Search Documents

By Paavo Eerola

In May of 1984, it was decided that Outokumpu Oy would design and build a new nickel flotation mill to process ore from the newly discovered Enonkoski mine in eastern Finland. Since there hart peen a number of successful process charges in the existing mills, the design effort included the study and incorporation of several new developments, including all-autogenous grinding, "flash flotation", lane cell roughing, large cell cleaning and a computer-based, profit optimizing, process control system. The paper discusses the background and results of those studies, and a description of the resulting mill which will begin production in 1986.

Jan 1, 1985

By Zhuang Jianming, Liu Qinxia, Yuan Mingliang, Mei Xiangong, Chen Jin

Up to now, the leaching of manganese carbonate ore is usually performed at high temperature of 363K and the leaching rate is lower than 90%. Although in laboratory test, the leaching rate is only 90%. This paper introduced an improved method for leaching of manganese carbonate ore. Certain ammonium salt was added to the pulp to raise the solubility of Mn2+ and reduce the adsorption quantity of Mn2+ on the ore surface. Experimental results show that a leaching rate over 95% can be obtained at the temperature >273K. The activation energy is calculated to be 7.15 KJ/mol and is lower than that of normal leaching technique. The effects of the parameters, such as particle size, pulp density and initial acid concentration on the process results are investigated. A leaching rate higher than 95% can be obtained under the following conditions: particle size below 0.25mm, leaching time 60 min, stirring speed higher than 960 r.pm. H2SO4:MnCO3>1 .2, pulp density 105-205 g.L-l. A kinetic model was deduced, verifying with actual experiments. It showed that the model can describe the leaching process successfully.

Jan 1, 1995

By Frank Pollard

The Australian coal industry over recent years has experienced the situation whereby exploration and mine development are moving into geographical areas where the coal seams have never been mined to any extent in the past, if at all, and particularly where there is no history of experience in preparation of these seams. Additionally, the demands have been such that the development of a mine up to production stage should proceed with minimum delay. This is a situation which is of some importance and concern, in view of the coal quality requirements now experienced within world markets which can only be met, in most cases, by careful preparation. Costs are such that the preparation plant should operate as required by the situation and with maximum efficiency, which means that laboratoty information of breakage and washability characteristics which are required for preparation plant design should be accurate and available as soon as possible, even to a certain extent during the progress of the exploration.

Jan 1, 1981

By F. Vallianatos

The main objective of the present investigation is to demonstrate the potential of ERT (Electrical Resistivity Tomography) and HVSR (Horizontal to Vertical Spectral Ratio) methods as geophysical tools for the monitoring of subsurface cavities. The survey sites are located in Akrotirion Peninsula, almost 7 km east of Hania town in Crete Island, Greece. At this site, the surface expression of a known cavity with a diameter of about 25 m is visible. The true geometrical characteristics of the cavity were unknown since there are no boreholes in the area. The focus of this survey was primarily of a qualitative nature and the objective was to determine if ERT and HVSR could be used to identify and map near surface cavities (less than 30 meter in depth) in a limestones kartsic area such as Akrotirion Peninsula. A 2D/3D model of the resistivity distribution is given for the area under investigation. Furthermore, analysis of microtremors data provides a profile of the seismic response of the tectono-karstic voids.

