Search Documents

By Baisheng Zhang

The definition of Ultra-close multiple seams as defined by the floor disturbance depth, h, due to mining in the upper seam is proposed: it refers to those coal seams that are spaced very closely, i.e. h,, the distance between seams, is small or equal to h, , and mining of any one of the seams will significantly affect the others. Those seams are called the ultra-close multiple seam group. Theoretical formula for defining it and practical examples are given in this paper. Underground measurements and numerical analysis show that in ultra-close multiple seam mining, the characteristics of ground pressure due to lower seam mining is different from that of single seam mining. The major differences is that the roof, as a result of damaged caused by the upper seam mining, is full of factures; the roof broke up in the belt entry and fell down easily; support loading at the face was small without clear periodic weighting phenomenon. Based on these results the roof structure model and roof control theory for ultra-close multiple-seam are established.

Jan 1, 2005

By Wenjun Ju

It's very important to determine the limitation of bed separation in entry roof in order to predict roofs stability and take some necessary precautions. Based on numerical modeling and monitoring in the field, the new concept of Limitation of Roof Layer Separation (LRLS) and its method of determination LRLS is given in this paper

Jan 1, 2001

By André C. Zingano

The domino effect in a violent pillar collapse occurs due to the redistribution of stress in the remaining pillars near the collapse, and this stress transfer occurs in the immediate and main roofs. The remaining pillars do not have enough load capacity to support this overstress and also fail, and the domino effect propagates further to the entire panel. The domino effect does not occur only due to low load capacity of the pillars, but also the roof rock mass quality, because the stress is transferred by the roof. In high competent roof without discontinuity (fault), like massive sandstone seam, the deformation of the roof is the cause of pillar collapse extension and propagation. Depending on how close it is approaching the collapse limit; the immediate and main roofs behave differently. When it is close to the collapse limit roof convergence and pillars compression occur. Conversely when it is far from the collapse limit divergence and pillars decompression occur. This is called the arc-effect. This paper studies this behavior of the roof (immediate and main roofs) using numerical modeling to simulate the roof deformation and stress distribution in the roof and pillars. This simulation represents the progression of pillar collapse and shows the zone of convergence and divergence of the roof, and also the effect of this behavior on pillar confinement. Two-dimensional plain strain model was applied to simulate the arc-effect. The simulation results were compared to those of the instrumentation that was installed before the collapse. Keywords: pillar collapse, room and pillar, numerical modeling

Jan 1, 2005

By Ryan Garvey

A numerical investigation is made into unstable failures of coal pillars (i.e. coal bumps) using the finite difference software FLAC3D. A static energy balance is first derived to calculate the excess energy released as a consequence of unstable failure in rock. Two- and three-dimensional mining layouts are then assessed on their bump-potential based on the magnitudes of excess energy released during simulated pillar failures. A three dimensional pillar model is developed to represent tributary area loading of an infinite room-and-pillar layout. Pillar strength and brittleness characteristics are calibrated using a Mohr-Coulomb strain-softening constitutive law to simulate width-to-height ratio coal pillars ranging from 1:1 to 5:1. Width-to-height ratio pillars 1:1 to 3:1 release large magnitudes of excess energy as the pillars fail, representing massive collapse of room-and-pillar layouts. The larger pillars maintain their residual strength during failure; however significant excess energy is still released during temporary reductions in pillar strength. A two-dimensional model is then constructed of a gate road pillar failing due to elastic rebound of the surrounding rock mass. Soft loading conditions initiate unstable failure for all pillar widths, while the total magnitudes of excess energy increase with the size of pillar being modeled. The results from these tests indicate that excess energy may be used as a direct assessment of the bump potential of simulated mine layouts.

