Search Documents

By Terry L. Logan, Arfon H. Jones, James C. Seccombe

Deeply buried coal seams [greater than 3000 ft (914 m)] are difficult and sometimes hazardous to test and complete due to coal sloughing, formation pressure anomalies and coal fine generation. Data collected while stimulating two deep coalbed methane wells located at the Gas Research Institute/Resource Enter¬prises, Inc. "Deep Coal Sean Project" test site in the Piceance Basin, Colorado, is presented in this paper. A single thick coal seam was completed openhole in each well. Core data, reservoir data, in-situ stress measurements, and pre-stimulation calibration test data were collected at the site to use in the design of the fracture stimulation treatments for both wells. A nitrogen foam fracture fluid treatment was selected for the first well and a linear gelled water for the second well. Treatment pressures were monitored with a downhole quartz pressure transducer. Atypically high treating pressures were observed, possibly indicating coal fines plugging at the fracture tip or increase in fluid viscosity caused by interaction of the generated coal fines with the fracturefl uid. In addition, a comprehensive fracture diagnostic effort was employed during the fracturing of the second well; namely, triaxial borehole seismic, seismic televiewer, hydraulic impedance monitoring, gamma ray log (in conjunction with radioactive additives in the sand), and temperature log. The results indicate a vertical fracture was created parallel to the face cleat as expected.

Jan 1, 1986

By Michael J. Friedel

The scale-dependent hydraulic properties in a fractured porphyry copper oxide deposit are investigated for relevance to in situ leach mine (ISLM) design. In most well field designs, mine operators assume that hydraulic properties represent a continuous spatial function, or continuum. The problem, however, is that the representative elemental volume, the volume over which hydraulic properties are described as a continuum, is a domain (if it exists) that occurs between end members representing varying degrees of heterogeneity. At the Cyprus Cas a Grande mine, transmissivity fluctuations are spatially correlated suggesting that at the scale of ISLM, the hydraulic process is heterogeneous and a typical continuum representation is inappropriate for design. Alternatively, a conditional stochastic approach using the simulated annealing (SA) technique is deemed useful for the imaging of heterogeneous hydraulic properties. Specifically, SA preserves transmissivity extremes and spatial complexity, both necessary for accurate conditioning of a flow simulator. Also, the stochastic continuum approach provides an avenue whereby uncertainty (or risk) may be addressed. Currently, the SA weaknesses are that it is computationally time consuming, and uncertainty may increase when simulating under conditions of statistical isotropy. Recognizing that ISLM exerts a dynamic influence on hydraulic properties with time, the mine design should be reevaluated at intervals throughout the evolution of the leaching process.

Jan 1, 1993

By F. Habashi

The Republic of South Africa is a heterogeneous mixture of Black Africans, Afrikaans, British, Indians, Malayans, French Huguenots, and many others from Europe and Asia. A decisive date in its recent history is the collapse of the Apartheid Regime in 1994. For a metallurgist, South Africa is the country of diamonds, gold, platinum, and many other metals. In 1887 Cecil Rhodes (1853-1902) was able to take control of the De Beers Mining Company after the discovery of diamonds at Kimberly in 1866. It was there where the so-called School of Mines was inaugurated in 1896.

Jan 1, 2010

By G. France

The Blair Athol Coal Mine (BAC) is a large open cut operation in the Bowen Basin of Queensland, Australia. Current mine capacity is about 11 million tonnes per annum (Mtpa) of export coal. On-line analysis at BAC consists of two Coalscan 9500s installed directly on the output of the crusher plant and immediately before the product stockpiles, while a third Coalscan 9500 is installed on the transfer conveyor feeding the train loading bin. The two product Coals cans have a dual purpose. The first is to provide real time coal quality data directly back to the mining operations. The second is that of modeling the product stockpile with accurate on-line information. This modeling enables both production and coal quality personnel to accurately examine the coal quality of each stockpile with a degree of resolution which previously had never been achieved.

Jan 1, 1999

Mineral processing plant operators are faced with the necessity to choose between many different possibilities for plant improvement. Only a few such possibilities, however, can be tested on the industrial site. Steady-state simulators make it possible to assess the effects of several different flowsheet modifications in a few days, thus helping the process engineer to make his choice implement the solution that seems the most appropriate and check it. The example described here is the crushing and grinding circuit of the Shila Gold Mine, jointly owned by CEDIMIN SA and BUENAVENTURA SA, in Peru. Several possible modifications for the purpose of increasing capacity have been simulated and the results assessed in terms of technical quality, investment costs and energy consumption. The best solution indicated by the USIM PAC simulator was implemented and gave a 20% increase in capacity with a pay-back time of two months.

