Search Documents

By A. Habibi

The FMC Westvaco Trona Mine is located near Green River, Wyoming and has an annual production of 4.5M tons. Trona is an evaporite mineral that is processed into several products, mostly soda ash. The underground mine has two active development panels and one longwall (LW) panel. The mining horizon is about 500m below surface and the surrounding strata liberates methane. Three surface-based, blowing fans provide ventilation air as a positive pressure system. The mine operates a 225m long LW face, built by Joy Mining Machinery. Headgate and Tailgate developments are driven with four entries. The recovery room, at the end of each panel, is 8m wide with three access chutes. Additional recovery room support comes for concrete blocks used with a center to center spacing of 1.5m. As the LW enters this pre-driven recovery room there are notable responses and shifting ground stresses. This study was undertaken to measure the ground response using seven vibrating wire displacement transducers. These devices were used to monitor the convergence as the LW approached the recovery room. The methane concentration in the air ventilating the recovery room was also monitored. The correlation between convergence and gas liberation was then studied. The results show that the convergence varies from 0.1m to 0.25m along the length of the recovery room. Ventilating the recovery room becomes critical as methane is liberated from oil shale as the more plastic floor material is disrupted. Appropriate methods are employed to ventilate the recovery room.

Feb 23, 2014

By J. B. Yianatos, G. S. Dobby, J. A. Finch, A. R. Laplante, R. Espinosa-Gomez

The question is posed as to why columns typically have a collection zone 10 m high (H) by 1 m in diameter (D). Three geometry dependent factors are considered: degree of mixing, Np; volumetric bias rate, B; and volumetric gas rate, G. Increasing H:D decreased Np and B, which improves performance but decreases G, which causes the column to approach overloading. Taking typical column operating conditions, it is concluded that a collection zone H:D of 10:l is a reasonable compromise.

Jan 1, 1987

By K. Fleck

Energy West Mining Co. (EWMC) has implemented a geologic program for improving stability and support requirements along deep two-entry longwall gateroads at its Deer Creek Mine operations located near Huntington, UT. Together with geotechnical monitoring and concurrent review of mine seismicity in cooperation with MTI staff, it has become possible to improve longwall layout designs for two seam extraction of the Hiawatha and Blind Canyon seams. The geologic program consists of surface and in-mine exploration drilling, surface and in-mine geologic mapping, rock mechanics testing and detailed measurements of changes in depositional and structural conditions during development of every longwall gateroad. The geotechnical program consists of underground measurements at seven locations in two neighboring mining districts located in the Hiawatha and Blind Canyon coal seams under moderate to deep cover. Within the last five years, additional measurements, including data on seismicity and face conditions, have been incorporated into the data collection program for verifying the in situ coal strength and load transfer mechanisms for improving two-seam designs and support systems.

Jan 1, 2012

By D. A. Meyer

The long and arduous process of bringing aggregate produced in Mexico to the Gulf Coast of the United States really began in the 1970s when the first exploratory trips were taken by Vulcan's geologists. It was not until the middle of the 1980s that all of the elements of the project seemed favorable and the largest capital investment in Vulcan's history was given the green light. The history of the project will be covered along with a discussion of the role that market forecasting played in the process. Is this the first of many or a once in a lifetime project? In July 1987, Vulcan and its joint venture partner broke ground in Mexico for a world-class limestone quarry and crushed stone production facility. This project is the largest ever undertaken by Vulcan's Construction Materials Group, with a total cost of over 200 million dollars -a cost shared equally by Vulcan and its joint venture partner, Ingenieros Civiles Associados, or ICA, a diversified Mexican company which is also the largest construction firm in Latin America.

Jan 1, 1995

By M. S. Basich, J. S. Scope1, J. H. Raeder

During 1983, The Youghiogheny and Ohio Coal Company's lost-time-incidence rate was 8.1, equal to the average for underground bituminous operators. How- ever, one half of all lost-time injuries were low back, back and neck related. In reviewing these results, we determined that substantial improvement could be made. We investigated existing back schools and the possibility of opening an in-house clinic. In September 1984, we began The Youghiogheny and Ohio Coal Company's Back Care Program. The objectives of the program are to reduce the number of back injuries incurred at the work site, hasten recovery time, decrease medical and workers' compensation costs and provide the employee with a thorough understanding of his problem. A state-of-the-art clinic capable of treating injuries to the spine and extremities has been established at the work site. The clinic is staffed by a licensed physical therapist and is offered to all employees on a voluntary basis under physician referral. The approach to treatment is multi-phasic. For the typical patient, the initial goal is to reduce pain and correct dysfunction. Treatment modalities such as auto-traction, extension exercises, ultra sound and moist heat are frequently used. During this period the patient is given extensive education regarding his problem. As soon as more vigorous activity can be tolerated, a work-hardening pro- gram consisting of job simulation activities designed to improve flexibility, strength and functional capability is begun.