Jan 1, 2013

By Jingyi Cheng

Many longwall panels in China are laid out along the dip direction such that the direction of longwall retreat mining is along the strike direction of coal seams. Downward mining longwall panels in steeply inclined seams refers to those that are laid out in a non-uniformly developed fold structure where the seam is not only steeply dipping, but also highly undulated along the strike direction, causing longwall mining extremely difficult because it has to deal with large dip angles that vary both in the mining and faceline directions. Obviously, the characteristics of mine pressure and overlying strata movement in downward mining longwall panels in steeply dipping seams have unique patterns that are very much different from those cases of mining the flat or gently inclined coal seams. The effects of those unique patterns presented a big challenge to production and safety. Almost all previous and current researches on ground control have been concentrated on issues related to the flat and gently inclined coal seams. Conversely, research on steeply inclined coal seams, especially those with large angle variation both along the seam dip and strike directions is almost none. Therefore, it is very important to initiate a study to better understand the characteristics of mine pressure and overburden strata movement for this special type of geological condition. The objective of this paper is to monitor and analyze the characteristics of mine pressure and overlying strata movement in downward mining longwall panels in steeply inclined seams, the angle of which varies greatly along both the seam dip and strike directions. The measured data has conclusively demonstrated that the characteristics of mine pressure and overlying strata movement in downward mining longwall panels in steeply inclined seams are different from those for the flat and gently inclined coal seams. The large downward angles of coal seam undulation along the strike (mining) direction can obviously affect the roof movement and reduce strata pressure. Study in this research showed that appropriately increasing the rate of mining (or face advance) is positive to roof control.

Jan 1, 2013

By Jian Yong Chen

The results of a laboratory investigation of pullout tests conducted on grouted, plain cable bolts are reported. The main purpose of the study is to determine experimentally the shear bond stiffiess of cement grouted and resin grouted cable bolt systems, which is an important input parameter for numerical modeling of cable bolt support. Three nominal embedment lengths of 152mm (6 inch), 203mm (8 inch) and 254mm (10 inch) were used and two types of grout namely cement and Anchortite resin were used. Two water- to-cement ratios of 0.3 and 0.4 were employed for the cement grout. The concepts of effective shear stress and effective shear stiffiess are explained and adopted to calculate the shear bond strength and the elastic shear bond stiffiess per unit length. A comparison of results with previous research is presented to reveal the effect of water-to-cement ratio and embedment length on the shear bond characteristics of grouted cable bolts.

Jan 1, 2005

By Shugang Li

The layout and efficiency of the degasification system is heavily dependent on the distribution of and the methane migrating mechanism in the mining induced fractures in the overburden strata In this paper, physical modeling and numerical simulation are employed to study the mining-induced fracture zones and the stress distribution in these zones. The physical models show that both the fracture and compaction zones form a parabolic shape in the over- burden strata along the panel transverse direction. When this is generalized to the panel longitudinal direction, the shape of the mining induced fracture zone over the longwall gob can be represented by a 3-D elliptic paraboloid function. Through the observation of bed separation, fracture density and distribution pattern in the physical models, it is believed that the development of the parabolic fracture zone can be divided into three distinguishable phases. The expansion characteristics and sizes of the fracture zones can be estimated. The numerical stimulation studies can be used to estimate the extent of the stress release zones. The stress release zones can be also divided into a high compressive stress - fracture closure zone, stress relieved - fracture expansion zone, and intact zone. The methane desorption model is then used to analyze the methane migrating pattern in the fracture zone. The developed model has been verified by the results of a longwall gob degasification tests at a coal mine in Yangquan, China with a fair agreement. Such studies show that the model can provide a reasonable accurate tool for designing the gob-well degasification system for longwall mining operations.

Jan 1, 2005

By Dion Pastars

Resin based grouts are the main form of rock bolt anchorage in the underground coal industry in Australia and New Zealand. To be effective, the system requires the mixing of the catalyst and mastic components of the resin, as well as shredding of the laminate cartridge that contains the resin. An unknown measure is the load transfer characteristics of a bolt where the resin is well mixed but remains encased in the cartridge (gloved). Laboratory and in situ field investigations have been undertaken to quantify the performance loss due to mixed gloved bolts. This work showed repeatable results, indicating serious performance loss of the gloved and mixed system, with load transfer approximately 10- 15% of a non-gloved system (MacGregor, 2004). The in situ testing has demonstrated the relationship between the adhesion qualities of the resin and the mechanical interlock generated by radial confinement with progressively increasing tensile load. Effective load transfer is defined by the ability of the system to sustain shear stress on the bolt hole wall.

