Search Documents

By Murali Gadde

Among different types of ground control problems associated with underground coal mining, those related to in situ stresses are the most common ones affecting the safety and economy of a mining operation. As a result, this has been the focus of many ground control research works done in the last three decades. This paper summarizes a recent work done on in situ stress related ground control issues of underground coal mine development workings. The approach used in this study was three¬-dimensional finite element modeling by an implicit code, ABAQUS/Standard. In the models, roof stability evaluations were made using Hoek-Brown rock mass failure criterion. Influence of the in situ maximum horizontal stress angle on the stability of both entry and intersection was examined to help determine the best development layout orientation. Also, the effect of in situ stress ratios on the stability of development openings was studied. To make the work more general, both 'low' and 'high' in situ stress fields were considered In general, the modeling results indicated that entries oriented in the direction of maximum horizontal stress were in the best condition while those oriented at 90° had the least stability. For intersections, the maximum and the minimum stability were seen at 0°/90° and 45°, respectively. However, under some combinations of input conditions, the best or the worst conditions were noticed at same other orientations as well. Based on these findings, layout design charts were prepared for both entries and intersections. It was also found that the change in ground conditions with change in layout orientation was more significant for 'low' in situ stress fields than for the higher ones. Change in the average safety factor with change in the ratio of in situ maximum horizontal to vertical stress resembled a lognormal distribution curve. However, the effect of the ratio of in situ maximum to minimum horizontal stress lacked such a clear trend for different input combinations considered.

Jan 1, 2004

By David A. Newman

In the 1950s, an underground limestone mine in the Camp Nelson Formation was developed from an outcrop exposure. The Camp Nelson Limestone met the requirements for DOT stone and aggregate. The mine ownership changed several times, which resulted in distinct mine designs in Level 1. Based upon the production requirements and an attempt to maximize limestone recovery from a single level, a variety of pillar dimensions and three mining heights (28 feet, 68 feet and 83 feet) were developed. This was sufficient prior to reaching the mineable extent of Level 1. Level 2 introduced previously unknown ground control challenges. These included: ??Pillar spalling and a significant back fall on the Level 1 - Level 2 decline; ??Laminated immediate back and the need to bolt the back on Level 2; ??Delamination of the back adjacent to the Level 1 - Level 2 decline resulting in bolt shearing, and floor heave in isolated areas of Level 2; ??Multiple level interaction, the need to design pillars based upon numerical modeling as columnization between Levels is infeasible: and ??Water inflow as the mine approached river. To meet the challenges, a testing program to determine rock strength and physical properties was implemented along with numerical (LAMODEL and FEM) modeling, and borescope inspections of the immediate back. The efforts to implement rock mechanics were re-focused as Level 2 approached its mineable limit and the initial attempt to drive a decline to Level 3 was unsuccessful. A second decline site was selected based on inter burden stability, a consistent shale parting for the Level 3 back horizon, results from numerical models of the immediate back and multiple level interactions, and the projected low water inflow. The mine is operating on Levels 2 and 3 with long-term planning and ground monitoring for Level 3.

Jan 1, 2014

By Revendra Awasthi

The application of a horizontal inclinometer and a tiltmeter to measure tilt, curvature, and deformations of shallow footings during mine subsidence is described. The measurements were taken during mining of a longwall panel in Southern Illinois and were supplemented with precision level survey data. Monitoring was conducted under a cooperative agreement between the Institute for Geotechnology at The University of Tennessee, Knoxville, the U.S. Bureau of Mines, the National Science Foundation, the Illinois Mine Subsidence Insurance Fund, and Old Ben Coal Company. Six different footings were constructed and instrumented at two sites; one above the panel centerline, and the second inside the edge of the panel in the anticipated zone of maximum tension. A brief description of the inclinometer casing and tiltplate installation is described, and the results obtained from the two instruments on a plain concrete footing compared. Observations of footing deformations and curvatures calculated from the inclinometer and tiltmeter data are also presented, and the results compared with observed structural damage.