Jan 1, 2006

By Sertaç Dündar, Bilgehan Kekeç, Arif Emre Dursun, Niyazi Bilim

"Estimation of rock drillability is vital for mining and boring operations. For this purpose, many researchers have developed various models and equations to estimate rock drillability. Most of these models aim to determine the drillability of rock and the penetration rate by using the physical and mechanical properties of rocks. Although drillability primarily depends on rock properties, other parameters have an impact on drillability as well. One of these parameters is the rotation speed of the bit. This study investigates the effect of rotation speed of the bit on drilling performance. Drilling tests were performed in the laboratory using rotary core drilling and a diamond drilling machine. The relationships between the physical rock properties and the penetration rate were investigated on 15 different rock types and four different rotation speeds were applied to determine the effect of rotation speed of bit on drilling. The uniaxial compressive strength, density, and P wave velocity show strong correlations with the penetration rate. In addition, if the values of the physical and mechanical properties of the rock increase, the effect of the rotation speed on the penetration rate decreases, i.e., increasing the rotation speed of the bit slightly affects drillability on hard and solid formations. 1. Introduction Drilling is one of the most essential operations in the mining industry, beginning from the exploration phase and continuing throughout all stages of production to the end of mine life (Taheri et al. 2016). In addition, drilling is widely using in the construction industry and other engineering operations. Various drillholes (blastholes, injection holes, borehole, diamond wire holes in natural stone mines, etc.), are needed during development and production activities in underground and open-pit mines as well as in dam, tunnel, road construction and sewage systems. For effective drilling operations, it is first necessary to gather information about the formation to be drilled. Drilling should then be performed after selecting appropriate drilling equipment and drilling parameters (thrust, pressure, rotational speed, flushing). Prediction of the drillability of rocks is vital for planning and performing the drilling process. Although, drilling is affected by several factors, the most important ones are related to the geological and mechanical properties of formation (Protodyakonov 1963, Paone et al 1969, Tandanand and Unger 1975, Pathinkar and Misra 1976, Rabia 1985, Perrin et al 1977). Determining the penetration rate is vital for planning a project and calculating the operation costs. The prediction of drilling affects the selection of drilling equipment, the efficiency of drilling equipment, project costs and the process of drilling operations."

Jan 1, 2017

By R. R. Guzman

In this study, the "Mine Project Risk Management" methodology, MPRM (Botin et al. 2011), has been applied to characterize the sources of uncertainty and to quantify risk in the mining engineering stages of Block Caving mining method. As the result, rock mass caveability and ore fragmentation were identified as the two most relevant parameters of this process and a methodological model has been developed to quantify the risk associated to each of these two parameters. Furthermore, the applicability of the proposed model has been validated using as a case study the Chuquicamata Underground Mine Project in Chile.

Feb 23, 2014

By Harold Stocker

INTRODUCTION This presentation is concerned with the administrative and technical capability of the Atomic Energy Control Board (AECB) to assure compliance with the individual exposure limit for radon daughters (currently 4 WLM per year). It is not concerned with the epidemiological bases for setting the exposure limit. Moreover, the intent is to show how sophisticated methodologies and advanced technologies, applied to radon daughter concentration measurements in uranium mines, convey the spirit of compliance by providing better estimates than do the historical methods. These better estimates mean that more accurate and more precise estimates of each worker's exposure are determined using these more modern methods and devices. The estimates so derived should provide more convincing evidence to an individual worker that his assigned exposure is a valid indicator of his true exposure. In addition, a perspective on the exposure estimate in relation to the exposure limit is given as further evidence that an exposure limit is not the dividing line between "safe" and "unsafe" exposures. A brief description is given of the compliance aspects of the Atomic Energy Control Regulations and of the limitations of purely statistical non-compliance procedures. Most of the emphasis of the paper will be placed on the uncertainties associated with conventional radon daughter exposure determination and the means being employed (and anticipated) to reduce these uncertainties. NON-COMPLIANCE Under current Atomic Energy Control Regulations (1978), the annual individual exposure limit for radon daughters is given without reference to the possible methods of sampling and calculation of radon daughter exposure and without any reference to possible uncertainties or their magnitudes. This is common in such statutes, the details of sampling, calculation, error analysis, and so on, being left for licence conditions or provided as a specific guideline to the licensee on the matter of compliance with the Regulation. Since the exposure limit is contained in the Regulations, compliance with it is absolute, as with any other law. In Canada, a state of non-compliance with the radon daughter exposure limit exists when an exposure (attributed to an employee) is reported by the licensee to exceed the limit. No uncertainty in the measurements or in the overall determination of exposure is reported nor is any requested. Removal of the worker and the loss of his services are the immediate and direct penalty suffered by the licensee for failure to maintain the exposure at, or below, the limit. A worker may be re-instated to employment for the balance of the reporting period only if the licensee can assure the AECB that further significant exposure to the worker will not ensue. In other jurisdictions, such as the United States, non-compliance is defined on a statistical basis. For example, NIOSH, the National Institute for Occupational Safety and Health presents procedures for calculating the 95% Lower Confidence Limit (LCL) in order to "compare the results of occupational environmental sampling to an occupational health standard and make a decision with a known chance of making an incorrect decision that a state of non-compliance exists" (Leidel and Busch, 1975). (In the nomenclature of this presentation, exposure limit would be used in place of "standard", in the NIOSH sense). Furthermore, it is emphasized in the NIOSH document that such numerical comparisons "are necessary only if the sample mean is greater than the standard". The NIOSH document points out, quite correctly, that the "statistical procedures presented below will not detect and do not allow for analysis of highly inaccurate results, i.e., systematic (non-random) errors or mistakes ... If a systematic error is known to exist in an instrument or analytical procedure then correct the sample mean of the data before analyzing for non-compliance". It is certainly not the purpose of this paper to criticize the sophisticated statistical approach to non-compliance as given in the NIOSH document or in similar approaches used in other jurisdictions. Rather, the purpose is to approach, with some introspection, the question of the determination of exposure by the employer for his employee and especially the employee's understanding of, and confidence in, the accuracy of the exposure determination and its relation to the exposure limit. DETERMINATION OF EXPOSURE Historically, in uranium mines, exposure to radon daughters for an individual miner

