Search Documents

By H. Maleki

Gob pressure measurements were made in a Western U. S. coal mine as part of a long-term program to evaluate cave progress and to determine the influence of geological discontinuities on caving conditions, load transfer, and resulting instabilities. Gloetzl cells were selected for the measurements due to their simple, robust construction and a history of being able to monitor pressures in a broken medium. A methodology was developed for the successful installation and protection of the cells and hydraulic lines in the gob as the face retreated. The measurement indicated a cave progress controlled by the frequency of, major faults. The pressure-mining progress profile was compared to those observed in other parts of the world. It was concluded that the significant differences in profiles was caused by the thick-bedded strata, the existence of high lateral stresses and the spacing between faults. Recommendations are given for future applications of Gloetzl cells for gob pressure measurements.

Jan 1, 1984

By David P. Conover

The effects of stress distribution on pillar stability were evaluated through rock mechanics studies conducted in three underground room-and-pillar coal mines. Results of the three field instrumentation programs are presented to illustrate the use of borehole pressure cells to determine vertical stress distribution in coal pillars at various stages of mine development. Vertical stresses and stress changes are determined using methods developed at the Bureau of Mines. Measured stress distributions are compared against theoretical distributions and possible explanations for observed behavior are discussed. Results indicate that stresses and stress changes calculated from pressure cell data are inconsistent with theoretical values; however, the data are useful for qualitative evaluation of trends over time. Calculated values are found to be sensitive to coal properties and initial setting pressures of the cells.

Jan 1, 1989

By Axel Preusse

A high advance rate of the longwall face increases inevitably the mining dynamics within the rock and on the surface. Measures to limit the mining dynamics are the adjustment of the face advance rate to stretch the influences of mining over time and continuous winning to maintain a uniform influence of mining. This paper deals with the dynamics of mining subsidence within the range of a transmission overhead line for transportation of gasoline, diesel, kerosene, heating oil, mineral oil and other hydrocarbons. In a certain segment of the 24"-pipeline it was possible to predict, due to technical, operational and laying conditions, that undermining the pipeline would cause local stress maxima within the pipeline string. To limit these expected local stress maxima, the face advance rate of panel 497 was adjusted to the sensitivity of the pipeline towards the influences of mining. Comparison of the predicted mining dynamics, using the theory of stochastic media, with the measured ground movements led to the conclusion that the effects of dynamical influences which occurred within the range of the transmission overhead line and acted on it were low. This confirmed that the decision to adjust the face advance rate to the sensitivity of the transmission overhead line was correct (Kateloe et a)., 2002). A later relaxation cut in range of the pipeline siphon scarcely produced relaxation movements of the pipeline. The appointed sensitivity data of the undermined pipeline and the according maximum admissible face advance rate were thus correctly measured.

Jan 1, 2003

By William Gray

It has been ten years since the Mine Safety and Health Administration (MSHA) promulgated a safety standard requiring the use of Automated Temporary Roof Support (ATRS) systems in underground coal mines. The use of ATRS systems with roof bolting machines and continuous miners equipped with integral bolters has all but eliminated fatal roof fall accidents associated with manually setting temporary roof support. The last ten years have seen an evolution of the ATRS systems themselves and of MSHA's policy regarding ATRS systems. These changes are a response to operational and safety issues regarding ATRS systems often brought about by the ever-changing coal mining environment. As a result, MSHA's Technical Support personnel receive numerous inquiries from all segments of the coal mining industry on various ATRS topics. These requests for technical assistance range from an interpretation of a facet of the ATRS standard to an in-depth evaluation of a prototype ATRS system. This paper will address the aforementioned evolution of ATRS systems and will also summarize the factors MSHA Technical Support uses to evaluate these systems in the field. In addition, some of the more common misconceptions regarding the design, use, and regulatory requirements regarding ATRS systems will be covered.

Jan 1, 1998

By Pier Paolo Manca

The investigated area lies close to a large town and covers an area of about lkm2. The mine was worked at depths ranging from 5 to 100 meters but mining operations actually ceased some 50 years ago. There are seven coal seams, each one to two meters thick, overlain by sedimentary rocks in a strongly faulted area. Different kinds of subsidence have occurred, crown holes, shallow depressions and hummocky ground. The results of rock mechanical characterisation (RMR method) in the area have been used to define three different types of numerical model (FLAC 2D). A large numbers of simulations has been performed to solve three different problems at three different scales: to determine the, mechanical properties of the roof rock and overburden involved in the subsidence process, to assess the crown hole subsidence potential and to define the properties of the beam foundations.