Jan 1, 1993

By Rodolfo V. de la Cruz

The in-situ deformability of a highly jointed basalt rock mass was determined by two distinctly different methods: one, by the NX- borehole jack method where the displacements of opposing curved platens were related to the applied hydraulic pressures, and; two, by the modified Goodman jack method where the tangential strains on the borehole walls were related to the induced tangential stresses. The modulus obtained by the modified Goodman jack method were much higher than those obtained by the NX- borehole jack method. To explain the discrepancy, the influence of fractures and test variables such as depth, orientation, hole number and applied pressure on the calculated modulus of the rock mass were analyzed by factorial analysis and it was found that the orientations and depths of measurement has statistically significant effects. The in-situ deformability values obtained by non-linear regression analysis were also found comparable with other measurements and empirically predicted values for the basalt rock mass.

Jan 1, 1982

By Donald C. Wotring, Douglas A. Gabriel, Michael G. Vitale

"The Northeast Ohio Regional Sewer District (NEORSD) recently completed the 24-foot diameter Euclid Creek Tunnel using a steel-fiber reinforced concrete segmental lining. During construction HMM, the McNally/Kiewit JV, CSI/Hanson JV, and the NEORSD performed a test program to evaluate replacement of steel fiber with synthetic fiber. A section of synthetic-fiber-reinforced cast-in-situ lining was also placed as part of the permanent works for the starter and tail tunnels. Laboratory and field testing were performed on two complete segmental rings reinforced solely with synthetic fibers. This paper summarizes the testing program, construction, and results of the synthetic-fiber-reinforced CIP lining and concrete segments. INTRODUCTION The principal feature of the Euclid Creek Tunnel (ECT) project is a CSO storage tunnel that is one component of the Northeast Ohio Regional Sewer District’s (NEORSD) Easterly CSO storage and conveyance system. The tunnel, shafts, and appurtenant facilities will be used for the collection and storage of CSOs from the northeastern part of Cleveland, Ohio and subsequent conveyance to the NEORSD’s Easterly Wastewater Treatment Plant for treatment. The ECT project includes five drop shafts that extend as deep as 220 feet below the ground surface. The ECT alignment and shaft locations are shown in Figure 1. Traditionally in northeast Ohio, tunnel excavations were supported with a two-pass system using steel ribs and timber lagging, followed by cast-in-place concrete. Control of rock overbreak proved difficult with large-diameter two-pass operation, and invert degradation led to train derailments. To mitigate these risks, the ECT was supported using one-pass, precast, bolted, gasketed concrete segments reinforced with steel fiber alone. Tunneling operations were very successful and experienced no significant delays or claims. As a result of the positive ECT experience with steel fiber-reinforced segments, Hatch Mott MacDonald, LLC (HMM), McNally/Kiewit (MK) joint venture, CSI/Hanson (CSI/H) joint venture, and the NEORSD performed a test program to evaluate replacement of steel fibers with synthetic fibers in segmental rings. This paper presents the laboratory and field testing program, construction, and results of the synthetic-fiber-reinforced cast-in-place (CIP) lining and concrete segments."

Jan 1, 2016

By Marek Wilczewski, Kristine Uhlman, Darrel Sipe

With the end of active copper mining in 1983, the extensive underground mine workings and the Berkeley Pit, one of the largest open-pit mines in the United States, began to flood. Daily in- flow to the pit is about five million gallons per day, with the water level rising at a rate of 30 feet per year. To support the remedial investigation and feasibility study, a six-layer, three-dimensional MODFLOW-based ground water flow model was constructed to simulate the 9,100-acre site. The vertical domain of the model extended over 1,060 feet of elevation difference and consisted of a finite difference grid of 89 rows by 54 columns. All work was PC- based. Model boundaries were assigned to correspond to natural hydrologic features such as geologic contacts, faults, and surface water features. The fully calibrated model was approved by the State of Montana and the U.S. Environmental Protection Agency (EPA) for use in the site remediation. The computer model was used to determine ground water flow velocities and contaminant travel times within the alluvial sediments adjacent to the Berkeley Pit. The purpose of the model was to predict future alluvial ground water flow directions should acid- and heavy metal-laden flood waters filling the Berkeley Pit rise up and enter the Alluvial Aquifer.

Jan 1, 1996

By G. R. Hart

The expected 1990 Clean Air legislation is providing electric utilities with a series of challenges and decisions as the utilities prepare strategies to comply with the resulting regulations. This paper addresses the strategy development of a coal-based utility --the legislation, the process used, the fuel issues, the options available, and the decisions to be made.

Jan 1, 1991

By Jr. Watts

The American Mining Congress and the U.S. Bureau of Mines have formed a collaborative research team to develop, implement, and evaluate a comprehensive control strategy to reduce diesel particulate matter concentrations without degrading other air quality parameters at an underground noncoal mine. Other participating organizations include Caterpillar, Inc., the Mine Safety and Health Administration, and the University of Minnesota. After extensive baseline information and air quality data are collected, available control strategies to reduce diesel particulate matter exposures will be implemented, individually or in combination, and evaluated. This paper discusses the objectives and protocol of the collaborative effort to evaluate diesel particulate control technology.