Jan 1, 2005

By Peter Zhang

Room and pillar mining under shallow depth is usually conducted with a high extraction ratio, which leaves small pillars with a low safety factor in some old workings in abandoned mines. Pillar sloughage, squeezing or even collapse may have occurred in those old workings with small pillars, either at the time of mining or later. The conditions of the pillars in abandoned mines can affect mining above them. Subsidence fractures and abutment pressure are indications of multi-seam interaction caused by squeezing or collapse of small pillars. To mine over areas with potentially unstable small pillars, the panel layout in the upper seam should be such that multi-seam interaction can be minimized and proper roof and rib support should be installed in the influence zones. This case study presents an example of multi-seam mining above small pillars under a shallow depth of cover. Though the interburden is relatively thick and competent, interaction is still present over the influence zones. Pillar stability and multi-seam interaction analysis, numerical modeling and in-situ monitoring are presented to demonstrate how the upper seam can be mined safely over the small pillars.

Jan 1, 2014

By R. Kaund

"Quantifying the rockburst consequence is of critical importance to reduce the hazards with preventative measures in underground mines and deep tunnels. Contours of energy components within a pillar model are plotted at different rockmass damage stages, and plastic strain work and released energy are proposed as indicators of rockmass damage consequence. One pillar model under different loading stiffness is simulated to assess indicators of pillar burst and the resulting damages. The results show the rockmass damage under soft loading stiffness has larger magnitude of plastic strain work and released energy than that which is under stiff loading stiffness, indicating the rockburst consequence can be quantified with plastic strain work and released energy in numerical models. With the quantified rockburst consequence, preventative measures can be taken to avoid severe hazards to mine safety.INTRODUCTIONWith the increasing demand of mineral resources and depletion of near-surface ores, the depths of underground mines have made the mining activities one of mankind’s most dangerous types of work (Ortlepp, 2005). The Mine Safety and Health Administration (MSHA) defines rockburst as “a sudden and violent failure of overstressed rock resulting in the instantaneous release of large amounts of accumulated energy.”The types of rockburst can be classified into three types: (1) strain burst, (2) pillar burst, and (3) fault slip (Müller, 1991). Strain burst is the most common type of unstable rock failure in underground openings, where the intensity and scale are usually smaller than pillar burst and fault slip (White and Whyatt, 1999; White, Williams and Whyatt, 2002; Ortlepp, 2005). The cause of strain burst can range from shattering of rock under high stress concentration to buckling of discontinuities parallel to underground openings. The occurrence of pillar burst also depends on the stress and discontinuity conditions in the rockmass, but pillar burst usually involves the sudden loss of strength in the core or foundation of a pillar (Whyatt and Blake, 2002; Kias and Ozbay, 2013; Khademian et al., 2016). Fault slip or slip burst can be either slip along pre-existing discontinuities or shear failure in the rockmass, when the shear stress is larger than shear strength in the fault (Rice, 1983; White and Whyatt, 1999; Sainoki and Mitri, 2014). The consequence of fault slip can vary from very small rockmass damage to consequential rockmass damage, but large seismic magnitude does not always result in large rockmass damage (White and Whyatt, 1999; Whyatt and Blake, 2002)."

Jan 1, 2018

By Anton Sroka

The dimensioning of shaft safety zones is a substantial task of mining subsidence engineering. On the one hand, the coal reserves in shaft proximity are to be mined as complete as possible, because they can be made accessible economically. On the other hand, the maintenance of the shaft operation is to be ensured at each time, since shafts represent the most important link between underground and aboveground. Regarding these two criteria, this publication presents a model for the optimization of shaft safety zones. Beyond that, extraction methods in shaft safety zones are described, in particular with consideration of minimized mining influences on the shaft.