Jan 1, 1999

By S. S. Peng

This paper presents a convenient way for the preliminary design of the shield supports. The locus equations which are applicable for all kids of shield supports are derived. These equations facilitate the statics analysis of the shields. An indirect method in determining the coefficient of friction, the external toads and their locations are also developed.

Jan 1, 1982

By T. L. Dobecki

As a means of demonstrating the effectiveness of reflection seismology in determining continuity of coal seams, three U. S. field projects are reviewed. The three projects involve coals of varied thickness (2-14m) and age (Pennsylvanian to Eocene) from three coal areas of the U. S. (Pennsylvania, Wyoming, and Washington). Each project also employed its own particular seismic technique, recording system, and seismic energy source although all are considered state-of-the-art, high resolution, digital seismic surveys. Project 1 (thin, Pennsylvania coal) sought detection of sand channels using dynamite and standard in-line (2-D) seismic technique. Project 2 (thick, Wyoming underground coal gasification) involved a gas-explosion (Dinoseis) source with areal (3-D) acquisition methods. Project 3 (thick, Washington underground coal gasification) employed a shotgun-type source and standard in- line methods. Data processing was handled by different contractors for each project. Each project was successful in accomplishing its own particular objective; however, data quality and interpretation seem to be more a function of thickness of the target seam, complexity of the overburden, and processing contractor than a seismic source, acquisition scheme (2-D versus 3-D), or recording instrumentation.

Jan 1, 1981

This paper presents a two-dimensional numerical procedure which incorporates concepts related to the mechanics of strata deformation' as well as' empirical indices associated with subsidence engineering. Regional deformation data were employed in order to establish overburden deformation zones, while material properties were kept constant. Scaling of final displacements was based on empirically predicted values for subsidence and strain for the Appalachian coalfield. The model was validated with a number of regional case studies and predicted subsidence and strain curves were compared to those obtained using the semi-empirical influence function formulation developed by VPI&SU.

Jan 1, 1988

By Venkata S. Vutukuri

Compressive strength of cylindrical specimens of a model material and sandstone with various diameter/height (d/h) ratios was determined in unconfined compression tests. It was observed that the compressive strength increases with increase in d/h ratio. Triaxial compression tests were also conducted on the specimens of the same materials with a d/h ratio of about 0.47. It was observed that the axial stress at failure increases with increase in confining pressure. A very interesting correlation was found between the effect of d/h ratio on compressive strength in unconfined compression tests and the effect of confining pressure on axial stress at failure in triaxial tests. The relationships between d/h ratio and confining pressure, s3 in MPa are:- For model material - s3 = -0.95 + 1.7957*(d/h) 0.7883. For sandstone - s- (-0.4554 + 0.9888* (d/h) 1.0355. The correlation coefficients for these equations are 0.9997 and 1. These equations are valid for d/h ratios of up to 10.

Jan 1, 1993

By G. K. Rogers

Portals, which are the surface entrances to underground excavations, are frequently overlooked and often difficult areas In terms of ground control. Failures commonly occur In the typically high angle approach cuts and Initial subsurface portion of the portal. In order to permit rigorous design of all types of portal structures, failures are Identified and subsequently classified. Based on the failure classification and suggested analysis methodology, optimum ground and support loading can be determined.

Jan 1, 1988

By H. N. Maleki

Tension-torque relationships were investigated *n a coal mine for bath standard 5/8 in. (16 mm) bolts and a vibrating wire instrumented bolt, using conventional and controlled installation techniques. The instrumented bolts differed from the standard bolts by their head size and hole preparation procedures. The controlled installation technique developed by the U. S. Bureau of Nines (USBN) involved using hardened washers and lubrication in the bolt assembly, and maintaining a minimum thrust level during bolt installations. The object of this study was to determine the tension to torque ratio (lb/ft-lbs; for standard bolts and instrumented bolts for both conventional and controlled installation techniques, and to modify the bolt assembly so that the ratios would be equal for the instrumented and standard bolts for both installation techniques. It was shown that the instrumented bolts installed in faced holes had a similar tension torque ratio td that of standard 5/8 in. (16 mm) bolts installed in unfaced holes for each installation technique, and thus they were representative of other uninstrumentea bolts. This was achieved by evaluating the influence of several factors oh the relationship, including: facing the hale surface, introducing washers and lubrication in the bolt assembly, and applying different levels of thrust at installation due to bolter operator practice. The tension to torque ratio fur conventional bolts was only 21 (lb/ft-lb) for the coal mine, resulting in an installation tension of 4000 lbs (17.8 kg) with the typical installation torque of 150 to 400 ft-lb. This tension level was approximately 50 percent of the required bolt tension, and thus, it was concluded that torque standards are not sufficient to assure adequate bolt tension. .he low tension levels were due to the particular wait hardware in use, operator practice, and bolt fencing.

