Search Documents

By W. Kasprzak

Press-fit systems are widely used to seal oil lines in the automotive engine components. In the case studied a ball plug made from the 7075 A1 alloy was inserted into a 319 Al alloy cast component. The oil lines were subjected to the required component service pressure. This paper addresses the analysis of the ball plug/casting hole press-fit performance. The tools used to investigate the plug system included: the SEMIEDS technique for the assessment of the plug and the casting hole wall surface integrity; image analysis methods for the characterization of the ball plug/casting hole interface; matrix microhardness measurements of the plug and casting components; laboratory ball plug insertion, speed and force correlation; as well as the ball shearing mechanism analysis. Laboratory tests indicated that optimization of the aluminum matrix hardness in the 319 A1 alloy cast components resulted in considerable improvement of the press-fit system sealing properties.

Jan 1, 2002

By Michael A. Krstich

A soil washing pilot plant to treat soils at the U.S. Department of Energy (DOE) owned Fernald Environmental Management Project (FEMP), was designed based on extensive bench-scale testing. The system's design incorporated a combination of physical separation and' chemical extraction processes and was tested on two soils. The textural composition of the two soils was approximately 20 percent sand, 60 percent silt, and 20 percent clay. Since this grain size distribution was not considered optimum for physical separation techniques, thesoil washing pilot plant had to be designed with selected equipment to provide specific soil size fractions during processing operations. A trommel, vibrating screen deck, centrifuge, and attrition scrubber were used in the system to selectively separate specific soil size fractions at 4.75, 2, 0.3, and 0.02 millimeters (mm). The trammel used high pressure water [1000 pounds per square inch (psi)] during the initial step of the process to reduce soil aggregates to single grain composition, separate out greater than 4.75 mm gravel, and dislodge chemical contaminants from the individual soil particles. The vibrating double-screen deck provided 2 - 4.75 and 0.3 - 2 mm soil fractions that, when combined, averaged greater than 75 percent solids for both soils. The centrifuge was designed to take the less than 0.3 mm soil slurry from the screen deck and produce a particle size of 0.02 mm. The centrifuge produced a high solids stream that averaged greater than 70 percent solids for both soils. These 0.02 to 0.3 mm soil solids from the centrifuge were combined with the 0.3 to 4.75 mm soil solids from the screen deck and processed through the attrition scrubber. The data collected from the pilot-plant operation was used to aid in the design of a full-scale system and was instrumental in formulating full-scale process operations and the selection of equipment.

Jan 1, 1995

By Pan Gu, Zhen Zhang, Jiang Diao, Bing Xie, Hongyi Li

Furnace refractories are in most cases chemically incompatible with smelter slag, which leads to a steady erosion in their thickness over time. Once too thin, refractory walls become mechanically unstable and catastrophic failure can result. Historically, external shell cooling was applied to generate a freeze lining of slag and thus prevent refractory erosion. Many modern high intensity smelting furnaces instead maintain their physical integrity by the use of internally cooled wall panels, plates or finger coolers. An initial refractory lining is often installed inside of the coolers, such that the furnace originally operates with a temperature (insulated) rather than a heat flux (freeze lined) boundary condition. This paper examines the change in slag-wall heat transfer coefficient and slag superheat as a function of process intensity. The implications of the changes in heat transfer on residual brick thickness are explored using analytical modelling.

Jan 1, 2016

By Kathryn A. Mrotek

The textural growth patterns of nodules from two areas in the North Pacific and the South Pacific are characterized by mottled, columnar and compact-type zones. Amorphous material (mainly iron and manganese hydrox-ides) is a botryoidal-forming phase in the mottled and columnar zones. Crystalline material (platy crystals of birnessite and crystallites of todo-rokite) is found primarily in the mottled zones on botryoidal structures or as long-protruding structures growing onto that portion of the nodule in contact with the underlying sediments. The long-protruding mottled zones contain little or no biogenic debris, suggesting that these zones grew un-interruptedly within the underlying sediments. The coalition of spheroidal knobs comprising some of the nodules also suggests a relatively long residing time within the sediments. It appears that crystalline material (the usual host to associated valuable metals) forms in a quiet environment and as a result of direct nodule association with the underlying sediments.

Jan 1, 1982

By H. Ikeda

The new Onahama N0.3 tankhouse was put into operation early in 1973. This new tankhouse, which has a capacity of 90,000 metric ton cathode per year, is distinct in many important respects from conventional tankhouses. The major objectives in design were to simplify the construction and ope- ration for reduction of the costs for labor, interest and depreciation and also to reduce the copper inventory in the tankhouse by the use of conti- nuously-cast anodes. As a result, the investment cost was decreased by approximately 30% and the inventory cost by approximately 600, while the production per unit area of the tankhouse was increased by 80 - 100% as compared with the existing conventional-type tankhouses at Onahama. By abolition of cell inspection and maximum mechanization of materials handling the labor cost was decreased by as much as 80%. On the other hand, the new system has some disadvantages, such as increase in anode scrap ratio and increased cost of anode casting. The No.3 tankhouse system is, however, still at its starting point, while conventional methods have been continuously improved over the past years of operation. It is expected that the innovational ideas behind this system will serve as bases for a more efficient electrolytic refining system in future.