Jan 1, 1990

By Khamis Y. Haramy

The U.S. Bureau of Mines installed surface and subsurface instruments at a mine site in Colorado to monitor and characterize the overburden response to longwall mining. Instrumentation included a time-domain reflectometry (TDR) cable, a multiple-point borehole extensometer (MPBX), vertical-deformation surface monuments, and in-mine pressure cells for monitoring abutment, pillar, and gob loads with respect to the longwall face position. The purpose of the study was to collect data that could be analyzed to correlate the design of the mine layout to the resulting overburden failure response. Determining the extent of caving and fracturing is important in the arid and semiarid Western United States because of the possible consequences to the fragile underground hydrologic systems upon which the land owners and users depend. This study is unique from past investigations because the overburden contains massive sandstone members that impose special conditions on the caving process and pressure redistribution above the longwall panels. This paper presents the results of this correlation study.

Jan 1, 1992

By Sheng Zhang

The compressive strength of coal in Yanlong mine area of China is less than 3 MPa. Basically, it is powdery. The roof and floor rocks are mudstone. Therefore this coal seam is a typical ?three soft? coal seam. Roof bolting cannot be used due to the very soft strata. When the conventional U-steel support was used, roadways deformation exceeded 30% of its original dimensions in some sections one half month after development. The required repair work was huge, seriously affecting the daily mine production. This paper describes how to support the soft coal roadways. The deformation characteristics of soft coal roadway were investigated. The conventional U-steel support is not subjected to uniform load, so the whole supporting structure must be strengthened. In addition, drilling holes in the coal seam can transfer high stress from near the ribs to the deeper parts of the surrounding strata, which is beneficial to the stability of the roadway. This new support method is to combine the strengthened U-steel support with pressure-relieving drill holes, providing an economic and efficient way to support the very soft coal roadways.

Jan 1, 2013

By David Bartsch

The Ohio Valley Coal Company (Ohio Valley) has operated the Powhatan No. 6 Mine in Belmont County, Ohio since 1972. Ohio University owns a 455-acre research farm over a portion of the Ohio Valley reserve containing 51 acres of old-growth forest known as Dysart Woods. In 1988, when Ohio Valley applied for a new mining area for its first longwall located several miles away from Dysart Woods, Ohio University claimed that mining at that distance would lower the regional water table and kill the old trees. In response, Ohio Valley began to study potential impacts from longwall mining on hydrology, soil moisture, and tree growth. Early studies examined the impacts of longwall mining on hydrology, soil moisture, and tree growth directly over mined areas compared to woodlots that were not undermined. A subsequent study examined tree-ring growth for a five-year period before and after longwall mining for several woodlots, some directly over panels and others at distances of up to 2000 ft away. No significant differences in growth rate associated with longwall mining were observed. New research was begun that compared longwall-mining impacts on groundwater hydrology, available soil moisture, and tree growth in two stands of mature trees located near Dysart Woods in order to confirm the earlier results. Using a test technique known as "Before-and-After-Controlled-Impact-Pairs," data was collected from one woodlot (test) that was undermined and from another (control) that was not undermined. Data collection began several years prior to longwall mining and has continued for several years after mining. The data for the test site shows that although the shallow and deep groundwater levels were affected by longwall mining, the soil moisture, vigor rating, or the growth rate of trees did not decline significantly compared to the control site where there were hydrologic impacts. The study shows that there are no known significant impacts to trees from longwall mining. The results of these studies were used by Ohio Valley to obtain State approval to longwall to within 300 ft of Dysart Woods

Jan 1, 2005

By D. Reddish

The combination of free standing steel supports, such as arches, and rock bolts (mixed support) has Frequently been in used in UK coal mine roadways when it is considered that the strata and/or environmental conditions would not be suitable for rock bolts solely. However, how such mixed support systems operate is not fully understood. Due to the differences in the support method provided by rock bolts and free standing steel, the total support generated is not simply a case of adding the contribution to the support of the roadway given by the two systems. This paper describes a numerical investigation into mixed support systems when used in coal mine roadways. A series of 2D and 3D geomechanical models are described and the method of modelling the rock bolts and steel supports in coal mine tunnels is discussed. The numerical models described include rock boltd only roadways, steel supported roadways and mixed supported roadways in a variety of geological and in-situ stress conditions. Conclusions are formed that allow an insight into mechanisms of strata reinforcement provided by the support systems modelled. Further to this, a review of the numerical modelling of pre-tensioned rock bolted systems is described identifying the contribution to support efficiency given by the adoption of tensioning in full column resin anchors. The results obtained highlight that the effectiveness of the pre-tensioned load is dependant on the rock mass quality and in- situ stress level at the site where it is to be used.