Jan 1, 2005

By E. Bane Kroeger

In underground coal mining, there is often a need for supplemental support for mine openings. In the past, one of the most common types of supplemental support was wooden posts that were installed against the roof using opposing wooden wedges. Underground, wood has the tendency to shrink from moisture loss and dislodge if not under load. Another drawback to using wood is the variability in strength between posts. Defects in the wood such as knots can cause weaknesses that often lead to premature failure of supplemental support. Many mines that install large amounts of supplemental support in certain areas of the mine such as bleeder entries in longwall mining have switched to using steel props rather than wood posts or cribbing. The reactions of steel props under loading are well- defined and there is little variability in strength between props. Steel props and can be fabricated so they can be used in a variety of roof heights without modification. Wooden posts often have to be cut to a usable length underground before installation. This adds to the installation time of the wooden posts. Steel props are more compact and can be lighter than their wooden counterparts, depending on the length and carrying capacity. Often times it is desirable to prestress the supplemental support to improve roof stability. This is often problematic and time consuming with some types if supplemental support. With these factors in mind, research was undertaken at Southern Illinois University Carbondale (SIUC) to design a new steel roof prop. Several new clamping designs were developed and prototypes were fabricated and tested in the labs at SIUC in the spring of 2003. The designs were modified and refined and the first full-size prototype roof prop was tested in January 2004. With the success of the full-size prototypes, a cooperative research program was established between SIUC and Excel Mining Systems, Inc. to further develop the new prop. Development went smoothly and the prop has performed as expected. In February 2005, SIUC and Excel entered into an exclusive licensing agreement. The prop design under license, the K-Prop, will be installed using a lightweight portable hydraulic jacking system under design that can be used to prestress the props, applying load to the roof and floor during installation. By varying the installation load, the prestress load can be varied from about 1,000 to 10,000 pounds (4.448 to 44.48 kN) and at the same time, the carrying capacity of the K-Prop can be varied from 10,000 to 100,000 pounds (44.48 to 444.8 kN). The K- Prop is composed of only 3 pieces and laboratory testing has suggested that it can be installed by a pair of workers in less than two minutes. The speed of installation of the K-Prop should significantly reduce the total installed cost for supplemental support and should provide a safer working environment by prestressing the prop, which will add support load to the roof and floor during installation.

Jan 1, 2005

By Shuangsuo Yang

Coal ribs can roughly be divided into three types: (1) roof and floor rocks are similar to ribs, (2) roof and floor rocks are stronger than ribs, and (3) roof and floor rocks are weaker than ribs. Different types of roof/floor and ribs will exhibit different types of ground pressure around an entry. Most coal mines belong to the 2" type with ribs fractured or even broken. In this case the mine ground pressure depends on the occurrence and development of deformation and fracture of the ribs. If it's not properly controlled, the following deteriorating process will follow: the roof bent downward > the ribs squeezed and broken > rib sloughing and collapse > rib support to the roof reduced > the roof bent downward further > the ribs broken further. In this paper rib instability is divided into four types: compression/shear sliding rib fall, gravity sliding rib fall, cross arch rib fall, and cleavage rib fall. Since failure in thin walls is largely of tension type whereas that of thick walls by compression or shear, a concept is proposed here to utilize a thick bolted rib to stabilize entry ribs, i.e. the thickness to height ratio of the thick bolted ribs