Jan 1, 1986

By Siyu Song, Yanhong Wang, Guohua Gu, Linbo Huang

In this study, the effect of cations, Na+ and Mg2+, in saline water on copper flotation in the presence of calcium bentonite was investigated. It was found that as the concentration of NaCl was increased, the copper recovery initially decreased and then increased to above 99%, while the copper grade initially increased and then decreased. In contrast, as the concentration ofMgCl2 was increased, the copper recovery continuously increased, while the copper grade continuously decreased. The variation of copper recovery and grade was mainly attributed to the synergistic effect of pulp rheology and flotation solution chemistry. The underpinning mechanisms are the compressing electrical double layer and ion-exchange interaction between saline water and bentonite, which occur at the same time. Using salinewater slightly affected the pulp rheologywith a decrease in copper recovery at low NaCl concentration. Increasing the concentration of cations in saline water might even facilitate the flowing out of exchangeable cations, especially divalent cations, from the interlayer space of bentonite to the solution, resulting in the decrease of copper grade at high salt concentration.

Sep 10, 2020

By R. L. Kloberdanz

Compania Minera Disputada de las Condes S.A. (Disputada) is proactively implementing closure and reclamation planning activities at its mining and beneficiation facilities (mining facilities) in Chile where regulations governing mine reclamation are not yet fully in place. These activities are being implemented to improve currently employed measures to protect human health and the environment and to enhance reclamation and facilitate future closure with regard to these areas when mining is completed. As part of this process, Disputada, with the assistance of Shepherd Miller, Inc., developed recommendations and guidelines for future closure and reclamation of the Disputada sites. These recommendations and guidance incorporate planning and operational and post-operational design considerations and practices, and standards used by the mining industry and regulatory agencies around the world. The criteria presented in the guidance are based on achieving conditions that will be suitable for the anticipated post-mining land use. This paper discusses the process and approach taken, and the results.

Jan 1, 1999

By PDF

Flotation columns are widely used in mineral processing and coal preparation industry today. Mathematical modeling of flotation columns has conventionally been done using axial dispersion or tank-in-series models. However, for design and scale up purposes these models are not adequate enough because they do not provide detailed information of the flow fields within the column. This paper presents a Two-Dimensional, Two-Phase. Fluid-dynamic Model and its numerical solutions for some cases encountered in column flotation. The MAC (Marker and Cell) method was employed to obtain the numerical solutions, and based on this method a computer code COLUMNFLOW was developed. The simulated flow field reveals the presence of a circulation flow structure in flotation columns, which could be one of the main reasons for mixing in column flotation. The effects of some parameters such as superficial gas and liquid velocities on the characteristics of the flow structure in flotation columns were also tested with the numerical model.

Jan 1, 1994

By P. Tsang

To gain insight into the current status of pillar design practice in the underground coal mines of United States, a survey has been undertaken in the late 1993 and early 1994. A total of 552 room-and-pillar mines and 75 longwall mines have been surveyed to collect general, geological and mine plan information. The collected information are critically analyzed with special emphasis on the pillar design criteria adopted in these mines. A safety factor analysis has also been carried out for the pillars in room-and -pillar mines.

Jan 1, 1995

By D. Robert Weir

The complex mineralogy of the Porgera resource has a pronounced effect on process selection for the recovery of refractory gold and silver. Intimate association of gold with pyrite necessitates a high degree of sulphur preoxidation in order to achieve acceptable levels of gold recovery. Acid pressure oxidation has been demonstrated to be the only commercially proven process capable of achieving the required level of pyrite oxidation. Gangue mineralization dictates preconcentration of the sulphides to limit the acid consuming capacity and carbon dioxide generation during oxidation. However, the relationship between concentrate sulphur grade and gold recovery to concentrate ultimately governs the optimum degree of sulphide preconcentration.

Jan 1, 1986

By Langtry E. Lynd

The titanium dioxide pigment industry in the United States has always relied to varying degrees on imported titanium concentrates. Dependence on foreign ilmenite was especially high (generally over 85% of consumption) until 1942, when large-scale U.S. production of ilmenite began, and has since ranged from 12% to 47%. Rutile import reliance was generally in the 45% to 80% range until the early 1960's, when increased use in the chloride pigment process raised dependence on imported rutile to over 90% in most years since 1963. Import reliance of zircon, obtained almost entirely as a byproduct of titanium mineral production, has generally ranged from about 30% to 65% of consumption. This paper will examine the history of U.S. sources of these heavy mineral commodities, and will discuss the potential U.S. future supply in view of changing industrial uses and processes and the anticipated development of new heavy-mineral-sand processing operations, such as those at Richards Bay in the Republic of South Africa and in Sierra Leone.