Jan 1, 1976

By W. E. Straszheim

Computerized microscopic techniques were used to determine the size and identity of the ash-forming mineral components, as well as their association with the organic coal matrix, in order to aid in the development of physical methods of beneficiation which require such characterization for the most effective cleaning. Examples of particle size measurements, mineral phase identification, and especially coal-mineral association results are given for selected samples of raw and physically cleaned coals. These measurements can reveal certain characteristics of coals which can be be of significant value in predicting coal recovery and mineral matter rejection for coals undergoing beneficiation.

Jan 1, 1989

By Zhuo Sheng

We have designed a high-temperature Raman micro-furnace and cell that is suited for the electrochemical process study of the NO3 − in molten NaNO3– KNO3 (fraction of NaNO3 50 wt%) salt. During the cycle voltammetry and constant potential electrolysis process, the Raman laser beam was focused near the electrode; subsequently, the Raman spectra are obtained and the reduction process of NO3 − is analyzed. In the CV cathodic scan process, the new peak attributed to the ν1 mode of NO2 − emerges, and the peaks assigned to superoxide ions (O2 −) and peroxide ions (O2 2−) are not found. In the constant electrolysis process, the peaks at 1130 and 800 cm−1 appear when the potentials are between −2.0 V and −3.2 V (vs. Pt). The results show that when the NO3 − is reduced in molten the NaNO3–KNO3 mixtures, the reduction product O2− cannot stably exist, and O2− will react with NO3 − to form of superoxide ions (O2 −) and peroxide ions (O2 2−).

By K. D. Mondale

The chemical and physical properties of samples from ten sedimentary zeolite deposits. (representing chabazite, clinoptilolite, erionite and mordenite types), have been determined as a prelude to the development of a wet beneficiation process. The mineralogical composition of each deposit and such properties as morphology, size, apparent density, surface area, pore volume, relative hardness and zeta potential in solution have been determined. Some of these properties, especially apparent density and relative hardness, were found to differ significantly from textbook values. Based on differences in properties between the zeolites and their associated gangue minerals, a wet beneficiation process has been developed which makes use of selective grinding, sizing, sorting and gravity concentration. Additionally, an alternative upgrading process using flotation has been developed for one of the deposits.

Jan 1, 1988

By Xuewei Lv, Guibao Qiu, Jiaqing Yin, Chenguang Bai

"The iron ore sinter is one of the main raw materials for the blast furnace (BF) process. In the production of iron ore sinter, the cooling speed of the sinter determines its quality. In addition, the heat recovery devices are installed in the cooling machine for energy saving. The cooling parameters like gas flow rate and the size of sinter should be optimized for getting the gas with a higher temperature and a good quality of sinter simultaneously. In this study, the commercial simulation software COMSOL was used to establish a model for simulating the cooling process of the iron ore sinter. Moreover, three different gas flow rate (1.5, 3, 5m/s) and three different diameter of sintered particles (50, 70, 100mm) were investigated with the model. As a result, in certain porosity, a higher cooling speed was achieved when smaller size or larger gas flow rate was used. And lower gas flow rate was beneficial for the heat recovery. The model could intuitively present the exchange of heat between the sinters and air, as well as the flow and temperature fields during the cooling process.IntroductionIron ore sinter plays a great role in iron and steel industry for many Asian countries such as China, Japan and India. As a part of the sintering procedure, the impact of cooling process on the quality of iron ore sinter couldn't be neglected. On the other hand, the massive iron ore sinters which were at high temperature contain extremely large amount of heat. However, it was reported that there's very few of them recovered in China with an average recovery rate of nearly 10.5% at 2004 [1]. Thus, more reasonable cooling procedure should be developed to get high quality product and heat recovery rate simultaneously."

Jan 1, 2011

By Zhou Jun

Water-quenched samples were taken from a commercial flash furnace at three levels along its reaction shaft during operation at high feed rate. The samples were subjected to a series of analysis and observation. Such processes of the feed in reaction shaft as oxidation, desulfurization, melting, slag and matte formation and etc., variations of particle size along axial and radical direction of the shaft are investigated. The following smelting mechanism in reaction shaft named as “Multi-particle and multi-phase fusion model” is proposed: (1) Fragmentation and collision of concentrate particles take place simultaneously in reaction shaft with particle size growing up. Collision produces large-size “unit melt” which falls into the reaction layer in the settler bath. (2) In the settler reaction layer below the shaft, weak bath smelting reactions take place among the shaft products, producing final matte and slag which separate into two layers. (3) The processes in the shaft are all progressive along the whole height of the shaft. The predominant reaction in the shaft is oxidation, not reduction.