Jan 1, 1981

By D. W. Park

Underground openings resulting from coal mining activities have been a serious cause of subsidence problems in the Warrior coalfield of Alabama, which is the 11th largest coal-producing state in the United States (National Coal Association, 1986). The problem will be even more serious in the future because 17 Gt (19 billion st) of Alabama's 22 Gt (24 billion st) of coal reserves are classified as an under- ground resource (Tolson et al., 1982). Subsidence data in this area has been scarce com- pared with other coalfields (Conroy, 1980; Dunrud and Osterwald, 1980; Gentry and Able, 1978; Hunt, 1979; King and Gentry, 1979). This paper discusses the results of a study of subsidence overlying two longwall mines that contrast each other. One of them (Mine #1) is a shallow longwall mine where the coal strength is very high, and the other mine (Mine #2) is extremely deep with a low strength of coal.

Jan 1, 1987

By Subhash Bhagwat

The definition of high sulfur coal varies from plant to plant and is subject to changes over time as the environmental regulations change. In plants constructed after September 1978 hardly any domestic coal can currently be burned without the use of Flue Gas Desulfurization (FGD) because a 70 percent reduction in potential S02 emission is mandatory even when the potential emission is less than 0.6 lbs. S02/106 Btu heat input. On the other hand older power plants may in many cases be legally emitting up to 6 lbs. S02/106 Btu or more under some State Implementation Plans (SIP). The Clean Air Act requires, however, that in the long run all stationary sources of S02 pollution must abide by the ceiling of 1.2 lbs S02/10 Btu heat input.. Coals with a potential to exceed this limit must, therefore, be considered as high sulfur coals. Such a definition would be unrealistic because many SIP's aim at an emission level of 1.8 to 2.0 lbs. SO2/106 Btu for existing plants and a stricter limit does not appear to be enforceable in the next 5 to 10 years. As a result, coals with an emission potential of greater than 2.0 lbs of S02 per 10 Btu heat input are considered high sulfur coals for the purpose of this investigation. Based on this definition and the 1984 actual consumption of coals by U.S. electric utilities (table 1) only 7 out of the 24 coal producing states could be categorized as low sulfur states. The actual S02 pollution, however, depends on total tonnage of a type of coal as well as the sulfur content of the coal. Table 1 also indicates that only 6 states--Kentucky, Illinois, West Virginia, Ohio, Pennsylvania and Indiana-account for nearly 77 percent of S02 pollution potential in the United States. These 6 states have therefore been chosen for this investigation.

Jan 1, 1986

By J. A. Botín

Investment decision for large mining projects imply an enormous financial risk and therefore, require a more complex risk evaluation methodology taking into account all sources of uncertainty from each process in the project value chain. Generally, the main sources of risk are those related to uncertainty on grade and other techical variables of the orebody. In this study, conditional simulation is applied to develop a risk management model to quantify and to manage financial risk associated to uncertainty on the grade of the orebody. The model was validated in case study on a real porphyry copper orebody in Chile.

Feb 23, 2014

By A. J. Guse

The primary limiting factor for hoisting capacity from great depths is the self-weight of steel wire ropes. Steel wire ropes are very suitable for mine hoisting due to their high strength and durability, but have the negative characteristic of a low strength/weight ratio. Also, as hoisting depths increase, the service life of steel wire ropes decreases due to the higher stresses and physical effects on the ropes. The significantly higher strength/weight ratio of synthetic ropes offers the primary advantage of hoisting a larger payload with a similar size rope and hoisting plant. The beneficial properties of synthetic ropes could be used to improve the overall economics of deep underground mining both for new deep shaft projects and for existing mining operations expanding to deeper orebodies. A research and development program has been initiated to evaluate the suitability of a fully synthetic rope for the mine hoisting application.