Jan 1, 1978

By Dai Wang

Stoppings are necessary ventilation control devices for effective air distribution underground. However, one of the major problems underground mining has is that every stopping is a potential leaking source. Since air always flows from a point of high pressure to one of lower pressure, and the total pressure at every point in intake airways is higher than that in the return airways, air will always tend to leak from intake to return (Tien, 1996). In many mines, less than half of the air entering the mine actually gets to the working areas; the rest of it simply short-circuits directly to return airways through leaky stoppings instead (Timko and Thimons, 1983). Leakage through a stopping occurs because of pressure drops across the stopping and available leaky path in stoppings. Empirical equation has been widely used to characterize the relation the amount of leakage and variables that affect leakage. However the use of this equation requires accurate information for constants which are not always readily available. It is the attempt of this paper to derive an equation similar to the Atkinson Equation that can readily be applied to characterize pressure-leakage relationship for any given stopping.

Jan 1, 1998

By Jose M. S. Ramos

This paper describes the slope stabilization procedure at Cauê Mine, Companhia Vale do Rio Doce - CVRD, Itabira, State of Minas Gerais, Brazil. Cauê Mine, is a large open pit, to produce about 41 million tons of iron ore during 1974, and an intensive program of investiga Lion was carried out to provide the basic data for stabilizing its slopes, The ultimate rock slope in the W area will be about 400 m high with dipping angles decreasing gradually from top to bottom of the pit. The investigations started in 1969 and since then many geologists and engineers, from both CVRD and Geotécnica S/A., assisted by international consultants, have given their contribution to the achievement of solutions. It is hoped that this paper may contribute to the slope stability of other mines in tropical climate.

Jan 1, 1974

By T. J. Toy

The topography reconstructed following land disturbance is the foundation for all other reclamation practices. As the manufactured drainage basins, hillslopes, and stream channels approach a steady-state condition, the amount of adjustment of these landforms by geomorphic processes following reclamation decreases. As the adjustment required to establish a steady-state condition decreases, the prospect of reclamation success increases while the prospect of site maintenance decreases. Careful topographic reconstruction is a good investment.

Jan 1, 2002

By F. A. Renninger

The mineral aggregate industry is the world's largest mining and processing endeavor, yet it is graced with little of the romance or public awareness that accompanies mention of gold, silver, iron, copper, uranium, or aluminum mining efforts. Much of this reaction is undoubtedly due to the fact that the uses to which crushed stone and sand and gravel are normally put are not fully recognized or appreciated by the general public. Few individuals ever have occasion to purchase mineral aggregates for anything other than use for decorative shrubbery beds or walkways. They may, however, buy ready-mix concrete for a new patio, bituminous concrete for a new driveway, concrete blocks, or other building materials for a new room and never realize that the primary ingredients of their purchases are either direct or indirect products of the mineral aggregate industry. The average person driving past an operating crushed stone quarry or an active sand and gravel pit rarely realizes the economic impact the industry, represented by that operation, exercises on the general economy. He is not aware, nor does he really care, that elements of the modern comfortable environment to which he has grown accustomed rely to a great extent on the products of the crushed stone and sand and gravel industries Iron and steel, glass, cement, agriculture, and highway and building construction are but a few of the major industries to whom the products of the mineral aggregate industry are basic. Without these industries or without the stone, sand, and gravel basic to them, most of the major elements of our modern day civilization would be non-existent.

Jan 1, 1968

By R. M. Enick

A novel liquid-liquid separation for the recovery of free or liberated gold from mixtures of fine particles was evaluated. The separation, conducted at ambient temperature and a pressure of about 1000 psi a, was based on the difference in wettability of precious metals and minerals. Contact angle results indicated that in the presence of water and liquid CO2, gold, platinum and silver had intermediate wettability. Minerals such as quartz and magnetite, however, were hydrophilic. Therefore fine gold particles. -325 mesh, that were mixed with water and liquid CO2 dispersed in the CO2 or agglomerated at the H2O-CO2 interface while the minerals tended to remain in the aqueous phase. Best results were obtained when these fine gold particles were liberated, were not agglomerated in slimes, were not adhering to minerals, and were not coated with minerals.