By Stanko Nikolic

The Top Submerged Lance (TSL) technology, developed in the 1970s, is now widely used for the processing of a range of materials. TSL technology for continuous converting was first patented in the 1990s. The process is based on the use of calcium ferrite slag. Although this slag system had been applied elsewhere the phase equilibria had not been thoroughly investigated. This lead to a collaboration between the Process Technology group of Mount Isa Mines, now part of Glencore, and the Pyrometallurgy Innovation Centre (PYROSEARCH) at The University of Queensland. Through multiple research programs this complex system was successfully investigated. The results were then implemented within thermodynamic modelling tools. This combined new knowledge was then applied to the design and industrial implementation of the TSL continuous converting technology, ISACONVERT™. This paper describes the key findings of the research and how this was applied to the industrial implementation of the technology.

The paper concerns an unconventional, yet promising, use of waste magnesite dust and fines. In India a significant amount of this dust is generated from some of the integrated iron and steel industries, refractory and cement plants, during calcination of raw magnesite. However. it is possible to utilize this dust, which is normally a waste, conveniently and economically for the production of magnesium. chemicals. A bench scale study was carried out to determine the rate of formation of sulfated com¬pounds of Mg.Ca,and Fe, inter alla, present in the dust system containing MeO constituents (in which Me=Mg.Ca,Fe,Si,Al etc.) Effects of various process parameters, which affect the reaction rate as also the purity of the product ,were also studied. Some work carried out to develop the process flow charts involving the salient steps to produce magnesium chemicals commercially is reported in the paper .

Jan 1, 1992

By Jun Chang, Jin-hui Peng, Jing Chen, Li-bo Zhang

The leaching of indium from refractory zinc oxide flue dust(ZOFD) is attempted to utilize microwave sulfating roasting process, followed by water leaching. The ZOFD and roasted product were characterized by XRD and SEM/EDS analysis. The effects of various roasting parameters, such as roasting temperature/duration, the proportion of sulfuric acid, as well as the leaching parameters such as the leaching duration and liquid/solid ratio, were assessed. The results indicate that nearly 97% of indium could be leached under the following conditions: mass ratio of concentrated sulfuric acid to ZOFD to be 0.5, roasting temperature of 150 ℃ and duration of 1.5 hours; while the optimal leaching conditions hold at temperature of 25 ℃ for 1 hour, with 4:1 of liquid/solid ratio. The indium leaching rate by the microwave roasting increased by 8% as compared with the conventional roasting process under identical conditions.

Jan 1, 2015

By M. R. Baren

Unpublished results obtained by Baren on thermodynamic properties of sulfur in liquid Fe. Co. Ni. Fe-Co. Fe-Ni. and Co-Ni are reevaluated. correlated. and interpreted on the basis of recent developments in thermodynamics of alloys:. Existing reliable data are reviewed and compared with the? present results. Sulfur obeys Henry's law up to 0.04 mol fraction. and in this range the standard Gibbs energy of solution of sulfur is expressed as a linear function of temperature for each pure metal. The activity coefficient of sulfur in each binary metal solvent 1s correlated with the composition of alloy.

Jan 1, 1983

By Louis J. Mittoni

"It is well known that gas injection systems can exhibit a wide range of dynamical behaviours, ranging from linear periodic bubbling through to highly complex turbulent jetting. Recently, it has been observed that an important intermediate regime exists under certain system conditions, where the dynamics are complex in nature yet predictable for short time periods. This paper reviews the evidence to support the above hypothesis, and discusses the invariant quantitative measures such as density, return maps, Lyapunov exponent and dimension which may be used as pattern recognition features in a mOnitoring and control strategy.INTRODUCTIONThere has been a great deal of research on the submerged injection of gases into liquids. This interest is primarily due to the large number of applications in the pyrometallurgical and chemical engineering industries. Gases are typically injected into liquids to achieve goals such as heat and mass transfer, or physical mixing and agitation. Only recently though has the possibility of using the evolution of the gas dynamics as a probe to internal system conditions been raised [1, 2].At very low gas injection rates and small upstream chamber volumes, gas normally disperses in the form of stable bubbles of constant volume [3]. With increases in gas flow rate, the dynamics become more complex, bifurcating into double bubbling, multiple bubbling and complex coalescence behaviour. Irregularities measured in pressuretime series acquired upstream of the injection port under these complex conditions have usually been treated as bothersome noise or contamination to be filtered from the signal and ignored in the analysis. These irregularities, however, may contain physically interesting and useful information on the system from which they were produced if the system may be classified as deterministically chaotic [4]."

