ratio of sulfur is higher than 99%.

Jan 1, 2006

Off-gas cleaning from metallurgical plants requires? in many cases very low dust contents which are difficult to achieve with conventional scrubbers, even with high energy input. Lur.gi has developed a scrubber which improves the separation of the fine dust by electrical charge prior to. the scrubbing zone. An Electrostatic Scrubber has been successfully installed for the off-gas cleaning from slag' granulation after a waelzkiln achieving less than 1 mg/m3 in the clean gas.

Jan 1, 1992

By Naoki Hiroyoshi

It is generally accepted that ferric ions are effective for leaching chalcopyrite as an oxidant and ferrous ions contribute to the leaching only as a source of the oxidant ferric ions. However, this paper shows that ferrous ions are more useful for leaching chalcopyrite than oxidant ferric ions in sulfuric acid solutions in air at ambient temperatures. Leaching experiments and dissolved oxygen consumption measurements were carried out with a very pure chalcopyrite and 0.001 - 1 mol dm-3 sulfuric acid solutions containing 0 - 0.1 mol dm-3 ferric or ferrous ions at 303 K. Chalcopyrite oxidation with dissolved oxygen was promoted by ferrous ions but suppressed by ferric ions. As a result, the amount of extracted copper was larger with ferrous ions than with ferric ions. Effects of Thiobacillus ferrooxidans on the ferrous promoted chalcopyrite leaching were also investigated and discussed based on the experimental data.

Jan 1, 1999

By P. M. Pincheira Brown

The widely accepted inverse relationship between copper prices ail stocks, has been commonly used by analysts to explain the behavior of the copper market and to forecast film copper pries. However, empirical data have not shown such a clear relationship between copper prices and stacks. Existing evidence only indicates a weak tong-nut relationship that vanishes in some periods. In this paper a simple comprehensive model is provided which explains both parallel and opposite direction movements between prices and stocks. Former are explained mainly by stocks demand expansions-contractions while the latter are in essence due to increases in the supply curve. Furthermore, econometric estimations are provided, thus giving a powerful tool to forecast and explain price developments of the copper market.

Jan 1, 1999

By Y. W. Miao

Along the south-west coast of Taiwan is about 550,000 metric tons of heavy sand deposit containing about 10 % black monazite. The Institute has developed a separation process to recover the individual rare earths and the developed process has been commercialized by a local private company. The decomposition of the local black monazite by sodium hydroxide through hydrothermal and fusion methods has been investigated. In the hydrothermal process 4.5 wt. % of aqueous alkali solution was used in an autoclave. In the fusion process, caustic soda (9.8% NaOH) was employed in am open cylindrical reactor. The same product of hydrous rare earth oxides were obtained and then dissolved by hydrochloric acid and the p-H adjusted in order to separate the thorium from the rare earths. After filtration, the filtrate contained rare earth chloride and the cake contained mainly the silica and thorium hydroxide. Both methods give a yield of 90 % with respect to the rare earths recovery. A detailed description of operation and comparison of the two methods are given.

Jan 1, 1989

By Kevin L. Purdy

The Process Technology Center of Phelps Dodge Mining Company (PDMC) .operates several test facilities in support of PDMC's hydrometallurgical operations. Installations for small leach columns, 15 cm. to 60 cm. (6 in. to 24 in.) in diameter, and large leach columns, 1.8 m. (6 ft.) in diameter, are complemented by a test facility for SX/EW operations. The history of and reasons for the development of these facilities: are described and original standard equipment is discussed. A primary goal in constructing these facilities was achieving a high degree of flexibility to allow for testing of new equipment and new leaching and SX/EW technologies as they are developed. Along with this challenge, construction of a filly integrated SX/EW test facility on a small scale brought its own set of challenges.

Jan 1, 1999

By Hector M. Lizama

A new technology, known as the HydroZinc? process, is described for the recovery of zinc from sulphide ores that includes heap leaching, neutralization, solvent extraction and electrowinning. Unit operations were scaled up from bench-scale to a 1-t/d zinc cathode demonstration plant. Bench-scale studies defined the process chemistry and a process flowsheet. Column tests were used to design full-scale heaps for zinc bioleaching, and mini-pilot equipment was used to design a solvent extraction circuit. The characteristics of the process required development of a bleed circuit for water and impurities. The complete integrated process was tested on a demonstration plant scale for two years, with about 10 000 t of zinc sulphide ore being bioleached in two 6-m-tall test heaps. In addition to 1 t/d of zinc cathode, iron hydroxide and gypsum residues were produced. The process also generated a small effluent bleed. Over the course of the two-year demonstration test, a number of technical hurdles were overcome and several improvements were made. Some of the more significant ones are presented along with process descriptions and experimental and demonstration plant data. Some engineering aspects and economic evaluations of the new process are also discussed.