Jan 1, 2004

By Andrew Starkey

Ground anchorage systems in the form of rock bolts are used extensively throughout the world as supporting devices for civil engineering structures such as bridges and tunnels. It is widely recognized that non-destructive testing methods for ground anchorages need to be developed as a high priority [1 ], with only a small proportion of anchorages currently being monitored in service [2]. The condition monitoring of anchorages is a relatively new area of research, with the objective being a wholly automated or semi-automated condition monitoring system capable of repeatable and accurate diagnosis of faults and anchorage post tension levels. The GRANIT tm system developed by the University of Aberdeen is capable of measuring the integrity of ground anchorages and has won two major UK Awards - the National John Logic Baird Award for Innovation in 1997 and a Design Council Millennium Product Award in 1999. The normal procedure with the GRANIT tm system [3,4] is to train a neural network on dynamic response data that has been sampled from an anchorage over a range of post-tension levels. Further data is needed in order to test the neural network. The paper presents neural networks that have been trained on data taken from a number of anchorages on different sites, and the results of the diagnosis of these neural networks on new test data is presented. The results show that the cross-diagnosis of anchorages is possible, where a neural network trained on one anchorage is capable of successfully diagnosing the post-tension level for an anchorage of similar construction, and the high level of accuracy that can be attained with the GRANIT tm technique is shown. The paper also introduces a mathematical model of the GRANIT tm process.

Jan 1, 2001

By George B. Quaye

Conventionally, roadways in South African collieries are 6 to 7 m wide. This dimension is chosen so as to allow maneuvrability of appropriate mine machinery and equipment, to meet production requirements and to ensure roof stability. Over the last two decades, a great deal of research effort has been expended to understand the behaviour of roadways in different strata within this width range. The results have improved the understanding of the strata behaviour to such an extent that 6 m wide roadways are developed with a high degree of confidence. With the advancement of technology and the quest to mine at a lower cost, some mines in South Africa have started considering the benefits of other types of mine machinery that will require much wider roadways to ensure optimum productivity. The roadways required will have to be about 10 - 14 m wide. The challenge confronting these coal mining companies is the potential instability that might be associated with such wide roadways. This dilemma is aggravated by the fact that, apart from theory, nothing is known about the expected behaviour of such wide roadways. This led to experimentation at a selected site in a South African coal mine where 10 m and 14 m wide roadways were developed and monitored. This paper highlights the experimental procedure adopted, discusses the results obtained, compares the prediction of elastic theory to reality and set the precedence towards understanding the behaviour of wider roadways in South Africa.

Jan 1, 2001

The purpose and current practice of cable trusses in underground coal mines is briefly outlined and details of various cable truss designs are presented. The main part of the paper describes the in-situ performance of cable trusses installed as secondary supports in gateroads and recovery roads of longwall coalfaces. The performance analysis is based on the results of in-situ monitoring carried out at a number of sites at two underground coal mines within Australia. Truss performance has been assessed as load developed in relation to roof convergence, face position and time. Additionally, the influence of strata conditions, installation pattern/density, roadway layout and geometry have been taken into account. An analytical model has been developed to predict truss loads. The principal variables are listed and the basis of the model is described. Based upon behaviour observed in the field the model has been progressively upgraded and validated against measured performance. Guidelines on truss performance and factors which influence it are presented and the implications of these to the use of cable trusses is discussed. Possible methods for improving truss performance in certain strata conditions are outlined and some comments are made on the value of cable trussing compared to cable bolting in these situations,