Jan 1, 2005

By Denise Müller, Axel Preusse

"Due to multilateral underground use, mining subsidence is discussed more and more with regard to issues other than mining, such as post-mining topics, storage, or geothermal use. These discussions and the influence of the energy policy is why the situation in Germany is described as a transition from active to abandoned mining. Many PhD theses have been written within the last 20 years—every single one with a different topic but all with the same issue—the effects and challenges of mining subsidence.These challenges start with the research regarding geological and hydrogeological conditions, which is the basis for calculations like the angle of draw or predictions of subsidence due to water table drawdown. Furthermore, the research investigates issues like risk-management and financial planning. One of these issues is post-mining calculations; others include potential hazards of storage or the use of geothermal energy.This paper outlines an overview of German mining and the consequences due to subsidence. It deals with an overview of the circumstances related to hard coal mining, lignite mining, the use of geothermal energy, gas, and opportunities regarding underground storage. Basically, it describes the essential steps of processing mining subsidence, starting with monitoring to forecast and up to safety measures.With a glance back to the applied research of the prior two decades, we compare given forecasts with experiences already gained.Even though mining decreases, ground control does not.INTRODUCTIONAfter the Second World War, an economic recovery started in Germany, during which the mining industry provided an advantage. Areas like the Ruhr District or Saarland were characterized by hard coal mining. In addition, there was lignite mining in the Rhenish mining area and the middle German coal district. In the Lausitz area, there were gravel and sand companies for the construction industry and many other medium-sized mining companies. Especially in the Ruhr District and in Saarland, where large coal fields were built, mining played a major role. The number of mines increased, and the negative effects on the terrain got bigger. While minor open pits or quarries have influences on the landscape only, large open pits and underground mining lead to significant ground movements. This results in a larger importance of mining subsidence engineering. Calculations of subsidence and forecasts have been developed and refined within the last several years. Due to the fact that the mining areas were and still are densely populated, the forecasts are getting more and more precise."

Jan 1, 2018

By Luis Giraldo

Rock bolt installation characteristics near roof falls have been identified as contributing to failure. One documented and regularly occurring failure mechanism is loss of anchorage between the grout and the rock wall of the bolt hole. Key contributors to the integrity of the grout interlocking with the rock mass are the diameter of the hole relative to the diameter of the bolt, resin versus cement type grouts, rock type, and condition of the hole. Smooth bolt holes consistently exhibit less rock bolt load bearing capacity than rough walled holes. The goal of this study was to quantify the benefits of borehole conditioning and develop a systematic approach that would allow improvement of roof bolt performance. A new rock drilling technology, the Helical Drag Bit (HDB), was used in the early stages of this project to condition the borehole. The HDB cuts a prescribed helical groove in the borehole wall. When a bolt is grouted into a hole that has been conditioned using the HDB, the grout fills the helical groove and provides a stronger, more reliable mechanical lock between the rock and the grout. This paper presents results of a series of tests conducted in the laboratory and in the field. Short encapsulation pull out tests have demonstrated considerable increase in pull out strength and more consistent bolt performance when hole geometry is modified using the HDB. The results have also shown that greater load bearing capacity improvements are obtained in mines with weak roof rock, where it is most needed. Additionally, bolts recovered for examination suggest that hole conditioning during roof bolting reduces the effects of finger gloving. Therefore, mines with stronger roof rock could also benefit from hole conditioning. A new roof bolt that uses the HDB principle has been designed and tested. The new system works with existing bolting equipment requiring minimal modifications to the traditional procedure used for installation of fully grouted rebar bolts. The use of these higher anchorage capacity bolts will allow mines to reduce severe injuries and fatalities resulting from ground failures while maintaining or increasing productivity.

Jan 1, 2005

By Michael Trevits

The NIOSH Lake Lynn Laboratory (LLL) is a unique research facility, located about 50 miles southeast of Pittsburgh, Pennsylvania, that is designed to provide a full-scale mining environment for testing and evaluation of mine health and safety technologies. The LLL occupies more than 400 acres and is composed of surface test and training areas and an underground mine. The Lake Lynn Experimental Mine (LLEM) was built at an abandoned commercial limestone quarry where surface mining ceased in the late 1960's. Later, new underground development was constructed to simulate modern-day coal mining scenarios; including room-and-pillar and longwall mining layouts. In January 1994, a sinkhole opened southeast of the No. 4 Portal of the LLEM and since then, the area of the underground failure and surface deformation has continued to expand and now includes several interconnected sinkholes. A concern developed that the overburden instability could expand and affect the structural integrity of the nearby highwall and the No. 4 Portal. It was unsafe to conduct a detailed underground survey of the mine in this area because the mine roof conditions near the No. 4 Portal had deteriorated significantly. It was decided to investigate the overburden conditions near the No. 4 Portal using ground penetrating radar (GPR). A GPR survey grid was located along an access road that passes over the top of the portal. To delineate the mine conditions near the portal, antennas whose frequency spectra produced pulses centered near 100- and 200-MHz were used. The results of the GPR survey suggests that the overburden rock units appear to be laterally consistent to a depth of about 15-ft. Below that point, the overburden appears to be significantly disturbed and it was hypothesized that this area contains a large roof fall. A follow-up ground truth survey of the mine roof conditions was conducted from the mouth of the portal. It is concluded that the observations and measurements made from the radar records appear to be correct as a large roof fall was observed and measured from the mine portal area.