Jan 1, 2003

By Andreas Nolte

In 1999 HÜTTENWERKE KAYSER AG (HK) in Germany will produce more than 180,000 t/y of electrolytic refined copper. To achieve this production from materials with copper grades from two to seventy percent and diverse copper alloys, HK operates three blast furnaces, one holding furnace two Peirce Smith converters and two anode furnaces. Technical, metallurgical and economic factors for the ongoing process optimization are outlined. The fluctuating quality and quantity of raw materials renders complex this optimization. The principal variables are the quality and quantity of process consumables: coke, copper-iron, limestone, oxygen, as well as the blending of feedstock and a new organization of the operating crews. The search for new metallurgical process parameters is ongoing. HK started with an intensive research programm in November 1997. As a result it will be possible to cut processing costs by about ten per cent, to increase the blast furnace capacity by ten per cent and to lower the metallurgical losses of copper and tin in the slag by more than ten percent. The presentation concludes with information on future steps to continue the optimization process.

Jan 1, 1999

By Liping Li

A comprehensive three-dimensional two-phase mathematical model was developed to represent a channel type reactor with intense bottom gas agitation. Tracer dispersion and particle tracing methods were used to conduct the analysis based on the solution of the Navier-Stokes equations. Different operational parameters, such is gas volume flow rate. bubbler separation aspect ratios and liquid Input flow rates, were investigated for the purpose of reactor optimization. The numerical calculations were compared with experimental results obtained at the University of Missouri and a good general agreement was observed. Relatively low longitudinal mixing was observed characterizing the system as a "plug-flow" type reactor, in contrast to the intense vertical mixing, under the conditions investigated. Some general mixing characteristics are also discussed In connection to the behavior of other metallurgical reactors.

Jan 1, 1996

By P. K. Narasimhargahavan

This paper discusses briefly the major reasons associated with the growth and its impact on the energy requirement and Environmental imbalance. A projection based on the present global Alumina and Al requirement indicate a substantial further growth of at least 30% over the next 10 years. It is indicated that the main factors which are likely to influence investments are the environmental factors such as the Climate Change and global response to the growing energy prices and sustainable development. Each of the developed / developing nations must find response to the GHG emissions which will encourage the Al Industry to make an effective contribution to global warming while preserving the international competitiveness of the industry - a challenging task. The efforts shall concentrate on improving energy efficiency in the industry possibly of the order of 25% over the next 10 to 20 years. The developments in this line are discussed.

Jan 1, 2010

By Kenshi Kawabata, Mitsuji Ueda, Junko Umeda, Katsuyoshi Kondoh, Kantarou Kaneko

Solid-state recycling process of in-house scraps of machined magnesium (Mg) alloy wastes has been established to directly produce wrought materials via the repetitively plastic deformation by Roll-compaction (RCP) and the conventional hot extrusion. The coarse chips, wasted in machining AMX602 (Mg-6Al-0.2Mn-2Ca) cast billets used for the gate bar used in Electronic Toll Collection (ETC) of the high-way system, were employed as the input materials in this study. RCP process enabled to serve coarse Mg alloy powder consisting of refined grains and intermetallics with no re-melting. They were easily consolidated by hot extrusion, and their wrought alloys showed both homogeneously refined grains less than 1~2 µm by dynamic recrystallization and randomized texture by repetitive plastic deformation on the input wastes. These materials revealed extremely advanced mechanical properties of high tensile strength of 356MPa and high ductility of 14.8%, compared to the originally virgin materials with 270MPa TS and 5% elongation. When applying the same Mg alloy wastes via RCP process to the mass production in the company, the large-scale extruded materials also indicated the superior tensile properties. It means that this direct solid-state process is held as “Up-grade recycle of metal wastes”.