Jan 1, 1995

By R. V. Ramani

In 1970, of the 603 million tons of coal produced in the United States, 339 million tons, or 56%, were produced by under- ground mines. While the ratio of underground to surface production has been decreasing in the last few years, it is anticipated that a 60:40 ratio of underground to surface-mined coal will remain for some time. Underground coal operators are continuing to invest in new mines and are interested in increasing the efficiency of all their operations. One area for improvement is in mine planning and design, particularly in the area of selection of equipment for operation. Because of the availability of a wide variety of equipment, a fair degree of selectivity can be exercised in the choice of equipment for a particular job. However, such a choice must be made on the basis of technological facts and forecasts related to the mining operation. If the mining conditions can be reasonably predicted, along with a mining plan, it should be possible to insure the selection of the right equipment for the particular application. In order to increase the efficiency of underground coal operations, it is necessary to understand not only the operating system in detail, but the inter-relationships between system components and the operating environment. With such an understanding comes the application of simulation and other operations research techniques to plan and operate mining systems. Computer simulation studies have been successfully adapted to underground coal mining, and applications by Prelaz et al. (1965), and Manula and Sanford (1969) are some that are being used by the mining companies. However, a need still exists for better understanding of certain intra-system and system-environment interactions in order that computer simulation programs may be provided with better input data for more effective application. This paper deals with one aspect of the coal-winning system in need of better definition, namely, studying the performance of continuous miners.

Jan 1, 1973

By I. F. Walder

Mill tailings from skarn-type base metal deposits were studied in order to ascertain potential element mobility in response to weathering. Hypogene ore minerals are sphalerite, galena, and chalcopyrite, showing minor supergene oxidation to smithsonite, cerussite, and covellite. Gangue minerals are pyrite, pyrrhotite, magnetite, hematite, andradite and grossular gamet, hedenbergite, calcite, ankerite, and quartz. Foremost of the eleven tailing piles studied, the hypogene sulfide minerals show no or only incipient post-mining oxidation. Iron oxides and hydroxides form the main oxidation products in the tailings and are enriched in heavy metals. A distinction between pre-and post-mining oxide phases may be obtained based on petrographic observations which distinguish whole-grain versus partial grain replacement. Zn and Cd do not appear to be enriched in the weathering derived oxidation minerals and will be more easily leached from the tailings than other metals.

Jan 1, 1994

By D. L. Kuck

Water ice pillars far underground mine roof support can be frozen and/or maintained and/or melted on demand. The system to do this consists of a refrigeration brine chiller, brine circulation system and disposable plastic containers. Fusion expansion, resilience to dynamic loads, plastic deformation under stress, and non-contamination of coal or ore are unique properties of ice. Lower labor and material costs are economic advantages of ice far mine structural support. Ice brattices can become ice pillars on retreat. For safety, ice pillars can be placed (by remote control, if necessary) in hazardous sites without human entry.

Jan 1, 1988

By R. Debkowski

The current underground infrastructure of an old monumental salt mine along with using it as a tourist, museum, nature, resort, conference and cultural events place is presented in the paper. At present, mainly in the monumental part of mine, only a small part of the historical chambers, which together with galleries form a tourist route available to visitors. Moreover, the essential activities aimed to make the tourist route more attractive and to change the decor of the underground sites are discussed.

Jan 1, 2006

By J. Noll, D. Yantek, J. Organiscak

The Office of Mine Safety and Health Research of the U.S. National Institute for Occupational Safety and Health (NIOSH OMSHR) conducted laboratory testing of a self-tramming, remotely controlled mobile Dry Scrubber (DS) that J.H. Fletcher and Co. developed under a contract with NIOSH OMSHR to reduce the exposure of miners to airborne dust. The scrubber was found to average greater than 95 percent dust removal efficiency with disposable filters, and 88 and 90 percent, respectively, with optional washable filters in their prewash and post-wash test conditions. Although the washable filters can be reused, washing them generated personal and downstream respirable dust concentrations of 1.2 and 8.3 mg/m3, respectively, for a 10-min washing period. The scrubber’s velocity-pressure-regulated variablefrequency- drive fan maintained relatively consistent airflow near the targeted 1.42 and 4.25 m3/s (3,000 and 9,000 ft3/min) airflow rates during most of the laboratory dust testing until reaching its maximum 60-Hz fan motor frequency or horsepower rating at 2,610 Pa (10.5 in. w.g.) of filter differential pressure and 3.97 m3/s (8,420 ft3/min) of scrubber airflow quantity. Laboratory sound level measurements of the scrubber showed that the outlet side of the scrubber was noisier, and the loaded filters increased sound levels compared with clean filters at the same airflow quantities. With loaded filters, the scrubber reached a 90 dB(A) sound level at 2.83 m3/s (6,000 ft3/min) of scrubber airflow, indicating that miners should not be overexposed in relation to MSHA’s permissible exposure level — under Title 30 Code of Federal Regulations Part 62.101— of 90 dB(A) at or below this airflow quantity. The scrubber’s washable filters were not used during field-testing because of their lower respirable dust removal efficiency and the airborne dust generated by filter washing. Field-testing the scrubber with disposable filters at two underground coal mine sections showed that it could clean a portion of the section return air and provide dust reduction of about 50 percent at the face area downstream of the continuous-miner operation.