Jan 1, 1998

By P. T. Bissert, J. P. Ducarme, J. L. Carr, A. K. Smith

The continuous mining machine is a key piece of equipment used in underground coal mining operations. Over the past several decades these machines have been involved in a number of mine worker fatalities. Proximity detection systems have been developed to avert hazards associated with operating continuous mining machines. Incorporating intelligent design into proximity detection systems allows workers greater freedom to position themselves to see visual cues or avoid other hazards such as haulage equipment or unsupported roof or ribs. However, intelligent systems must be as safe as conventional proximity detection systems. An evaluation of the 39 fatal accidents for which the Mine Safety and Health Administration has published fatality investigation reports was conducted to determine whether the accident may have been prevented by conventional or intelligent proximity. Multiple zone configurations for the intelligent systems were studied to determine how system performance might be affected by the zone configuration. Researchers found that 32 of the 39 fatalities, or 82 percent, may have been prevented by both conventional and intelligent proximity systems. These results indicate that, by properly configuring the zones of an intelligent proximity detection system, equivalent protection to a conventional system is possible.

Jan 1, 2016

By P. T. Bissert, J. P. Ducarme, J. L. Carr, A. K. Smith

"The continuous mining machine is a key piece of equipment used in underground coal mining operations. Over the past several decades these machines have been involved in a number of mine worker fatalities. Proximity detection systems have been developed to avert hazards associated with operating continuous mining machines. Incorporating intelligent design into proximity detection systems allows workers greater freedom to position themselves to see visual cues or avoid other hazards such as haulage equipment or unsupported roof or ribs. However, intelligent systems must be as safe as conventional proximity detection systems. An evaluation of the 39 fatal accidents for which the Mine Safety and Health Administration has published fatality investigation reports was conducted to determine whether the accident may have been prevented by conventional or intelligent proximity. Multiple zone configurations for the intelligent systems were studied to determine how system performance might be affected by the zone configuration. Researchers found that 32 of the 39 fatalities (82%) may have been prevented by both conventional and intelligent proximity systems. These results indicate that, by properly configuring the zones of an intelligent proximity detection system, equivalent protection to a conventional system is possible. INTRODUCTION Underground coal miners are exposed to a variety of hazards on a daily basis. Among coal and rock dust exposure, high noise levels, roof and rib falls, and the potential for fires and explosions, operating and working with heavy machinery poses a significant risk to miner safety. One of the most hazardous jobs is operating or working nearby a continuous mining machine (CMM). According to Mine Safety and Health Administration (MSHA) statistics, 39 miners have been fatally struck or pinned by a CMM since 1984. In an effort to prevent future striking and pinning fatalities from occurring, proximity detection systems have been developed and are now required on all operating CMMs in underground coal mines with the exception of full-face CMMs [1]. Commercially available proximity detection (cPD) systems are based on the principle of magnetic flux density (B-field). Typically, four magnetic field generators are positioned on a CMM, and personal alarm devices (PADs) are worn by the miners that detect magnetic flux density difference. As a miner wearing a PAD gets closer to the machine, the flux density increases. Zones can be constructed around the machine so that an alarm will trigger on the PAD based on the flux density."

Jan 1, 2016

By Hesam Dehghani, Farid Alimohammadnia, Nima Babanouri, Mokhtar Kalhori

In open-pit mining, blasting pattern design is performed to achieve a desired degree of fragmentation for loading, hauling, and crushing operations. Inappropriate fragmentation of rock will result in numerous problems such as incurring extra costs for secondary blasting, production interruption, etc. Wetness of the blast holes is one of the most important factors, which can cause the inappropriate rock fragmentation. Lowering ambient temperature in the vicinity of the explosion, the presence of water in the hole adversely affects the quality of the explosive while dissipating part of the explosion energy, ending up with inappropriate fragmentation problems. In the present research, in order to study blast-induced fragmentation conditions in Baba-Ali Iron Ore Mine, three scenarios were considered: explosion of ammonium nitrate with fuel oil (ANFO) in dry hole, explosion of ANFO in wet hole, and explosion of the emulsion in wet hole. For this purpose LS-DYNA, a numerical simulation code was used. Results of the present research showed that, compared to the explosion of ANFO in wet hole, the explosion of the emulsion produced more uniform distribution of fragment size, while the explosion of ANFO in dry hole resulted in fewer large fragments.

By Alan Rhodes

This study is initiated to investigate the efficiency of separation of mineral slimes using electroflotation as compared to that of column and conventional flotation techniques. Important parameters such as collector concentration, pH, current density, aeration rate, etc., have been studied. The results indicate that electroflotation can be used more efficiently in processing rutile slimes (10 µ) under certain operating conditions.

Jan 1, 1982