Jan 1, 2008

By B. J. Beaudry

The preparation of alloys containing one to two percent of the volatile lanthanide metals Sm, Eu, Tm and Yb in the high melting point (HMP) rare earth metals Sc, Y and Lu was accomplished by a vapor deposition, diffusion method without crucible contamination. The method avoids the melting of the HMP metals which would introduce impurities from the crucible, generally Ta or W. Plates of the HMP metals were hung from the lid in the upper part of the Ta crucible. The volatile metals were placed on the bottom and the lid welded in place under an atmosphere of helium. By proper selection of thee alloying temperature, the effusion of the metal vapors, through the helium atmosphere was slow enough to permit diffusion to occur and prevent refluxing of the newly formed alloy. Very volatile metals such as Mg required a Knudsen cell with a suitably sized hole to prevent too rapid transfer of the low melting metal. Electron microprobe analysis of a cross-section of the HMP metals showed a homogeneous distribution of the volatile metals. The time and temperature required to obtain a homogeneous rare earth alloy without contamination are given. The use of a Knudsen cell to form magnesium-rare earth alloys is reviewed.

Jan 1, 1992

By Xi-Shan Li, Qian Li, Yong-bin Yang, Li-na Cui, Tao Jiang, Jie Ge

"With regard to control environment pollution in the roasting pretreatment of sulfur & arsenic-bearing gold concentrate, roasting of double-layered pellet was proposed. In the paper, the characteristics of double-layered pellet roasting were studied. Removal and solidification rates of sulfur and arsenic were investigated as primary factors. The result indicated that the removal and solidification rates of arsenic reached up to 95.91 % and 98.95% while the sulfur was 97.19% and 97.90% respectively on the premise of adopting slaked lime as solidified agent at temperature of 6000, the package proportion of 2.14 and roasting time of 3h. However, pyrite and arsenopyrite were transformed to hematite and magnetite and product of solidification mainly consisted of calcium sulfate, calcium arsenate and calcium sulfite within optimum roasting parameters.IntroductionUtilization of refractory gold resources has been gradually concentrated on with the depletion of the gold resources which are easy to deal with in the world [1]. Sulfur and arsenic-bearing gold ore is a typical refractory gold one, in which ultrafme gold is encapsulated in the structure of metal sulfide minerals [2,3], so it gives poor recovery through direct cyanide leaching. These refractory ores need pretreatment before the process of cyanide leaching to undermine lattice structure of pyrite and arsenopyrite containing gold [4] so that the gold could touch with cyanide solution [5]. Among various methods of pretreatment, conventional roasting method is most effective, but this process generates gases such as S02 and As203 harmful to environment. Therefore solidification roasting was proposed to solve this problem occurring in the conventional roasting at the end of last century."

Jan 1, 2013

By W. Dutton, D. Simms

"The clearing of tuyeres on copper and nickel converters or similar metallurgical, vessels has, for many years, been done using mainly a manually- operated ""puncher"". One such device is the ""Gaspe Puncher"" developed in 1962 at Noranda's Gaspe Smelter. In an attempt to remove the operator from the cab of the Puncher, and to relieve him of a tedious, uncomfortable job, Noranda's Horne Division, in cooperation with Heath & Sherwood (1964) Limited and the Noranda Research Centre, undertook to automate the Gaspe Puncher used on the Noranda Continuous Smelting Process Reactor.The automated puncher is controlled by a Texas Instruments Model 530C Programmable Controller (PLC). Position measurement and control is done using non-contact position measuring equipment from the Tele-Controls Division of Geodimeter Inc. The entire automation system was installed on an existing Gaspe Puncher with minimum disruption to the operation of the smelting process. The operator's panel allows the user to ""block out"" any individual tuyere, and to select any of a variety of operating modes.The development of the automated puncher is described, and the results of several months operation are given.IntroductionThe tuyeres of copper and nickel converters and similar metallurgical vessels become blocked with solidified material formed by the cooling action of the blowing air. This restricts the converting operation. Clearing these blocked tuyeres has for many years been done mainly using a manually-operated ""puncher"" which uses a hydraulic or pneumatically-operated piston to drive a steel bar into the tuyere. The Gaspe Puncher, developed at Noranda's Gaspe Smelter in 1962 is one such device. It is currently being built and sold by Heath & Sherwood (1964) Limited, under license to Noranda. There are over 200 units in operation world-wide.In an attempt to remove the Puncher operator from the cab of the Puncher, and to relieve him of a tedious, uncomfortable job, and to increase productivity, Noranda's Horne Division, in cooperation with Heath & Sherwood (1964) Limited and the Noranda Research Centre, undertook to automate the Gaspe Puncher used on the Noranda Continuous Smelting Process Reactor. This paper describes the development of the automated Gaspe Puncher, its installation at the Horne Smelter, and the results of its operation after several months."