Feb 23, 2014

By B. J. Scheiner

The Bureau of Mines, U. S. Department of the Interior, is conducting research on a dewatering technique for fine particles generated during the mineral beneficiation process that will recover a portion of the water now being lost using conventional waste disposal methods and significantly reduce the time required for land reclamation. The technique utilizes a flocculant, polyethylene oxide (PEO), that forms strong stable flocs that can be dewatered rapidly on static and/or rotary screens. In field tests, phosphate clay waste has been dewatered from a nominal 2.5 percent solids to greater than 20 percent solids. In other field tests, coal-clay waste has been dewatered from a nominal 3 percent solids to greater than 55 percent solids, in addition, small-scale continuous tests have shown that bentonitic clays can be dewatered from 12 percent solids to 40 percent solids.

Jan 1, 1983

By Vincent J. Murphy

INTRODUCTION Geophysical applications to engineering projects are usually considered for reconnaissance exploration, and for some preliminary design phases. Recent experience indicates a growing need and a greater number of requests for measurements during construction. This is particularly true where seismic velocity values are related to strength properties of rock. Typical project objectives during construction are: dike and tunnel realignments required by surprise conditions encountered during foundation preparation; checks on grouting effectiveness which require velocity measurements before and after grouting; and dynamic moduli measurements along the walls of tunnels and deep excavations. This paper considers one of the on-site seismic applications that is rather simple and straightforward, and yet has few references in the literature. The specific objective is the measurement of seismic velocities (both "P" waves and "S" waves) for determining the thicknesses and dynamic moduli values of loosened zones of tunnel wall rock. PRE-EXCAVATION SEISMIC METHODS The seismic methods suitable for engineering project studies are well known and especially suited for routine site reconnaissance; these are illustrated in Fig. 1. The seismic refraction profile with a

Jan 1, 1997

By R. Duckett, D. Salisbury, R. Dorey

The Kennecott Ridgeway Mine in South Carolina is scheduled to complete mining and ore processing in the last quarter of 1999. Tailings are disposed in a 300 acre, lined tailings impoundment. To facilitate closure and reclamation, modification of the tailings impoundment operation has been adopted. Mining involved the sequenced development of two open pits. In 1996 mining of the South Pit was completed and backfilling of the pit with waste rock from the North Pit was initiated and will continue until mining ceases. Both pits will be reclaimed as fresh water lakes. This paper presents the physical, geochemical and hydrogeochemical evaluation of the operational and post operational management of the project. Comparison of the operational monitoring data against predicted performance are reviewed.

Jan 1, 1999

By Donald B. Buddecke

The large walking dragline has been the most commonly used overburden-stripping equipment in Texas lignite mines. These draglines, operating on the highwall side of the pit, can excavate to a depth of 45 m. Considerable overburden rehandling is required beyond 30 m and may reach 100 percent by 45m. As pit depth increases, dragline operation also becomes more complex, with two or three passes being necessary to make a cut 30 to 40 m wide. Multiseam operations also require extra passes. At pit depths greater than 45 m, the dragline must be operated also from a spoil bench. This can be difficult in the unstable alluvial deposits in which lignite occurs.