Jan 1, 2016

By Lawrence D. Ramspott

A test of retrievable geologic storage of spent fuel assemblies from an operating commercial nuclear reactor is underway at the Nevada Test Site (NTS) of the U.S. Department of Energy his generic test is located 420 m below the surface in the Climax granitic stock. Eleven canisters of spent fuel approximately 2.5 years out of reactor core (about 1.6 kW/canister thermal output) were emplaced in a storage drift along with 6 electrical simulator canisters. Two adjacent drifts contain electrical heaters, which are operated to simulate within the test array the thermal field of a large repository. Fuel was loaded during April-May 1980 and initial results of the test will be presented.

Jan 1, 1981

By Collin L. Stewart

Published subsidence data for the western United States is limited in comparison with data for the east. This paper summarizes the results of a subsidence monitoring program above two longwall panels at the Foidel Creek Mine located in northwest Colorado. The monitoring area is characterized by overburden ranging from 1000 ft to 1100 ft in thickness. The surface slope parallels the dip of the bedding at approximately 5 deg. Average mining height is 9 ft. Smax averaged 3.4 ft. Draw angles averaged 15 deg for up-dip ribsides and 19 deg for down-dip ribsides. A site-specific profile function is developed from the data.

Jan 1, 1986

By W. P. Diamond

The Bureau of Mines has been investigating several techniques, including the use of horizontal and vertical boreholes, to remove gas from coal in advance of mining. Horizontal boreholes drilled from underground workings as part of the mining cycle have been shown (Finfinger, 1980; Hagwood, 1983; Perry, 1978; Prosser, 1981; Thakur, 1980; VonSchonfeldt, 1982) to be very effective in providing short-term, immediate relief from high methane emissions. This technique has been widely accepted in the coal mining industry, but it does require close coordination to integrate the drilling and subsequent gas drainage and disposal into the projected mine development plan. Vertical boreholes can be placed several years in advance of mining to predrain gas from coalbeds over relatively large areas (Dunn, 1984; Elder, 1975; Lambert, 1980; Steidl, 1978; Stubbs, 1979). The vertical borehole technique has the additional advantage over horizontal boreholes of allowing work to be performed on the surface instead of in the more restrictive underground environment. However, except for the relatively large scale vertical borehole programs for both mine safety and commercial production in the Black Warrior Basin of Alabama (Dunn, 1984; Lambert, 1980; Stubbs, 1979), the technique has been underutilized. The primary reason for this seems to be a combination of the current economic climate in the coal industry, legal questions as to the ownership of coalbed gas, and potential roof damage from the stimulation treatments required to increase the characteristically low permeability of coalbeds to enhance gas production. The question of potential roof damage is the subject of this paper.

Jan 1, 1985

Adsorption of acrylamide based homo and copolymers on hematite was investigated as a function of phe nature of the polymer charge and functionality of the polymer. Effect of addition of sodium dodecylsulfonate and dodecylamine hydrochloride was also studied and was determined to result in an increase or decrease in the amount of polymer adsorbed depending on, the charge characteristics of the surfactant and the polymer, pH of the suspension, concentration of the various species and the order in which these species were added to the system. The surfactant adsorption under given conditions on the other hand, was found not to be affected by the presence of the polymer molecules. The data is analyzed to elucidate the mechanism of adsorption of polyacrylanide type polymers on hematite both with and without the surfactant species king present in the system.

Jan 1, 1982

By R. L. Pozzo

A previous investigation showed that corrosion currents estimated from polarization curves for the pyrrhotite-grinding media system under abrasion correlated well with corrosion currents estimated from marked ball wear test data by applying the Faraday's Law. Freshly abraded metal debris were magnetically attracted to pyrrhotite and lowered the rest potentials of the mineral particles, thereby affecting the corrosive wear. The investigation was extended to explore the interactions between a nonmagnetic sulfide mineral, pyrite, and abraded metal debris and their effects on the corrosive wear mechanism. The electrochemical behavior of a three-electrode system involving pyrrhotite, pyrite and grinding media was also investigated as a first step towards elucidating the nature of interactions that occur in the grinding of complex sulfide ores.

Jan 1, 1987