Jan 1, 1989

By Alicia E. Ares, Carlos E. Schvezov

In the present work it was observed the nucleation and growth of grains in the equiaxed zone of metal matrix composites (MMCs) samples directionally solidified wit the presence of columnarto- equiaxed transition (CET) in the samples. In order to do so, first, it was defined the difference between the real temperature at a given instant, which it is used in the analysis, its variation and furthermore, the variation in the solid fraction with time between the beginning and the end of solidification. It was determined a growth law assuming a lineal variation of equiaxed grain radius as a function of time, and also, it was expressed a law of grain density as a function of time, considering the presence of SiC and Al2O3 particles in the matrix. Finally, the results obtained were validated with measured values of grain density at each position of the thermocouples in the equiaxed zone of the solidified samples.

Jan 1, 2015

By Biserka Lucheva, Tzonio Tzonev

"Recycling of aluminum scrap and dross is significant in the economic and energy saving, as well as in the environmental protection. Recovery of metal aluminum depends on many factors. The aim of this work is to investigate experimentally the metal recovery under different conditions. The processing of aluminum dross was carried out in DC electric arc rotary furnace. The optimal technological parameters are determined. It is turned out that the presence of crushing refractory bodies during the processing of the aluminum dross in the rotary furnace increases the degree of aluminum recovery with about 10 %.IntroductionCompact and granular aluminum dross are used for the fulfillment of the experiments, which were obtained by salt free melting of aluminum scrap. The only preliminary preparation of the compact dross is crushing them into proper size, in compliance with the size of the opening for furnace charging and removing of fraction – 1 mm. The granular dross is subjected to sieving also with the purpose to remove the fraction – 1 mm. In these conditions the content of the metal phase in the compact dross is 72 %, and in the granular – 77 %. The processing of aluminum dross was carried out in DC electric arc rotary furnace (Figure 1).The purpose of this research is to investigate experimentally the metal recovery under different conditions and to establish the dominant factors, which need to be controlled."

Jan 1, 2008

By William J. Pardee, Michael A. Shaff

"Deeper materials science knowledge from mathematical models and in situ material property sensors will be exploited in next generation factory process controllers to improve productivity and quality. These intelligent control systems will accelerate productivity growth and materials science application through the ease with which they can be modified to accept new materials knowledge and sensors. Carbonization of resin matrix carbon fiber composites, specifically, is a violent solid state chemical reaction with large stresses due to gas pressure, matrix shrinkage, and differences in thermal expansion. The matrix strength falls sharply, then rises again during the process. At least two competing reaction paths are important; the first cleaves methylene bonds, reduces toughness, density and stiffness; the second reforms those bonds, ultimately resulting in aromatic ring condensation that increases density, strength, and modulus. Since these reactions have different temperature dependencies, one can expect to shift the process towards the second path by changing the heating rate, but that change must be accomplished without producing macroscopic interlaminar crack growth. To accomplish this, we employ gas sensors to infer matrix chemical state and acoustic emission to identify microstructural changes and to recognize brittle fracture. The latter does not prevent delamination, but is important in testing models for the causes of delamination and in improving the processing cycle. This paper describes a control strategy to accelerate the process while still lowering the risk of failure.IntroductionDeeper materials science knowledge from mathematical models and in situ material property sensors will be exploited in next generation factory process controllers to improve productivity and quality. These intelligent control systems will be more easily modified to accept new materials knowledge and sensors, thus accelerating productivity growth. Such a control strategy for carbonization control is described below.Carbon-carbon composites are time consuming and costly to manufacture. Processing methods have been developed empirically and are usually very conservative because the process often fails when any change is made. Apparently minor changes in materials or geometry can produce failures that are difficult to diagnose and correct. We will describe below several essentially unavoidable sources of variability. These are best dealt with by applying materials science to adapt (i.e., closed loop control on materials properties) the process in real time to reduce the effect of unavoidable model idealizations, material variability and environmental noise. The most critical issue in control of the carbonization process control is avoiding catastrophic delamination. The strategy developed below makes use of a priori materials knowledge and real time sensors to accelerate the now very slow process without destroying the material, and without requiring unreasonable resources to determine the statistical properties of the material."

Jan 1, 1988