Jan 1, 2005

By Syd Peng

In designing a proper roof support system, one must know the features of roof geology in advance of mining. The drilling parameters obtained during normal roof bolt installation cycle can provide a large amount of information on the roof geology when properly interpreted. It is also an economic way for identifying the geological features of the roof. This research develops a method for predicting the roof geology based on the drilling parameters obtained during roof bolting operation. From the results of a series of laboratory and underground tests, feed pressure is found to be a good indicator for identifying the voids/fractures and estimating the roof rock strength. This paper describes the method for determining quantitatively the location and the size of void/fracture and estimating the roof rock strength from the drilling parameters of roof bolter.

Jan 1, 2005

By Jisheng Han

Interaction effect exists when two or more neighboring seams are mined. The mining activity in one seam causes stress redistribution and strata movement in both the roof and floor. When the thickness of interburden between two neighboring seams is small, some hazardous situations like roof cutters, roof falls, floor heave and rib spalling in one seam may be encountered due to the effect of the mining activity in the other seam. An investigation about roof cutters, roof falls and floor heave was conducted in a West Virginia mine to study the interaction of multi-seam mining. The mine is mining the Sewickley Seam, which is about 90 ft above the Pittsburgh Seam which was mined in the 1960's using room and pillar method. The roof falls and other stability anomalies of entries observed underground in the Sewickley Seam were found closely related to the location of barrier pillars and gas well pillars left in the Pittsburgh Seam. Then numerical modeling was carried out to check the interaction between these two seams of mining. It was found through the modeling results that in the areas where pillaring operation was conducted in the Pittsburgh Seam, the stress concentrated less in the Sewickley Seam while near the edge of the gas well pillars and barrier pillars, high stress concentration was observed. It was concluded that under the geological conditions of the study mine, the entries stability would be affected by the lower seam mining activity, especially above or around the edges of pillars.

Jan 1, 2005

By Dr. Daniel W. H. Su

t is both an honor and privilege for me to nominate Dr. Daniel W. H. Su for the inaugural Syd S. Peng Ground Control in Mining Award. I can think of no better candidate than Daniel that is deserving of this award ? an award to recognize technical excellence in advancing ground control technologies [and] approaches. Daniel?s education and career spans over three decades. Having graduated from National Cheng Kung University in Taiwan in 1972 with a B.S. degree in Mining and Petroleum Engineering, he spent the next four years in the Taiwanese military and mining industry, before moving to the United States, where he enrolled in West Virginia University?s Mining Engineering Department. He received his M.S degree in Mining Engineering from WVU in 1978; then in 1982 became the first person to ever receive a Ph.D. in Mining from WVU. His thesis was titled, ?Development of Ultrasonic Techniques for the Measurement of In Situ Stresses?.

Jan 1, 2006

By Yundong Ma

In this paper the dynamic process of rock deformation and failure in the roadways of the #9 coal seam, Wuhushan Coal Mine by was simulated using the software "Rock Failure Process Analysis System (REPA)" [I]. Based on the simulation results, this paper analyzes the failure process, characteristics and weighting of the overburden as the longwall retreat mining proceeds. The roadway's behavior including deformation characteristics, failure mechanisms, stress distribution in the surrounding rocks and the effects of various support systems on roadway stability were analyzed and studied. While simulating the rock failure process with REPA, the model stresses can be obtained through two approaches: (1) the stress is reflected by the grayscale of pictures in the model failure process and (2) the model stress can be obtained by muti-element information, which is one of the commands in RFPA system. Data files of stress can automatically be created, and curves of stress and displacement of each element can be displayed in each step of computation. Keywords: Rock Failure Process Analysis System (RFPA); roof control; roof to floor convergence; combined support

Jan 1, 2005