Jan 1, 1992

Previously, a variety of risk rating systems were used on different mines. However, these were mostly site specific and geology based systems. The purpose of developing a uniform rating system, to be used on all Anglo Coal open cast mines, is to provide an unbiased, standard and quantifiable assessment of the risk from highwall and lowwall failures. This takes into account relative differences in the importance of hazards, as experienced on each mine as a result of different combinations of geotechnical factors and mining conditions. The system is based on critical geotechnical and other parameters that have been identified by mining personnel and rock engineers. The primary advantage of this risk rating system is that all open cast mines in Anglo Coal use an almost identical system, which enables the user to compare their risk to the risk at neighbouring mines and/or other open cast mines. The system can be adjusted to meet local, mine specific requirements. The implementation of this new system (a computer program that automatically calculates the risk) has been made as practical and easy to use as possible. Therefore, this tool can be used by personnel from other mining disciplines not directly related to rock engineering.

Jan 1, 2004

By David I. Hoyer

It is shown that by monitoring longwall leg pressures in real time, warning can be given for significant weighting events and the formation of roof instabilities, such as roof cavities, several hours in advance. Longwall Visual Analysis (LVA) is a software package that continuously monitors shield pressures and shearer position in longwall mines. LVA has been running on 19 Australian longwalls for up to four years, and as a result a very substantial database of shield pressure trends in a wide range of longwall situations has been collected. This database has been analyzed to develop indicators that will give operators and geotechnical engineers advance warnings of developing conditions such as weighting events and difficult roof conditions. LVA displays live charts of data, such as shield leg pressures, loading rates, and yield frequencies. Data analysis techniques were applied to historical data records from multiple longwall sites in order to develop a ?Cavity Risk Index? (CRI). The CRI indicates the risk of roof cavities developing, and it is based on pressure trends that indicate significant yielding and loading rates spanning a region of relatively low support. Case studies from different longwalls are given, showing how the CRI can give real-time advance warning of the formation of roof cavities with their anticipated location on the face. The limited number of case studies done so far indicate that the predictions have a high degree of reliability, but more work is required to quantify this.

Jan 1, 2011

By Duk-Won Park

The excavation of a longwall panel causes a continuous stress redistribution in the surrounding strata for every face advancement. The understanding of the behavior of rock to high level of stresses is instrumental to the structural design of underground mines. In order to achieve a realistic analysis of the behavior of strata, the three-dimensional finite element method is frequently used. Also the model developed for the analysis has to be designed large enough to represent the influenced strata in the study area and a sufficient number of elements has to be used to provide detailed information on the stresses and displacements. Due to the size of the model and its numerical solution the CRAY X-MP/24 supercomputer has been used for this study. The mine site selected for the analysis is a coal mine located in the Black Warrior Basin in Alabama. The mine has two longwall sections at a depth of 2,000 feet with various dimensions of chain pillars, including yield pillars. Various research programs at this mine have been carried out by Park et. al. ( 1984 ). Therefore data were already available on the geology, and physical properties of rock and coal. In addition a rock testing program has been carried out to obtain rock mass classification parameters. The progressive failure technique has been utilized to simulate stress redistributions. The failure criterion after Hoek and Brown ( 1980 ) which is based on rock mass behavior was used for the iterative technique. Simulated stress redistributions are therefore very realistic. In order to automate the process involved in the application of progressive failure technique, a computer program has been developed. The combination of a large scale three-dimensional finite element model and the automation of progressive failure simulation provided a tool that can generate a large amount of information related to the behavior of rock and coal as a response to a longwall mining operation.