Jan 1, 1984

By Karl H. Brandt

In the Auguste Victoria mine a bolted rectangular roadway has been kept open for the first time in the seam D/C after retreat. The target of the project was to gain a basis for planning and experience for future mining layouts in the same scam in view of the reuse of boated rectangular roadways. For this the roadway was additionally secured in sections with longbolts before the influence of the retreating panel had taken place. On retreat a concrete sidepack was concurrently put in place on the face side. The installed monitoring systems consisted of endoscopic devices, multiple extensometers (Tell-Tales), shear-tales, extensometers and convergence measurements. The experience that was gained was carried over into a physical and numerical model.

Jan 1, 2001

By Axel Preusse

This paper shows basic considerations about the prognosis and prediction of surface subsidence and other ground movements in the German hardcoal industry. The following case studies describe experiences collected in projects between university and industry.

Jan 1, 2000

By Kikro Matsui

Longwall mining 1s more productive in comparison to other methods but requires particular conditions for its effective use This paper relates to longwall roof instability at Ikeshima Colliery In order to make clear the cause of the longwall roof instability, scientific investigation in terms of geomechanical factors and longwall support system was planned and carried out

Jan 1, 1997

By Syd S. Peng

Full-face shield leg pressures in a longwall panel for a three-month period were collected and analyzed. The pressure data were presented in the following forms: full- panel full-face shield pressure, individual shield pressure, full-face shield pressure, full-panel time-weighted-average pressure, and relationships among setting pressure, final pressure and pressure increment. Although shield pressure varies from shield to shield and from cycle to cycle, the setting pressure and face advance rate do control the 6nal pressure and time-weighted average pressure.

Jan 1, 1997

By John J. Bowders

The stability of surface slopes undergoing subsidence due to longwall mining was investigated to examine the effect the subsidence had on the stability of the slopes. Stability analyses were performed on all slopes along both longitudinal and transeverse sections of the longwall panel before and after subsidence. Both finite- and infinite-slope analyses were performed with both drained and undrained cases. The results indicated that the changes in the stability of slopes due to subsidence were insignificant for the cases analyzed. Although significant lateral ground movements were recorded, these were not attributed to slope failure. Explanations for these movements are presented in the paper.

Jan 1, 1988

By Douglas Morrison

By applying modern 3D numerical modelling techniques to the analysis of a pillar cascade failure in a room and pillar mine, it has been possible to simulate the collapse and develop an understanding of the role of low rock strength areas within the mine. The cascade collapse occurred in a normal strength area but would not have occurred without the influence of a low strength rockmass in one section of the mine. The numerical analysis made it possible to develop a realistic assessment of the residual pillar strength. With the introduction of regular empirical pillar performance assessments, critical pillars or groups of pillars can now be identified proactively. This has led to an aggressive extraction ratio of 90% that manages pillar failure, avoids pillar and roof collapse and prevents surface subsidence. Since the mine also has significant waste products, the use of backfill for ground support has made it possible to significantly improve the performance of strategically located pillars, and so achieve even higher extraction ratios.

Jan 1, 2003

By Yi Luo

The potential influences of mining subsidence on structural stability, integrity and functionality of guyed tower structures have not been systematically studied before. This paper presents a ease study where a guyed steel tower of a telecommunication company was mined under by a longwall operation. Prior to mining, every aspect of the subsidence influences to this structure was studied. The pre-mining assessment indicated that the structure could experience vibration problem in the second half of the dynamic subsidence process. Bawd on the study, a simple mitigation measure was recommended and implemented and the structure was successfully protected.

Jan 1, 2003

By Daniel W. H. Su

A floor-bearing capacity test apparatus was designed and constructed to determine the true bearing capacity of soft floor materials beneath coal pillars or longwall face supports. The apparatus has been employed in entries up to eleven feet in height. Results of in-mine floor-bearing capacity tests suggested that the ratio of the soft fireclay thickness to the bearing plate width and the moisture content in the fireclay were the most critical parameters affecting the ultimate bearing capacity. Foundation engineering principles were applied to interpret the field test results to estimate the floor-bearing capacity beneath longwall face supports.

Jan 1, 1993

By Chris Adams

The application of pre-tensioned tendon roof support assisted Harworth Colliery in their revival, from impending closure to lowest cost deep-mined producer in the UK, over just six months last year. The paper describes this success story, how it came about, the reasons "why", and the method "how"

Jan 1, 2003