Jan 1, 1996

By Mohamed Y. Bakr, Aly M. Abdel-Rehim

The present work is related with mechanical activation of processing of Egyptian wolframite by simultaneous ball-milling and pressure alkaline leaching, to improve the recovery of tungsten from wolframite. The results show a total recovery of tungsten from wolframite (97.8- 98.7%) by simultaneous ball–milling and alkaline leaching at temperature 175-200oC. It is concluded that processing of wolframite by simultaneous ball- milling and leaching is mechanically activated and accelerated as a result of the grinding action of steel balls that caused the immediate rupture by continuous removing the product layer of the reaction ( sodium tungstate and iron and manganese hydroxides ) from reacting particle surfaces. This leads to the exposing of fresh and activated wolframite particle surfaces to alkaline leach solution and consequently the acceleration of the reaction of wolframite leaching .The results of the kinetic study 0f alkaline processing of wolframite and its mechanical activation show that the system is under kinetic control.

Jan 1, 2015

By J. H. Corrigan

A series of six papers describing the Falconbridge Dominicana Ferronickel project were presented at the International Laterite Symposium held as a joint project of TMS-AIME in February 1979 at New Orleans. A review of the ore mineralogy, as well as. the processing and environmental practices as they exist today at Falcondo with emphasis on modifications put into practice since 1979 are presented in two papers: Part I.- Mineralogy and Ore Dressing E.W. Lithgow - General Superintendent ? Mines Falconbridge Dominicana, C. por A. Bonao, Dominican Republic Commercial volumes of nickeliferous laterite ores overlie part of a 90 km long belt of peridotites in central Dominican Republic. Protores are serpentinized harzburgites and dunites, with lesser serpentinite. The ore mineralogy consists mostly of goethite, serpentine-group minerals, quartz and poorly crystallized, X- ray amorphous materials. Minor constituents are hematite, gibsite, olivine and enstatite. In the Ore Dressing plant, the mine feed is subjected initially to proper sizing and blending to produce a homogenized mix. Subsequent drying and upgrading, by selective crushing and screening of rock kagments through a Barmac circuit, complete preparation of the ore for pyrometallurgical processing. Part II.- Pyrometallurgy, Fuel and Power Generation J.H. Comgan - Manager ? Production Falconbridge Dominicana, C. por A. Bonao, Dominican Republic Falcondo's energy requirements are based on oil which is refined on site to provide distillate to carry out drying and selective reduction of the nickeliferous ore in the shaft furnaces, plus bunker oil to produce electrical power for process melting, refining and ancillary use. The dryer product at 1.68% Ni is briquetted and passed counter current to hot reducing gas in 12 vertical shaft furnaces. The hot calcine discharge is melted in two high power electric furnaces at very high secondary voltage. The crude ferronickel is ladle refined and cast as 15 kg ingots or 125 gm ferrocones.

Jan 1, 1993

By Andreas Weber

Batrec operates a plant for the recycling of used dry batteries with a capacity of 3000 tons per year. The plant Is situated In a tourist area of Switzerland and has complied with all the strict emission restrictions. The process yields four products: FeMn. Zn, Hg and slag. No hazardous waste Is produced. All types of batteries can be treated.

Jan 1, 1995

By R. Parada

A real-time dynamic simulation model has been developed to characterise the flash furnace operation at the Chagres smelter. This model permits the operators to plan the process to meet the Peirce Smith converters' schedules and feed the acid plant with gases that satisfy its best operating efficiency range. Essential control parameters for the furnace (process air enrichment, oxygen coefficient and supplementary heat) are calculated to satisfy process targets such as matte grade, slag silica and matte/slag temperatures. These calculations are carried out with a real-time simulation. Flash furnace control and operational stability permits setting up control strategies that streamline the flow of copper to converters and of sulphur to the acid plant.

Jan 1, 1999

By Miguel N. Herrera

The electrochemistry of coal pyrite is relevant to coal desulfurization by chemical or bacterial leaching, flotation and oil agglomeration. The electrochemical behavior of polished and etched Upper Freeport and Pittsburgh coal pyrite samples was investigated from pH 1.0 to 10.5. The open-circuit potentials decreased with increasing pH, as expected, but were well above the thermodynamic stability region of pyrite, and decreased with time. Cyclic voltammetry revealed behavior highly sensitive to pH and scan rate (2.0 and 20.0 mV/s). The behavior on the first cycle was always substantially different from that on subsequent cycles. The anodic and cathodic reactions were correlated with the Eh-pH diagram for the Fe-S-H20 system to identify the reactions occurring at different pH values. There was also evidence that the buffers used to maintain basic pH values are themselves electrochemically active, which should be considered in interpreting many earlier electrochemical studies of sulfide minerals.

Jan 1, 1994