Jan 1, 1989

By Ding Xu Chu

There are many methods developed for measuring the crustal stress in China. Among them only two methods have been adopted in practice, i.e., overcoring method (for which the sensors include: Piezo-magnetic stress gauge, steel-ring strain cell, 3-dimensional hollow-inclusion stress ,gauge, and Leeman's-like stress gauge) and hydraulic fracturing method. For the former method, one of those sensors is installed in a borehole, 36 mm in diameter, then prestressed, and finally overcored with a drill bit of 130 mm in diameter. After that the deformation of the borehole wall is measured, from which the in-situ stresses are determined. In order to avoid the errors resulting from the difference in elastic modulus for various kinds of rocks as well as from the installment of the cells, we have developed a technique to calibrate the sensor on-spot using a confining pressure calibrator and produced a very good result. For the later method, the measurements are achieved by isolating a certain section of a borehole and then injecting water to pressurize it till a tensile break is induced. It is identical to the typical technology used internationally. For many years, through field observations and a large number of laboratory experiments, we believe that the most efficient way of stress measurement for engineering purposes is the overcoring method using Piezo-magnetic stress gauge. It is characterized by stable and reliable measurement values, high accuracy and high adaptability. Taking the measurements in the intact rock mass as an example, the measured stress magnitudes are within accuracies of 8% and the errors in orientation are about 5 degrees. It can even be used perfectly in deep water. Up to now, we have performed in-situ stress measurements in more than 70 sites and obtain more than one thousand sets of data. The deepest depth used in the overcoring method is 80 m in vertical borehole and 780 m in tunnels.

Jan 1, 1987

By Bruce W. Jack

An extensive underground roof-monitoring program was conducted in order to determine the roof strata behavior under various conditions. In total 29 sites at 5 different collieries were monitored using the sonic probe extensometer. Results showed that, in drill and blast sections, there are often pre-existing openings in the roof prior to the installation of the support. An estimated 42 per cent of the total roof displacement monitored in drill and blast sections took place prior to the installation of support. A comparison between roadways and intersections indicated that, for a 40 per cent increase in the span, taken across the diagonal of art intersection, relative to the roadway width, the magnitude of the displacement in the roof increased by a factor of 3. Total displacements measured were relatively small, only 2 reaching double figures of 12 mm. The remainder were all less than 7 mm. The results also showed no evidence of a substantial increase in the height of the bed separated, potentially unstable roof strata, as is the case in the high horizontal stress-driven beam-buckling mechanism experienced in for instance some Australian coal nines. Therefore, it was concluded that, in South African collieries, the effects of horizontal stresses is generally relatively small compared to overseas collieries.

Jan 1, 2000

By Christopher Phillips

In light of recent events in the mining industry, there has been an increasing demand for technology to detect underground voids and abandoned mine workings. This paper summarizes the use of geophysical methods for this application. Geophysical methods have been successfully employed in the detection of underground voids in several disciplines, including foundation analysis, road and infrastructure analysis, and darn analysis, but is not yet being widely employed by the mining industry. The principal reasons are that the combination of the complex geological setting of a mine, mine design, surface conditions, and improper choice of geophysical method often makes the task of locating abandoned mine workings with geophysics a frustrating, time consuming, and often unsuccessful venture. While there are several geophysical methods that have been demonstrated for the successful detection of abandoned mine workings, there is still no 'silver bullet' to solve the problem in every case. The choice of geophysical method to detect abandoned mine workings should be made on a site specific, and sometimes target specific, level. This paper reviews current methods, and introduces recently developed methods, for the detection of underground voids and abandoned mine workings.

Jan 1, 2003

By C. J. H. Brest van Kempen

The techniques developed should provide a useful tool, not only during the initial formulation of a suitable bolting plan for a new section, but also for periodic check¬ing on the utilization factor of hardware installed in the roof. Indications are that with present practice, utilization seldom exceeds 507.. Retro-fittable bolter equipment now available (FCBS?) allows doubling of the utilization factor in many cases. We are also introducing a computer pro¬gram based on the material outlined in this paper. This program can save a great deal of time in examining the real effect of implementing alternate bolting plans or using different installation techniques. It allows fine-tuning of bolt lengths, spacing and installation tension to mini¬mize roof support cost, while maximizing safe life of the mine opening. We have developed a procedure which allows easy, site-specific quantification of the need for reinforcement of a mine roof. The concept is based on the forma¬tion of a direct link between theory and empirical data to custom-fit each mine section. In its simplest form, the proce¬dure requires only recording of roof bolt torques in a sample working place (16 to 25 bolts) several times during the first week or so after initial bolting. The way in which the torque pattern changes during this time can reveal whether or not the bolts carry enough tension to maintain stability in that specific roof. From the same data, the nature of the anchorage horizon is derived. Specifically, shale or limestone can be distinguished from sandstone. If the procedure is repeated a few times (within the same mine section) with different bolt installation tensions, we can numerically characterize the roof in terms of one single value: an "effective angle of internal friction". This number can then serve to calculate trade-offs in bolting plan design, such as bolt length, bolt spacing and optimum bolt tension. Additional refinement is possible if a sagmeter is installed in the sample work¬ing place being monitored and if bolt anchorage capacity is determined. The lat¬ter can be done automatically on each bolt as it is being installed, using a system we developed and patented. Alternately, a number of pull tests could be performed. Using the sagmeter, bolt torque and anchor¬age data, it is possible to project the safe life of the supported opening. The details of the procedures described apply specifically to tensioned roof bolting, but a brief discussion paints the way for a similar analysis of full-column resin bolting also.