Jan 1, 1985

By O. M. Arafat, J. A. Finch

"The Functional Performance Equation calculated from a plant grinding survey defines two distinct ball mill circuit efficiencies and how they relate to total production rate through the target grind size. The survey data are also used to calculate a complete ball mill size distribution model, represented by the energy specific grinding rates, not just through the target grind size, but through all the size classes. Cyclone separation performance is represented by individual size recoveries to underflow. When these two unit operation performances are entered into the circuit modelling program (Streamline™), along with the circuit feed rate and size distribution, all the circuit survey size distributions and mass flows are perfectly regenerated by the program. The many issues associated with the historical Epstein (breakage-selection) models are eliminated. Once the circuit program is populated, pump and cyclone performance changes can be evaluated using a step-by-step procedure in order to maximize Classification System Efficiency. Mill water use and media sizing opportunities are also diagnosed in order to maximize Mill Grinding Efficiency at the size of interest. An example is provided. This circuit analysis and modelling system, and related training, is provided through a web-based application. INTRODUCTION Since its development (McIvor, 1988), the Functional Performance Equation for ball milling has facilitated new understanding of industrial circuit cause and effect relationships, leading to significant strides in operational performance. Success stories of this refreshing approach to plant circuit performance improvement are now too numerous to list. Finch and McIvor (circa 1986) also discovered that the Functional Performance “Mill Grinding Rate” at the size of interest was the same cumulative grinding rate that is calculated from mill feed and discharge size distributions using a first-order rate equation. By calculating these cumulative grinding rates for all screen sizes, a complete ball mill model is generated (as used by Finch and Ramirez, 1981). Others in industry, Hinde and Kalala (2009), for example, have noted the same. Lacking the complexity needed to maintain their interest, most researchers have ignored this model, broadly opting instead for Epstein’s (1948) characterization of grinding as a chemical reaction, combining “selection rate” and “breakage size distribution” functions. The much simpler ball mill model presented here has previously been incorporated into a proprietary circuit modeling program (McIvor, 2005) and used for plant improvement work (for example, see McIvor and Finch, 2007, and McIvor, 2014). Now, by combining this extremely business-friendly ball mill model with optimization criteria from Functional Performance Analysis, a circuit modeling system (including the needed supplementary steps to assure successful plant implementation of circuit design changes) is at the disposal of every plant metallurgist, grinding equipment/material provider, and circuit designer."

Jan 1, 2017

By A. R. Laplante

A novel methodology to estimate gold recovery by gravity is presented. The methodology makes use of a population balance model which represents gold liberation, breakage and classification behaviour and applies pre-concentration and recovery performance curves to gravity-recoverable gold to predict overall recovery. Derivation of the necessary parameters is explained and demonstrated using data from an actual gravity circuit and one projected application. The methodology makes it possible to estimate the performance of circuits with large gold circulating loads and relatively low unit recoveries (e.g. jigs), or with high recoveries on a bleed of the circulating load (e.g. Knelson concentrators).

Jan 1, 1994

By M. S. Frasad

The State of Minnesota is interested in stimulating the development of clay resources and recently supported a two year project to collect data on geological, mineralogical, processing, economic and environmental aspects of such potential developments. This paper presents the .various process options adopted on the bulk samples collected from the Minnesota River Valley area which is a primary deposit and contains a major silica fraction. A standard test flowsheet involving degritting, dispersion, HGMS, and cycloning was developed and for some samples yielded an acceptable filler grade product. Secondary streams containing relatively high grade kaolin but of coarse size were also obtained. Improvement in particle size distribution and in physical properties related to paper product specifications (brightness, viscosity) were obtained by size reduction processes. Market and economic considerations for kaolin consumption in the upper Midwest are analyzed. Current markets for paper grade kaolin in Minnesota were briefly discussed.

Jan 1, 1990

By R. Hogg

A standard procedure for determining size-specific gravity distributions of fine coal (including the -400 mesh fractions) by sieving and centrifugal sink-float separation is described. The significance of using a centrifugal sink-float technique and the effect of the magnitude of the centrifugal force on the separation of fine coal are confirmed in the present study. The relative merits of cumulative versus incremental sink-float are discussed. The procedure is evaluated quantitatively using data obtained for the products of froth flotation of -100 mesh coal.

Jan 1, 1994

By G. Newman, C. D. Sellars, E. A. Portfors

Power for mine operation in remote locations is usually provided by diesel generators. For gold mines where processing is normally desirable on-site, power requirements can be significant and the operating cost for diesel generation then becomes an important factor in mine feasibility. If a suitable site is available, a small hydroelectric power facility near the minesite can provide a significant portion of the mine power requirements. The hydrological, engineering and economic factors involved in small hydroelectric power development are described in this paper. Capital costs are minimized by run-of-river hydro development which does not require a dam and reservoir and has less environmental impact. During periods of low flow, diesel generators are used to make up the power demand. The hydrologic analysis required to determine unit energy costs is described and technical requirements for linking the hydroelectric power facility with diesel generation are outlined. Case studies are presented demonstrating the economic advantages of a small hydro installation. One case study is for a proposed gold mine in British Columbia and the second is a large operating gold mine overseas, for which the hydroelectric power scheme is presently under construction .

Jan 1, 1987