Jan 1, 1986

By William Monaghan

Over the period 2000 to 2003, roof falls have accounted for 4 to 14% of the fatalities in underground mining operations. The National Institute for Occupational Safety and Health (NIOSH) is conducting research to reduce the frequency, exposure, and risk of these events through an ongoing program of field and laboratory studies. One area of research involves the evaluation of polyurethane grouting technology that is commonly used to stabilize fractured mine roof strata. Concurrently, NIOSH is conducting work to evaluate the application of ground penetrating radar for advanced delineation of problematic mining areas. In this study, NIOSH partnered with Sub-Technical, Inc. who injected a polyurethane grout (also known as glue) into a roof area of NIOSH's Safety Research Coal Mine. The mine roof area was scanned using ground penetrating radar technology before and after grout injection in an attempt to determine the extent of grout infiltration. A comparison of the pre-and post-grouting radar records showed a significant change at a mine roof depth of about four to five feet. The interpreted radar records were then compared with drill core information, borescope evaluation of roof-bolt holes in the study area, and underground observations. At this site, the interpretations of the radar records correlated with data obtained from the core holes, borescope evaluations and underground observations. This study showed that ground penetrating radar technology can be a useful tool for detecting changes in mine roof due to the injection of the grout.

Jan 1, 2004

By Syd Peng

It is necessary to fully understand roof geological features in order to design a proper roof support system for underground coal mines. These geological features include: rock type, rock strength. rock layer interfaces, voids, cracks, and bed separations. Traditionally, engineers have relied heavily on the use of surface borehole log data to identify geological features. Since surface boreholes very expensive to be drilled in close spacing, log data are often insufficient to provide detailed information on the roof geology. Recent advances in control technology have made a large amount of roof bolter drilling data available to mine personnel. These data can be obtained during normal roof bolt installation cycle with little or no interruption in mining operations. This research project has developed several methods to identify geological features in a mine roof from measured drilling parameters. Power trend line analysis can be used to locate discontinuities and interfaces in mine roof. Power averaging can be applied to determine the relative strength of roof strata. Thrust trend line analysis can be used to locate fractures in mine roof. The results of these methods are combined to produce a mapped roof geology In a production environment, manually interpreting and managing collected drilling parameters is not practical since hundreds of holes will be drilled during a production day. A new software package, MRGIS, has been developed to allow mine engineers to make use of the large amount of roof drilling parameters for roof support design. An actual underground test site is presented to demonstrate the analysis and display capabilities of MRGIS.

Jan 1, 2003

By Daniel W. H. Su

This paper presents the results of an extensive geomechanical testing and monitoring program conducted at a longwall panel. The field program included the monitoring of roof caving sequence and mechanism, surface subsidence, change of pillar stress, roof displacement and entry convergence, and strength characterization of the overburden rocks. The response of eight headgate pillars and the adjacent entries was monitored as the longwall face approached and passed the instrumented locations. Overburden response to longwall mining was monitored using time domain reflectometry (TDR) technology; and, the height of the highly fractured zone above the gob was determined by postmining drilling. Good correlation was found between the height of the highly-fractured zone and the TDR, subsidence, and pillar stress data. The results provide a detailed picture of the response of overburden strata and chain pillars to longwall mining. A preliminary model representing the overburden strata behavior at the test site in response to the longwall mining is proposed.

Jan 1, 1987